Wacker Neuson HI35 User manual

Operator’s Manual

Indirect-Fired Air Heaters

HI35

HI60 / HI60HD

HI90 / HI90HD

Type HI35, HI60 / HI60HD, HI90 / HI90HD

Document 5200024469

Date

0417

Version 04

Language

EN

5200024469

Copyright notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the

machine. Any other type of reproduction is prohibited without express

written permission from Wacker Neuson Production Americas LLC.

Any type of reproduction or distribution not authorized by Wacker

Neuson Production Americas LLC represents an infringement of valid

copyrights. Violators will be prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their

respective owners.

Manufacturer

Wacker Neuson Production Americas LLC

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original instructions

This Operator’s Manual presents the original instructions. The original

language of this Operator’s Manual is American English.

wc_tx003882gb_FM10.fm

3

Foreword

HI35 – HI90

Foreword

SAVE THESE INSTRUCTIONS—This manual contains important instructions for

the machine model below. These instructions have been written expressly by

Wacker Neuson Production Americas LLC and must be followed during installation,

operation, and maintenance of the machine.

This manual covers the machine with the following item number:

Machine

identification

A nameplate listing the model number, item number, revision number, and serial

number is attached to this machine. The location of the nameplate is shown above.

Serial number

(S/N)

For future reference, record the serial number in the space provided below. You will

need the serial number when requesting parts or service for this machine.

Machine Item Number Machine Item Number

HI35 5200019337

HI60 5200019338 HI60HD 5200019339

HI90 5200019340 HI90HD 5200019341

wc_gr012337

Serial Number:

wc_tx003882gb_FM10.fm

4

Foreword

HI35 – HI90

Machine

documentation

 From this point forward in this documentation, Wacker Neuson Production

Americas

LLC will be referred to as Wacker Neuson.

 Keep a copy of the Operator’s Manual with the machine at all times.

 For spare parts information, please see your Wacker Neuson Dealer, or visit the

Wacker Neuson website at http://www.wackerneuson.com/.

 When ordering parts or requesting service information, be prepared to provide

the machine model number

, item number, revision number, and serial number.

Expectations

for

information in

this manual

 This manual provides information and procedures to safely operate and

maintain the above Wacker Neuson model(s). For your own safety and to

reduce the risk of injury, carefully read, understand, and obser

ve all instructions

describe

d in this manu

al.

 Wacker Neuson expressly reserves the right to make technical modifications,

even

without notice, which improve the performance or safety standards of it

s

mac

hines.

 The information contained in this manual is based on machines manufactured

up until the time o

f publication. Wacker Neuson reserves the right to cha

nge any

portio

n of this information without notice.

 The illustrations, parts, and procedures in this manual refer to Wacker Neuson

facto

ry-installed components. Your machine may vary depending on t

he

require

ments of your specific region.

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and

modifications. The following definitions apply:

 Approved parts or attachments are those either manufactured or provided by

Wacker Neuson.

 Approved modifications are those performed by an authorized Wacker

Neu

son service center according to written instructions published by Wacker

Neuson.

 Unapproved parts, attachments, and modifications are those that do not

meet the approved criteria.

Unapproved parts, attachments, or modifications may have the following

consequences:

 Serious injury hazards to the operator and persons in the work area

 Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions about

approved or unapproved parts, attachments, or modifications.

2017_CE_HDXX_HIXX_en_FM10.fm

EC Declaration of Conformity

Manufacturer

Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue,

Menomonee Falls, Wisconsin 53051 USA

Product

Product category

Product function

Item number

HD50, HD70, HI35, HI60, HI60HD, HI90, HI90HD,

HI120, HI120HD

Heating Equipment

To heat air

5200019335, 5200019336, 5200019337, 5200019338,

5200019339, 5200019340, 5200019341, 5200019342,

5200019343

Directives and Standards

We hereby declare that this product meets and complies with the relevant regulations and

requirements of the following directives and standards:

2006/42/EC, 2006/95/EC, 2014/30/EU

EN 13842: 2004

EN 60335-1:2002 + A1:2004 + A11:2004 + A2:2006 + A12:2006 + A13:2008 + A14:2010

EN 60335-2-102:2006 + A1:2010

EN 60529:1991 + EN 60529 corr:1993 + A1:2000

EN 55014-1:2008

EN 61000-3-2:2007

EN 61000-3-3:1997 + A1:2002 + A2/IS\1:2006

Authorized Person for Technical Documents

Robert Raethsel, Wacker Neuson Produktion GmbH & Co. KG, Wackerstrasse 6,

85084 Reichertshofen, Germany

Menomonee Falls, WI, USA, 07.04.17

Original Declaration of Conformity

Keith Herr

Vice President and Managing Director

For Wacker Neuson

Michael Hanson

Manager, Product Engineering

For Wacker Neuson

Jeff Volden

Director, Product Engineering

For Wacker Neuson

Table of Contents

HI35 – HI90

wc_bo5200024469_04_FM10T

7

Foreword 3

EC Declaration of Conformity 5

1 Safety Information 9

1.1 Signal Words Used in this Manual ....................................................... 9

1.2 Machine Description and Intended Use ............................................. 10

1.3 Safety Guidelines for Operating the Machine ..................................... 11

1.4 Safety Guidelines for Operating Combustion Burners ....................... 13

1.5 Service Safety .................................................................................... 14

1.6 Safety Guidelines for Lifting the Machine ........................................... 15

2 Labels 16

2.1 Label Locations .................................................................................. 16

2.2 Label Meanings .................................................................................. 17

3 Lifting and Transporting 20

3.1 Lifting the Machine ............................................................................. 20

3.2 Transporting the Machine ................................................................... 22

4 Operation 23

4.1 Preparing the Machine for First Use ................................................... 23

4.2 Assembling the Machine .................................................................... 24

4.3 Installing the Front Duct Adapter ........................................................ 25

4.4 Flex Ducting Options .......................................................................... 26

4.5 Ducting Guidelines ............................................................................. 27

4.6 Control and Component Locations ..................................................... 29

4.7 Machine Components Descriptions .................................................... 29

4.8 Positioning the Machine ..................................................................... 30

4.9 Requirements for the Electric Power Source ..................................... 31

4.10 Connecting to the Power Source ........................................................ 32

4.11 Recommended Fuels and Fuel Blending Guide ................................. 33

4.12 Venting the Machine ........................................................................... 34

4.13 Operating Status Indicators ................................................................ 36

4.14 Control Panel ...................................................................................... 37

4.15 Before Starting Checks ...................................................................... 38

4.16 Inspecting the Fuel Hose .................................................................... 38

Table of Contents

HI35 – HI90

8

4.17 Starting the Machine ...........................................................................39

4.18 Starting the Machine in Extremely Cold Weather ................................40

4.19 Stopping ..............................................................................................40

4.20 Installing and Using the Remote Thermostat ......................................41

4.21 Using the Fuel Valve (Bleeding the Fuel System) ...............................42

5 Burner Setup 43

5.1 Factory Settings ..................................................................................43

5.2 Removing the Access Cover ...............................................................43

5.3 Burner Setup .......................................................................................44

5.4 Inspecting and Adjusting the Oil Burner Electrodes ............................46

5.5 Checking and Changing the Burner Nozzle ........................................48

5.6 Checking and Adjusting the Fuel Pressure .........................................49

5.7 Setting the Air Band ............................................................................51

6 Maintenance 52

6.1 Periodic Maintenance Schedule ..........................................................52

6.2 Inspecting the Heat Exchanger ...........................................................53

6.3 Inspecting and Changing the Fuel Heater Filter ..................................56

6.4 Inspecting, Cleaning, and Testing the Cadmium (CAD) Cell ..............57

6.5 Inspecting the Flame Head .................................................................58

6.6 Cleaning and Replacing the Fuel Filter ...............................................59

6.7 Inspecting the Electrical Connections .................................................60

6.8 Long Term Storage .............................................................................60

6.9 Machine Disposal and Decommissioning ............................................61

7 Troubleshooting 62

8 Technical Data 63

8.1 Machine ...............................................................................................63

8.2 Dimensions ..........................................................................................64

9 Schematics 65

9.1 Electrical Schematic—HI35, HI60, HI90 ..............................................65

9.2 Components—HI35, HI60, HI90 ..........................................................66

9.3 Electrical Schematic—HI60HD, HI90HD .............................................67

9.4 Components—HI60HD, HI90HD .........................................................68

HI35 – HI90 Safety Information

wc_si000909gb_FM10.fm 9

1 Safety Information

1.1 Signal Words Used in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE

signal words which must be followed to reduce the possibility of personal injury,

damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a situation

which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

 Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

 To avoid death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

 To avoid possible death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

 To avoid possible minor or moderate injury from this type of hazard, obey all

safety messages that follow this signal word.

Safety Information HI35 – HI90

10 wc_si000909gb_FM10.fm

1.2 Machine Description and Intended Use

Machine

description

The HI Heater is an indirect-fired air heater that operates on diesel fuel. The

machine consists of the following components:

 Stainless steel combustion chamber and heat exchanger

 Blower

 Single-stage burner

 High-temperature shut-down device

 Fuel tank

Fuel is consumed in a closed combustion chamber. Room air or outside air

(depending on the application) is pulled into the machine where it is heated. This

clean, dry, hot air is then blown into the space to be heated by the blower. Access

to the blower assembly is protected by a guard fitted on the air inlet.

Intended use

The HI Heater is intended to provide heat on outdoor or indoor construction sites (if

properly vented) and in other rugged applications.

This machine has been designed and built strictly for the intended use described

above. Using the machine for any other purpose could permanently damage the

machine or seriously injure the operator or other persons on the work site. Machine

damage caused by misuse is not covered under warranty.

Do not use this machine indoors without proper exhaust venting designed for

indoor use which meets all applicable regulations.

This machine has been designed and built in accordance with the latest global

safety standards. It has been carefully engineered to eliminate hazards as far as

practicable and to increase operator safety through protective guards and labeling.

However, some risks may remain even after protective measures have been taken.

They are called residual risks. On this machine, they may include exposure to:

 exhaust emissions

 hot surfaces such as exhaust vents and fuel heater

 fuel and fuel fumes when refueling

 high voltages and arc flash

To protect yourself and others, make sure you thoroughly read and understand the

safety information presented in this manual before operating the machine.

Optional

accessories

Wacker Neuson Corporation offers many optional accessories for the machine.

These accessories include the following:

 Remote thermostat

Contact your Wacker Neuson dealer for more information.

HI35 – HI90 Safety Information

wc_si000909gb_FM10.fm 11

1.3 Safety Guidelines for Operating the Machine

Operator

training

Before operating the machine:

 Read and understand the operating instructions contained in all manuals

delivered with the machine.

 Familiarize yourself with the location and proper use of all controls and safety

devices.

 Contact Wacker Neuson for additional training if necessary.

When operating this machine:

 Do not allow improperly trained people to operate the machine. People

operating the machine must be familiar with the potential risks and hazards

associated with it.

Operator

qualifications

Only trained personnel are permitted to start, operate, and shut down the machine.

They also must meet the following qualifications:

 have received instruction on how to properly use the machine

 are familiar with required safety devices

The machine must not be accessed or operated by:

 children

 people impaired by alcohol or drugs

Application

area

Be aware of the application area.

 Keep unauthorized personnel, children, and pets away from the machine.

 Remain aware of changing positions and the movement of other equipment and

personnel in the application area/job site.

 Identify whether special hazards exist in the application area, such as toxic

gases, or unstable ground conditions, and take appropriate action to eliminate

the special hazards before using the machine.

Be aware of the application area.

 Do not operate the machine in areas that contain flammable objects, fuels, or

products that produce flammable vapors.

Safety

devices,

controls, and

attachments

Only operate the machine when:

 All safety devices and guards are in place and in working order.

 All controls operate correctly.

 The machine is set up correctly according to the instructions in the Operator’s

Manual.

 The machine is clean.

 The machine’s labels are legible.

To ensure safe operation of the machine:

 Do not operate the machine if any safety devices or guards are missing or

inoperative.

 Do not modify or defeat the safety devices.

 Only use accessories or attachments that are approved by Wacker Neuson.

Safety Information HI35 – HI90

12 wc_si000909gb_FM10.fm

Safe

operating

practices

When operating this machine:

 Remain aware of the machine’s moving parts. Keep hands, feet, and loose

clothing away from the machine’s moving parts.

When operating this machine:

 Do not operate a machine in need of repair.

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while operating this

machine:

 Close-fitting work clothes that do not hinder movement

 Safety glasses with side shields

 Hearing protection

 Safety-toed footwear

Work space

Follow the guidelines below when placing the machine in the workspace.

 Position the machine on a firm, noncombustible, level surface.

 Keep the area immediately surrounding and underneath the machine clean,

neat, and free of debris and combustible materials.

 Keep the area above the machine clear of debris that could fall on the machine.

 Do not position electrical cords under the machine or over the top of the

machine.

After Use

1. Turn the machine off and allow it to cool.

2. Disconnect power from the machine.

3. Ensure that the machine will not tip over, roll, slide, or fall when not being

operated.

4. Store the machine properly when it is not being used. The machine should be

stored in a clean, dry location out of the reach of children.

WARNING

Fire hazard. Do not move the machine while it is plugged in, even if power is lost.

 Turn off the machine, wait 10 minutes, disconnect power cord, and let it cool

completely.

HI35 – HI90 Safety Information

wc_si000909gb_FM10.fm 13

1.4 Safety Guidelines for Operating Combustion Burners

When using the machine:

 Clean up any spilled fuel immediately.

 Replace the fuel tank cap after refueling the machine.

 Refill the fuel tank in a well-ventilated area.

When using the machine:

 Do not fill or drain the fuel tank near an open flame, while smoking, or while the

machine is running.

 Do not smoke when refueling the machine.

 Do not use gasoline, crankcase oil, or any oil containing gasoline.

DANGER

Exhaust gas from the burner contains carbon monoxide, a deadly poison. Exposure

to carbon monoxide can kill you in minutes.

 Never run the machine indoors or in an enclosed area unless the machine is

vented properly according to local and national codes.

Safety Information HI35 – HI90

14 wc_si000909gb_FM10.fm

1.5 Service Safety

Service

training

Before servicing or maintaining the machine:

 Read and understand the instructions contained in all manuals delivered with

the machine.

 Familiarize yourself with the location and proper use of all controls and safety

devices.

 Only trained personnel shall troubleshoot or repair problems occurring with the

machine.

 Contact Wacker Neuson for additional training if necessary.

When servicing or maintaining this machine:

 Do not allow improperly trained people to service or maintain the machine.

Personnel servicing or maintaining the machine must be familiar with the

associated potential risks and hazards.

Precautions

Follow the precautions below when servicing or maintaining the machine.

 Read and understand the service procedures before performing any service to

the machine.

 All adjustments and repairs must be completed before operation. Do not

operate the machine with a known problem or deficiency.

 All repairs and adjustments shall be completed by a qualified technician.

 Turn off the machine before performing maintenance or making repairs.

Machine

modifications

When servicing or maintaining the machine:

 Use only accessories/attachments that are approved by Wacker Neuson.

When servicing or maintaining the machine:

 Do not defeat safety devices.

 Do not modify the machine without the express written approval of Wacker

Neuson.

Replacing

parts and

labels

 Replace worn or damaged components.

 Replace all missing and hard-to-read labels.

 When replacing electrical components, use components that are identical in

rating and performance to the original components.

 When replacement parts are required for this machine, use only Wacker

Neuson replacement parts or those parts equivalent to the original in all types of

specifications, such as physical dimensions, type, strength, and material.

Cleaning

When cleaning and servicing the machine:

 Keep the machine clean and free of debris such as leaves, paper, cartons, etc.

 Keep the labels legible.

When cleaning the machine:

 Do not clean the machine while it is running.

 Never use gasoline or other types of fuels or flammable solvents to clean the

machine. Fumes from fuels and solvents can become explosive.

HI35 – HI90 Safety Information

wc_si000909gb_FM10.fm 15

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while servicing or

maintaining this machine:

 Close-fitting work clothes that do not hinder movement

 Safety glasses with side shields

 Hearing protection

 Safety-toed footwear

In addition, before servicing or maintaining the machine:

 Tie back long hair.

 Remove all jewelry (including rings).

1.6 Safety Guidelines for Lifting the Machine

When lifting the machine:

 Make sure slings, chains, hooks, ramps, jacks, forklifts, cranes, hoists, and any

other type of lifting device used is attached securely and has enough weight-

bearing capacity to lift or hold the machine safely. See section Technical Data

for machine weight.

 Remain aware of the location of other people when lifting the machine.

 Only use the lifting points and tie-downs described in the Operator’s Manual.

 Make sure the transporting vehicle has sufficient load capacity and platform size

to safely transport the machine.

To reduce the possibility of injury:

 Do not stand under the machine while it is being lifted or moved.

 Do not get onto the machine while it is being lifted or moved.

wc_si000914gb_FM10.fm

16

Labels HI35 – HI90

2 Labels

2.1 Label Locations

wc_gr012461

HI 35

A

B

C

D

E

F

G

H

G

wc_gr012462

A

B

C

D

E

F

G

H

J

G

H

A

HI 60 / HI 60HD / HI 90 / HI 90HD

wc_si000914gb_FM10.fm

17

HI35 – HI90 Labels

2.2 Label Meanings

1

A WARNING

Hot surface

B WARNING

Electric shock hazard.

Disconnect power before servicing.

Read Operator’s Manual.

C CAUTION

This machine uses diesel fuel.

D DANGER

Asphyxiation hazard. Heater exhaust contains

carbon monoxide. This is a poison you cannot

see or smell.

Do not operate this machine indoors or in an

enclosed area unless the machine is vented

properly according to local and national codes.

Read the Operator’s Manual.

5200020709

181146

181145181145

52000221745200022174

wc_si000914gb_FM10.fm

18

Labels HI35 – HI90

E WARNING

 Read and understand the supplied Operator's

Manual before operating this machine.

 The requirements of local authorities having

jurisdiction shall be followed.

 Do not use heater in close proximity of

combustible surfaces or materials.

 Ensure fresh air supply to space where heater

is used.

 Equipment must be grounded.

 Use only light diesel oil No. 2 or kerosene.

 Do not use gasoline or crankcase drain oil.

 Do not fill the tank while the unit is operating.

 Never disconnect the power source while

heater is running.

 Do not start the heater when the combustion

chamber is hot.

 Do not start the heater when excess oil has

accumulated in the chamber.

 Allow unit to cool before shutdown. Stop heater

only at control panel switch in order to ensure

automatic cooling off. Heater will stop by itself

after automatic cooling off.

 Clean fuel filter regularly and drain water from

fuel tank if necessary.

 When heater is first used after a long storage

period it might be necessary to reset the

machine up to three times by the reset button.

The button will light up; wait two minutes before

resetting.

 Do not tamper with the unit. Have a competent

service technician make any adjustments.

 Unplug machine before removing the cover for

any maintenance.

F WARNING

Cutting hazard. Keep hands and feet away from

moving blade.

52000218845200021884

wc_si000914gb_FM10.fm

19

HI35 – HI90 Labels

G NOTICE

Lifting point

H Tie-down point.

J Read the Operator’s Manual.

Setting the valve to this position (down) directs

the fuel back to the tank.

Setting the valve to this position (up) directs the

fuel to the burner.

Lifting and Transporting HI35 – HI90

20 wc_tx003883gb_FM10.fm

3 Lifting and Transporting

3.1 Lifting the Machine

Requirements

 Lifting equipment (crane, hoist, or fork lift truck) capable of supporting the

machine’s weight. See Chapter Technical Data.

 Lifting devices (hooks, chains, and shackles) capable of supporting the

machine’s weight

 Machine stopped

 All venting removed from the heater (if equipped)

NOTICES  Do not tow this machine.

 Do not route tie-down straps or chains over the top of the machine.

 Fuel may leak from the fuel tank cap during lifting. Before lifting, remove fuel

from the machine, if necessary. Clean up any leaked fuel before using the

machine.

Procedure

Perform the procedure below to lift the machine.

1. Turn off the machine and let the machine cool completely.

2. Disconnect the power cord.

3. Cover all openings on the machine to avoid infiltration from road debris and

dust.

This procedure continues on the next page.

WARNING

Crushing hazard.

 Only qualified riggers should attempt aerial lifting of this machine.

WARNING

Crushing hazard. You may be crushed if the lifting devices fail.

 Never stand under, or get onto, the machine while it is being lifted or moved.

Page is loading ...

Wacker Neuson HI35 User manual

This manual is also suitable for

Wacker Neuson HI35 User manual

Related papers

Other documents