Makita LS1017L Owner's manual

GB Slide Compound Miter Saw Instruction manual

F Scie à Onglet Radiale Manuel d’instructions

D Kapp- und Gehrungssäge Betriebsanleitung

I Troncatrice radiale per legno Istruzioni per l’uso

NL Schuifbare samengesteld- Gebruiksaanwijzing

verstekzaag

E Sierra de Inglete Telescópica Manual de instrucciones

P Serra de Esquadria c/Braço Manual de instruções

Telescópico

DK Afkorter- og geringssav Brugsanvisning

GR Συρόμενο σύνθετο φαλτσοπρίονο Οδηγίες χρήσης

LS1017

LS1017L

Page is loading ...

10

ENGLISH

Contents

SPECIFICATIONS......................................................... 11

ADDITIONAL SAFETY RULES FOR TOOL.................. 12

INSTALLATION ............................................................. 13

FUNCTIONAL DESCRIPTION ...................................... 13

ASSEMBLY ................................................................... 15

OPERATION.................................................................. 17

MAINTENANCE............................................................. 19

ACCESSORIES............................................................. 20

FRANÇAIS

Table des matières

SPÉCIFICATIONS......................................................... 22

CONSIGNES DE SÉCURITÉ ADDITIONNELLES

POUR L’OUTIL .............................................................. 23

INSTALLATION ............................................................. 24

DESCRIPTION DU FONCTIONNEMENT ..................... 24

ASSEMBLAGE .............................................................. 27

FONCTIONNEMENT..................................................... 29

ENTRETIEN .................................................................. 32

ACCESSOIRES............................................................. 33

DEUTSCH

Inhalt

TECHNISCHE DATEN .................................................. 34

ZUSÄTZLICHE SICHERHEITSREGELN FÜR DAS

WERKZEUG .................................................................. 35

INSTALLATION ............................................................. 36

FUNKTIONSBESCHREIBUNG ..................................... 36

MONTAGE..................................................................... 39

BETRIEB ....................................................................... 41

WARTUNG .................................................................... 44

ZUBEHÖR ..................................................................... 45

ITALIANO

Sommario

CARATTERISTICHE TECNICHE.................................. 47

REGOLE DI SICUREZZA AGGIUNTIVE PER

L’UTENSILE .................................................................. 48

INSTALLAZIONE........................................................... 49

DESCRIZIONE FUNZIONALE ...................................... 49

MONTAGGIO ................................................................ 52

USO ............................................................................... 54

MANUTENZIONE .......................................................... 56

ACCESSORI.................................................................. 57

NEDERLANDS

Inhoud

TECHNISCHE GEGEVENS .......................................... 59

AANVULLENDE VEILIGHEIDSVOORSCHRIFTEN

VOOR GEREEDSCHAP................................................ 60

VOORBEREIDINGEN ................................................... 61

BESCHRIJVING VAN DE FUNCTIES........................... 61

ONDERDELEN AANBRENGEN/VERWIJDEREN ........ 64

GEBRUIK....................................................................... 66

ONDERHOUD ............................................................... 69

ACCESSOIRES............................................................. 70

ESPAÑOL

Contenido

ESPECIFICACIONES ....................................................71

NORMAS DE SEGURIDAD ADICIONALES PARA LA

HERRAMIENTA .............................................................72

INSTALACIÓN ...............................................................73

DESCRIPCIÓN DEL FUNCIONAMIENTO ....................73

MONTAJE ......................................................................76

OPERACIÓN..................................................................78

MANTENIMIENTO .........................................................81

ACCESORIOS ...............................................................81

PORTUGUÊS

Índice

ESPECIFICAÇÕES........................................................83

REGRAS ADICIONAIS DE SEGURANÇA

PARA A FERRAMENTA ................................................84

INSTALAÇÃO ................................................................85

DESCRIÇÃO DO FUNCIONAMENTO...........................85

MONTAGEM ..................................................................88

FUNCIONAMENTO .......................................................90

MANUTENÇÃO..............................................................92

ACESSÓRIOS ...............................................................93

DANSK

Indhold

SPECIFIKATIONER.......................................................95

YDERLIGERE SIKKERHEDSREGLER FOR

MASKINEN ....................................................................96

MONTERING .................................................................97

FUNKTIONSBESKRIVELSE..........................................97

MONTERING .................................................................99

BETJENING .................................................................101

VEDLIGEHOLDELSE ..................................................104

TILBEHØR ...................................................................104

ΕΛΛΗΝΙΚΑ

Περιεχόμενα

ΠΡΟΔΙΑΓΡΑΦΕΣ .........................................................106

ΠΡΟΣΘΕΤΟΙ ΚΑΝΟΝΕΣ ΑΣΦΑΛΕΙΑΣ ΓΙΑ ΤΟ

ΕΡΓΑΛΕΙΟ ...................................................................107

ΤΟΠΟΘΕΤΗΣΗ ............................................................108

ΠΕΡΙΓΡΑΦΗ ΛΕΙΤΟΥΡΓΙΑΣ

........................................108

ΣΥΝΑΡΜΟΛΟΓΗΣΗ.....................................................111

ΛΕΙΤΟΥΡΓΙΑ ................................................................113

ΣΥΝΤΗΡΗΣΗ ...............................................................116

ΑΞΕΣΟΥΑΡ..................................................................117

11

ENGLISH (Original instructions)

Explanation of general view

SPECIFICATIONS

Model LS1017/LS1017L

Blade diameter 255 mm - 260 mm

Hole diameter

For all countries other than European countries 25.4 mm

For European countries 30 mm

Max. Cutting capacities (H x W) with 260 mm in diameter

No load speed (min

-1

) 4,200

Laser Type (LS1017L only) Red Laser 650 nm, <1 mW (Laser Class 2)

Dimensions (L x W x H) 825 mm x 536 mm x 581 mm

Net weight For all countries other than European countries............19.4 kg

For European countries............19.5 kg

Safety class /II

• Due to our continuing programme of research and development, the specifications herein are subject to change without

notice.

• Specifications may differ from country to country.

• Weight according to EPTA-Procedure 01/2003

1. Stopper pin

2. Bolts

3. Blade guard

4. Kerf board

5. Screw

6. Saw blade

7. Blade teeth

8. Left bevel cut

9. Straight cut

10. Adjusting bolt

11. Turn base

12. Top surface of turn base

13. Periphery of blade

14. Guide fence

15. Stopper arm

16. Adjusting screw

17. Miter scale

18. Pointer

19. Lock lever

20. Grip

21. Lever

22. Arm

23. Bevel scale

24. Release button

25. Locking screw

26. Lock-off button

27. Switch trigger

28. Hole for padlock

29. Switch for laser

30. Screw holding the laser unit box

31. Dry cell

32. Socket wrench with hex wrench

on its other end

33. Wrench holder

34. Socket wrench

35. Blade case

36. Center cover

37. Hex bolt

38. Arrow

39. Shaft lock

40. Hex bolt (left-handed)

41. Outer flange

42. Ring

43. Inner flange

44. Spindle

45. Dust nozzle

46. Dust bag

47. Fastener

48. Support

49. Sliding fence

50. Clamping screw

51. Vise arm

52. Vise knob

53. Vise rod

54. Vise plate

55. Vise nut

56. Holder

57. Lock screw

58. 52/38° type crown molding

59. 45° type crown molding

60. 45° type cove molding

61. Inside corner

62. Outside corner

63. Vise

64. Spacer block

65. Aluminum extrusion

66. Horizontal vise (optional

accessory)

67. Holes

68. Cut grooves with blade

69. Hex bolts

70. Triangular rule

71. 0° adjusting bolt

72. Left 45° bevel angle adjusting bolt

73. Right 5° bevel angle adjusting bolt

74. Screwdriver

75. Brush holder cap

Miter angle

Bevel angle

45° (left) 0°

0° 50 mm x 310 mm 91 mm x 310 mm

45° 50 mm x 220 mm 91 mm x 220 mm

60° (right) - 91 mm x 153 mm

12

Symbols END223-1

The following show the symbols used for the equipment.

Be sure that you understand their meaning before use.

............. Read instruction manual.

............. DOUBLE INSULATION

......... To avoid injury from flying debris, keep

holding the saw head down, after making

cuts, until the blade has come to a

complete stop.

When performing slide cut, first pull

carriage fully and press down handle,

then push carriage toward the guide

fence.

............. Do not place hand or fingers close to the

blade.

.......... Adjust sliding fences clear of blade and

blade guard properly.

...... Never look into the laser beam. Direct

laser beam may injure your eyes.

Intended use

ENE006-1

The tool is intended for accurate straight and miter cutting

in wood. With appropriate saw blades, aluminum can also

be sawed.

Power supply

ENF002-1

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

General Power Tool Safety

Warnings GEA010-1

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

serious injury.

Save all warnings and

instructions for future reference.

ADDITIONAL SAFETY RULES

FOR TOOL

ENB034-6

1. Wear eye protection.

2. Keep hands out of path of saw blade. Avoid

contact with any coasting blade. It can still cause

severe injury.

3. Do not operate saw without guards in place.

Check blade guard for proper closing before each

use. Do not operate saw if blade guard does not

move freely and close instantly. Never clamp or tie

the blade guard into the open position.

4. Do not perform any operation freehand. The

workpiece must be secured firmly against the turn

base and guide fence with the vise during all

operations. Never use your hand to secure the

workpiece.

5. Never reach around saw blade.

6. Turn off tool and wait for saw blade to stop before

moving workpiece or changing settings.

7. Unplug tool before changing blade or servicing.

8. Always secure all moving portions before carrying

the tool.

9. Stopper pin which locks the cutter head down is

for carrying and storage purposes only and not for

any cutting operations.

10. Do not use the tool in the presence of flammable

liquids or gases. The electrical operation of the tool

could create an explosion and fire when exposed to

flammable liquids or gases.

11. Check the blade carefully for cracks or damage

before operation.

Replace cracked or damaged blade immediately.

12. Use only flanges specified for this tool.

13. Be careful not to damage the arbor, flanges

(especially the installing surface) or bolt. Damage

to these parts could result in blade breakage.

14. Make sure that the turn base is properly secured

so it will not move during operation.

15. For your safety, remove the chips, small pieces,

etc. from the table top before operation.

16. Avoid cutting nails. Inspect for and remove all

nails from the workpiece before operation.

17. Make sure the shaft lock is released before the

switch is turned on.

18. Be sure that the blade does not contact the turn

base in the lowest position.

19. Hold the handle firmly. Be aware that the saw

moves up or down slightly during start-up and

stopping.

20. Make sure the blade is not contacting the

workpiece before the switch is turned on.

21. Before using the tool on an actual workpiece, let it

run for a while. Watch for vibration or wobbling

that could indicate poor installation or a poorly

balanced blade.

22. Wait until the blade attains full speed before

cutting.

23. Stop operation immediately if you notice anything

abnormal.

24. Do not attempt to lock the trigger in the on

position.

25. Be alert at all times, especially during repetitive,

monotonous operations. Do not be lulled into a

false sense of security. Blades are extremely

unforgiving.

26. Always use accessories recommended in this

manual. Use of improper accessories such as

abrasive wheels may cause an injury.

27. Do not use the saw to cut other than wood,

aluminum or similar materials.

28. Connect miter saws to a dust collecting device

when sawing.

13

29. Select saw blades in relation to the material to be

cut.

30. Take care when slotting.

31. Replace the kerf board when worn.

32. Do not use saw blades manufactured from high

speed steel.

33. Some dust created from operation contains

chemicals known to cause cancer, birth defects or

other reproductive harm. Some examples of these

chemicals are:

• lead from lead-based-painted material and,

• arsenic and chromium from chemically-treated

lumber.

Your risk from these exposures varies,

depending on how often you do this type of

work. To reduce your exposure to these

chemicals: work in a well ventilated area and

work with approved safety equipment, such as

those dust masks that are specially designed to

filter out microscopic particles.

34. To reduce the emitted noise, always be sure that

the blade is sharp and clean.

35. The operator is adequately trained in the use,

adjustment and operation of the machine.

36. Use correctly sharpened saw blades. Observe the

maximum speed marked on the saw blade.

37. Refrain from removing any cut-offs or other parts

of the workpiece from the cutting area whilst the

tool is running and the saw head is not in the rest

position.

38. Use only saw blades recommended by the

manufacturer which conform to EN847-1.

39. Wear gloves for handling saw blade (saw blades

shall be carried in a holder wherever practicable)

and rough material.

40. When fitted with laser, no exchange with different

type of laser is permitted. Repairs shall only be

carried out correctly.

SAVE THESE INSTRUCTIONS.

INSTALLATION

Bench mounting (Fig. 1)

When the tool is shipped, the handle is locked in the

lowered position by the stopper pin. Release the stopper

pin by simultaneously applying a slight downward

pressure on the handle and pulling the stopper pin.

WARNING:

• Ensure that the tool will not move on the

supporting surface. Movement of the miter saw on

the supporting surface while cutting may result in loss

of control and serious personal injury. (Fig. 2)

This tool should be bolted with four bolts to a level and

stable surface using the bolt holes provided in the tool’s

base. This will help prevent tipping and possible injury.

FUNCTIONAL DESCRIPTION

WARNING:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function

on the tool. Failure to switch off and unplug the tool

may result in serious personal injury from accidental

start-up.

Blade guard (Fig. 3)

When lowering the handle, the blade guard rises

automatically. The blade guard returns to its original

position when the cut is completed and the handle is

raised.

WARNING:

• Never defeat or remove the blade guard or the

spring which attaches to the guard. An exposed

blade as a result of defeated guarding may result in

serious personal injury during operation.

In the interest of your personal safety, always maintain the

blade guard in good condition. Any irregular operation of

the blade guard should be corrected immediately. Check

to assure spring loaded return action of guard.

WARNING:

• Never use the tool if the blade guard or spring are

damaged, faulty or removed. Operation of the tool

with a damaged, faulty or removed guard may result in

serious personal injury.

If the see-through blade guard becomes dirty, or sawdust

adheres to it in such a way that the blade and/or

workpiece is no longer easily visible, unplug the saw and

clean the guard carefully with a damp cloth. Do not use

solvents or any petroleum-based cleaners on the plastic

guard because this may cause damage to the guard.

If the blade guard becomes dirty and needs to be cleaned

for proper operation follow the steps below:

With the tool switched off and unplugged, use the

supplied socket wrench to loosen the hex bolt holding the

center cover. Loosen the hex bolt by turning it

counterclockwise and raise the blade guard and center

cover. (Fig. 4)

With the blade guard so positioned, cleaning can be more

completely and efficiently accomplished. When cleaning

is complete reverse procedure above and secure bolt. Do

not remove spring holding blade guard. If guard becomes

damaged through age or UV light exposure, contact a

Makita service center for a new guard. DO NOT DEFEAT

OR REMOVE GUARD.

Positioning kerf board (Fig. 5 & 6)

This tool is provided with the kerf boards in the turn base

to minimize tearing on the exit side of a cut. The kerf

boards are factory adjusted so that the saw blade does

not contact the kerf boards. Before use, adjust the kerf

boards as follows:

First, unplug the tool. Loosen all the screws (3 each on left

and right) securing the kerf boards. Re-tighten them only

to the extent that the kerf boards can still be easily moved

by hand. Lower the handle fully and push in the stopper

pin to lock the handle in the lowered position. Loosen the

screw which secures the slide poles. Pull the carriage

toward you fully. Adjust the kerf boards so that the kerf

boards just contact the sides of the blade teeth. Tighten

the front screws (do not tighten firmly). Push the carriage

toward the guide fence fully and adjust the kerf boards so

that the kerf boards just contact the sides of blade teeth.

Tighten the rear screws (do not tighten firmly).

14

After adjusting the kerf boards, release the stopper pin

and raise the handle. Then tighten all the screws securely.

NOTICE:

• After setting the bevel angle ensure that the kerf

boards are adjusted properly. Correct adjustment of

the kerf boards will help provide proper support of the

workpiece minimizing workpiece tear out.

Maintaining maximum cutting capacity

This tool is factory adjusted to provide the maximum

cutting capacity for a 255 mm saw blade.

Unplug the tool before any adjustment is attempted.

When installing a new blade, always check the lower limit

position of the blade and if necessary, adjust it as follows:

(Fig. 7 & 8)

First, unplug the tool. Push the carriage toward the guide

fence fully and lower the handle completely. Use the hex.

wrench to turn the adjusting bolt until the periphery of the

blade extends slightly below the top surface of the turn

base at the point where the front face of the guide fence

meets the top surface of the turn base.

With the tool unplugged, rotate the blade by hand while

holding the handle all the way down to be sure that the

blade does not contact any part of the lower base. Re-

adjust slightly, if necessary.

WARNING:

• After installing a new blade and with the tool

unplugged, always be sure that the blade does not

contact any part of the lower base when the handle

is lowered completely. If a blade makes contact with

the base it may cause kickback and result in serious

personal injury.

Stopper arm (Fig. 9)

The lower limit position of the blade can be easily

adjusted with the stopper arm. To adjust it, move the

stopper arm in the direction of the arrow as shown in the

figure. Adjust the adjusting screw so that the blade stops

at the desired position when lowering the handle fully.

Adjusting the miter angle (Fig. 10)

Loosen the grip by turning counterclockwise. Turn the turn

base while pressing down the lock lever. When you have

moved the grip to the position where the pointer points to

the desired angle on the miter scale, securely tighten the

grip clockwise.

CAUTION:

• After changing the miter angle, always secure the turn

base by tightening the grip firmly.

NOTICE:

• When turning the turn base, be sure to raise the handle

fully.

Adjusting the bevel angle (Fig. 11)

To adjust the bevel angle, loosen the lever at the rear of

the tool counterclockwise. Unlock the arm by pushing the

handle somewhat strongly in the direction that you intend

to tilt the saw blade.

NOTE:

• Lever can be adjusted to a different lever angle by

removing the screw holding the lever and securing the

lever at a desired angle. (Fig. 12)

Tilt the saw blade until the pointer points to the desired

angle on the bevel scale. Then tighten the lever clockwise

firmly to secure the arm. (Fig. 13)

When tilting the carriage to the right, tilt the carriage to the

left slightly after loosening the lever and press the

releasing button. With the releasing button being pressed,

tilt the carriage to the right. (Fig. 14)

Tilt the saw blade until the pointer points to the desired

angle on the bevel scale. Then tighten the lever clockwise

firmly to secure the arm.

• When changing bevel angles, be sure to position the

kerf boards appropriately as explained in the

“Positioning kerf boards” section.

CAUTION:

• After changing the bevel angle, always secure the arm

by tightening the lever clockwise.

NOTICE:

• When tilting the saw blade be sure the handle is fully

raised.

• When changing bevel angles, be sure to position the

kerf boards appropriately as explained in the

“Positioning kerf boards” section.

Slide lock adjustment (Fig. 15)

To lock the slide pole, turn the locking screw clockwise.

Switch action

For European countries (Fig. 16)

To prevent the switch trigger from being accidentally

pulled, a lock-off button is provided. To start the tool, push

the lever to the left, press in the lock-off button and then

pull the switch trigger. Release the switch trigger to stop.

WARNING:

• Before plugging in the tool, always check to see

that the switch trigger actuates properly and

returns to the “OFF” position when released. Do

not pull the switch trigger hard without pressing in

the lock-off button. This can cause switch

breakage. Operating a tool with a switch that does not

actuate properly can lead to loss of control and serious

personal injury.

A hole is provided in the switch trigger for insertion of

padlock to lock the tool off.

For all countries other than European countries

(Fig. 17)

To prevent the switch trigger from being accidentally

pulled, a lock-off button is provided. To start the tool,

press in the lock-off button and pull the switch trigger.

Release the switch trigger to stop.

WARNING:

• Before plugging in the tool, always check to see

that the switch trigger actuates properly and

returns to the “OFF” position when released. Do

not pull the switch trigger hard without pressing in

the lock-off button. This can cause switch

breakage. Operating a tool with a switch that does not

15

actuate properly can lead to loss of control and serious

personal injury.

A hole is provided in the switch trigger for insertion of

padlock to lock the tool off.

WARNING:

• Do not use a lock with a shank or cable any smaller

than 6.35 mm in diameter. A smaller shank or cable

may not properly lock the tool in the off position and

unintentional operation may occur resulting in serious

personal injury.

• NEVER use tool without a fully operative switch

trigger. Any tool with an inoperative switch is HIGHLY

DANGEROUS and must be repaired before further

usage or serious personal injury may occur.

• For your safety, this tool is equipped with a lock-off

button which prevents the tool from unintended

starting. NEVER use the tool if it runs when you simply

pull the switch trigger without pressing the lock-off

button. A switch in need of repair may result in

unintentional operation and serious personal injury.

Return tool to a Makita service center for proper repairs

BEFORE further usage.

• NEVER defeat the lock-off button by taping down or

some other means. A switch with a defeated lock-off

button may result in unintentional operation and

serious personal injury.

Electronic function

Soft start feature

• This function allows the smooth start-up of the tool by

limiting the start-up torque.

Laser beam action

For model LS1017L only

NOTE:

• Before the first use, install the dry cells provided

separately from the tool in the cell box. Refer to the

section titled “Replacing the dry cells for laser unit” for

the installment.

CAUTION:

• When not in use, be sure to turn off the laser. (Fig. 18)

CAUTION:

• Never look into the laser beam. Direct laser beam may

injure your eyes.

• LASER RADIATION, DO NOT STARE INTO THE

BEAM, CLASS 2 LASER PRODUCT.

• Before shifting the laser line or performing

maintenance adjustment, be sure to unplug the tool.

To turn on the laser beam, press the upper position (I) of

the switch. To turn off the laser beam, press the lower

position (0) of the switch.

Laser line can be shifted to either the left or right side of

the saw blade by loosening the screw holding the laser

unit box and shifting it in the desired direction. After

shifting, be sure to tighten the screw. (Fig. 19)

Laser line is factory adjusted so that it is positioned within

1 mm from the side surface of the blade (cutting position).

NOTE:

• When laser line appears dim and hard to see because

of direct sunlight, relocate the work area to a place

where there is less direct sunlight.

Replacing the dry cells for laser unit

(Fig. 20 & 21)

Remove the lid for the dry cells for laser unit by sliding

while pressing it. Take out the old dry cells and put the

new ones as shown in the figure. After replacing, return

the lid to cover it.

Cleaning of the lens for the laser light

If the lens for the laser light becomes dirty, or sawdust

adheres to it in such a way that the laser line is no longer

easily visible, unplug the saw and remove and clean the

lens for the laser light carefully with a damp, soft cloth. Do

not use solvents or any petroleum-based cleaners on the

lens.

NOTE:

• When laser line is dim and almost or entirely invisible

because of the direct sunlight in the indoor or outdoor

window-by work, relocate the work area to a place not

exposed to the direct sunlight.

ASSEMBLY

WARNING:

• Always be sure that the tool is switched off and

unplugged before working on the tool. Failure to

switch off and unplug the tool may result in serious

personal injury.

Storage of socket wrench with hex

wrench on its other end (Fig. 22)

The socket wrench is stored as shown in the figure. When

the socket wrench is needed it can be pulled out of the

wrench holder.

After using the socket wrench it can be stored by returning

it to the wrench holder.

Installing or removing saw blade

WARNING:

• Always be sure that the tool is switched off and

unplugged before installing or removing the blade.

Accidental start up of the tool may result in serious

personal injury.

• Use only the Makita socket wrench provided to

install or remove the blade. Failure to use the wrench

may result in overtightening or insufficient tightening of

the hex bolt and serious personal injury. (Fig. 23)

Lock the handle in the raised position by pushing in the

stopper pin. (Fig. 24)

To remove the blade, use the socket wrench to loosen the

hex bolt holding the center cover by turning it

counterclockwise. Raise the blade guard and center

cover. (Fig. 25)

Press the shaft lock to lock the spindle and use the socket

wrench to loosen the hex bolt clockwise. Then remove the

hex bolt, outer flange and blade.

16

NOTE:

• If the inner flange is removed be sure to install it on the

spindle with its protrusion facing away from the blade. If

the flange is installed incorrectly the flange will rub

against the machine. (Fig. 26)

To install the blade, mount it carefully onto the spindle,

making sure that the direction of the arrow on the surface

of the blade matches the direction of the arrow on the

blade case.

Install the outer flange and hex bolt, and then use the

socket wrench to tighten the hex bolt (left-handed)

securely counterclockwise while pressing the shaft lock.

For all countries other than European countries

(Fig. 27)

WARNING:

• The black ring 25 mm in outer diameter and the silver

ring 25.4 mm in outer diameter are factory-installed as

shown in the figure. When using a blade with 25 mm

hole diameter, replace the silver ring with the black

ring. Before mounting the blade onto the spindle,

always be sure that the correct ring for the blade’s

arbor hole you intend to use is installed between

the inner and the outer flanges. Use of the incorrect

arbor hole ring may result in the improper mounting of

the blade causing blade movement and severe

vibration resulting in possible loss of control during

operation and in serious personal injury.

For European countries

CAUTION:

• The ring 30 mm in outer diameter is factory-installed

between the inner and outer flanges.

Install the outer flange and hex bolt, and then use the

socket wrench to tighten the hex bolt securely

counterclockwise while pressing the shaft lock. (Fig. 28)

Return the blade guard and center cover to its original

position. Then tighten the hex bolt clockwise to secure the

center cover. Release the handle from the raised position

by pulling the stopper pin. Lower the handle to make sure

that the blade guard moves properly. Make sure the shaft

lock has released spindle before making cut.

Dust bag (accessory) (Fig. 29)

The use of the dust bag makes cutting operations cleaner

and dust collection easier. To attach the dust bag, fit it

onto the dust nozzle.

When the dust bag is about half full, remove the dust bag

from the tool and pull the fastener out. Empty the dust bag

of its contents, tapping it lightly so as to remove particles

adhering to the insides which might hamper further

collection.

NOTE:

If you connect a vacuum cleaner to your saw, cleaner

operations can be performed.

Securing workpiece

WARNING:

• It is extremely important to always secure the

workpiece correctly with the proper type of vise or

crown molding stoppers. Failure to do so may result

in serious personal injury and cause damage to the tool

and/or the workpiece.

• After a cutting operation do not raise the blade

until it has come to a complete stop. The raising of a

coasting blade may result in serious personal injury

and damage to the workpiece.

• When cutting a workpiece that is longer than the

support base of the saw, the material should be

supported the entire length beyond the support

base and at the same height to keep the material

level. Proper workpiece support will help avoid blade

pinch and possible kickback which may result in

serious personal injury. Do not rely solely on the

vertical vise and/or horizontal vise to secure the

workpiece. Thin material tends to sag. Support

workpiece over its entire length to avoid blade pinch

and possible KICKBACK. (Fig. 30)

Guide fence (SLIDING FENCES which are

upper and lower fences) adjustment

(Fig. 31)

WARNING:

• Before operating the tool, make sure that the sliding

fence is secured firmly.

• Before bevel-cutting, make sure that no part of the

tool, especially the blade, contacts the upper and

lower fences when fully lowering and raising the

handle in any position and while moving the

carriage through its full range of travel. If the tool or

blade makes contact with the fence this may result in

kickback or unexpected movement of the material and

serious personal injury. (Fig. 32)

CAUTION:

• When performing bevel cuts, slide the sliding fence to

the left and secure it as shown in the figure. Otherwise,

it will contact the blade or a part of the tool, causing

possible serious injury to the operator.

This tool is equipped with the sliding fence which should

ordinarily be positioned as shown in the figure.

However, when performing left bevel cuts, set it to the left

position as shown in the figure if the tool head contacts it.

When bevel-cutting operations are complete, don’t forget

to return the sliding fence to the original position and

secure it by firmly tightening the clamping screw.

Vertical vise (Fig. 33)

The vertical vise can be installed on either the left or right

side of the guide fence. Insert the vise rod into the hole in

the guide fence and tighten the screw on the back of the

guide fence to secure the vise rod.

Position the vise arm according to the thickness and

shape of the workpiece and secure the vise arm by

tightening the screw. If the screw to secure the vise arm

contacts the guide fence, install the screw on the opposite

side of vise arm. Make sure that no part of the tool

contacts the vise when lowering the handle fully and

pulling or pushing the carriage all the way. If some part

contacts the vise, re-position the vise.

Press the workpiece flat against the guide fence and the

turn base. Position the workpiece at the desired cutting

position and secure it firmly by tightening the vise knob.

17

WARNING:

• The workpiece must be secured firmly against the

turn base and guide fence with the vise during all

operations. If the workpiece is not properly secured

against the fence the material may move during the

cutting operation causing possible damage to the

blade, causing the material to be thrown and loss of

control resulting in serious personal injury.

Horizontal vise (optional accessory)

(Fig. 34)

The horizontal vise can be installed in two positions on

either the left or right side of the base. When performing

10° or greater miter cuts, install the horizontal vise on the

side opposite the direction in which the turn base is to be

turned. (Fig. 35)

By flipping the vise nut counterclockwise, the vise is

released, and rapidly moves in and out. To grip the

workpiece, push the vise knob forward until the vise plate

contacts the workpiece and flip the vise nut clockwise.

Then turn the vise knob clockwise to secure the

workpiece.

The maximum width of workpiece which can be secured

by the horizontal vise is 215 mm.

WARNING:

• Always rotate the vise nut clockwise until the

workpiece is properly secured. If the workpiece is

not properly secured the material may move during the

cutting operation causing possible damage to the

blade, causing the material to be thrown and loss of

control resulting in serious personal injury.

• When cutting a thin workpiece, such as base boards,

against the fence, always use the horizontal vise.

Holders (Fig. 36)

The holders can be installed on either side as a

convenient means of holding workpieces horizontally. Slip

fully the holder rods into the holes in the base. Then

tighten the holders securely with the screws.

WARNING:

• Always support a long workpiece so it is level with

the top surface of the turn base for an accurate cut

and to prevent dangerous loss of tool control.

Proper workpiece support will help avoid blade pinch

and possible kickback which may result in serious

personal injury.

OPERATION

NOTICE:

• Before use, be sure to release the handle from the

lowered position by pulling the stopper pin.

• Do not apply excessive pressure on the handle when

cutting. Too much force may result in overload of the

motor and/or decreased cutting efficiency. Push down

handle with only as much force as is necessary for

smooth cutting and without significant decrease in

blade speed.

• Gently press down the handle to perform the cut. If the

handle is pressed down with force or if lateral force is

applied, the blade will vibrate and leave a mark (saw

mark) in the workpiece and the precision of the cut will

be impaired.

• During a slide cut, gently push the carriage toward the

guide fence without stopping. If the carriage movement

is stopped during the cut, a mark will be left in the

workpiece and the precision of the cut will be impaired.

WARNING:

• Make sure the blade is not contacting the

workpiece, etc. before the switch is turned on.

Turning the tool on with the blade in contact with the

workpiece may result in kickback and serious personal

injury.

1. Press cutting (cutting small workpieces) (Fig. 37)

Workpieces up to 91 mm high and 70 mm wide can be

cut in the following manner.

Push the carriage toward the guide fence fully and

tighten the locking screw clockwise to secure the

carriage. Secure the workpiece correctly with the

proper type of vise. Switch on the tool without the

blade making any contact and wait until the blade

attains full speed before lowering. Then gently lower

the handle to the fully lowered position to cut the

workpiece. When the cut is completed, switch off the

tool and WAIT UNTIL THE BLADE HAS COME TO A

COMPLETE STOP before returning the blade to its

fully elevated position.

WARNING:

• Firmly tighten the knob clockwise so that the

carriage will not move during operation. Insufficient

tightening of the knob may cause possible kickback

which may result in serious personal injury.

2. Slide (push) cutting (cutting wide workpieces)

(Fig. 38)

Loosen the locking screw counterclockwise so that the

carriage can slide freely. Secure the workpiece with

the proper type of vise. Pull the carriage toward you

fully. Switch on the tool without the blade making any

contact and wait until the blade attains full speed.

Press the handle down and PUSH THE CARRIAGE

TOWARD THE GUIDE FENCE AND THROUGH THE

WORKPIECE. When the cut is completed, switch off

the tool and WAIT UNTIL THE BLADE HAS COME

TO A COMPLETE STOP before returning the blade to

its fully elevated position.

WARNING:

• Whenever performing a slide cut, first pull the

carriage full towards you and press the handle all

the way down, then push the carriage toward the

guide fence. Never start the cut with the carriage

not pulled fully toward you. If you perform the slide

cut without the carriage pulled fully toward you

unexpected kickback may occur and serious personal

injury may result.

• Never attempt to perform a slide cut by pulling the

carriage towards you. Pulling the carriage towards

you while cutting may cause unexpected kickback

resulting in possible serious personal injury.

• Never perform the slide cut with the handle locked in

the lowered position.

• Never loosen the locking screw which secures the

carriage while the blade is rotating. A loose carriage

18

while cutting may cause unexpected kickback resulting

in possible in serious personal injury.

3. Miter cutting

Refer to the previously covered “Adjusting the miter

angle”.

4. Bevel cut (Fig. 39)

Loosen the lever and tilt the saw blade to set the bevel

angle (Refer to the previously covered “Adjusting the

bevel angle”). Be sure to retighten the lever firmly to

secure the selected bevel angle safely. Secure the

workpiece with a vise. Make sure the carriage is pulled

all the way back toward the operator. Switch on the

tool without the blade making any contact and wait

until the blade attains full speed. Then gently lower the

handle to the fully lowered position while applying

pressure in parallel with the blade and PUSH THE

CARRIAGE TOWARD THE GUIDE FENCE TO CUT

THE WORKPIECE. When the cut is completed, switch

off the tool and WAIT UNTIL THE BLADE HAS COME

TO A COMPLETE STOP before returning the blade to

its fully elevated position.

WARNING:

• After setting the blade for a bevel cut, before

operating the tool ensure that the carriage and

blade will have free travel throughout the entire

range of the intended cut. Interruption of the carriage

or blade travel during the cutting operation may result

in kickback and serious personal injury.

• While making a bevel cut keep hands out of the

path of the blade. The angle of the blade may confuse

the operator as to the actual blade path while cutting

and contact with the blade will result in serious

personal injury.

• The blade should not be raised until it has come to

a complete stop. During a bevel cut the piece cut off

may come to rest against the blade. If the blade is

raised while it is rotating the cut-off piece maybe

ejected by the blade causing the material to fragment

which may result in serious personal injury.

NOTICE:

• When pressing down the handle, apply pressure in

parallel with the blade. If a force is applied

perpendicularly to the turn base or if the pressure

direction is changed during a cut, the precision of the

cut will be impaired.

• Before bevel-cutting, an adjustment of the upper fence

and lower fence maybe required. Refer to the section

titled “Guide fence adjustment”.

5. Compound cutting

Compound cutting is the process in which a bevel

angle is made at the same time in which a miter angle

is being cut on a workpiece. Compound cutting can be

performed at the angle shown in the table.

When performing compound cutting, refer to “Press

cutting”, “Slide cutting”, “Miter cutting” and “Bevel cut”

explanations.

6. Cutting crown and cove moldings

Crown and cove moldings can be cut on a compound

miter saw with the moldings laid flat on the turn base.

There are two common types of crown moldings and

one type of cove moldings; 52/38° wall angle crown

molding, 45° wall angle crown molding and 45° wall

angle cove molding. See illustrations. (Fig. 40)

There are crown and cove molding joints which are

made to fit “Inside” 90° corners ((1) and (2) in Fig. A)

and “Outside” 90° corners ((3) and (4) in Fig. A).

(Fig. 41 & 42)

Measuring

Measure the wall length and adjust workpiece on table

to cut wall contact edge to desired length. Always

make sure that cut workpiece length at the back of

the workpiece is the same as wall length. Adjust cut

length for angle of cut. Always use several pieces for

test cuts to check the saw angles.

When cutting crown and cove moldings, set the bevel

angle and miter angle as indicated in the table (A) and

position the moldings on the top surface of the saw

base as indicated in the table (B).

In the case of left bevel cut

Table (A)

Table (B)

Example:

In the case of cutting 52/38° type crown molding for

position (1) in Fig. A:

• Tilt and secure bevel angle setting to 33.9° LEFT.

• Adjust and secure miter angle setting to 31.6°

RIGHT.

• Lay crown molding with its broad back (hidden)

surface down on the turn base with its CEILING

CONTACT EDGE against the guide fence on the

saw.

• The finished piece to be used will always be on the

LEFT side of the blade after the cut has been

made.

7. Cutting aluminum extrusion (Fig. 43 & 44)

When securing aluminum extrusions, use spacer

blocks or pieces of scrap as shown in the figure to

prevent deformation of the aluminum. Use a cutting

lubricant when cutting the aluminum extrusion to

prevent build-up of the aluminum material on the

blade.

Miter angle Bevel angle

Left and Right 0° - 45° Left 0° - 45°

Molding

position in

Fig. A

Bevel angle Miter angle

52/38° type 45° type 52/38° type 45° type

For inside

corner

(1)

Left 33.9° Left 30°

Right 31.6° Right 35.3°

(2)

Left 31.6° Left 35.3°

For outside

corner

(3)

(4) Right 31.6° Right 35.3°

Molding

position in

Fig. A

Molding edge against guide

fence

Finished piece

For inside

corner

(1)

Ceiling contact edge should be

against guide fence.

Finished piece will

be on the Left side

of blade.

(2)

Wall contact edge should be

against guide fence.

For outside

corner

(3)

Finished piece will

be on the Right

side of blade.

(4)

Ceiling contact edge should be

against guide fence.

19

WARNING:

• Never attempt to cut thick or round aluminum

extrusions. Thick or round aluminum extrusions can

be difficult to secure and may work loose during the

cutting operation which may result in loss of control and

serious personal injury.

8. Wood facing

Use of wood facing helps to assure splinter-free cuts

in workpieces. Attach a wood facing to the guide fence

using the holes in the guide fence.

See the figure concerning the dimensions for a

suggested wood facing. (Fig. 45)

CAUTION:

• Use straight wood of even thickness as the wood

facing.

WARNING:

• Use screws to attach the wood facing to the guide

fence. The screws should be installed so that the

screw heads are below the surface of the wood

facing so that they will not interfere with the

positioning of the material being cut. Misalignment

of the material being cut can case unexpected

movement during the cutting operation which may

result in a loss of control and serious personal injury.

NOTICE:

• When the wood facing is attached, do not turn the turn

base with the handle lowered. The blade and/or the

wood facing will be damaged.

9. Groove cutting (Fig. 46)

A dado type cut can be made by proceeding as

follows:

Adjust the lower limit position of the blade using the

adjusting screw and the stopper arm to limit the cutting

depth of the blade. Refer to “Stopper arm” section

described previously.

After adjusting the lower limit position of the blade, cut

parallel grooves across the width of the workpiece

using a slide (push) cut as shown in the figure. Then

remove the workpiece material between the grooves

with a chisel.

WARNING:

• Do not attempt to perform this type of cut by using

a wider type blade or dado blade. Attempting to

make a groove cut with a wider blade or dado blade

could lead to unexpected cutting results and kickback

which may result in serious personal injury

• Be sure to return the stopper arm to the original

position when performing other than groove

cutting. Attempting to make cuts with the stopper arm

in the incorrect position could lead to unexpected

cutting results and kickback which may result in serious

personal injury.

CAUTION:

• Be sure to return the stopper arm to the original

position when performing other than groove cutting.

Carrying tool (Fig. 47)

Make sure that the tool is unplugged. Secure the blade at

0° bevel angle and the turn base at the full right miter

angle position. Secure the slide poles so that the lower

slide pole is locked in the position of the carriage fully

pulled to operator and the upper poles are locked in the

position of the carriage fully pushed forward to the guide

fence (refer to the section titled “Slide lock adjustment”.)

Lower the handle fully and lock it in the lowered position

by pushing in the stopper pin.

Wind the power supply cord using the cord rests.

WARNING:

• Stopper pin is only for carrying and storage

purposes and should never be used for any cutting

operations. The use of the stopper pin for cutting

operations may cause unexpected movement of the

saw blade resulting in kickback and serious personal

injury.

Carry the tool by holding both sides of the tool base as

shown in the figure. If you remove the holders, dust bag,

etc., you can carry the tool more easily.

CAUTION:

• Always secure all moving portions before carrying the

tool. If portions of the tool move or slide while being

carried loss of control or balance may occur resulting in

personal injury.

MAINTENANCE

WARNING:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection

or maintenance. Failure to unplug and switch off the

tool may result in accidental start up of the tool which

may result in serious personal injury.

• Always be sure that the blade is sharp and clean

for the best and safest performance. Attempting a

cut with a dull and/or dirty blade may cause kickback

and result in a serious personal injury.

NOTICE:

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

Adjusting the cutting angle

This tool is carefully adjusted and aligned at the factory,

but rough handling may have affected the alignment. If

your tool is not aligned properly, perform the following:

1. Miter angle (Fig. 48)

Push the carriage toward the guide fence and tighten

the locking screw to secure the carriage.

Loosen the grip which secures the turn base. Turn the

turn base so that the pointer points to 0° on the miter

scale. Then turn the turn base slightly clockwise and

counterclockwise to seat the turn base in the 0° miter

notch. (Leave as it is if the pointer does not point to

0°.) Loosen the hex sockets bolts securing the guide

fence using the socket wrench. (Fig. 49)

Lower the handle fully and lock it in the lowered

position by pushing in the stopper pin. Square the side

of the blade with the face of the guide fence using a

triangular rule, try-square, etc. Then securely tighten

the hex socket bolts on the guide fence in order

starting from the right side. (Fig. 50)

20

Make sure that the pointer points to 0° on the miter

scale. If the pointer does not point to 0°, loosen the

screw which secures the pointer and adjust the pointer

so that it will point to 0°.

2. Bevel angle

(1) 0° bevel angle (Fig. 51)

Push the carriage toward the guide fence and

tighten the locking screw to secure the carriage.

Lower the handle fully and lock it in the lowered

position by pushing in the stopper pin. Loosen the

lever at the rear of the tool. (Fig. 52)

Turn the hex bolt on the right side of the arm two

or three revolutions counterclockwise to tilt the

blade to the right. (Fig. 53)

Carefully square the side of the blade with the top

surface of the turn base using the triangular rule,

try-square, etc. by turning the hex bolt on the right

side of the arm clockwise. Then tighten the lever

securely. (Fig. 54)

Make sure that the pointer on the arm point to 0°

on the bevel scale on the arm holder. If they do not

point to 0°, loosen the screw which secure the

pointer and adjust it so that it will point to 0°.

(2) 45° bevel angle (Fig. 55)

Adjust the 45° bevel angle only after performing 0°

bevel angle adjustment. To adjust left 45° bevel

angle, loosen the lever and tilt the blade to the left

fully. Make sure that the pointer on the arm points

to 45° on the bevel scale on the arm holder. If the

pointer does not point to 45°, turn the 45° bevel

angle adjusting bolt on the right side of the arm

holder until the pointer points to 45°.

To adjust the right 5° bevel angle, perform the

same procedure as that described above.

Replacing carbon brushes (Fig. 56)

Remove and check the carbon brushes regularly. Replace

when they wear down to 3 mm in length. Keep the carbon

brushes clean and free to slip in the holders. Both carbon

brushes should be replaced at the same time. Use only

identical carbon brushes. (Fig. 57)

Use a screwdriver to remove the brush holder caps. Take

out the worn carbon brushes, insert the new ones and

secure the brush holder caps.

After use

• After use, wipe off chips and dust adhering to the tool

with a cloth or the like. Keep the blade guard clean

according to the directions in the previously covered

section titled “Blade guard”. Lubricate the sliding

portions with machine oil to prevent rust.

• When storing the tool, pull the carriage toward you

fully.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers, always

using Makita replacement parts.

ACCESSORIES

WARNING:

• These Makita accessories or attachments are

recommended for use with your Makita tool

specified in this manual. The use of any other

accessories or attachments may result in serious

personal injury.

• Only use the Makita accessory or attachment for its

stated purpose. Misuse of an accessory or

attachment may result in serious personal injury.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Steel & Carbide-tipped saw blades

• Vise assembly (Horizontal vise)

• Vertical vise

• Socket wrench with hex wrench on its other end

• Holder

• Dust bag

• Elbow

• Triangular rule

Noise

ENG905-1

The typical A-weighted noise level determined according

to EN61029:

Sound pressure level (L

pA

): 97 dB (A)

Sound power level (L

WA

): 103 dB (A)

Uncertainty (K): 3 dB (A)

Wear ear protection.

Vibration

ENG900-1

The vibration total value (tri-axial vector sum) determined

according to EN61029:

Vibration emission (a

h

): 2.5 m/s

2

or less

Uncertainty (K): 1.5 m/s

2

ENG901-1

• The declared vibration emission value has been

measured in accordance with the standard test method

and may be used for comparing one tool with another.

• The declared vibration emission value may also be

used in a preliminary assessment of exposure.

WARNING:

• The vibration emission during actual use of the power

tool can differ from the declared emission value

depending on the ways in which the tool is used.

• Be sure to identify safety measures to protect the

operator that are based on an estimation of exposure in

the actual conditions of use (taking account of all parts

of the operating cycle such as the times when the tool

is switched off and when it is running idle in addition to

the trigger time).

Miter saw blades

For smooth and precise cutting in

various materials.

Combination

General purpose blade for fast and

smooth rip, crosscuts and miters.

Crosscutting

For smoother cross grain cuts. Slices

cleanly against the grain.

Fine cross cuts

For sand-free cuts cleanly against the

grain.

Non-ferrous

metals miter saw

blades

For miters in aluminum, copper,

brass, tubing, and other non-ferrous

metals.

21

For European countries only ENG015-2

Noise and Vibration

The typical A-weighted noise levels are

sound pressure level: 97 dB (A)

sound power level: 103 dB (A)

Uncertainty: 3 dB (A)

Wear ear protection.

The typical weighted root mean square acceleration value

is not more than 2.5 m/s

2

.

Uncertainty (K):1.5 m/s

2

These values have been obtained according to EN61029.

For European countries only

ENH003-12

EC Declaration of Conformity

We Makita Corporation as the responsible

manufacturer declare that the following Makita

machine(s):

Designation of Machine:

Slide Compound Miter Saw

Model No./ Type: LS1017, LS1017L

are of series production and

Conforms to the following European Directives:

2006/42/EC

And are manufactured in accordance with the following

standards or standardised documents:

EN61029

The technical documentation is kept by our authorised

representative in Europe who is:

Makita International Europe Ltd.,

Michigan Drive, Tongwell,

Milton Keynes, MK15 8JD, England

6. 11. 2009

Tomoyasu Kato

Director

Makita Corporation

3-11-8, Sumiyoshi-cho,

Anjo, Aichi, JAPAN

Page is loading ...

ALA

Makita Corporation

Anjo, Aichi, Japan

JM2318A026 www.makita.com

Makita LS1017L Owner's manual

This manual is also suitable for

Makita LS1017L Owner's manual

in other languages

Related papers

Other documents