Page 2

Trademarks

Trademarks Used In This Manual

Black Box and the Double Diamond logo are registered trademarks of

BB Technologies, Inc.

The Laptop Depot design is patent pending.

Any other trademarks mentioned in this manual are acknowledged to be

the property of the trademark owners.

Table of Contents

1.0 Specifications ..................................................................................................... 4

1.1 Overview ............................................................................................. 4

2.0 What’s Included ................................................................................................. 5

3.0 Precautions ........................................................................................................ 7

Page 4

1.0 Specifications

Capacity — Holds five or eight laptop computers

Standards — UL

Power Strip — LTD5: (1) 5-outlet power strip, 0.75 amps per outlet max.;

LTD8: (1) 8-outlet power strip, 0.75 amps per outlet max.

Size — LTD5

Body: 17

Casters: 3.9"H

Drawer: 5.4"H x 9.2"W x 16"D

Door opening: 14"H x 11"W

Both: Netbook Slot: 12.5"H x 2"W x 17"D ( 31.8 x 5 x

1.1 Overview

The Laptop Depot (LTD) and Laptop Depot with Pedestal (LTDB) are designed to store,

transport, and charge laptop computers and other similar devices. Units are available

with capacities for five or eight separate storage bays. Each unit plugs into a typical

2.0 What‘s Included

Laptop Depot (LTD5 and LTD8)

Laptop Depot Base (LTD5B and LTD8B)

• Caster base with locking drawer

• Laminate top

• (6) 10 x 3/4" black particle board screws

• (4) 10-24 x 1.5" steel screws

• (4) 10-24 flange nuts

• User’s manual

• Pair of keys

Page 6

2.1 Front and Rear Views of the Laptop Depot

3.0 Precautions

• The LTD and LTDB must ONLY be connected to a 120 volt AC 15- or-20 amp power

• Do not use an extension cord in conjunction with the LTD.

• NO LIQUIDS in or around the LTD and LTDB environment.

• Inadequate repair can create significant hazards to users and is not covered by the

• For your safety, it is recommended that a qualified electrician test the circuit you

• The LTD ground prong must be present for safe operation. If the plug is damaged

• The use of the LTD including: plugging in or unplugging laptop computers,

• Misuse, incorrect operation, or inadequate repair of the LTD will void the warranty.

Page 8

4.0 Configuration and Setup

Remove and discard all packaging materials. Open and inspect the LTD or LTDB to

verify all doors, drawers, and locks are working properly.

computers to prevent the LTDB from moving.

Feed the power strip cord through the grommet hole located on the side of the LTD.

Do not plug the LTD into the wall outlet until all configurations and setup are

complete.

Attach power bricks to the dividers to create separate slots for the laptop computers.

4.1 Installing Power Bricks on the Dividers

Remove a divider to install a power brick on it. Follow these steps to install the power

bricks on each divider:

Step 1. Lay the divider flat on the work surface. Lay a laptop computer and a power

brick on top of the divider, with the computer end of the power wire toward the top

of the divider. Plug the power brick into the laptop computer. Lay the wire across the

Step 2. Note the point where the power wire meets the rear hole in the divider.

Measure back 6" toward the power brick and fold the wire in half to create a loop in

the center of the wire. This loop will be used in Step 3, below. Unplug the power

wire from the netbook and remove the netbook from the divider.

Step 4. Run the wire along the top of the divider and repeat the process of creating

a loop in the power cord. Place this loop through the small hole at the front of the

divider (Figure 4-5). Now place the plug end of the wire through the loop (Figure

4-6). Pull the end of the cable, tightening the loop (Figure 4-7).