Saeco HD8760/09 User manual

Category
Coffee makers
Type
User manual

This manual is also suitable for

INSTRUCTIONS FOR USE
Read carefully before using the machine.
Register your product and get support at
www.philips.com/welcome
English
Type HD8760
EN
02
02
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be
followed, including the following:
1. Read all instructions.
2. Do not touch hot surfaces. Use handles or knobs.
3. To protect against fire, electric shock and injury to persons do not immerse
cord, plugs, or appliance in water or other liquid.
4. Close supervision is necessary when the appliance is used by or near
children.
5. Unplug from outlet when not in use and before cleaning. Allow to cool
before putting on or taking off parts, and before cleaning the appliance.
6. Do not operate any appliance with a damaged cord or plug or after the
appliance malfunctions, or has been damaged in any manner. Return
appliance to the nearest authorized service facility for examination, repair
or adjustment.
7. The use of accessory attachments not recommended by the appliance
manufacturer may result in fire, electric shock or injury to persons.
8. Do not use outdoors.
9. Do not let cord hang over edge of table or counter, or touch hot surfaces.
10. Do not place on or near a hot gas or electric burner, or in a heated oven.
11. Always attach plug to appliance first, then plug cord into wall outlet. To
disconnect, turn any control to “off”, then remove plug from wall outlet.
12. Do not use appliance for other than intended use.
13. Save these instructions.
SAVE THESE INSTRUCTIONS
CAUTION
This appliance is for household use only. Any servicing, other than cleaning
and user maintenance, should be performed by an authorized service center.
Do not immerse machine in water. To reduce the risk of fire or electric shock,
do not disassemble the machine. There are no parts inside the machine
serviceable by the user. Repair should be done by authorized service personnel
only.
1. Check voltage to be sure that the voltage indicated on the nameplate
corresponds with your voltage.
2. Never use warm or hot water to fill the water tank. Use cold water only.
3. Keep your hands and the cord away from hot parts of the appliance during
operation.
4. Never clean with scrubbing powders or harsh cleaners. Simply use a soft
cloth dampened with water.
5. For optimal taste of your coffee, use purified or bottled water. Periodic
descaling is still recommended every 2-3 months.
6. Do not use caramelized or flavored coffee beans.
INSTRUCTIONS FOR THE POWER
SUPPLY CORD
A. A short power-supply cord (or detachable power-supply cord) is to be
provided to reduce risks resulting from becoming entangled in or tripping
over a longer cord.
B. Longer detachable power-supply cords or extension cords are available
and may used if care is exercised in their use.
C. If a long detachable power-supply cord or extension cord is used,
1. The marked electrical rating of the detachable power-supply cord or
extension cord should be at least as great as the electrical rating of the
appliance
2. If the appliance is of the grounded type, the extension cord should be a
grounding-type 3-wire cord, and
3. The longer cord should be arranged so that it will not drape over the
counter top or table top where it can be pulled on by children or tripped
over.
2
ENGLISH
Congratulations on your purchase of a Saeco Minuto Pure
full automatic espresso machine!
To fully bene t from the support that Saeco o ers, please
register your product at www.philips.com/welcome.
This user manual applies to HD8760.
The machine is suitable for preparing espresso co ees using
whole co ee beans.
In this user manual you will  nd all the information you need
to install, use, clean and descale your machine.
3
ENGLISH
CONTENTS
IMPORTANT..................................................................................................... 4
Safety Instructions .......................................................................................................................... 4
Warning .......................................................................................................................................... 4
Caution ........................................................................................................................................... 6
Compliance with Standards ............................................................................................................ 7
INSTALLATION ................................................................................................. 8
Product overview ............................................................................................................................ 8
General description ......................................................................................................................... 9
PREPARING FOR USE .......................................................................................10
Machine Packaging ....................................................................................................................... 10
Machine Installation ..................................................................................................................... 10
USING THE MACHINE FOR THE FIRST TIME ........................................................12
Circuit priming .............................................................................................................................. 12
Automatic rinse/self-cleaning cycle .............................................................................................. 13
“INTENZA+” water  lter installation ............................................................................................. 14
ADJUSTMENTS ................................................................................................15
Saeco Adapting System ................................................................................................................. 15
Adjusting the Co ee Grinder. ........................................................................................................ 16
Adjusting the Dispensing Spout .................................................................................................... 17
Adjusting the co ee length .......................................................................................................... 18
ESPRESSO AND COFFEE BREWING ....................................................................19
CLEANING AND MAINTENANCE ........................................................................20
Daily cleaning of the machine ....................................................................................................... 20
Daily cleaning of the water tank.................................................................................................... 21
Weekly cleaning of the machine ................................................................................................... 22
Weekly cleaning of the brew group ............................................................................................... 22
Monthly lubrication of the brew group ......................................................................................... 25
Monthly cleaning of the co ee bean hopper ................................................................................. 26
DESCALING .....................................................................................................27
WARNING SIGNALS .........................................................................................32
TROUBLESHOOTING ........................................................................................35
ENERGY SAVING ..............................................................................................37
Stand-by ....................................................................................................................................... 37
Disposal ........................................................................................................................................ 37
TECHNICAL SPECIFICATIONS ............................................................................38
WARRANTY AND SERVICE ................................................................................38
Warranty ....................................................................................................................................... 38
Service .......................................................................................................................................... 38
ORDERING MAINTENANCE PRODUCTS ..............................................................39
4
ENGLISH
IMPORTANT
Safety Instructions
This machine is equipped with safety features. Nevertheless
read the safety instructions carefully and only use the
machine as described in these instructions to avoid accidental
injury or damage.
Keep this user manual for future reference.
The term WARNING and this icon warn against possible
severe injuries, danger to life and/or damage to the machine.
The term CAUTION and this icon warn against slight
injuries and/or damage to the machine.
This icon requests to read carefully this instruction manual,
before performing any use or maintenance operation.
Warning
Connect the machine to a wall socket with a voltage
matching the technical speci cations of the machine.
Do not let the power cord hang over the edge of a table or
counter, or touch hot surfaces.
Never immerse the machine, mains plug or power cord in
water (danger of electrical shock).
Never direct the hot water jet towards body parts: danger
of burns!
Do not touch hot surfaces. Use handles and knobs.
5
ENGLISH
5
Remove the mains plug from the wall socket:
- If a malfunction occurs.
- If the machine will not be used for a long time.
- Before cleaning the machine.
Pull on the plug, not on the power cord. Do not touch
the mains plug with wet hands.
Do not use the machine if the mains plug, the power cord
or the machine itself is damaged.
Do not make any modi cations to the machine or its
power cord. Only have repairs carried out by a service
centre authorised by Philips to avoid a hazard.
The machine should not be used by children younger than
8 years old.
The machine can be used by children of 8 years and
upwards if they have previously been instructed on
the correct use of the machine and made aware of the
associated dangers or if they are supervised by an adult.
Cleaning and maintenance should not be carried out
by children unless they are more than 8 years old and
supervised by an adult.
Keep the machine and its power cord out of reach of
children under 8 years old.
The machine may be used by persons with reduced
physical, sensory or mental capabilities or lacking
su cient experience and/or skills if they have previously
been instructed on the correct use of the machine and
made aware of the associated dangers or if they are
supervised by an adult.
6
ENGLISH
Children should be supervised to ensure that they do not
play with the machine.
Never insert  ngers or other objects into the co ee
grinder.
Caution
The machine is for household use only and is not intended
for use in environments such as canteens, sta kitchens of
shops, o ces, farms or other work environments.
Always put the machine on a  at and stable surface.
Do not place the machine on hot surfaces, directly next to
a hot oven, heater or similar source of heat.
Only put co ee beans into the co ee bean hopper. If
ground co ee, instant co ee or any other substance is put
in the co ee bean hopper, it may damage the machine.
Let the machine cool down before inserting or removing
any parts.
Never use warm or hot water to  ll the water tank. Use
only cold non sparkling drinking water.
Never clean with scrubbing powders or harsh cleaners.
Simply use a soft cloth dampened with water.
Descale your machine regularly. The machine indicates
when descaling is needed. Not doing this will make your
appliance stop working properly. In this case repair is not
covered under your warranty!
Do not keep the machine at temperature below 0 °C.
Residue water in the heating system may freeze and cause
damage.
7
ENGLISH
7
Do not leave water in the water tank when the machine
is not used over a long period of time. The water can be
contaminated. Use fresh water every time you use the
machine.
Compliance with Standards
The machine complies with art.13 of the Italian Legislative
Decree dated 25 July 2005, no. 151 “Implementation of the
Directives 2005/95/EC, 2002/96/EC and 2003/108/EC on
the restriction of the use of certain hazardous substances in
electrical and electronic equipment, as well as waste disposal”.
This machine complies with EU Directive 2002/96/EC.
This Philips appliance complies with all the applicable
standards and regulations relating to the exposure to
electromagnetic  elds.
8
INSTALLATION
Product overview
30
18
14
15
17
19
12
3
10 11 12 13
4
5
6
7
8
9
20 21 22
24 26
25 27
16
2328 29
9
ENGLISH
9
General description
1. Grinder adjustment knob
2. Co ee bean hopper
3. Water tank + Lid
4. Co ee bean hopper lid
5. Control panel
6. Dispensing spout
7. Full drip tray indicator
8. Cup holder grill
9. Drip tray
10. Co ee grounds drawer
11. Brew group
12. Co ee residues drawer
13. Service door
14. Grease for the brew group
15. Power cord
16. Cleaning brush
17. Co ee grinder adjustment key
18. Power cord socket
19. Power button
20. Espresso brew button
21. ON/OFF button
22. Co ee brew button
23. Descaling button
24. No water light
25. General warning light
26. Empty co ee grounds drawer light
27. No co ee light
28. Descaling cycle light
29. Rinse cycle light
30. Descaling solution- to be purchased separately
10
ENGLISH
PREPARING FOR USE
Machine Packaging
The original packaging has been designed and constructed to protect the
machine during transport. We recommend keeping the packaging material
for possible future transport.
Machine Installation
1
Remove the machine from the packaging.
2
For best use, it is recommended to:
Choose a safe, level surface, where there will be no danger of over-
turning the machine or being injured.
Choose a location that is su ciently well-lit, clean and near an eas-
ily reachable socket.
Allow for a minimum distance from the sides of the machine as
shown in the illustration.
3
Remove the water tank lid.
4
Lift the water tank using the handle.
11
ENGLISH
11
8
Slowly pour the co ee beans into the co ee bean hopper.
Note:
Do not pour too many co ee beans into the co ee bean hopper as this will
reduce the grinding performance of the machine.
Caution:
Only co ee beans must be put into the co ee bean hopper. Ground
co ee, instant co ee, caramelized co ee or any other object may
damage the machine.
9
Put back the co ee bean hopper lid on the co ee bean hopper.
10
Insert the plug into the socket located on the back of the machine.
11
Insert the plug at the other end of the power cord into a wall socket
with suitable power voltage.
1
2
5
Rinse the water tank with fresh water.
6
Fill the water tank with fresh water up to the MAX level and reinsert it
into the machine. Make sure it is fully inserted.
Caution:
Never  ll the water tank with warm, hot, sparkling water or any other
liquid, as this may cause damage to the water tank and the machine.
7
Remove the co ee bean hopper lid.
12
ENGLISH
12
Switch the power button to “I” to turn on the machine. The button
ashes.
13
To turn on the machine simply press the button.
USING THE MACHINE FOR THE FIRST TIME
When using the machine for the  rst time, the following activities need to
happen:
1) You need to prime the circuit.
2) The machine will perform an automatic rinse/self-cleaning cycle.
Circuit priming
During this process fresh water  ows through the internal circuit of the
machine and the machine warms up. This takes a few minutes.
1
Place a container under the co ee dispensing spout.
2
The machine starts the automatic priming of the circuit by dispensing
some water through the dispensing spout. The
and lights
ash simultaneously.
13
ENGLISH
13
3
The machine warms up and the and buttons  ash simultane-
ously.
Automatic rinse/self-cleaning cycle
When warm-up is complete, the machine automatically performs a rinse/
self-cleaning cycle of the internal circuit with fresh water. This takes less
than a minute.
1
Place a container under the co ee dispensing spout to catch the water
which will be dispensed.
2
The and lights  ash simultaneously. Wait for the cycle to  n-
ish automatically.
3
When the operations described above are complete, the and
buttons are steady on.
Now the machine is ready for use.
Note:
When you haven’t used the machine for 2 or more weeks, the machine
will automatically perform an automatic rinse/self-cleaning cycle after you
switch it on.
The automatic rinse/self-cleaning cycle is also initiated when the machine
has been in stand-by mode, or switched o , for more than 15 minutes.
After this cycle has been completed, you can brew a co ee.
14
ENGLISH
“INTENZA+” water  lter installation
We recommend you to install the “INTENZA+” water  lter as this prevents
limescale build-up in your machine and preserves a more intense aroma of
your co ee.
The “INTENZA+” water  lter can be purchased separately. For further de-
tails, please refer to the maintenance products page in this manual.
Water is a crucial part of every co ee, so it is very important to always have
it professionally  ltered. Using the “INTENZA+” water  lter will prevent
mineral deposits from building up and improve your water quality.
1
Remove the small white  lter from the water tank and store it in a dry
place.
2
Remove the “INTENZA+” water  lter from its packaging, immerse it ver-
tically (with the opening positioned upwards) in cold water and gently
press the sides so as to let the air bubbles out.
3
Set the “INTENZA+” water  lter according to the hardness of the water
used:
A = Soft water
B = Hard water (standard)
C = Very hard water
15
ENGLISH
15
4
Put the “INTENZA+” water  lter into the empty water tank. Press it
down until it cannot move any further.
5
Fill the water tank with fresh water and reinsert it into the machine.
6
Brew 2 co ees to properly prime the circuit.
7
‘When the above steps have been completed’, the and but-
tons light steadily.
Note:
We recommend you to replace the Intenza +  lter every 2 months.
ADJUSTMENTS
The machine allows for certain adjustments so that you can brew the best
tasting co ee possible.
Saeco Adapting System
Co ee is a natural product and its characteristics may change according to
its origin, blend and roast. The machine is equipped with a self-adjusting
system that allows the use of all types of co ee beans available on the
market except for caramelized and  avoured co ee beans.
The machine automatically adjusts itself after brewing several cups of cof-
fee to optimize the extraction.
16
ENGLISH
Adjusting the Co ee Grinder.
‘You can adjust the grinder to set the co ee grinding to your personal
taste.
Warning:
The co ee grinder contains moving parts that may be dangerous. Do
not insert  ngers or other objects. Only adjust the co ee grinder us-
ing the grinder adjustment key.
Warning:
The grinder adjustment knob, inside the co ee bean hopper, must be
turned only when the co ee grinder is running.
1
‘Press and turn the grinder adjustment knob below the co ee bean
hopper one notch at a time. Use the co ee grinder adjustment key
provided with the machine. You will taste the di erence after brewing
2-3 cups of co ee.
1
2
2
The reference marks inside the co ee bean hopper indicate the grind
setting. There are 5 di erent grind settings to choose from position
1 for coarse grind - milder taste to position 2 for  ne grind - stronger
taste.
17
ENGLISH
17
Adjusting the Dispensing Spout
The height of the dispensing spout can be adjusted to better  t the
dimensions of the cups that you wish to use.
Move the dispensing spout up or down with your  ngers to adjust its
height as shown in the image.
The recommended positions are:
For the use of small cups;
For the use of large cups.
Two cups can also be placed under the dispensing spout to brew two cups
of espresso or co ee at the same time.
18
ENGLISH
Adjusting the co ee length
The machine allows you to adjust the amount of brewed co ee according
to your taste and the size of your cups.
Each time the
or button is pressed, the machine brews a pre-set
amount of co ee. Each button may be individually programmed for a
speci c brew setting.
The following procedure describes how to programme the
button.
1
Place a cup under the dispensing spout.
2
Press and hold the button until it starts to  ash quickly. Then
release the button. The machine is now programming. The
button
ashes during the programming cycle.
The machine starts brewing co ee.
3
Press the button as soon as the desired amount of co ee is
reached.
Now the button
is programmed; each time it is pressed, the machine
will brew the same amount of espresso that was just programmed.
Note:
To program the
button, the same steps should be followed.
Press the
button to stop brewing when the desired amount of co ee
is reached.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

Saeco HD8760/09 User manual

Category
Coffee makers
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI