Mode ND BC20 PA Installation guide

Brand: Mode

Model: ND BC20 PA

Category: Car video systems

Type: Installation guide

Fig. 12-2

Abb. 12-2

Fig. 12-3

Abb. 12-3

Fig. 12-1

Abb. 12-1

Fig. 12-4

Abb. 12-4

PIONEER CORPORATION

4-1, MEGURO 1-CHOME, MEGURO-KU, TOKYO 153-8654, JAPAN

PIONEER ELECTRONICS (USA) INC.

P.O. Box 1540, Long Beach, California 90801-1540, U.S.A.

TEL: (800) 421-1404

PIONEER EUROPE NV

Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium

TEL: (0) 3/570.05.11

PIONEER ELECTRONICS ASIACENTRE PTE. LTD.

253 Alexandra Road, #04-01, Singapore 159936

TEL: 65-6472-7555

PIONEER ELECTRONICS AUSTRALIA PTY. LTD.

178-184 Boundary Road, Braeside, Victoria 3195, Australia

TEL: (03) 9586-6300

PIONEER ELECTRONICS OF CANADA, INC.

300 Allstate Parkway, Markham, Ontario L3R 0P2, Canada

TEL: 1-877-283-5901

PIONEER ELECTRONICS DE MEXICO, S.A. de C.V.

Blvd. Manuel Avila Camacho 138 10 piso

Col. Lomas de Chapultepec, Mexico, D.F. 11000

TEL: 55-9178-4270

Published by Pioneer Corporation.

Publié par Pioneer Corporation.

Printed in Japan

Imprimé au Japon

<CZR5092-A> E<KKNNX> <07D00000>

Digital Parking Assistance Camera

Caméra numérique d’assistance au parking

Installation Manual

Manuel d’installation

ND-BC20PA

① Glass surface

② Make sure it doesn’t touch the wiper

③ Install on the center part

Fig. 1

Abb. 1

𝖠 Rear view camera × 1 𝖢 Image processing

unit power supply × 1

𝖡 RCA power supply cable × 1

𝖤 Hexagon wrench × 1 𝖥 Velcro tape

(soft type) × 1

𝖦 Velcro tape

(hard type) × 1

𝖩 Waterproof pad × 1𝖨 Plastic clamp × 10

𝖪

Double-sided tape (rectangular) × 1

③ Camera stand

⑤ Camera stand

① Turn

② Twist

① Camera

stand

② When sticking to the center

④ Installation

screw

③ Bottom

① Top

② Bottom

① Top

Fig. 5

Abb. 5

Fig. 7

Abb. 7

Fig. 8

Abb. 8

Fig. 6

Abb. 6

② Rear view

camera

Fig. 9

Abb. 9

Fig. 10

Abb. 10

③ Bumper or rear edge of car

① Image processing unit

power supply

② Velcro tape

(hard type)

③ Velcro tape

(soft type)

Fig. 11

Abb. 11

Fig. 13

Abb. 13

Fig. 15

Abb. 15

① Angle of view

Horizontal: 135°

② Angle of view

Vertical: 100°

𝖫 Double-sided tape (square) × 1

𝖡

𝖠

Fig. 2

Abb. 2

Fig. 3-1

Abb. 3-1

Fig. 3-2

Abb. 3-2

Fig. 3-3

Abb. 3-3

Fig. 3-4

Abb. 3-4

③ Mark

③ When attaching using camera stand bracket 𝖢

(attaching while rotating by 90°)

𝖣 Button unit × 1

𝖧 Metal clamp × 5

𝖬 Camera stand bracket 𝖢 × 1

Fig. 4

Abb. 4

Fig. 14

Abb. 14

① Double-sided tape (square)

② Button unit

③ Metal

clamp

Parts supplied

𝖠 Rear view camera × 1

𝖡 RCA power supply cable × 1

𝖢 Image processing unit power supply × 1

𝖣 Button unit × 1

𝖤 Hexagonal wrench × 1

𝖥 Velcro tape (soft type) × 1

𝖦 Velcro tape (hard type) × 1

𝖧 Metal clamp × 5

𝖨 Plastic clamp × 10

𝖩 Waterproof pad × 1

𝖪 Double-sided tape (rectangular) × 1

𝖫 Double-sided tape (square) × 1

𝖬 Camera stand bracket 𝖢 × 1

Installation example (Fig. 1)

① Glass surface

② Make sure it doesn’t touch the wiper

③ Install on the center part

Note:

• The position and angle of the image from the rear

view camera can still be adjusted using the initial

setup even if the camera is not installed in the

center of the vehicle. Refer to “First Time Setup”

in the Owner’s Manual for details.

Changing the orientation of camera

stand installation (Fig. 12-1)

The camera stand can be installed in

various ways by changing the direction in

which camera stand bracket 𝖡 is attached

or attaching camera stand bracket 𝖢.

Change to match your car’s shape or the

installation site.

1. Use the hexagon wrench to remove

the screws securing camera stand

brackets 𝖠 and 𝖡. (Fig. 2)

2. Change the direction of installation

bracket 𝖡. (Fig. 3-1)

3. Reattach with the screws.

Installing Using Camera Stand Bracket 𝖢

(Fig. 12-4)

1. Use the hexagon wrench to remove

the screws securing camera stand

brackets 𝖠 and 𝖡. (Fig. 2)

2. Attach camera stand bracket 𝖢 to

the camera stand. (Fig. 3-2)

3. Attach the rear view camera to cam-

era stand bracket 𝖡. (Fig. 3-3)

4. Attach the camera stand and rear

view camera. (Fig. 3-4)

Route the cables as shown in the figure so

that they do not become entangled.

Attach the camera stand while being

careful not to mistake the vertical

orientation

of the rear view camera. (Fig. 8)

Installation Procedure

Note:

• Before making a final installation of the unit,

temporarily connect the wiring to confirm that

the connections are correct and the system works

properly.

• Use only the parts included with the unit to ensure

proper installation. The use of unauthorized parts

can cause malfunctions.

• Consult with your nearest dealer if installation

requires the drilling of holes or other

modifications of the vehicle.

• Install the unit where it does not get in the driver’s

way and cannot injure the passenger if there is a

sudden stop, like an emergency stop.

• When mounting this unit, make sure none of

the leads are trapped between this unit and the

surrounding metalwork or fittings.

• To prevent electric shock, do not install the image

processing unit power supply in places where it

might come in contact with liquids.

• Do not mount this unit near the heater outlet,

where it would be affected by heat, or near the

doors, where rainwater might splash onto it.

(Never install in locations such as the above

because of the danger of malfunction due to high

temperatures.)

• Before drilling any mounting holes always check

behind where you want to drill the holes. Do not

drill into the gas line, brake line, electrical wiring

or other important parts.

• If this unit is installed in the passenger compartment,

anchor it securely so it does not break free while the

car is moving, and cause injury or an accident.

• If this unit is installed under a front seat, make

sure it does not obstruct seat movement. Route

all leads and cords carefully around the sliding

mechanism so they do not get caught or pinched

in the mechanism and cause a short circuit.

• Locate in the position you want to install the rear

view camera. Adjust the angle of the rear view

camera, and install so that the camera doesn’t

touch the car.

• When sticking to a glass surface, stick it on in a

position that assures the camera doesn’t touch the

rear window.

Installation <ENGLISH>

• Install so that it does not obstruct the rear field of

view.

• Install so that it does not protrude from the side of

the car.

• Do not perform installation in rain or fog.

• When humidity is high, dry the surface to which

the unit is to be attached before installing. Moisture

on the attachment surface reduces adhesive strength

which may lead to the unit coming off.

• Install so that the rear view camera is aligned in

parallel with the direction of vehicle movement

(straight back from the vehicle). (Fig. 4)

• Install the rear view camera above the license plate.

If the installed location of the rear view camera is

lower than the license plate, it will not be possible

to make image corrections causing distortion of the

image from the rear view camera.

• If the temperature of the attachment surface is

low, warm with a hair dryer of other means before

installing to improve adhesive strength.

• Do not attach the camera stand to areas on the car

body treated with fluorocarbon resin, or glass. This

may result in the rear view camera falling off.

• During the 24-hour period after installing:

– Do not apply water to the unit.

– Do not expose the unit to rain.

– Do not subject the camera to unnecessary force.

• Thoroughly clean where tape is used for sticking

on the unit.

1. Clean the surface to which the rear

view camera is to be installed.

(Fig. 5)

Use a cloth or other item to wipe oil, wax,

dust and any other dirt from the installation

surface.

2. Remove the rear view camera from

the camera stand. (Fig. 6)

Remove the mounting screws with the

hexagon wrench provided.

① Top

② Rear view camera

③ Bottom

④ Installation screw

⑤ Camera stand

3. Align the camera stand with the

installation surface. (Fig. 7)

Adjust the camera stand so that there is no

space between it and the installation surface.

① Turn

② Twist

③ Camera stand

4. Attach the camera stand removed in

step 2 to the rear view camera with

the mounting screws. (Fig. 8)

The rear view camera has a mark indicating

the top of the camera.

Attach the camera stand while being

careful not to mistake the vertical

orientation of the rear view camera.

① Top

② Bottom

③ Mark

5. Peel off the sheet on the back of they

camera stand and stick it on. (Fig. 9,

Fig. 10)

Press the camera stand with your fingers to

stick it to the installation surface. Touching

the adhesive surface or sticking the unit

on a second time reduces adhesive power

which may result in the unit coming off.

① Camera stand

② When sticking to the center

③ When attaching using camera stand bracket

𝖢 (attaching while rotating by 90°)

6. Adjust the angle so that the bumper

or rear edge of the car is displayed

at the bottom of the TV screen.

(Fig. 11, Fig. 12-2, Fig. 12-3, Fig. 13)

① Angle of view

Horizontal: 135°

② Angle of view

Vertical: 100°

③ Bumper or rear edge of car

Note:

• The angle shown varies according to the camera

specifications. The actual angle is narrower as a

result of image processing.

• The position and angle of the image from the

rear view camera can still be adjusted using the

initial setup even if the bumper or rear edge of

the car is not displayed on the bottom of the TV

screen. Refer to “First Time Setup” in the Owner’s

Manual for details.

7. Attach the image processing unit

power supply. (Fig. 14)

Affix the Velcro tape (hard type) to the

bottom of the image processing unit power

supply, and affix the Velcro tape (soft type)

to the mounting location.

① Image processing unit power supply

② Velcro tape (hard type)

③ Velcro tape (soft type)

• You can use Velcro tape (hard type) to attach

directly to a carpet, but do not use the soft type.

• Install the image processing unit power sup-

ply close enough for the rear view camera

cable to reach.

8. Attach the button unit (Fig. 15).

Affix the double-sided tape (square) to

the backside of the button unit. Next press

the unit onto the location where it will

be mounted. Affix the metal clamp to the

location where the cord is to be and then

secure the cord with the clamp.

① Double-sided tape (square)

② Button unit

③ Metal clamp

Instalación <ESPANÕL>

Piezas suministradas

𝖠 Cámara de vista posterior × 1

𝖡 Cable de suministro de energía RCA × 1

𝖢 Fuente de energía de la unidad de procesa-

miento de imagen × 1

𝖣 Unidad de botones × 1

𝖤 Llave hexagonal × 1

𝖥 Cinta Velcro (tipo blanda) × 1

𝖦 Cinta Velcro (tipo dura) × 1

𝖧 Abrazadera metálica × 5

𝖨 Abrazadera plástica × 10

𝖩 Almohadilla impermeable × 1

𝖪 Cinta de doble cara (rectangular) × 1

𝖫 Cinta de doble cara (cuadrada) × 1

𝖬 Ménsula del soporte de la cámara 𝖢 × 1

Ejemplo de instalación (Fig. 1)

① Superficie de vidrio

② Asegúrese de que no toque el limpiador

③ Instale en la pieza central

Nota:

• Todavía se puede ajustar la posición y el ángulo de la

imagen desde la cámara de vista posterior utilizando

la configuración inicial aunque la cámara no esté

instalada en el centro del vehículo. Para los detalles,

consulte la sección “Configuración por primera vez”.

Cambio de la orientación de la instalación

del soporte de la cámara (Fig. 12-1)

Se puede instalar el soporte de la cámara de

varias formas, cambiando la dirección en

la cual se fija la ménsula del soporte de la

cámara 𝖡, o fijando la ménsula del soporte

de la cámara 𝖢. Cambie de acuerdo con a

la forma de su coche o sitio de instalación.

1. Utilice la llave hexagonal para sacar

los tornillos que fijan las ménsulas 𝖠

y 𝖡 del soporte de la cámara. (Fig. 2)

2. Cambie la dirección de la ménsula

de instalación 𝖡. (Fig. 3-1)

3. Vuelva a fijar con los tornillos.

Instalación utilizando la ménsula del

soporte de la cámara 𝖢 (Fig. 12-4)

1. Utilice la llave hexagonal para sacar

los tornillos que fijan las ménsulas 𝖠

y 𝖡 del soporte de la cámara. (Fig. 2)

2. Fije la ménsula del soporte de la

cámara 𝖢 al soporte de la cámara.

(Fig. 3-2)

3. Fije la cámara de vista posterior a la

ménsula del soporte de la cámara 𝖡.

(Fig. 3-3)

4. Fije el soporte de la cámara y la

cámara de vista posterior. (Fig. 3-4)

Encamine los cables como se muestra en la

figura de modo que no queden enredados.

Fije el soporte de la cámara teniendo

cuidado en no invertir la orientación

vertical de la cámara de vista superior.

(Fig. 8)

Procedimiento de instalación

Nota:

• Antes de la instalación final de la unidad, conecte

el cableado temporalmente y confirme que las

conexiones son correctas y que el sistema trabaja

normalmente.

• Utilice solamente las partes incluídas con la unidad

para asegurar una instalación adecuada. El uso de

partes no autorizadas puede ocasionar fallas de

funcionamiento.

• Si la instalación requiere del taladrado de orificios u

otras modificaciones del vehículo, consulte con su

agente o concesionario más cercano a su domicilio.

• Instale la unidad en donde no interfiera con el

conductor y no pueda lesionar al pasajero en caso

de una parada repentina, tal como una frenada de

emergencia.

• Cuando monte esta unidad, cerciórese que ninguno

de los cables queda aprisionado entre esta unidad y

accesorios o partes metálicas circundantes.

• Para prevenir descargas eléctricas, no instale la fuente

de energía de la unidad de procesamiento de imagen

en lugares donde pueda entrar en contacto con

líquidos.

• No monte esta unidad cerca de la salida del calefactor,

en donde podría ser afectado por el calor o cerca

de las puertas, en donde la lluvia podría salpicar

sobre la misma. (Para evitar el riego de fallos de

funcionamiento producidos por las altas temperaturas,

evite la instalación en los lugares arriba.)

• Antes de taladrar cualquier orificio de montaje

siempre compruebe lo que hay detrás en donde

desea taladrar los orificios. No taladre en la línea

de combustible, cableado eléctrico u otras partes

importantes.

• Si esta unidad es instalada en el compartimiento de

pasajeros, fíjela seguramente de modo que no se

desprenda mientras el automóvil se encuentra en

movimiento, y pueda ocasionar lesiones o accidentes.

• Si esta unidad se instale bajo un asiento delantero,

cerciórese de que no obstruye el movimiento

del asiento. Pase todos los cables y conductores

cuidadosamente a través de los mecanismo

deslizantes, de modo que no queden aprisionados

o atrapados en el mecanismo y ocasionen un corto

circuito.

Page is loading ...

Fig. 16

Abb. 16

Fig. 17

Abb. 17

Fig. 18

Abb. 18

Fig. 19

Abb. 19

① Pull out from here

② Hinge

③ Harness cover

⑤ Hatch

④ Rear view

camera

① Rear view camera

② Hatch

③ Cord

② Waterproof pad

Fig. 20

Abb. 20

① Plastic clamp

③ Rubber packing

④ Make a U-shaped loop in

the lead outside the rubber

packing to prevent rain-

water from flowing along

the lead into the interior

of the vehicle.

Connection <ENGLISH>

Note:

• This unit is for vehicles with a 12-volt battery and

negative grounding. Before installing it in a recreational

vehicle, truck, or bus, check the battery voltage.

• To avoid shorts in the electrical system, be sure to

disconnect the battery cable before beginning

installation.

• Refer to the owner’s manual for details on connecting the

other units, then make connections correctly.

• Secure the wiring with cable clamps or adhesive tape. To

protect the wiring, wrap adhesive tape around them where

they lie against metal parts.

• Route and secure all wiring so it cannot touch any

moving parts, such as the gear shift, handbrake and seat

rails. Do not route wiring in places that get hot, such

as near the heater outlet. If the insulation of the wiring

melts or gets torn, there is a danger of the wiring short-

circuiting to the vehicle body.

• Do not shorten any leads.

• Never feed power to other equipment by cutting the

insulation of the power supply lead of the unit and

tapping into the lead. The current capacity of the lead will

be exceeded, causing over heating.

• When replacing the fuse, be sure to only use a fuse of the

rating prescribed on the fuse holder.

• To minimize noise locate the TV antenna cable, radio

antenna cable and RCA power supply cable as far away

from each other as possible.

• Connection to a TV with an RCA video input is possible,

but confirm whether the TV you use has a reverse gear

connection function.

• If this unit is installed in a vehicle that does not have an

ACC (accessory) position on the ignition switch, the red

lead of the unit should be connected to a terminal coupled

with ignition switch ON/OFF operations. If this is not

done, the vehicle battery may be drained when you are

away from the vehicle for several hours.

ACC position No ACC position

• Cords for this product and those for other products may

be different colors even if they have the same function.

When connecting this product to another product, refer to

the supplied manuals of both products and connect cords

that have the same function.

Connection sample (Fig. 16)

① Image processing unit power supply

② Rear view camera connector

③ RCA power supply cable connector

④ Rear view camera

⑨ Button unit

⑩ Button unit connector

Video input jack

Connect to video input jack.

⑤ RCA pin

Accessory power supply

To electric terminal controlled by ignition

switch (12 V DC) ON/OFF.

⑥ Red

⑦ Fuse (1A)

Ground

To vehicle (metal) body.

⑧ Black

Cord installation (Fig. 17)

① Plastic clamps

② Rear view camera

③ RCA power supply cable

④ Product with a video input jack

(Hideaway unit etc.)

⑤ Image processing unit power supply

⑥ Button unit

⑦ Made with a rasp etc.

⑧ Scuff plate

⑨ Plastic clamp

⑩ Waterproof plate

⑪ Double-sided tape (rectangular)

Cord installation points (Fig. 18)

• When pulling the cord out of the car,

pull from the outer side of the hatch

harness cover and hinge.

① Pull out from here

② Hinge

③ Harness cover

④ Rear view camera

⑤ Hatch

After cord installation (Fig. 19, Fig. 20)

• Open and close the hatch door slowly

to confirm that the cord is not rubbing

against the rim of the door.

① Rear view camera

② Hatch

③ Cord

• When the rear view camera cord cannot

be pulled out from the lower side due to

the type of car.

As shown in the figure 18, bend the cord

into a U shape in front of the waterproof

pad, making sure that rain water cannot

enter the car by running down the cord.

① Plastic clamp

② Waterproof pad

③ Rubber packing

④ Make a U-shaped loop in the lead outside

the rubber packing to prevent rainwater from

flowing along the lead into the interior of the

vehicle.

① Image processing unit power supply

③ RCA power supply

cable connector

② Rear view camera

connector

⑩ Button unit

connector

⑨ Button unit

⑥ Red

⑤ RCA pin

⑧ Black

⑦ Fuse (1A) 3 m (9 ft. 10 in.)

3 m (9 ft. 10 in.)

④ Rear view camera

1.5 m (4 ft. 11 in.)

7 m (23 ft.)

① Plastic clamps

② Rear view

camera

④ Product with a video input

jack (Hideaway unit etc.)

⑦ Made with a rasp etc.

⑧ Scuff plate

⑨ Plastic clamp

⑩ Waterproof plate

③ RCA power

supply cable

⑤ Image processing unit power supply

⑥ Button unit

4 m (13 ft. 2 in.)

⑪ Double-sided

tape (rectangular)

Page is loading ...

Mode ND BC20 PA Installation guide

Brand: Mode

Model: ND BC20 PA

Category: Car video systems

Type: Installation guide

Download PDF

report

in other languages

italiano: Mode ND BC20 PA Guida d'installazione
français: Mode ND BC20 PA Guide d'installation
español: Mode ND BC20 PA Guía de instalación
Deutsch: Mode ND BC20 PA Installationsanleitung

Mode ND BC20 PA Installation guide

Mode ND BC20 PA Installation guide

in other languages

Related papers

Other documents