Oreck XL2000HH User manual

Brand: Oreck

Model: XL2000HH

Category: Vacuum cleaners

Type: User manual

This manual is also suitable for

USER’S GUIDE

•IMPORTANT•

SAVE THIS BOOKLET!

COMMERCIAL

XL2000HH

XL2000RH

XL2000RS

HIGH SPEED UPRIGHT V

ACUUM

CLEANER WITH

CLEANING SYSTEM

SIMPLY AMAZING

Includes:

• Safety Warnings

• Warranty

• Operating Instructions

• Trouble Diagnosis

• Accessories

ENGLISH

FRANÇAIS

GUIDE D’UTILISATION PAGE 8

ESPAÑOL

GUIA DEL USUARIO PAGE 14

When using an electrical appliance, basic

precautions should always be followed,

including the following:

READ ALL INSTRUCTIONS BEFORE

USING THIS VACUUM CLEANER

WARNING

To reduce the risk of fire,

electric shock, or injury:

IMPORTANT

SAFETY INSTRUCTIONS

• Do not leave appliance unattended when plugged in. Unplug

from outlet when not in use and before servicing.

• Do not use outdoors or on wet surfaces.

• Do not operate the unit while in the upright and locked position.

• Do not let the unit run while in any one stationary position for any

period of time. Keep the unit moving while in operation.

• Do not allow to be used as a toy. Close attention is necessary

when used by or near children.

• Use only as described in this manual. Use only manufacturer’s

recommended attachments.

• Do not use with damaged cord or plug. If appliance is not

working as it should, has been dropped, damaged, left outdoors,

or dropped into water, return it to a service center or call

customer service at:

Commercial: 1-800-242-1378

Hospitality: 1-888-23-ORECK

Canada: 1-

866-74-ORECK

• Do not pull or carry by cord, use cord as a handle, close door on

cord, or pull cord around sharp edges or corners. Keep cord

away from heated surfaces.

• Do not run appliance over cord.

• Do not unplug by pulling on cord. To unplug, grasp the plug, not

the cord.

• Do not handle plug or appliance with wet hands.

• Do not put any object into openings. Do not use with any opening

blocked; keep free of dust, lint, hair and anything that may reduce

air flow

•

Keep hair

, loose clothing, fingers and all par

ts of body away fr

openings and moving parts.

• Do not use to pick up anything that is burning or smoking, such as

cigarettes, matches, or hot ashes.

• Do not use without filter bag assembly in place.

• Turn off all controls before unplugging.

• Use extra care when cleaning on stairs.

•

Do not use to pick up flammable or combustible liquids, such as

gasoline or lighter fluid, or use in ar

eas wher

e they may be

present.

• Do not use appliance in an enclosed space where flammable,

explosive or toxic vapors are given off by oil base paint, paint

thinner, some mothproofing substances, or in an area where

flammable dust is present.

• Do not pick up toxic material such as chlorine bleach, drain

cleaner

, gasoline, etc. with this appliance.

•

Use caution when vacuuming over ar

ea r

ug edges and

fringe.

SAVE THESE INSTRUCTIONS

For Commercial Use

ENGLISH

Table of Contents

BEFORE OPERATING

CLEANER, READ ALL

INSTRUCTIONS IN THIS

MANUAL CAREFULLY.

Maintenance and Customer Service,

Important Safety Instructions . . . . . . . . page 2

Warranty,

Troubleshooting Guide . . . . . . . . . . . page 3

Assembly,

Operating Instructions . . . . . . . . . . . . page 4

Operating Instructions cont.,

To Replace Paper Filter Dust Bag . . . page 5

How to Replace a Worn Belt,

Stuffing or Blockage . . . . . . . . . . . . . page 6

Using an Oreck Fresh Air

Tab,

Grounding Instructions,

To Adjust or Replace Brush . . . . . . . . page 7

Français Guide D’utilisation . . . . page 8

Español Guia Del Usuario . . . . . . page 14

Your ORECK vacuum cleaner is a product of precise engineering.

The motor bearings are permanently lubricated and should not be

oiled. If you require additional information or have problems with

your ORECK appliance, you may call ORECK commercial customer

service at:

Commercial: 1

800

242-1378

Hospitality: 1-888-23-ORECK

Canada: 1-866-74-ORECK

Please specify the model number and serial/code number which

can be found on the data plate on the back of the vacuum.

Save your sales or purchase slip. Should your ORECK appliance

require warranty service in the U.S.A., present this slip to the

Authorized Ser

vice Center as your pr

oof of pur

chase date or

, in

Canada, call customer ser

vice.

Maintenance and

Customer Service

Accessories

Sold Separately

Commercial: 1-800-242-1378

Hospitality: 1-888-23-ORECK

Canada: 1-866-74-ORECK

ITEM PART #

1. Dust Bag, 25 Pack, Saniseal

ACDS Hypo-Allergenic PK800025DW

Dust Bag, 25 Pack, Regular

PK800025

2. Belts, 3 Pack 0300604

3. Oreck Fresh Air

Tabs AIRTABS

ENGLISH

Warranty

ORECK MANUFACTURING COMPANY: (Oreck gives you the

following limited warranty for this product only if it was originally

purchased for use, not resale, from Oreck or an Oreck Authorized

Retail Dealer.)

Oreck will repair or replace, free of charge, to the original

purchaser, any part which is found to be defective in material or

workmanship within one (1) year of the date of pur

chase. This

limited warranty covers the revolving roller brush for thirty (30)

days for commercial use only.

This limited warranty does not cover the replacement of

expendable or consumable parts such as carbon motor brushes,

edge brushes, drive belts, bulbs, disposable bags and other parts

subject to normal wear unless they are defective in material or

workmanship.

This limited warranty does not apply to any part subjected to

accident, abuse, or alteration, misuse, damage caused by fire or

act of God, the use of voltages other than indicated on the serial

number plate of this product or service of this product by other than

Oreck or an Oreck Factory Authorized Service Center.

Oreck does not authorize any person or representative to assume

or grant any other warranty obligation with the sale of this

product.

Oreck’s limited warranty is valid only if you retain proof of

purchase from Oreck or an Oreck Authorized Retail Dealer for this

product. If you purchase this product from any other source, your

purchase is “AS IS,” which means Oreck grants you no warranty,

and that you, not Oreck, assume the entire risk of the quality and

performance of this product, including the entire cost of any

necessary servicing or repairs of any defects.

Oreck’s liability for damages to you for any costs whatsoever

arising out of this statement of limited warranty shall be limited to

the amount paid for this product at the time of original purchase,

and Oreck shall not be liable for any direct, indirect, consequential

or incidental damages arising out of the use or inability to use this

product.

Some states do not allow the exclusion or limitation of incidental

or consequential damages, so the above limitation or exclusion

may not apply to you.

ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT,

INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A P

ARTICULAR PURPOSE, ARE LIMITED IN

DURATION TO THE WARRANTY PERIOD, AND NO

WARRANTIES, WHETHER EXPRESS OR IMPLIED, WILL APPLY

AFTER THIS PERIOD.

Some states do not allow limitations on the duration of implied

warranties, so the above limitation may not apply to you.

This war

ranty gives you specific legal rights, and you may also

have other rights which vary from state to state.

SAVE SERVICE CALLS...CHECK THESE FIRST:

•

Is the disposable filter dust bag full?

• Are pores of filter dust bag clogged with powder or fine dust?

• Is anything clogging the revolving brush, lower tube, intake

opening, fan housing or connector assembly opening?

• Is the belt in place and turning the brush?

• Are the brush ends in the proper location?

•

Does the brush turn freely? Are hair, string or rug fibers wound

around the brush?

Troubleshooting Guide

CLEANER

WILL NOT RUN

CLEANER

DOES NOT PICK UP

Not plugged in

properly.

No electricity in

wall outlet.

Filter bag is full.

Nozzle or intake

pivot clogged.

Belt is broken or

stretched.

Brush is worn.

Tube clogged.

Bag pores are

clogged with fine

dust.

Impeller fan is

broken.

Revolving brush is

not even at both

ends.

Be sure cleaner is

firmly plugged

into wall outlet.

Check electrical

source–fuse or

circuit breaker.

Replace filter bag.

See “To Install

Paper Filter Dust

Bag.”

Clear obstruction.

Replace belt.

See “To Replace

or Adjust Brush. ”

Clear obstruction.

Change bag.

Retur

n to Ser

vice

Center for r

epair

Check br

ush roll

end cards. Make

sure words “old”

or “new” match at

each end.

PROBLEM POSSIBLE SOURCE AREAS TO CHECK

Whenever calling, please be sure to have your model and

serial number fr

om data plate.

CALL COMMERCIAL CUSTOMER SERVICE HOT LINE

Commercial: 1-800-242-1378

Hospitality: 1-888-23-ORECK

Canada: 1-866-74-ORECK

ALL OTHER SERVICING SHOULD BE DONE BY AN

ORECK AUTHORIZED SERVICE CENTER.

WARNING: Unplug cord from

electrical outlet before servicing.

ENGLISH

Operating Instructions

To Operate

Make sure disposable paper filter dust bag is in place. DO NOT

operate the cleaner without a paper filter dust bag. Plug the

power cord into an electrical outlet and press the

ON (l) - OFF

(O) switch on Helping Handle Assembly, or on top of base for

Straight Handle Models when ready to operate.

General Information

The performance of your new cleaner greatly depends upon care

and maintenance. The instructions in this manual will guide you in

performing basic care and maintenance. To obtain the most

satisfying years of service read the instructions and keep them

handy for future reference.

Operating Recommendations

This new ORECK XL High-Speed Upright is one of the finest,

fastest, and strongest units in its class. You’ll love the way it

cleans, gets under things, and it’s SO lightweight and easy to

use.

The following ar

e a few simple suggestions r

egar

ding its

operation:

1. When inserting a new disposable paper filter dust bag—

FIRST PUFF OUT and OPEN THE BAG.

2. When the disposable filter dust bag is full, REPLACE IT.

3. If at any time the machine does not pick up properly or

makes an unusual noise, STOP OPERA

TION and service.

4. Although your upright will pick up pins, paper clips, and

other small objects, it is recommended that these be

emoved fr

om the floor befor

e you vacuum. Failur

e to do so

may r

esult in per

manent damage to the motor suction fan

and its housing.

WARNING: Do not use your vacuum cleaner on damp or

wet surfaces. This will cause damage to the vacuum cleaner

and is dangerous to the user. Damage caused by use on wet

or damp surfaces is not covered under warranty.

6. REPLACE THE BELT EVERY 6 MONTHS.

Assembly

o assist you in identifying

components of your vacuum,

the parts have been numbered

as follows

1 Handle section, upper

2 Tube, lower

3 Power head

4 Outer bag

5 Paper filter dust bag

6 Power cord

7 Retaining spring

8 Bag tension bar

9 Zip fastener

10 On/off switch

11 Cord hook

12 Plastic loop/

cable clamp

13 Connector assembly

14 Fan housing

15 Cord assembly

Before assembling appliance,

remove two screws from the

connector assembly. Remove

car

dboar

d inser

t by pulling

upward.

With ON/OFF switch facing

the front of the unit, slide

upper handle section over

matching section of the

connector assembly. Place

brace against handle and

connection assembly aligning

the holes. Insert short screw

into top hole and long screw

into the bottom hole then

tighten firmly until handle is

no longer loose.

Upper

Handle

Connector

Assembly

Attach cord to cord clip by

pressing cord above and

below clip ensuring the cord

is fully rested in clip.

ENGLISH

7. Change the disposable filter dust bag at least once a

month—even if it is not full! The collected dust in the dust

bag can cause odor, attract moisture, act as a breeding

area and can affect the efficiency of the cleaner.

DO NOT run the vacuum cleaner over cord. The revolving

brush could damage the cord.

Use caution when vacuuming over area rug edges & fringe.

Disposable Paper Filter Dust Bags

Disposable paper filter dust bags play a very important role in

the efficiency of your ORECK vacuum cleaner. The purpose of

the filter bag is to trap dirt, but at the same time it must be

porous enough to allow air to pass through. If the filter bag

becomes clogged, no air can pass through the cleaner and

cleaning cannot take place, regardless of the cleaner’s power.

Incr

ease the CLEANING POWER of your cleaner by changing

the bag often.

To keep your cleaner operating at maximum efficiency, change

the dust bag frequently. DO NOT FILL ABOVE THE LINE

INDICATED ON THE DUST BAG.

Be sure the disposable paper filter dust bag is installed properly.

All paper dust bags are not the same. Your ORECK disposable

dust bags have been designed to be used with the ORECK

cleaner. Using bags other than genuine ORECK disposable bags

will affect the cleaning ability of your cleaner and could cause

damage to it.

The Belt

The belt on your vacuum cleaner controls the speed of the

revolving brush and is very important for the effective operation

of the cleaner. If the belt becomes stretched or cut, it will cause

the revolving brush to stop completely or slow down. See

instructions in the manual for replacing belt.

An extra belt is stored in the baseplate of your cleaner. When

buying replacement belts, use ONLY ORECK genuine belts. Belts

other than ORECK belts will not operate the revolving brush

correctly and may create undue stress which will cause damage

to the motor and brush bearings. Using belts other than ORECK

belts will void the warranty.

Lubrication

The vacuum cleaner motor bearings are factory lubricated and

sealed. Further lubrication is not required.

General Cleaner Care

At least once a month, check for

and remove excessive lint, string

or hair from revolving brush.

ipe the outside of the cleaner

with a damp cloth. Also, clean

the connector deflector assembly

area, base of cleaner and fan

housing area. If there is dust in

the outer bag, vacuum it or

shake it out.

A little preventative maintenance

will keep your cleaner looking

new and will ensur

e continued

cleaning ef

fectiveness.

CAUTION—Wood Floors, Soft (Vinyl, Asphalt Tile, etc.)

Floor Surfaces and Polished Floor Finishes

Use floor and floor finish manufactur

er’

s r

ecommended methods

of cleaning. The metal strip on the base of the cleaner could be

damaged if used on concrete or abrasive surfaces, and,

therefore, cause damage to wood floors, soft (vinyl, asphalt tile,

etc.) floor surfaces and polished floor finishes. The roller brush

may also scuff very soft finishes. Do not operate the unit while in

the upright and locked position. Do not let the unit r

un while in

any one stationary position for any period of time. Keep the unit

moving while in operation.

Celoc® Hypo-Allergenic Filter System

The CELOC SMMS outer bag of your vacuum cleaner is high

filtration medical material designed to filter the smallest of dust

particles. It is important the inside of the outer bag be cleaned.

Turning the outer bag inside out, vacuum the inside of the outer

bag or hand wash with war

m water and then let the bag air

y. For best results, the CELOC SMMS outer bag should be

replaced once a year.

The CELOC layered disposable inner

dust bag must be replaced once a month even if it is

not full.

Change it more often if it is used in extremely dirty areas.

Increase the cleaning power of your vacuum by changing the

bag often.

To Replace Filter

Dust Bag

BAG INSTALLATION:

1. Hook bottom of bag collar

opening under lip “B” of

connector assembly. Pull up

on bag collar and snap over

lip “A” of connector.

2. Press on edges of bag collar

to insure bag is completely

installed.

IMPORTANT: Check to

make sure bag collar is

behind lips “A” and “B”.

If it is not, dust will leak into

outer bag. When filter bag

is in place, close outer bag

with zipper fastener.

WARNING: Unplug cord from

electrical outlet before servicing.

ENGLISH

WARNING: Unplug cord from

electrical outlet before servicing.

Remove the replacement

belt from the storage

channel.

Remove the door by

removing the hold down

screw located on side of

power head.

Slide the door forward

by prying open with a

screwdriver or coin.

Remove the belt from the

brush roll pulley and the

motor drive shaft.

Loop the new belt over

the motor drive shaft.

Place the opposite end of

the belt on the br

ush r

oll

pulley.

Rotate the brush roll three

(3) complete revolutions

to ensur

e that no par

t of

the belt is over

hanging

the end of the motor

drive shaft.

Replace the door by

sliding it into the gr

oove

at the bottom of the

housing. Replace the

hold down scr

WARNING: Unplug cord from electrical

outlet before servicing.

Stuffing or Blockage

Under cer

tain conditions it is possible to stuff or block the intake

tube and the lower tube assembly. If your vacuum cleaner does

not pick up properly, or makes unusual noise and the outer bag

does not fluf

f up or balloon open, follow the following steps:

How to Replace a Worn Belt

1. Check for blockage at the

mouth of the intake

opening. See illustration A.

If there is blockage, remove

it with long-nose pliers, a

screwdriver or coat hanger.

If you can not reach the

blockage, remove

baseplate. See illustration B.

2. If the blockage is not at the

base, remove lower tube.

See illustration C. Unhook

retainer spring, releasing

bottom of bag. Twist lower

collar counterclockwise to

slide up. Pull tube out of

base. Check for blockage. If

blockage is in the tube,

remove with a coat hanger.

3. If tube is not blocked, look

into fan housing. See illus-

tration D. Remove debris

with long-nose pliers, a

screwdriver or coat hanger.

4. To reassemble, check O-ring

on tube, and replace if

damaged. Vacuum will not

operate properly without the

tube O-ring. Slide O-ring to

appr

oximately 2" fr

om base

of tube. Replace tube by

first lining up slot at base of

tube with inner tab inside

fan housing. Then reinsert

tube and push down until

the tube is seated. Make

sure O-ring is in place

against fan housing

opening. Replace and

tighten collar until collar

locking tabs ar

e locked in

place. See illustration E.

Make sure collar is not cross

thr

eaded on housing.

Intake Opening

O-ring

Fan

Housing

Intake Opening

Retainer

Spring

Rotate and match

bearing assemblies

IMPORTANT: On plush and new carpets, stuffing may occur

due to excessive fuzz and loose cuttings in the carpet.

Stuffing could occur for the first few cleanings until all the

loose material is removed. Due to the high efficiency of the

cleaner, many older carpets will cause stuffing when the

cleaner is first used on them.

NOTE: If the above actions do not correct the problem, contact

ORECK authorized service center or call the commercial

customer service center.

Commercial: 1-800-242-1378

Hospitality: 1-888-23-ORECK

Canada: 1-866-74--ORECK

Your ORECK XL vacuum cleaner has a

special FRESH AIR tab pocket. This

pocket is located inside the outer bag

in the area where the disposable

paper bag attaches to the intake tube.

Insert tablet in pocket.

Using An Oreck Fresh Air

Tab

5. Many times blockage occurs

due to a full dust bag

causing dirt to back down

the air flow system. When

that happens, the blockage

will be at the top of the

system, starting in the area

wher

e the dust bag connects

to the connector assembly.

See illustration F.

WARNING: Unplug cord from

electrical outlet before servicing.

To determine if the brush is

wor

n, place a firm straight

edge across the nozzle

opening. If brush bristles

do not extend beyond

baseplate, brush should be

adjusted.

Remove the baseplate by

removing 5 screws. Then,

remove the belt and brush

roll from the housing.

Rotate both bearing

assemblies at ends of

brush roll to show “OLD”

and replace in the holding

channels in the housing.

NOTE: The bearing

assembly setting marked

“OLD” has two notches

(

l l ) on the top of the

assembly. The one marked

“NEW” has one notch

( l ). When rotating

bearings, make sure both

bearing assembly settings

are the same and face up

when replacing the brush

roll.

Reassemble the belt and

the baseplate and check

bristle height above

baseplate at each end of

brush.

If a previous adjustment

has already been made

and bristle height does not

extend above baseplate, a

new brush assembly

should be or

der

ed.

IMPOR

ANT: Unless

the brush is worn as

indicated above,

both bearings must

be in the “NEW”

position. When

rotating, both

bearings must be in

the “OLD” position.

Unmatched settings

will cause damage

to your machine.

ENGLISH

To Adjust or Replace Brush

This appliance must be grounded. If it should malfunction or

break down, grounding provides a safe path of least resistance

for electrical current, reducing the risk of electric shock. The cord

for this appliance has an equipment-grounding conductor and a

grounding plug. It must only be plugged into an electrical outlet

that is properly installed and grounded in accordance with all

local codes and ordinances.

DANGER: Improper connection of the equipment-grounding

conductor can result in a risk of electrical shock. Check with a

qualified electrician or service person if you are in doubt as to

whether the outlet is grounded. If not, have a proper outlet

installed by a qualified electrician.

This appliance is for use on a nominal 120-volt circuit. It has a

grounding plug similar to the example shown. Make sure the

appliance is connected to an outlet with the same configuration

as the plug. No adapter should be used with this appliance.

Grounding Pin

ounded Outlet

Grounding Instructions

Connector

Deflector

Opening

Page is loading ...

Oreck XL2000HH User manual

Brand: Oreck

Model: XL2000HH

Category: Vacuum cleaners

Type: User manual

This manual is also suitable for

Download PDF

report

in other languages

français: Oreck XL2000HH Manuel utilisateur
español: Oreck XL2000HH Manual de usuario

Oreck XL2000HH User manual

This manual is also suitable for

Oreck XL2000HH User manual

in other languages

Related papers

Other documents