Craftsman 13953976SRT Owner's manual

Owner's Manual/Manual Del Propietario

CRRFTSMRN°

1/2 HP

GARAGE DOOR OPENER

ABRIDOR DE PUERTA DE COCHERA

For Residential Use Only/S61o para uso residencial

ModellModelo 139.53976SRT

m

Z

!==,

m

"o

Z_

0

CAUTION"

Read and follow all safety rules

and operating instructions before

first use of this product.

Fasten the manual near the garage

door after installation.

PRECAUCION:

Leer y seguir todas las regias de

seguridad y las instrucciones de

operaci6n antes de usar este

producto por primera vez.

Guardar este manual cerca de la

puerta del garaje.

00°s

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A

www.sears.com/craftsman

TABLE OF CONTENTS

In troduc tion 2=7

Safety symbol and signal word review ........................ 2

Preparing your garage door ........................................ 3

Tools needed ............................................................... 3

Planning .................................................................. 4-5

Carton inventory .......................................................... 6

Hardware inventory ..................................................... 7

Assembly 8-11

Assemble the rail and install trolley ............................. 8

Fasten rail to motor unit and install idler pulley .......... 9

Install chain/cable and attach sprocket cover ........... 10

Tighten the chain ....................................................... 11

Installa tion 11 =2 7

Installation safety instructions .................................... 11

Determine the header bracket location ................ 12-13

Install the header bracket .......................................... 14

Attach the rail to the header bracket ......................... 15

Position the opener ................................................... 16

Hang the opener ....................................................... 17

Install the door control ............................................... 18

Install the light and lens ............................................ 19

Attach the emergency release rope and handle ....... 19

Electrical requirements .............................................. 20

Install the safety reversing sensor ....................... 21-23

Fasten the door bracket ....................................... 24-25

Connect the door arm to the trolley ..................... 26-27

Adjustment 28-30

Adjust the travel limits ............................................... 28

Adjust the force ......................................................... 29

Test the safety reversal system ................................. 30

Test the safety reversing sensor ............................... 30

Operation 31=34

Operation safety instructions ..................................... 31

Using your garage door opener ................................ 31

Using the wall-mounted Door Control ....................... 32

To open the door manually ........................................ 32

Care of your garage door opener .............................. 33

Having a problem? .................................................... 34

Programming 35=36

To add a hand-held remote control ........................... 35

To erase all codes ..................................................... 35

3-Function Remotes .................................................. 35

To add or change a Keyless Entry PIN ..................... 36

Repair Parts 37=38

Rail assembly parts ................................................... 37

Installation parts ........................................................ 37

Motor unit assembly parts ......................................... 38

Accessories 39

Warranty

Service Numbers

39

Back cover

iNTRODUCTiON

Safety Symbol

and Signal Word Review

This garage door opener has been designed and tested to offer safe service provided it is installed, operated,

maintained and tested in strict accordance with the instructions and warnings contained in this manual.

Mechanical

Electrical

When you see these Safety Symbols and Signal

Words on the following pages, they will alert you to

the possibility of serious injury or death if you do

not comply with the warnings that accompany them.

The hazard may come from something mechanical

or from electric shock. Read the warnings carefully.

When you see this Signal Word on the following

pages, it will alert you to the possibility of damage to

your garage door and/or the garage door opener if

you do not comply with the cautionary statements

that accompany it. Read them carefully.

Preparing your garage door

Before you begin:

• Disable locks.

• Remove any ropes connected to garage door.

• Complete the following test to make sure your

garage door is balanced and is not sticking or

binding:

1. Lift the door about halfway as shown. Release

the door. If balanced, it should stay in place

supported entirely by its springs.

2. Raise and lower the door to see if there is any

binding or sticking.

If your door binds, sticks, or is out of balance, call

a trained door systems technician.

Topreventpossible SERIOUSINJURYOR DEATH:

, ALWAYScall a trained door systems technician if

garagedoor binds,sticks, or is out of balance.An

unbalancedgaragedoor may not reversewhen

required.

, NEVERtry to loosen, move or adjust garagedoor, door

springs, cables,pulleys, brackets or their hardware, all

of which areunder EXTREMEtension.

, DisableALL locks and remove ALL ropes connectedto

garagedoor BEFOREinstalling and operating garage

door opener to avoidentanglement.

Topreventdamageto garagedoor and opener:

, ALWAYSdisable locks before installing and operating

the opener.

, ONLYoperategaragedoor opener at 120V,60 Hzto

avoid malfunction and damage.

Sectional Door

One-Piece Door

Level

Tools needed

During assembly, installation and adjustment of the

opener, instructions will call for hand tools as

illustrated below.

Stepladder

Drill

Tape Measure

Pencil

Hack Saw

Wire Cutters

3/16", 5/16" and

5/32" Drill Bits Screwdriver

Locking pliers Adjustable End Wrench

Planning

Identify the type and height of your garage door.

Survey your garage area to see if any of the

conditions below apply to your installation. Additional

materials may be required. You may find it helpful to

refer back to this page and the accompanying

illustrations as you proceed with the installation of

your opener.

Depending on your requirements, there are several

installation steps which may call for materials or

hardware not included in the carton.

• Installation Step 1 - Look at the wall or ceiling

above the garage door. The header bracket must

be securely fastened to structural supports.

• Installation Step 5 - Do you have a finished ceiling

in your garage? If so, a support bracket and

additional fastening hardware may be required.

• Installation Step 10- Depending upon garage

construction, extension brackets or wood blocks

may be needed to install sensors.

• Installation Step 10 -Alternate floor mounting of

the safety reversing sensor will require hardware

not provided.

Do you have an access door in addition to the

garage door? If not, Model 53702 Emergency Key

Release is required. See Accessories page.

Look at the garage door where it meets the floor.

Any gap between the floor and the bottom of the

door must not exceed 1/4". Otherwise, the safety

reversal system may not work properly. See

Adjustment Step 3. Floor or door should be

repaired.

SECTIONAL DOOR INSTALLATIONS

• Do you have a steel, aluminum, fiberglass or glass

panel door? If so, horizontal and vertical reinforce-

ment is required (Installation Step 11).

• The opener should be installed above the center of

the door. If there is a torsion spring or center

bearing plate in the way of the header bracket, it

may be installed within 4 feet to the left or right of

the door center. See Installation Steps 1 and 11.

• If your door is more than 7 feet high, see rail

extension kits listed on Accessories page.

SECTIONAL DOOR INSTALLATION

Horizontal and vertical reinforcement

is needed for lightweight garage doors

(fiberglass, steel, aluminum, door with

glass panels, etc.). See page 24 for details.

Header Wall

Rail

Extension Spring

OR

Torsion Spring

Wall-

mounted

Door

Control

Access Door

O

Safety Reversing Sensor

Gap between floor

and bottom of door

must not exceed 1/4".

Safety

Reversing

Sensor

FINISHED CEILING

Support bracket &

fastening hardware

is required.

See page 17.

Motor unit

m

-- Header CLOSED POSITION

Bracket

I_A / Trolley

__OltGarage Trolle

,-'_ __ _ _ ......

/

Door Chain

Spnng o I

__ j ___Straight Emergency

io pot I Release

_ /O_/ _rm _ Rope&Handle

H:_lder /_ _DDoor Arm

Garage_J I Bracket

Door[iJ

Planning (continued)

ONE-PIECE DOOR iNSTALLATiONS

• Generally, a one-piece door does not require

reinforcement. If your door is lightweight, refer to

the information relating to sectional doors in

Installation Step 11.

• Depending on your door's construction, you may

need additional mounting hardware for the door

bracket (Step 11).

Without a properly working safetyreversal system,

persons (particularly small children) could be

SERIOUSLYINJUREDor KILLEDby a closing garage

door.

. Thegap betweenthe bottom of the garagedoor and

the floor MUST NOTexceed1/4". Otherwise,the safety

reversal system may not work properly.

. Thefloor or the garagedoor MUSTberepaired to

eliminate the gap.

ONE-PIECE DOOR WITHOUT TRACK FINISHEDCEILING

Support bracket __L_

& fastening _',_::_ [!t -

h:rdware is required. __

T'_Y?q Header Wall __'_ L_ _:2 "

"Motor unit

I III t ,_ tt I TFr I I _ Wall-mounted

I c.os o os...o.

_o F_ I -_<:-_:__--__-- -:

...... Rope & Handle

and bottom of door must not exceed 1/4". I Header l_q Arm Arm f

Safety Reversing Sensor I ,_,_,_' I\_1 ...... _

I wall _ Garage Door

ONE-PIECE DOOR WiTH TRACK

i

¢

Safety

Reversing Sensor

Floor must be level

across width of door

Reversing

Sensor

CLOSED POSITION

Trolley Stop Bolt Cable

_ Head'elr Cu

Bracket rm

_...._ Door° ° ° ° ° °_°°°°°') j

racket t;o pt

Goaroage Arm ¢-

Chain

Rail

Emergency

Release

i Rope &

Handle

Carton Inventory

Your garage door opener is packaged in two cartons

which contains the motor unit and the parts illustrated

below. Note that accessories will depend on the

model purchased. If anything is missing, carefully

check the packing material. Parts may be stuck in the

foam. Hardware for assembly and installation is

shown on the next page. Save the carton and

packing material until installation and adjustment is

complete,

Passive Infrared Control Console

Security+ Three-Function

Remote Control with Visor Clip (2)

Chain andCabl_

Trolley

Sprocket Cover

'dICrhpiu_ley _ #

Rail ///

Front (header) ///

Header Bracket

Security+ Keyless Entry

#

Rail

Center/Back

Sections

Door Bracket

2-Conductor Bell Wire

White & White/Red

U Bracket

Curved Door

Arm Section

Light Lens

Hanging Brackets

Safety Sensor

Bracket (2)

(2) Safety Reversing Sensors

(1 Sending Eye and 1 Receiving Eye)

with

2-Conductor White & White/Black Bell Wire

attached

Safety Labels

and

Literature

Straight Door

Arm Section

Hardware Inventory

Separate all hardware and group as shown below for the assembly and installation procedures.

ASSEMBLY HARDWARE

Lock Nut Lock Washer Nut

Chain Spreader (2) 1/4"-20 (2) 3/8" (1) 3/8" (1)

Bolt 1/4"-20 x 1-3/4" (2)

Trolley Threaded Shaft (1)

Master

Link (2)

Idler Bolt (1)

INSTALLATION HARDWARE

Carriage Bolt

1/4"-20xl/2" (2)

O

Wing Nut Ring

1/4"-20 (2) Fastener (3)

1111111111

Lag Screw

5/16"-9xl-5/8" (2)

1IIIIIIIIII1

Lag Screw

5/16"-18xl-7/8" (2)

Carriage Bolt

5/16"-18x2-1/2" (2)

ol

Clevis Pin

5/16"x1-1/2" (1)

Hex Screw

5/16"-18x7/8" (4)

Nut 5/16"-18 (8)

Lock Washer 5/16" (7)

Handle

Insulated

Staples (30)

Screw

6ABx1-1/4" (2) Screw 6-32x1" (2)

Dry Wall Anchors (2)

°1

Clevis Pin

5/16"x1-1/4" (1)

Spacer (2)

Clevis Pin

5/16"x1" (1)

Rope

ASSEMBLY STEP 1

Assemble the Rail & Install the Trolley

To avoid installation difficulties, do not run the

garage door opener until instructed to do so,

The front rail has a cut out "window" at the door end

(see illustration). The hole above this window is

larger on the top of the rail than on the bottom. A

smaller hole 3-1/2" away is close to the rail edge.

Rotate the back rail so it has a similar hole close to

the opposite edge, about 4-3/4" from the far end. A

3-piece rail uses two back rails.

1. Remove the straight door arm and clevis pin

packaged inside the front rail and set aside for

Installation Step 12.

2. Align the rail sections on a flat surface exactly as

shown and slide the tapered ends into the larger

ones. Tabs along the side will lock into place.

.

Place the motor unit on packing material to protect

the cover, and rest the back end of the rail on top.

For convenience, put a support under the front

end of the rail.

4. As a temporary trolley stop, clamp a locking pliers

onto the rail, 8" from the center of the idler pulley

hole, as shown.

5. Check to be sure there are 4 black plastic wear

pads inside the inner trolley. If they became loose

during shipping, check all packing material. Snap

them back into position as shown.

6. Connect the inner and outer trolleys as shown.

7. Slide the trolley assembly along the rail from the

back end to the locked pliers.

SMALL HOLES

ALONG OPPOSITE EDGE

OF RAILS

KEEP LARGER

HOLE ON TOP

FRONT RAIL

(TOP)

BACK RAIL

(TOP)

I

End

Back Rails

(TO MOTOR UNIT)

8" Distance from _ Ta_bs

Idler Pulley Hole /_/

Idler /_/

Pulley ===7€_//_,/ Window

Hole _ Cut-Out _Tont Rao/ )

Inner Trolley

ASSEMBLY STEP 2

Fasten the Rail to the Motor Unit

• Insert a 1/4%20xl-3/4 bolt into the cover protection

bolt hole on the back end of the rail as shown.

Tighten securely with a 1/4%20 lock nut.

• Remove the two screws from the top of the motor

unit.

• Attach spreaders to the U bracket by snapping

them into place.

• Place the U bracket, flat side down, on the motor

unit and align the bracket holes with the screw

holes. Fasten with the previously removed screws.

• Align the rail assembly with the top of the motor

unit. Slide the rail end onto the U-bracket, all the

way to the stops that protrude on the top and sides

of the bracket.

HARDWARE SHOWN ACTUAL SIZE '_'_"_:'_','_'1

[_ Lock Nut

Bolt 1/4"-20 x 1-3/4 1/4"-20

Toavoid serious damageto garage door opener,use

only those screws mounted in the top of the opener.

Bolt

"U" Bracket

Cover

Motor Unit

Screws _ _ Sprocket

SLIDE RAIL TO STOPS

ON TOP AND SIDES

OF BRACKET

Lock Nut

)reader

into Back Slots,

then Snap Tab

Into Front Slot

ASSEMBLY STEP 3

Install the Idler Pulley

• Lay the chain/cable beside the rail, as shown.

Grasp the end with the cable loop and pass

approximately 12" of cable through the window.

Allow it to hang until Assembly Step 5.

• Remove the tape from the idler pulley. The inside

center should be pre-greased. If dry, regrease to

ensure proper operation.

• Place the idler pulley into the window as shown.

• Insert the idler bolt from the top through the rail

and pulley. Tighten with a 3/8" lock washer and nut

underneath the rail until the lock washer is

compressed.

• Rotate the pulley to be sure it spins freely.

• Insert a 1/4%20xl-3/4 bolt into the trolley stop hole

in the front of the rail as shown. Tighten securely

with a 1/4%20 lock nut.

Chain and

Cable

Bolt

Washer

_ ___Locking Pliers

Idler_ Trolley

B°lt_ Trolley

_ _StopHole

_ Idler

3/8" Lock i _Pulley

Washer --_l _ Cable Loop

Q_-- 3/8' Nut -

I

Bolt

Trolley

Idler Pulley

HARDWARE SHOWN ACTUAL SIZE

1

Bolt 1/4"-20 x 1-3/4 Lock Nut 1/4"-20

Nut 3/8"

Lock Washer 3/8"

ASSEMBLY STEP 4

Install the Chain/Cable

and Attach the Sprocket Cover

1.Pull the cable around the idler pulley and toward

the trolley.

2. Connect the cable loop to the retaining slot on the

trolley, as shown:

Toavoid possibleserious injury to fingers from moving

garagedoor opener:

, ALWAYSkeephand clear of sprocket while operating

opener•

, Securely attachsprocket cover BEFOREoperating•

• From below, push pins of master link bar up

through cable loop and trolley slot.

• Push master link cap over pins and past pin

notches.

• Slide clip-on spring over cap and onto pin

notches until both pins are securely locked in

place.

3. With the trolley against the pliers, dispense the

remainder of the cable/chain along the rail toward

the motor unit and around the sprocket. The

sprocket teeth must engage the chain.

4. Check to make sure the chain is not twisted, then

connect it to the threaded shaft with the

remaining master link.

5. Thread the inner nut and lock washer onto the the

trolley shaft.

Dispensing Carton

Leave Chain and Cable

IcaSir_:nDlosppenvSinrgtKinking"

Keep Chain and Cable

Taut When Dispensing

6. Insert the trolley threaded shaft through the hole

in the trolley. Be sure the chain is not twisted.

Motor Unit

Sprocket

Back

Tab Slot

Mounting

Plate

10

ASSEMBLY STEP 5

Tighten the Chain

• Spin the inner nut and lock washer down the

threaded shaft, away from the trolley.

• To tighten the chain, turn outer nut in the direction

shown (Figure 1).

• When the chain is approximately 1/2" above the

base of the rail at its midpoint, re-tighten the inner

nut to secure the adjustment.

Sprocket noise can result if chain is too loose.

When installation is complete, you may notice some

chain droop with the door closed. This is normal. If

the chain returns to the position shown in Figure 2

when the door is open, do not re-adjust the chain.

NOTE: During future maintenance, ALWAYS pull the

emergency release handle to disconnect trolley

before adjusting chain.

NOTE: You may notice loosening of chain after

Adjustment Step 3 (Test the Safety Reversal

System). Check for proper tension and readjust

chain if necessary. Then repeat Adjustment Step 3.

You have now finished assembling your garage

door opener. Please read the following warnings

before proceeding to the installation section:

Figure 1

Outer Lock Trolley

Nut Washer Shaft

Figure 2

,,

Chain i

1/2 Inch

I

Base of Rail Mid length of Rail

iNSTALLATiON

IMPORTANT INSTALLATION INSTRUCTIONS

To reduce the risk of severe injury or death:

1. READAND FOLLOWALL INSTALLATIONWARNINGS

AND INSTRUCTIONS.

,

2. Install garagedoor opener only on properly balanced

and lubricated garagedoor. An improperly balanced 9.

door may not reversewhen required and could result in

severeinjury or death.

3. All repairsto cables,spring assemblies and other

hardware MUSTbemadeby atrained door systems 10.

technician beforeinstalling opener.

4. Disable all locks and remove all ropes connected to 11.

garagedoor beforeinstalling opener to avoid

entanglement. 12.

5. install garagedoor opener 7 feet or more abovefloor.

6. Mount emergencyreleasehandle 6 feet abovefloor.

7. NEVERconnect garagedoor openerto power source

until instructed to do so.

NEVERwearwatches, rings or loose clothing while

installing or servicing opener.They could becaught in

garagedoor or opener mechanisms.

install wall-mounted garagedoor control:

, within sight of the garage door

, out of reachof children at minimum height of 5 feet

, awayfrom all moving parts of the door.

Placeentrapmentwarning label on wall next to garage

door control.

Placemanual release/safetyreverse test label in plain

view on inside of garagedoor.

Uponcompletion of installation, test safety reversal

system. Door MUSTreverse on contact with a one-

inch high object (or a 2x4 laid flat) on the floor.

11

iNSTALLATiON STEP 1

Determine the Header Bracket

Location

Toprevent possible SERIOUSINJURYor DEATH:

, HeaderbracketMUSTbe RIGIDLYfastened to

structural support on headerwall or ceiling, otherwise

garagedoor might not reversewhen required. DONOT

install header bracketover drywall.

, Concreteanchors MUST be usedif mounting header

bracket or 2x4 into masonry.

, NEVERtry to loosen, move or adjust garagedoor,

springs, cables,pulleys, brackets, or their hardware, all

of which areunder EXTREMEtension.

. ALWAYScall a trained door systems technician if

garagedoor binds,sticks, or is out of balance.An

unbalancedgaragedoor might not reversewhen

required.

Vertical

Centerline

Finished ......

Ceiling

2x4 Structural

Supports

Installation procedures vary according to garage door

types. Follow the instructions which apply to your

door.

SECTIONAL DOOR

AND ONE-PIECE DOOR WITH TRACK

1.Close the door and mark the inside vertical

centerline of the garage door.

2. Extend the line onto the header wall above the

door.

You can fasten the header bracket within 4 feet

of the left or right of the door center only if a

torsion spring or center bearing plate is in the

way; or you can attach it to the ceiling (see

page 14) when clearance is minimal. (It may be

mounted on the wall upside down if necessary,

to gain approximately 1/2".)

If you need to install the header bracket on a 2x4

(on wall or ceiling), use lag screws (not provided)

to securely fasten the 2x4 to structural supports as

shown here and on page 13.

3. Open your door to the highest point of travel as

shown. Draw an intersecting horizontal line on the

header wall 2" above the high point. This height

will provide travel clearance for the top edge of the

door.

NOTE: Door clearance brackets are available for

sectional doors when headroom clearance is less

than 2't See accessory page 39.

Proceed to Step 2, page 14.

Ceiling

Header Wall

i

' ............2" Track

_- ..... I

Highest Point

of Travel

Door

Sectional door

with curved

track

One-piece

door with

horizontal

track

Header Wal_

2 Track

Highest Point

of Travel

Door

12

ONE-PIECEDOORWITHOUTTRACK

1.Closethedoorandmarktheinsidevertical

centerlineofyourgaragedoor.Extendtheline

ontotheheaderwallabovedoor,asshown.

Ifheadroomclearanceisminimal,youcaninstall

theheaderbracketontheceiling.Seepage14.

Ifyouneedtoinstalltheheaderbracketona2x4

(onwallorceiling),uselagscrews(notprovided)

tosecurelyfastenthe2x4tostructuralsupports

asshown.

2.Openyourdoortothehighestpointoftravelas

shown.Measurethedistancefromthetopofthe

doortothefloor.Subtracttheactualheightofthe

door.Add8"totheremainder.(SeeExample).

3.Closethedooranddrawanintersectinghorizontal

lineontheheaderwallatthedeterminedheight.

NOTE: If the total number of inches exceeds the

height available in your garage, use the maximum

height possible, or refer to page 14 for ceiling

installation.

Header Wall

Unfinished

Ceiling

Vertical

Centedine

2x4

OPTIONAL

CEILING MOUNT

FOR

HEADER BRACKET

EXAMPLE

Distance from top of door

(at highest point of travel) to floor ...................... 92"

Actual height of door .......................................... -88"

Remainder .......................................................... 4"

Add ..................................................................... +8"

Bracket height on header wall ............................ =12"

(Measure UP from top of CLOSED door.)

Proceed to Step 2, page 14.

Door 1

.Jamb

Hardware

Header Wall

Highest Point

of Travel

¢u

ii

C3

Floor

One-piece door without track:

jamb hardware

Door

t

/

s

• J__

J ....

Highest Point

of Travel

Header Wall

t t Jl

'J co

D

Floor

13

One-piece door without track:

pivot hardware

iNSTALLATiON STEP 2

Install the Header Bracket

You can attach the header bracket either to the wall

above the garage door, or to the ceiling. Follow the

instructions which will work best for your particular

requirements. Do not install the header bracket

over drywall. If installing into masonry, use

concrete anchors (not provided).

WALL HEADER BRACKET INSTALLATION

• Center the bracket on the vertical centerline with

the bottom edge of the bracket on the horizontal

line as shown (with the arrow pointing toward the

ceiling).

• Mark the vertical set of bracket holes. Drill 3/16"

pilot holes and fasten the bracket securely to a

structural support with the hardware provided,

Header

-- Wall -

2x4

Structural

Support

Wall Mount

Optional

Mounting Holes

Vertical

Centerline

Lag Screws

5/16"x9x1-5/8"

Spring

HARDWARE SHOWN ACTUAL SIZE

:]IIIIIIII1

Lag Screw

5/16"-9xl -5/8"

Garage

]" -- Door-

Highest Point of

Garage Door Travel Vertical

Centerline

CEILING HEADER BRACKET INSTALLATION

• Extend the vertical centerline onto the ceiling as

shown.

• Center the bracket on the vertical mark, no more

than 6" from the wall. Make sure the arrow is

pointing away from the wall. The bracket can be

mounted flush against the ceiling when clearance

is minimal.

• Mark the side holes. Drill 3/16" pilot holes and

fasten bracket securely to a structural support with

the hardware provided.

Ceiling Mounting Holes

/

Header t

Bracket

/

6" Maximum

Door

Spring

[_ //SS - Finished Ceiling -

Vertical Centerline

Lag Screws

5/16"x9x 1-5/8"

-- Header Wall --

senterline

14

__ Header Wall

Header Bracket

__ Idler Pulley

iNSTALLATiON STEP 3

Attach the Rail to the Header

Bracket

NOTE: (Optional) With an existing Craftsman

installation, you may re-use the old header bracket

with the two plastic spacers included in the hardware

bag. Place the spacers inside the bracket on each

side of the rail, as illustrated.

• Position the opener on the garage floor below the

header bracket. Use packing material as a

protective base. NOTE: If the door spring is in the

way you'll need help. Have someone hold the

opener securely on a temporary support to allow

the rail to clear the spring.

• Position the front rail end within the header bracket

and join with a 5/16"x1-1/2" clevis pin as shown.

• Insert a ring fastener to secure.

Spring

0

Mounting

Hole

Existing

Header Bracket

0

Spacer

Mountin_

Hole

OPTION WITH

EXISTING CRAFTSMAN

INSTALLATION

-- Garage

Door

Opener Carton or

__ Temporary

Support

HARDWARE SHOWN ACTUAL SIZE

O

Clevis Pin 5/16"x1-1/2" Ring fastener

15

iNSTALLATiON STEP 4

Position the Opener

Follow instructions which apply to your door type as

illustrated.

SECTIONAL DOOR OR ONE-PIECE DOOR WITH

TRACK

A 2x4 laid flat is convenient for setting an ideal door-

to-rail distance.

• Raise the opener onto a stepladder. You will need

help at this point if the ladder is not tall enough.

• Open the door all the way and place a 2x4 laid flat

on the top section beneath the rail.

• If the top section or panel hits the trolley when you

raise the door, pull down on the trolley release arm

to disconnect inner and outer sections. Slide the

outer trolley toward the motor unit. The trolley can

remain disconnected until Installation Step 12

is completed.

olley

elease Arm ------_ J

ENGAGED RELEASED V

Toprevent damageto garagedoor, rest garagedoor

opener rail on 2x4 placedon top section of door.

Outer Trolley Inner Trolley

2x4

Door

ONE-PIECE DOOR WITHOUT TRACK

• With the door fully open and parallel to the floor,

measure the distance from the floor to the top of

the door.

• Using a stepladder as a support, raise the top of

the opener to this height.

• The top of the door should be level with the top of

the motor unit. Do not position the opener more

than 2" above this point.

16

iNSTALLATiON STEP 5

Hang the Opener

Two representative installations are shown. Yours

may be different. Hanging brackets should be angled

(Figure 1) to provide rigid support. On finished

ceilings (Figure 2), attach a sturdy metal bracket to

structural supports before installing the opener. This

bracket and fastening hardware are not provided.

(See Accessories.)

1. Measure the distance from each side of the motor

unit to the structural support.

2. Cut both pieces of the hanging bracket to required

lengths.

3. Drill 3/16" pilot holes in the structural supports.

4. Attach one end of each bracket to a support with

5/16"-18xl-7/8" lag screws.

5. Fasten the opener to the hanging brackets with

5/16"-18x7/8" hex screws, lock washers and nuts.

6. Check to make sure the rail is centered over the

door (or in line with the header bracket if the

bracket is not centered above the door).

7. Remove the 2x4. Operate the door manually. If

the door hits the rail, raise the header bracket.

HARDWARE SHOWN ACTUAL SIZE

I I I I I I I I I IILILI

Lag Screw

5/16"-18xl -7/8"

@

Hex Screw

5/18"- 18x7/8" Nut 5/18"-18 Lock Washer 5/16"

Toavoid possible SERIOUSINJURYfrom afalling

garage door opener,fasten it SECURELYto structural

supports of the garage.Concreteanchors MUSTbe used

if installing any brackets into masonry.

Figure 1 Structural

Supports

\\

Measure >

Distance ,

i

Lag Screws

5/16"-18xl -7/8"

5/16"-18x7/8" Screw

5/16" Lock Washer

5/16"-18 Nut

Figure 2

Bracket / (Not Provided)

(Not Provided) 5/16"-18x7/8" Screw

_ 5/16" Lock Washer

5/16"-18 Nut

5/16" Lock Washer

5/16"-18 Nut

17

iNSTALLATiON STEP 6

install the Door Control

Locate door control within sight of door, at a minimum

height of 5 feet where small children cannot reach,

away from moving parts of door and door hardware.

If installing into drywall, drill 5/32" holes and use the

anchors provided. For pre-wired installations (as in new

home construction), it may be mounted to a single gang

box (Figure 2). NOTE: After installation, a green

indicator light behind the cover will indicate proper

connection. If not lit, the Lock and Light features will not

function (reverse wires to correct).

1.Strip 1/4" of insulation from one end of bell wire and

connect to the two terminal screws on back of door

control by color: white to W and white/red to R.

2. Remove the push bar cover by gently prying off the

top edge with a coin or screwdriver. Fasten with

6ABx1=1/4" self-tapping screws (standard installation)

or 6-32x1" machine screws (into gang box) as follows:

• Install bottom screw, allowing 1/8" to protrude above

wall surface.

• Position bottom of door control on screw head and

slide down to secure. Adjust screw for snug fit.

• Drill and install top screw with care to avoid

cracking plastic housing. Do not overtighten.

• Insert top tabs and snap on cover.

3. (For standard installation only) Run bell wire up

wall and across ceiling to motor unit. Use insulated

staples to secure wire in several places. Be careful

not to pierce wire with a staple, creating a short or

open circuit.

4. Connect the bell wire to the terminal screws on the

motor unit panel: white to 2; white/red to 1.

5. Position the antenna wire as shown.

6. Use tacks or staples to permanently attach

entrapment warning label to wall near door control,

and manual release/safety reverse test label in a

prominent location on inside of garage door.

DO NOT connect power and operate opener at

this time. The trolley will travel to the full open

position but will not return to the close position

until the sensor beam is connected and properly

aligned.

HARDWARE SHOWN ACTUAL SIZE

_ IIlllMIMlllllllllIIIIIll]>

6AB x 1-1/4" Screw

(standard installation)

6-32 x 1" Screw

(pre-wired installation)

Dry Wall Anchors

Insulated

Staples

Lock

Lighted

Push Bar

Light

Sutton

PASSIVEINFRARED

CONTROLCONSOLE

TopreventpossibleSERIOUSINJURYor DEATHfrom

electrocution:

• Besurepoweris notconnectedBEFOREinstallingdoor

control.

• ConnectONLYto 24 VOLTlowvoltagewires.

TopreventpossibleSERIOUSINJURYor DEATHfrom a

closing garagedoor:

• Installdoor control within sight ofgaragedoor,out of

reachof childrenat a minimum heightof 5 feet,and away

from all moving parts of door.

• NEVERpermitchildrento operateor playwith doorcontrol

pushbuttonsor remotecontrol transmitters.

• Activatedoor ONLYwhenit canbe seenclearly,isproperly

adjusted,and thereare no obstructionsto door travel.

• ALWAYSkeepgaragedoor in sight until completelyclosed.

NEVERpermitanyoneto crosspathof closing garagedoor.

i Outside Keylock Accessory ConnectionsTo opener terminal screws: white to 2; white/red to 1

Figure 1

STANDARD WALL MOUNT

To Replace

Insert Top

Tabs First .-

Indicator Switch

Light Push Bar Cover T °N

OFF

Figure 2

PRE-WIRED INSTALLATION

24 Volt

2-Conductor

Bell Wire in

Gang Box

To Replace,

Insert

TOsP qlabt s

Detector ION

I Switch OFF

Light Push Bar Cover

Top

Mounting

Hole

BACK VIEW

Bell

Wire

Terminal

Screws

Bottom

Mounting

Hole

Opener

Terminal Screws

Antenna

18

iNSTALLATiON STEP 7

Install the Light and Lens

• Install a 75 watt maximum light bulb in the socket.

The light will turn ON and remain lit for

approximately 4-1/2 minutes when power is

connected. Then the light will turn OFF.

• Apply slight pressure on the sides of the lens and

slide the tabs into the slots in the end panel. (See

illustration.)

• For convenience, the lens may be installed

after Adjustment Step 4 on page 30.

• To remove, reverse the procedure. Use care to

avoid snapping off lens tabs.

• Use standard neck Garage Door Opener bulbs for

replacement.

Light

Lens

' Lens

Slot

75 Watt Max.

Light Bulb

Lens

Tab

Lens

Guide

iNSTALLATiON STEP 8

Attach the Emergency Release

Rope and Handle

• Thread one end of the rope through the hole in the

top of the red handle so "NOTICE" reads right side

up as shown. Secure with an overhand knot at

least 1" from the end of the rope to prevent

slipping.

• Thread the other end of the rope through the hole

in the release arm of the outer trolley.

• Adjust rope length so the handle is 6 feet above

the floor. Secure with an overhand knot.

NOTE: If it is necessary to cut the rope, heat seal

the cut end with a match or lighter to prevent

unra veling.

. Toprevent possible SERIOUSINJURYor DEATHfrom

a falling garagedoor:

- If possible, useemergencyreleasehandleto

disengagetrolley ONLYwhen garagedoor is

CLOSED.Weakor brokensprings or unbalanced

door could result in an open door falling rapidly

and/or unexpectedly.

- NEVERuse emergencyreleasehandle unless garage

doorway is clearof persons and obstructions.

. NEVERuse handle to pull door open or closed. If rope

knot becomesuntied, you could fall.

Trolley

Emergency ..................l_ _ Overhand

E_ Knot

Release Handle )_

19

iNSTALLATiON STEP 9

Electrical Requirements

To avoid installation difficulties, do not run the

opener at this time.

To reduce the risk of electric shock, your garage door

opener has a grounding type plug with a third

grounding pin. This plug will only fit into a grounding

type outlet. If the plug doesn't fit into the outlet you

have, contact a qualified electrician to install the

proper outlet.

RIGHO WRONG

If permanent wiring is required by your local

code, refer to the following procedure.

To make a permanent connection through the 7/8"

hole in the top of the motor unit:

• Remove the motor unit cover screws and set the

cover aside.

• Remove the attached 3-prong cord.

• Connect the black (line) wire to the screw on the

brass terminal; the white (neutral) wire to the

screw on the silver terminal; and the ground wire

to the green ground screw. The opener must be

grounded.

• Reinstall the cover.

Toprevent possible SERIOUSINJURYor DEATHfrom

electrocution or fire:

. Be sure power is not connectedto the opener,and

disconnect powerto circuit BEFOREremoving cover to

establish permanentwiring connection.

. Garagedoor installation and wiring MUSTbe in

compliancewith all local electricaland building codes.

. NEVERuse an extension cord, 2-wire adapter,or

changeplug in anyway to make it fit outlet. Besure

the opener is grounded.

PERMANENT WIRING

CONNECTION

Ground Tab

Green

Ground Screw

Black

Ground Wire Wire

White Wire Black Wire

2O

Page is loading ...

Craftsman 13953976SRT Owner's manual

This manual is also suitable for

Craftsman 13953976SRT Owner's manual

in other languages

Related papers

Other documents