Renkforce Network adapter 1 Gbps LAN (10/100/1000 Mbps), USB 3.0 Owner's manual

Brand: Renkforce

Model: Network adapter 1 Gbps LAN (10/100/1000 Mbps), USB 3.0

Type: Owner's manual

Page is loading ...

• With newer driver versions, this path specication may change. In this case, follow the

manufacturer’s operating instructions supplied with the software.

Depending on the Windows version, administrator rights might be necessary to

install the drivers.

• After completion of the driver installation connect the gigabit network adaptor to a USB3.0

port of the computer. Connect the RJ45 port of the gigabit network adaptor to your switch or

router using a 1:1 connected network cable.

• It might be necessary to restart Windows, before the gigabit network adaptor can work

correctly.

Tips & notes

• The gigabit network adaptor should only be connected to a USB3.0 port of the computer

because a USB1.1-/USB2.0 port is not only too slow but it also does not provide enough

current for the operation of the gigabit network adaptor (USB3.0 provides up to 900 mA,

USB1.1/2.0 only 500 mA).

• If you have a network or system administrator who is responsible for your network (for example

in a larger company), allow him or her carry out the connection and driver installation; do not

install the gigabit network adaptor yourself.

• The stated maximum data transfer rate of 10/100/1000 MBit will not be attained in practice.

This is due to the communication method used, transmission errors, other devices in the

network etc.

• With Windows, it might take some time until the PCs appear on the network.

When you turn on the computer and if Windows is loaded on all computers you will be able

to access the other PC’s immediately.

If, after a few minutes, it is still not possible to access other PCs, check any rewall and/or

virus scanner settings that may be used.

Naturally, the access permissions also have to be set accordingly, if you are using an

operating system that offers such features.

Consult the applicable operating instructions, when using a network printer or other devices

in the network.

There are numerous causes explaining why a network connection is not successful. Please

refer to the appropriate specialist literature or to a specialist technician.

• If you are not using a DHCP Server (e.g. integrated in all DSL-routers), you should assign a

static IP address to each device within the network.

For example, set the router to 192.168.1.1, set the rst computer to 192.168.1.2, the second

computer to 192.168.1.3, and so on. The rst three digits must be the same on all computers;

the last digit can range from 1 to 254.

The “subnet mask” has to be set to 255.255.255.0 for all the computers in the network.

Please keep in mind that an IP address (such as 192.168.1.1) can only be used once in the

network. When you set your router to the IP address 192.168.1.1, no other device in the

network can use this IP address!

• Always ensure sufcient ventilation of the gigabit network adapter. It may heat up considerably

during operation. Do not cover the gigabit network adapter.

• There are two LEDs on the gigabit network adaptor, which indicate the corresponding

function:

Blue LED: Lights up with gigabit connection

Red LED: ashes during data transfer

Care and cleaning

• Disconnect the product from the power supply before cleaning.

• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as

they can cause damage to the housing and malfunctioning.

• Clean the product with a dry, ber-free cloth.

• Do not immerse the product in water.

Disposal

Electronic devices are recyclable waste and must not be disposed of in the

household waste. At the end of its service life, dispose of the product according to

the relevant statutory regulations.

You thus full your statutory obligations and contribute to the protection of the

environment.

Technical data

Connection ................................... USB3.0

Network ........................................ 10/100/1000 MBit

Cable length ................................. approx. 17 cm

Dimensions (W x H x D) ............... 20 x 19 x 60 mm

Weight .......................................... 27 g

Operating instructions

USB3.0 Gigabit Network Adapter

Item no. 1601751

Intended use

The product is designed to be connected to the USB3.0 port on a computer and it is intended

to serve as a network port (10/100/1000 MBit).

It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in

bathrooms, must be avoided under all circumstances.

For safety and approval purposes, you must not rebuild and/or modify this product. If you use

the product for purposes other than those described above, the product may be damaged.

In addition, improper use can cause hazards such as short circuiting, re etc. Read the

instructions carefully and keep them. Make this product available to third parties only together

with its operating instructions.

This product complies with the statutory national and European requirements. All company

Delivery content

• Gigabit network adaptor

• Data carrier with driver

• Operating instructions

Latest operating instructions

Download the latest operating instructions via the link www.conrad.com/downloads or scan the

QR code shown. Follow the instructions on the website.

Explanation of symbols

An exclamation mark in a triangle indicates important instructions in this operating

manual that absolutely have to be observed.

The arrow symbol indicates specic tips and advice on operation.

Safety instructions

Read the operating instructions carefully and especially observe the safety

information. If you do not follow the safety instructions and information

on proper handling in this manual, we assume no liability for any resulting

personal injury or damage to property. Such cases will invalidate the warranty/

guarantee.

• The device is not a toy. Keep it out of the reach of children and pets.

• Do not leave packaging material lying around carelessly. This may become

dangerous playing material for children.

• Protect the product from extreme temperatures, direct sunlight, strong jolts, high

humidity, moisture, ammable gases, vapours and solvents.

• Do not place the product under any mechanical stress.

• If it is no longer possible to operate the product safely, take it out of operation and

protect it from any accidental use. Safe operation can no longer be guaranteed

if the product:

- is visibly damaged,

- is no longer working properly,

- has been stored for extended periods in poor ambient conditions or

- has been subjected to any serious transport-related stresses.

• Please handle the product carefully. Jolts, impacts or a fall even from a low height

can damage the product.

• Also observe the safety and operating instructions of any other devices which are

connected to the product.

• Consult an expert when in doubt about operation, safety or connection of the

device.

• Maintenance, modications and repairs are to be performed exclusively by an

expert or at a qualied shop.

• If you have questions which remain unanswered by these operating instructions,

contact our technical support service or other technical personnel.

Driver installation, connection

Do not connect the USB gigabit network adaptor to the computer yet. First install the

required driver.

• Insert the supplied data carrier into the respective drive of your computer.

• If the installation program does not start automatically, you can nd the suitable driver in the

directory “ASIX \ AX88179 \ Windows”, and there in the sub-folder of the respective Windows

version used.

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).

All rights including translation reserved. Reproduction by any method, e.g. photocopy, microlming, or the

capture in electronic data processing systems require the prior written approval by the editor. Reprinting, also in

part, is prohibited. This publication represent the technical status at the time of printing.

Page is loading ...

Renkforce Network adapter 1 Gbps LAN (10/100/1000 Mbps), USB 3.0 Owner's manual

Brand: Renkforce

Model: Network adapter 1 Gbps LAN (10/100/1000 Mbps), USB 3.0

Type: Owner's manual

Download PDF

report

Renkforce Network adapter 1 Gbps LAN (10/100/1000 Mbps), USB 3.0 Owner's manual

Renkforce Network adapter 1 Gbps LAN (10/100/1000 Mbps), USB 3.0 Owner's manual

in other languages

Related papers

Other documents