ATEN VP2730 User manual

7 x 3 Seamless Presentation Switch

with Streaming, HDBaseT

VP2730 User Manual

www.aten.com

VP2730 User Manual

ii

EMC Information

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE

STATEMENT: This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user will

be required to correct the interference at his own expense.

FCC Caution: Any changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority to operate this

equipment.

Warning: Operation of this equipment in a residential environment could cause

radio interference.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference

that may cause undesired operation.

Suggestion: Shielded twisted pair (STP) cables must be used with the unit to

ensure compliance with FCC & CE standards.

Achtung: Der Gebrauch dieses Geräts in Wohnumgebung kann

Funkstörungen verursachen.

RoHS

This product is RoHS compliant.

VP2730 User Manual

iii

User Information

Online Registration

Be sure to register your product at our online support center:

Telephone Support

For telephone support, call this number:

User Notice

All information, documentation, and specifications contained in this manual are

subject to change without prior notification by the manufacturer. The

manufacturer makes no representations or warranties, either expressed or

implied, with respect to the contents hereof and specifically disclaims any

warranties as to merchantability or fitness for any particular purpose. Any of the

manufacturer's software described in this manual is sold or licensed as is.

Should the programs prove defective following their purchase, the buyer (and

not the manufacturer, its distributor, or its dealer), assumes the entire cost of all

necessary servicing, repair and any incidental or consequential damages

resulting from any defect in the software.

The manufacturer of this system is not responsible for any radio and/or TV

interference caused by unauthorized modifications to this device. It is the

responsibility of the user to correct such interference.

The manufacturer is not responsible for any damage incurred in the operation

of this system if the correct operational voltage setting was not selected prior to

operation. PLEASE VERIFY THAT THE VOLTAGE SETTING IS CORRECT

BEFORE USE.

International http://eservice.aten.com

International 886-2-8692-6959

China 86-400-810-0-810

Japan 81-3-5615-5811

Korea 82-2-467-6789

North America 1-888-999-ATEN ext 4988

1-949-428-1111

VP2730 User Manual

iv

Package Contents



1 VP2730 7 x 3 Seamless Presentation Matrix Switch



1 IR Receiver



1 IR Remote Control



1 Power Cord



2 Terminal Blocks



4 Foot Pads



1 User Instructions

Note: Make sure that all of the items are present and in good order. If anything

is missing or was damaged in shipping, please contact your dealer for

further assistance.

VP2730 User Manual

v

Contents

EMC Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

RoHS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Online Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

User Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv

About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii

Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii

1. Introduction

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Planning the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Required Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Optional Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2. Hardware Setup

Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

VP2730 Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

VP2730 Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

IR Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

LED Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Rack Mount. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Under Desk Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3. Local Operation

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Operation Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Switching the Display Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Using the IR Remote Control / Front-panel Pushbutton . . . . . . . . . . . 16

Using the OSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

The OSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Launching the OSD to a Specific Display . . . . . . . . . . . . . . . . . . . . . . 19

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Enabling a Multiview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Changing the Display Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Moderator Mode (Remote Display Control) . . . . . . . . . . . . . . . . . . . . . . . 26

Locking the Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

VP2730 User Manual

vi

System Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

4. Remote Operation

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Supported Web Browsers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

The VP2730’s IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

The Participant Account . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Logging in as Participant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

The Participant Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Sharing a Screen or an Application Window . . . . . . . . . . . . . . . . . . . 37

The Administrator Account . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Logging in as Administrator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

The Administrator Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Configuration View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Presentation View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

General Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Audio Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Source Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Display Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

Network Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Upgrading the System Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Backing Up System Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

Restoring System Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

Resetting the VP2730 to Default . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Applying SSL Encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

5. RS-232 Serial Commands

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Command Notations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

RS-232 Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

6. Video Presentation Control App

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Installing and Configuring the App. . . . . . . . . . . . . . . . . . . . . . . . .67

iOS Version. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Main Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Info. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Joining a Meeting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Joining a Meeting Automatically . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Joining a Meeting via Manually Connect . . . . . . . . . . . . . . . . . . .72

Meeting Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Streaming Out Your Content . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75

Chat Room . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

VP2730 User Manual

vii

Video Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Switching a Source for a Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Display Features and Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Multi-view Layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Display Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Source Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Screen Capturing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Moderator Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Audio Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

More VP Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

OSD Notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Android Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Main Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Joining a Meeting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

Joining a Meeting Automatically . . . . . . . . . . . . . . . . . . . . . . . . . . 92

Joining a Meeting via Manually Connect . . . . . . . . . . . . . . . . . . . 94

Meeting Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

Streaming Out Your Content . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

Chat Room . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99

Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

Video Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

Switching a Source for a Display . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

Display Features and Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102

Multi-view Layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103

Display Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

Source Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

Screen Capturing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

Moderator Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

Audio Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

More VP Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109

OSD Notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110

Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113

Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115

Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116

International . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116

North America . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

VP2730 User Manual

viii

About this Manual

This user manual is provided to help you get the most from the VP2730 unit. It

covers all aspects of installation, configuration, and operation. An overview of

the information found in the manual is provided below.

Chapter 1, Introduction introduces you to the 7 x 3 Seamless Presentation

Matrix Switch. Its purpose, features, benefits, and installation considerations

are described.

Chapter 2, Hardware Setup introduces the panel components of the 7 x 3

Seamless Presentation Matrix Switch and the IR Remote Control, and details

the steps to quickly and safely set up the VP2730.

Chapter 3, Local Operation provides information on locally operating and

configuring the VP2730 via the panel pushbuttons and IR remote control.

Chapter 4, Remote Operation provides details on remote tasks such as joining

online meetings and configuring system settings via the VP2730’s web

interface.

Chapter 5, RS-232 Serial Commands provides details on the functions and

RS-232 commands that you can use to control the VP2730 using a serial

controller.

Chapter 6, Video Presentation Control App provides details on remotely

configuring system settings via the ATEN Video Presentation Control App.

An Appendix provides a list of safety instructions and precautions, contact

information for ATEN technical support, product specifications, and other

technical information.

Note:



Read this manual thoroughly and follow the installation and operation

procedures carefully to prevent any damage to the unit or any connected

devices.



ATEN regularly updates its product documentation for new features and

fixes. For an up-to-date VP2730 documentation, visit

http://www.aten.com/global/en/

VP2730 User Manual

ix

Conventions

This manual uses the following conventions:

Product Information

For information about all ATEN products and how they can help you connect

without limits, visit ATEN on the Web or contact an ATEN Authorized Reseller.

Visit ATEN on the Web for a list of locations and telephone numbers:

Monospaced Indicates text that you should key in.

[ ] Indicates keys you should press. For example, [Enter] means to

press the Enter key. If keys need to be chorded, they appear

together in the same bracket with a plus sign between them:

[Ctrl+Alt].

1. Numbered lists represent procedures with sequential steps.

♦ Bullet lists provide information, but do not involve sequential steps.

→ Indicates selecting the option (on a menu or dialog box, for

example), that comes next. For example, Start

→

Run means to

open the Start menu, and then select Run.

Indicates critical information.

International http://www.aten.com

North America http://www.aten-usa.com

VP2730 User Manual

x

This Page Intentionally Left Blank

1

Chapter 1

Introduction

Overview

The VP2730 7 x 3 Seamless Presentation Matrix Switch is a multi-in-one

presentation switch that integrates video matrix switch with scaler, streaming,

audio mixer, HDBaseT extender, and analog-to-digital converter functions into

one compact device. With seven multi-format inputs to two HDMI and one

HDBaseT high-definition outputs, VP2730 empowers larger meetings and

facilitates collaboration between local and remote participants in boardrooms,

video conferencing rooms, lecture halls or distance learning classrooms.

With the user in mind, VP2730 comes with a straightforward and accessible

OSD and web GUI to streamline operation for both local and remote

participants. To facilitate sharing and collaboration with no distance limitations,

VP2730 not only allows the meeting moderator to share video content to up to

five remote sites, but also enables remote sites or local participants to

wirelessly stream in their content for discussion. The moderator can monitor

and switch among sources in any variation of full-screen, dual-view, tri-view,

quad-view or PIP modes, with up to six sources displayed simultaneously on

one screen.

VP2730 also features more advanced meeting management functions:

Moderator Mode enables the meeting moderator to control other displays via

the host display; Chat Room facilitates meeting communications; while Screen

Capture and Freeze record and control the meeting flow. This Collaborative

presentation solution facilitates distance-free content sharing along with

advanced audio, simplifying AV integration via eliminating the need for

numerous individual components and the compatibility challenges that

accompany them.

Chapter 1. Introduction

2

Features

Seamless Multi-format AV Switching



Supports 7 multi-format inputs:



2 combo inputs (HDMI/VGA, HDMI/DisplayPort)



3 HDMI inputs



2 HDMI and 1 HDBaseT outputs



Superior video quality up to 1080p @ 60Hz (HDMI/DisplayPort)



Ultra Seamless Switch

TM

– zero second switching that provides continuous

video streams, real-time video switching, and stable signal transmissions



Scaler – features a scaling function to convert input resolutions to the

optimum display resolutions



Flexible aspect ratio conversion

1080p Streaming for Distance-free Sharing and Collaboration



Go Live – meeting moderator can broadcast HD video streams to up to 5

remote locations

Note: Streaming out requires a bandwidth of 2 MB or more.



Streaming In – remote locations can stream and share video content to the

meeting moderator without distance limitations via intuitive web interface



Streaming queuing – share the streamed-in content approved by the

meeting moderator one at a time to help manage the meeting flow

Audio Mixer Integration for Advanced Audio Support



Audio Mixer – allows mixing of the microphone inputs to any external

analog or digital audio output device



Embed/De-embed Audio – HDMI/DisplayPort audio signals can be

extracted to separate digital/analog audio signals; Mic/Line audio can be

embedded to HDMI audio



Supports multi-format digital/analog audio outputs, including coaxial,

TOSLINK, and RCA up to 2 channels

VP2730 User Manual

3

Advanced Conferencing Management Features for Collaboration



Multi-view – display and switch simultaneously in any variation of full-

screen, dual-view, tri-view, quad-view or PIP modes, with up to six sources

displayed simultaneously on one screen



Moderator Mode – enables the meeting moderator to control other displays

via host display



Chat Room – facilitates real-time and precise communication among

remote participants



Screen Capture – captures anything on your screen with a click



Freeze – freezes the screen for discussion or to control the meeting flow

Streamlined Operation



Multiple Control Options – flexible control via Built-in Web UI, Front Panel,

OSD, IR Remote Control, and RS-232 serial commands



Auto switching – automatically detects and switches to a new source as

soon as it is connected for time-saving and convenience

Chapter 1. Introduction

4

Planning the Installation

Required Equipment

Prepare the following equipment before installing the VP2730 unit.



Source devices



1 to 5 source devices equipped with HDMI, DisplayPort, or VGA ports

(e.g. a laptop, PC, or a Blu-ray disc)

Note: The VP2730 supports Mac or PCs that are Windows, Linux, or Unix-

based.



1 to 5 cables for connecting the source devices to the VP2730



Display devices



1 to 3 display devices equipped with an HDMI connector or an

HDBaseT port (e.g. a monitor or a projector)



1 to 3 cables for connecting the display devices to the VP2730

For information on the number of equipped ports for each connection interface,

see Specifications, page 117.

Optional Equipment

Prepare the following equipment as required.



1 Microphone



1 Speaker



1 RJ-45 cable to connect the VP2730 to a network switch to allow for

streaming over IP and access to the VP2730’s web interface



1 to 3 USB devices to serve as external storage



1 RS-232 controller for serial control

Accessories

Optionally purchase the following for your VP2730:



Rack Mount Kit



Under Desk Mount Kit

For more information about mounting, see Mounting, page 11.

5

Chapter 2

Hardware Setup

Components

VP2730 Front View

No. Component Description

1 Display Selection

Pushbuttons

Press to focus a display. The pushbutton for the

focused display lights amber.

2 Source Selection

Pushbuttons

Press to select a source for the focused display. The

pushbutton for the selected source lights green.

Press

to stream in a video source over the

Internet.

3 Source LEDs Indicate the selected sources for Source (1) and (2).

4 Go Live LEDs Indicate the display that is streamed out.

5Function

Pushbuttons

Press to access multiview, menu, go-live settings,

and mute settings.

6 Navigation

Pushbuttons

Press to navigate and configure settings via the

OSD.

7On/Off

Pushbuttons

Press to turn on/off the unit.

1. Please review the safety information regarding the placement of this

device in Safety Instructions, page 113.

2. Do not power on the VP2730 until all the necessary hardware is

connected.

6

1

2

5

7

4

3

Chapter 2. Hardware Setup

6

VP2730 Rear View

No. Component Description

1 Source (1) Connects up to two source devices, one

equipped with a DisplayPort, another equipped

with an HDMI port. Users can select which

source to display by pressing the Source

Selection pushbutton on the front panel.

2 Source (2) Connects up to two source devices, one

equipped with a VGA port, another equipped with

an HDMI port. Users can select which source to

display by pressing the Source Selection

pushbutton on the front panel.

3 Source (3), (4), and

(5)

Connect to HDMI source devices via HDMI

cables.

4 HDMI Out Connect to display devices equipped with an

HDMI port.

5 HDBaseT Out Connects to a display device equipped with an

HDBaseT port.

6 Phantom Power Enables or disables phantom power supply for a

condenser microphone.

7 Mic In Connects to a microphone.

8 Balanced Audio In Connects to a balanced analog audio source.

9 Digital Audio Out Connects to a speaker via Optical Audio Out or

Coaxial Audio Out port.

10 Stereo Audio Out Connects to a speaker.

11 RS-232 Serial Port Connects to a hardware or software controller to

transmit serial data.

16 17

18

1 2

3

11

15

10

12

13

9

4 5 7 8

14

6

VP2730 User Manual

7

12 Ethernet Port Connects to a network switch via an RJ-45 cable

to allow streaming of audio and video data over

IP.

13 USB Type-A Ports

(2.0)

Receive up to two USB 2.0 devices as external

storages.

14 USB Type-A Port

(3.0)

Receives a USB 3.0 device as an external

storage.

15 IR Receiver Port Connects to an IR receiver to receive IR signals

from the IR remote control.

16 Power Socket Receives a power cord to supply power to the

VP2730.

17 Power Switch Enables (ON) or disables (OFF) the power

supply to the VP2730.

18 Grounding Terminal Grounds the VP2730 to prevent damages from

power surge or static electricity.

No. Component Description

Chapter 2. Hardware Setup

8

IR Remote Control

No. Buttons Description

1 On/Off Turns the VP2730 on or off.

2 Source Selects sources for connected displays.

3 Navigation Navigates in the OSD, selects or unselects options, or

leaves a current screen in the OSD.

4 Notifications Opens the Notifications panel to show logs of system

status, device connection, and user configurations.

Note: When a system setting is configured via the device

panel, OSD, or the web interface, you will be notified via

a text message that pops up at the top-right corner of the

OSD. This message is also logged and saved in the

Notifications panel. To stop receiving the pop-up

notification messages and only keep the messages in the

Notifications panel, go to System Settings >

Notifications in the OSD and configure the Web General

and System General settings.

5 Display Focuses the chosen display.

1

2

3

4

5

6

VP2730 User Manual

9

6Function



: Displays the OSD. Press again to display the

OSD for the next connected display.



: Switches the current display to multiview.



: Streams out the current display out via the

Ethernet.



: Mutes all displays and speakers.

No. Buttons Description

Chapter 2. Hardware Setup

10

LED Display

You can find the unit’s LEDs as illustrated below. See the table below for details

on LED indication.

No. LED Indication Description

1 Display Pushbuttons Light amber The indicated display device (Display A, B,

or C) is focused.

2 Source Pushbuttons Light green The indicated source is selected for display.

3 Source LEDs Light green The indicated source (interface) is selected

for the combo port.

4 Go Live LEDs Light amber The indicated display is streamed out.

5 Power Lights green The unit is powered and turned to ON.

Lights orange The unit is connected to power, but is

currently OFF.

6ACT

(Left LED)

Lights orange Data is being transmitted at 100 Mpbs.

Lights green Data is being transmitted at 1 Gpbs.

Link

(Right LED)

Lights green LAN is connected and no data is being

transmitted.

Blinks green LAN is connected and data is being

transmitted.

VP2730 Front

VP2730 Rear

5

6

1

3

2

4

Page is loading ...

ATEN VP2730 User manual

ATEN VP2730 User manual

Related papers

Other documents