Rosemount pH Sensor Baseefa Hazardous Area Owner's manual

Rosemount
Brand
Rosemount
Model
pH Sensor Baseefa Hazardous Area
Type
Owner's manual

Rosemount pH Sensor Baseefa Hazardous Area

The Rosemount pH Sensor Baseefa Hazardous Area is a sensor designed for use in hazardous areas. It is approved for use in Zone 1 hazardous areas, and it is certified to ATEX and IECEx standards. The sensor is also approved for use in non-hazardous areas.

The sensor is a simple apparatus, and it does not require a preamplifier. It is compatible with any approved single or multi-channel barrier or apparatus. The sensor can be installed within the hazardous (classified) location for which it is approved.

The sensor has the following features:

  • It is made of durable materials that are resistant to corrosion and wear.

Rosemount pH Sensor Baseefa Hazardous Area

The Rosemount pH Sensor Baseefa Hazardous Area is a sensor designed for use in hazardous areas. It is approved for use in Zone 1 hazardous areas, and it is certified to ATEX and IECEx standards. The sensor is also approved for use in non-hazardous areas.

The sensor is a simple apparatus, and it does not require a preamplifier. It is compatible with any approved single or multi-channel barrier or apparatus. The sensor can be installed within the hazardous (classified) location for which it is approved.

The sensor has the following features:

  • It is made of durable materials that are resistant to corrosion and wear.
Baseefa pH Sensor Hazardous Area Installation
Instruction Sheet
PN 1700737
July 2011/RevA
Any Approved Single
Multi-Channel Barrier or
Apparalus
Non-Hazardous
Hazardous (Classified) Location
SENSOR
ENTITY PARAMETERS (FOR SENSERS WITH PREAMPS)
V
t = 13.1V, It = 500mA
P
max = 700mW
C
i = 0.3 μF, Ii = 0mH
II 1 G Ex ia IIC T4 Ga (-20° < Ta < +60°C)
ATEX & IECEx
NOTES: UNLESS OTHERWISE SPECIFIED
1. NO REVISION TO THIS DRAWING IS PERMITTED WITHOUT AGENCY APPROVAL.
2. V
max > Vt; Imax > It; (Ci OF ALL LOOPS + C CABLE) < Ca;
(L
i OF ALL LOOPS + L CABLE) < La, Pmax OR Pi > P0.
3. SINGLE MULTI-CHANNEL IS BARRIER OR APPARATUS MUST BE APPROVED,
4. SINGLE MULTI-CHANNEL IS BARRIER OR APPARATUS MANUFACTURE'S CONTROL
DRAWINGS MUST BE FOLLOWED WHEN INSTALLING THE SYSTEM. IS BARRIER OR
EQUIPMENT MAY BE INSTALLED WITHIN THE HAZARDOUS (CLASSIFIED) LOCATION
FOR WHICH IT IS APPROVED.
5. INSTALLATION MUST BE IN ACCORDANCE WITH ARTICLE 500 OF THE NEC (ANSI/NFPA 70)
AND ANSI/ISA RP 12.6.
WARNING: SUBSTILUTION OF COMPONENTS MAY INPAIR INTRINSIC SAFETY.
6. pH & AMPERMETRIC SENSORS WITHOUT PREAMPS ARE SIMPLE APPRARATUS.
TITLE
SCALE: NONE
WEIGHT:
SHEET 1 OF 2
SIZE
C
DWG NO
1400334
REV
A
SCHEMATIC, INSTALLATION,
I. S. SENSOR, ATEX
Baseefa Installation Drawing
3900/VP
3500/VP
3300HT/VP
3400HT/VP
396/VP
396R/VP
396P/VP
398R/VP
399/VP
389/VP
385/385+
Basefa Certificate Number: Baseefa10ATEX0156X
The pH sensors listed below can be used with this installation drawing.
Sensors may or may not contain an integral preamplifier.
Emerson Process Management
2400 Barranca Parkway
Irvine, CA 92606 USA
Tel: (949) 757-8500
Fax: (949) 474-7250
http://www.raihome.com
© Rosemount Analytical Inc. 2011
ROSEMOUNT
Analytical
WARNING
EXPLOSION HAZARD
ELECTROSTATIC
Only clean with damp cloth.
Pressurized
spray injury
Assembled in Mexico
Model#3500-PR-02-10-21-30
RTD Pt100 Soft. Ver. ____
SN:B10-1245078-002
A/M 3500P-PR-02-10-21-30-
(BAR CODE)
SQ#10123 SO#81000123
BAS: 9241722-00/A
CSA: 9241723-00/A
FM: 9241724-00/A
Baseefa10ATEX0156X
See manual.
IECEx BAS 10.0083X
Ex ia IIC T4 Ga (-20°C < Ta < 60°C)
II 1 G
1180
Irvine, CA, USA
®
TITLE
SCALE: 1:1
WEIGHT:
SHEET 1 OF 1
SIZE
B
DWG NO
9241728-00
REV
A
LABEL, SENSOR
3800/3800VP, BASEEFA
LABEL, INFORMATION,
SENSOR, BASEEFA
TITLE
S
CALE: NONE
WEIGHT:
SHEET 1 OF 1
SIZE
B
DWG NO
9241722-00
REV
A
extracted from drawing 9241728-00
extracted from drawing 9241722-00
Sample Labels
Information from other agencies may appear on this label.
These are data fields; information may vary from what is shown.
2
1
2
1
See manual.
Baseefa10ATEX0156X IECEx BAS 10.0083X
Ex ia IIC T4 Ga (-20°C < Ta < 60°C)
II 1 G
1180
ROSEMOUNT
A
n
a
l
t
i
c
a
lA
n
a
l
t
i
c
a
lA
n
a
l
t
i
c
a
lA
n
a
l
t
i
c
a
lA
n
a
l
t
i
c
a
lA
n
a
l
t
i
c
a
lA
n
a
l
t
i
c
a
lA
n
y
l
t
i
c
a
l
MODEL
SN
to 105°C
(140°C)
6 barg
(BAR CODE)
®
Made in USA
Information from other agencies may appear on this label.
1
1
  • Page 1 1
  • Page 2 2

Rosemount pH Sensor Baseefa Hazardous Area Owner's manual

Rosemount
Brand
Rosemount
Model
pH Sensor Baseefa Hazardous Area
Type
Owner's manual

Rosemount pH Sensor Baseefa Hazardous Area

The Rosemount pH Sensor Baseefa Hazardous Area is a sensor designed for use in hazardous areas. It is approved for use in Zone 1 hazardous areas, and it is certified to ATEX and IECEx standards. The sensor is also approved for use in non-hazardous areas.

The sensor is a simple apparatus, and it does not require a preamplifier. It is compatible with any approved single or multi-channel barrier or apparatus. The sensor can be installed within the hazardous (classified) location for which it is approved.

The sensor has the following features:

  • It is made of durable materials that are resistant to corrosion and wear.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents