Wacker Neuson SE75 User manual

Truss Screed

SP /...

HP /...

HPG /...

OPERATOR’S MANUAL

0155950en 002

0403

0155950EN

SP/HP/HPG /... Table of Contents

wc_bo0155950001enTOC.fm 1

1. Foreword 3

2. Safety Information 4

2.1 Operating Safety .................................................................................. 5

2.2 Operator Safety while using Internal Combustion Engines .................. 6

2.3 Service Safety ...................................................................................... 7

2.4 Label Locations .................................................................................... 8

2.5 Safety Labels ........................................................................................ 9

2.6 Information Labels ............................................................................. 10

3. Technical Data 11

3.1 Engine ................................................................................................ 11

3.2 SP 50 /... ............................................................................................. 11

3.3 HP 50 /... ............................................................................................ 12

3.4 HPG 50 /... .......................................................................................... 12

3.5 SP 75 /... ............................................................................................. 12

3.6 HP 100 /... .......................................................................................... 12

3.7 HPG 100 /... ........................................................................................ 13

3.8 Sound Measurements ........................................................................ 13

3.9 Vibration Measurements .................................................................... 13

4. Operation 14

4.1 Application .......................................................................................... 14

4.2 Recommended Fuel ........................................................................... 14

4.3 New Machine Set-up .......................................................................... 14

4.4 Freewheeling the Crank ..................................................................... 17

4.5 Installing Screed Sections .................................................................. 18

4.6 Aligning the Screed ............................................................................ 19

4.7 Winch and Cable ................................................................................ 21

4.8 Before Starting ................................................................................... 22

4.9 To Start ............................................................................................... 23

4.10 To Stop ............................................................................................... 23

4.11 Operation ............................................................................................ 24

Table of Contents SP/HP/HPG /...

wc_bo0155950001enTOC.fm 2

5. Maintenance 25

5.1 Periodic Maintenance Schedule ..........................................................25

5.2 Engine Oil ............................................................................................25

5.3 Air Cleaner ..........................................................................................26

5.4 Sediment Cup ......................................................................................27

5.5 Adjusting Engine Speed ......................................................................27

5.6 Carburetor Adjustment ........................................................................28

5.7 Spark Plug ...........................................................................................29

5.8 Cleaning the Screed ............................................................................30

5.9 Storage ................................................................................................30

5.10 Transporting ........................................................................................31

5.11 Troubleshooting ...................................................................................31

6. Accessories 32

6.1 Recessing Attachment ........................................................................32

6.2 Outrigger Attachment ..........................................................................33

6.3 Wall Slider Attachment ........................................................................34

Foreword

wc_tx000001gb.fm 3

CALIFORNIA

Proposition 65 Warning:

Engine exhaust, some of its constituents, and certain vehicle

components contain or emit chemicals known to the State of California

to cause cancer and birth defects or other reproductive harm.

1. Foreword

This manual provides information and procedures to safely operate

and maintain this Wacker model. For your own safety and protection

from injury, carefully read, understand and observe the safety

instructions described in this manual.

Keep this manual or a copy of it with the machine. If you lose this

manual or need an additional copy, please contact Wacker

Corporation. This machine is built with user safety in mind; however,

it can present hazards if improperly operated and serviced. Follow

operating instructions carefully! If you have questions about operating

or servicing this equipment, please contact Wacker Corporation.

The information contained in this manual was based on machines in

production at the time of publication. Wacker Corporation reserves the

right to change any portion of this information without notice.

All rights, especially copying and distribution rights are reserved.

No part of this publication may be reproduced in any form or by any

means, electronic or mechanical, including photocopying, without

express written permission from Wacker Corporation.

Any type of reproduction or distribution not authorized by Wacker

Corporation represents an infringement of valid copyrights and will be

prosecuted. We expressly reserve the right to make technical

modifications, even without due notice, which aim at improving our

machines or their safety standards.

WARNING

Safety Information SP/HP/HPG /...

wc_si000033gb.fm 4

2. Safety Information

This manual contains DANGER, WARNING, CAUTION, and NOTE

callouts which must be followed to reduce the possibility of personal

injury, damage to the equipment, or improper service.

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that follow this

symbol to avoid possible injury or death.

DANGER indicates an imminently hazardous situation which, if not

avoided, will result in death or serious injury.

WARNING indicates a potentially hazardous situation which, if not

avoided, could result in death or serious injury.

CAUTION indicates a potentially hazardous situation which, if not

avoided, may result in minor or moderate injury.

CAUTION: Used without the safety alert symbol, CAUTION indicates

a potentially hazardous situation which, if not avoided, may result in

property damage.

Note: Contains additional information important to a procedure.

DANGER

WARNING

CAUTION

SP/HP/HPG /... Safety Information

wc_si000033gb.fm 5

2.1 Operating Safety

Notice: State Health Safety Codes and Public Resources Codes

specify that in certain locations spark arresters be used on internal

combustion engines that use hydrocarbon fuels. A spark arrester is a

device designed to prevent accidental discharge of sparks or flames

from the engine exhaust. Spark arresters are qualified and rated by

the United States Forest Service for this purpose.

In order to comply with local laws regarding spark arresters, consult

the engine distributor or the local Health and Safety Administrator.

Familiarity and proper training are required for the safe operation of

equipment! Equipment operated improperly or by untrained personnel

can be dangerous! Read the operating instructions contained in both

this manual and the engine manual and familiarize yourself with the

location and proper use of all controls. Inexperienced operators should

receive instruction from someone familiar with the equipment before

being allowed to operate the machine.

2.1.1 NEVER touch the engine or muffler while the engine is on or

immediately after it has been turned off. These areas get hot and may

cause burns.

2.1.2 NEVER use accessories or attachments that are not recommended by

Wacker. Damage to equipment and injury to the user may result.

2.1.3 NEVER leave machine running unattended.

2.1.4 NEVER operate the machine with the belt guard missing. Exposed

drive belt and pulleys create potentially dangerous hazards that can

cause serious injuries.

2.1.5 NEVER run machine indoors or in an enclosed area unless adequate

ventilation, through such items as exhaust fans or hoses, is provided.

Exhaust gas from the engine contains poisonous carbon monoxide

gas; exposure to carbon monoxide can cause loss of consciousness

and may lead to death.

2.1.6 ALWAYS wear protective clothing appropriate to the job site when

operating equipment.

2.1.7 ALWAYS wear hearing protection when operating equipment.

2.1.8 ALWAYS wear protective clothing appropriate to the job site when

operating equipment.

2.1.9 ALWAYS read, understand, and follow procedures in Operator's

Manual before attempting to operate equipment.

2.1.10 ALWAYS check that all controls are functioning properly immediately

after start-up! DO NOT operate machine unless all controls operate

correctly.

WARNING

Safety Information SP/HP/HPG /...

wc_si000033gb.fm 6

2.1.11 ALWAYS close fuel valve on engines equipped with one when

machine is not being operated.

2.1.12 ALWAYS store equipment properly when it is not being used.

Equipment should be stored in a clean, dry location out of the reach of

children.

2.1.13 ALWAYS operate machine with all safety devices and guards in place

and in working order.

2.1.14 ALWAYS operate screed along even forms. Avoid objects protruding

from concrete such as stakes or plumbing that would interfere with

screed operation.

2.2 Operator Safety while using Internal Combustion Engines

Internal combustion engines present special hazards during operation

and fueling! Read and follow warning instructions in engine owner's

manual and safety guidelines below. Failure to follow warnings and

safety guidelines could result in severe injury or death.

2.2.1 DO NOT smoke while operating machine.

2.2.2 DO NOT smoke when refueling engine.

2.2.3 DO NOT refuel hot or running engine.

2.2.4 DO NOT refuel engine near open flame.

2.2.5 DO NOT run engine near open flames.

2.2.6 ALWAYS refill fuel tank in well-ventilated area.

2.2.7 ALWAYS replace fuel tank cap after refueling.

DANGER

SP/HP/HPG /... Safety Information

wc_si000033gb.fm 7

2.3 Service Safety

Poorly maintained equipment can become a safety hazard! In order

for the equipment to operate safely and properly over a long period of

time, periodic maintenance and occasional repairs are necessary.

2.3.1 DO NOT attempt to clean or service machine while it is running.

Rotating parts can cause severe injury.

2.3.2 DO NOT crank a flooded engine with the spark plug removed on

gasoline-powered engines. Fuel trapped in the cylinder will squirt out

the spark plug opening.

2.3.3 DO NOT test for spark on gasoline-powered engines, if engine is

flooded or the smell of gasoline is present. A stray spark could ignite

fumes.

2.3.4 DO NOT use gasoline or other types of fuels or flammable solvents to

clean parts, especially in enclosed areas. Fumes from fuels and

solvents can become explosive.

2.3.5 ALWAYS keep area around muffler free of debris such as leaves,

paper, cartons, etc. A hot muffler could ignite them, starting a fire.

2.3.6 ALWAYS replace worn or damaged components with spare parts

designed and recommended by Wacker.

2.3.7 ALWAYS disconnect spark plug on machines equipped with gasoline

engines, before servicing, to avoid accidental start-up.

2.3.8 ALWAYS keep machine clean and labels legible. Replace all missing

and hard-to-read labels. Labels provide important operating

instructions and warn of dangers and hazards.

2.3.9 ALWAYS handle cables carefully. The cables can fray and develop

sharp edges which can cause serious cuts.

WARNING

Safety Information SP/HP/HPG /...

wc_si000033gb.fm 8

2.4 Label Locations

SP/HP/HPG /... Safety Information

wc_si000033gb.fm 9

2.5 Safety Labels

Wacker machines use international pictorial labels where needed.

These labels are described below:

Label Meaning

DANGER!

Engines emit carbon monoxide; operate only

in well ventilated area. Read the operator's

manual.

No sparks, flames or burning objects near

machine. Shut off engine before refueling.

WARNING!

Hot surface.

WARNING!

To prevent hearing loss, wear hearing protec-

tion when operating this machine.

Read and understand the supplied operator's

manual before operating this machine. Failure

to do so increases the risk of injury to yourself

or others.

CAUTION!

Wear foot protection around moving parts.

WARNING!

Hand injury if caught in moving belt.

Always replace belt guard.

Safety Information SP/HP/HPG /...

wc_si000033gb.fm 10

2.6 Information Labels

Label Meaning

A nameplate listing the Model Number, Item

Number, Revision, and Serial Number is attached

to each unit. Please record the information found

on this plate so it will be available should the

nameplate become lost or damaged. When

ordering parts or requesting service information,

you will always be asked to specify the model,

item number, revision number, and serial number

of the unit.

This machine may be covered by one or more

patents.

SP/HP/HPG /... Technical Data

wc_td000031gb.fm 11

3. Technical Data

3.1 Engine

3.2 SP 50 /...

Part No. SP 50 /...

0008295

0008296

0009163

0009164

HP /...

0008291

0008292

0009159

0009160

HPG /...

0008293

0008294

0009161

0009162

Machine

Engine Type

4-stroke, overhead valve, single cylinder

Engine Make

Honda

Engine Model

GX 160 K1 QWX2 GX 240 K1 QA,B

Rated Power

kW (Hp) 5.5 (4.1) 5.9 (8)

Displacement

cm³ (in³) 163 (9.9) 242 (14.8)

Spark Plug

(NGK) BPR 6ES

Electrode Gap

mm (in) 0.028–0.031 (0.7–0.8)

Engine Speed - full load

rpm 3600

Engine Speed - idle

rpm 3700 ±100

Air Cleaner

type Dual Element

Engine Lubrication

oil grade SAE 10W30

Service Class SF, SE, SD, or SC

Engine Oil Capacity

l (oz.) 0.6 (30) 1.1 (37)

Fuel

type Regular Unleaded Gasoline

Fuel Tank Capacity

l (qts.) 3.8 (4.0) 6.1 (6.4)

Part No. SP 50

0008296

SP 50 CE

0009164

Machine

Dimensions - Truss

1.5m (5.0 ft) x 275mm (11 in) x 355mm (14 in)

Dimensions - Machine

mm (in) 1851 (73) x 355 (14) x 876 (35)

Weight

kg (lbs) 50 (110)

Technical Data SP/HP/HPG /...

wc_td000031gb.fm 12

3.3 HP 50 /...

3.4 HPG 50 /...

3.5 SP 75 /...

3.6 HP 100 /...

Part No. HP 50

0008292

HP 50 CE

0009160

Machine

Dimensions - Truss

1.5m (5.0 ft) x 355mm (14 in) x 475mm (19 in)

Dimensions - Machine

mm (in) 1740 (69) x 664 (26) x 889 (35)

Weight

kg (lbs) 55 (123)

Part No. HPG 50

0008294

HPG 50 CE

0009162

Machine

Dimensions - Truss

1.5m (5.0 ft) x 355mm (14 in) x 475mm (19 in)

Dimensions - Machine

mm (in) 1740 (69) x 664 (26) x 889 (35)

Weight

kg (lbs) 66 (147)

Part No. SP 75

0008295

SP 75 CE

0009163

Machine

Dimensions - Truss

2.3m (7.5 ft) x 275mm (11 in) x 355mm (14 in)

Dimensions - Machine

mm (in) 2613 (103) x 680 (27) x 889 (35)

Weight

kg (lbs) 60 (134)

Part No. HP 100

0008291

HP 100 CE

0009159

Machine

Dimensions - Truss

3.1m (10.0 ft) x 355mm (14 in) x 475mm (19 in)

Dimensions - Machine

mm (in) 3264 (129) x 664 (27) x 889 (35)

Weight

kg (lbs) 81 (180)

SP/HP/HPG /... Technical Data

wc_td000031gb.fm 13

3.7 HPG 100 /...

3.8 Sound Measurements

The required sound specification, per paragraph 1.74.f of 89/392/EEC

machinery directive, is:

• the sound pressure level at operator's location (L

) = 89 dB(A).

• the guaranteed sound power level (L

) = 97 dB(A).

These sound values were determined according to ISO 3744 for the

sound power level (L

) and ISO 6081 for the sound pressure level

) at the operator's location.

3.9 Vibration Measurements

The operating hand/arm vibration level, measured per the

requirements of enclosure 1, Paragraph 2.2 or 3.6.3 of the EC-

Machine Regulations, is approximately 11.8 m/s

The weighted effective acceleration value was determined according

to ISO 8662 Part 1.

The sound and vibration measurements were obtained with the

machine operating on sand at nominal engine speed.

Part No. HPG 100

0008293

HPG 100 CE

0009161

Machine

Dimensions - Truss

3.1m (10.0 ft) x 355mm (14 in) x 475mm (19 in)

Dimensions - Machine

mm (in) 3264 (129) x 667 (27) x 889 (35)

Weight

kg (lbs) 92 (204)

Operation SP/HP/HPG /...

wc_tx000018gb.fm 14

4. Operation

4.1 Application

This screed is a modern, high production machine intended to provide

consolidation of concrete while striking off and closing concrete

surfaces. The vibratory motion, consolidation, and closing action are

controlled by the engine speed. Wacker screeds are easily put

together to form desired lengths for all finishing applications. Finishing

rates will depend on operator skill and job conditions.

DO NOT use this machine for any application other than screeding

concrete.

4.2 Recommended Fuel

The engine requires regular grade unleaded gasoline. Use only fresh,

clean gasoline. Gasoline containing water or dirt will damage fuel

system. Consult engine owner’s manual for complete fuel

specifications.

4.3 New Machine Set-up

See Graphic: wc_gr000342

Screeds are shipped from the factory with the engine, beltguard, and

end winch section removed. These components need to be

assembled prior to use.

Screeds are shipped from the factory in various sections and lengths.

Sections need to be assembled and aligned prior to use. Follow

Installing Screed Sections and Aligning the Screed when setting up

new machines or when installing new sections.

SP/HP/HPG /... Operation

wc_tx000018gb.fm 15

Operation SP/HP/HPG /...

wc_tx000018gb.fm 16

To assemble the engine:

4.3.1 Mount engine bracket (a) to the right side of the screed. There are two

vacant holes (approx. 6th or 7th hole from end) to mount the bracket

using hardware (*) and mounting plate (b) provided.

4.3.2 Mount engine (c) to bracket using hardware (*) provided. Do not

tighten, engine must be moved to adjust belt tension.

4.3.3 Mount back plate (d) to engine bracket (a) using hardware (*) provided.

Mount clutch (e) to engine. Loop belt (f) around clutch (e).

4.3.4 Slide engine back on slots to create tension on the belt. Adjust belt for

1/2"–5/8" deflection midway between clutch and pulley. Tighten

engine mounting hardware.

4.3.5 Mount back plate (d) to lower beltguard (g) using hardware (*)

provided. Mount belt guard bracket (h) to back plate (d) and lower

beltguard (g) using hardware (*) provided.

4.3.6 Mount upper beltguard (j) to back plate (d) using hardware (*)

provided.

To assemble the end winch section:

4.3.1 Mount upright section (k) to two end holes of the lower screed frame

(m) and end hole of upper frame support (n) using hardware (*)

provided.

4.3.2 Mount winch assemblies (o) to top of end section using hardware (*)

provided.

Note: Configure winch assemblies as shown for proper cable

alignment.

* For specific hardware sizes and quantities, refer to Instruction Sheet

P/N 0151589.

SP/HP/HPG /... Operation

wc_tx000018gb.fm 17

4.4 Freewheeling the Crank

See Graphic: wc_gr000072

To make it easier when routing cables through guides or extending

across forms, freewheeling the crank is an option. To do this:

4.4.1 Give a hard counterclockwise turn to the crank handle (a) and continue

until handle unthreads from winch spool assembly (b).

4.4.2 Cable is now able to be pulled freely to desired length.

4.4.3 Replace crank handle before operating screed.

Operation SP/HP/HPG /...

wc_tx000018gb.fm 18

4.5 Installing Screed Sections

See Graphic: wc_g000344

Wacker screed sections are connected in two places: at the top with T-

bolts (a) and at the bottom with a connector plate (b).

Each screed section has a coarse and a fine side, determined by the

top tube T-bolt connector threads. These T-bolts are critical to

alignment of the screed, so it is important to insure the integrity of the

threads.

The connector plate permanently mounts to the coarse end of the

screed section. It is secured to the section with shoulder bolts (c), lock

nuts (d) and lock washers (e). The connector plate also carries a

flange bearing (f) that guides and aligns the eccentric shaft (g).

Note: Remember to always leave the connector plate attached to the

coarse section end and disconnect from the fine side.

For initial setup:

4.5.1 Lay the sections of screed on a flat surface and install the connector

plate (b) to the coarse side.

4.5.2 Align the back T-blades and slide the two sections together while

guiding the eccentric shaft (g) into the mating surface of the flange

bearing (f).

Note: While assembling the sections, make sure that the T-bolts are

threaded into the top tube so they don’t make contact with each other

and impede the alignment of the connector plate.

Once the sections are in place, you may proceed with loosly bolting the

connector plate to the fine side of the screed. A tapered pin punch (h)

inserted through the bolt holes will aid in the alignment of the bracket.

Repeat this until all remaining mounting hardware is in place.

At this time, the T-bolts can be adjusted so that they are at an equal

distance between the assembled sections (i). Install the connecting

hardware (k) and tighten. Leave the jam nuts (m) loose for the next

step which is truing the screed.

Note: Once T-bolts have been adjusted at an equal distance, tighten

all hardware making sure screed sections stay level.

Page is loading ...

Wacker Neuson SE75 User manual

Related papers

Other documents