Keys Fitness 2250 Owner's manual

Owner’s Manual

Read all precautions and instruc-

tions in this manual before using

this equipment.

215-00013

10/04

Table of Contents

2

Important Safety Information 3

Before You Start 4

Assembly 5-34

Weight Ratios 35

Weight Stack Sticker Placement 36

Cable View 37-38

Top View 39

Exploded View 40-41

Parts List 42-43

Warranty Information 44

Important Safety Information

3

THANK YOU for making this Power System unit a part of your exercise pro-

gram. Keys Fitness and our Power System Series assures the very best in value,

appearance, durability and biomechanics.

This manual will guide you through the assembly process. If at any time you are

having trouble with the assembly or use of this product, then please contact us at

our Keys Fitness Help-line. We have trained service technicians on site to take

care of you, our valued customer.

REGISTRATION CARD

To avoid unnecessary delays in warranty parts and to insure that a permanent

record of your purchase is on file with our company, be sure to send in the war-

ranty registration card or register on-line at www.keysfitness.com within 10 days

of purchase.

POWER SYSTEM SERIES

QUESTIONS?

CALL

1-888-340-0482

Monday-Friday

8:30-5:30 Central Time

When calling please have the following product information available:

• Product Series

• Model #

• PO # (located on the front of the manual)

• Part Number

• Part Description

Before You Start

4

Prior to assembly, remove components from the box and verify that all the listed parts were supplied.

NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled.

SAFETY INFORMATION WARNING!

Before using this unit or starting any exercise program, consult your physician.

This is especially important for persons over the age of 35 and/or persons with

pre-existing health problems. Keys Fitness Products LP assumes no responsibili-

ty for personal injury or property damage sustained by or through the use of this

product.

It is the owner’s responsibility to ensure that all users of this unit have read the

Owner’s Manual and are familiar with safety information and precautions.

SAFETY PRECAUTIONS

• This Power System unit should only be used on a level surface and is intended

for indoor use only. Keys Fitness recommends an equipment mat be placed

under the unit to protect the floor or carpet and for easier cleaning.

• Wear comfortable, good-quality walking or running shoes and appropriate

clothing. Do not use this unit with bare feet, sandals, socks or stockings!

• Always examine your unit before using to ensure all parts are in working order.

• Do not leave children unsupervised near or on the unit.

• Service to your Power System unit should only be performed by an authorized

service representative, unless authorized and/or instructed by a Keys Fitness

technician. Failure to follow these instructions will void the warranty.

Assembly

5

Box 1

Assembly

6

Box 2

Assembly

7

Box 3

Assembly

8

Box 4

Assembly

9

Box 5

Assembly

10

Box 6

Box 7

Box 9

Box 11

Box 8

Box 10

Assembly

11

Assembly

12

Assembly

13

Step 1

Slide two Guide Rods (24) into Rear Frame A (1) and secure using two Washers (102), two

Spring Washers (103), and two Allen Bolts (97).

Repeat to complete Rear Frame B (128) assembly.

Assembly

14

Figure 1

A

B

Assembly

15

Step 2

Attach Front Upright (86) to Seat Pad Support Receptacle (2) using two Nylon Lock Nuts (104), two

Washers (102), and two Bolts (95).

Slide Seat Pad Support Receptacle (2) onto Rear Frame A (1). Next, attach Main Rear Frame (121) to the

side of Seat Pad Support Receptacle (2). Secure the assembly in place using two Nylon Lock Nuts (104),

four Washers (102), and two Bolt (153).

Connect Pec Dec Mount (7) to Seat Pad Support Receptacle (2) using two Nylon Lock Nuts (104), two

Washers (102), and two Bolts (94). Use one Washer (107), one Spring Washer (103), and one Bolt (93) to

secure it at the top.

Attach Rear Frame B (128) to Rear Main Frame (121) using two Nylon Lock Nuts (104), two Washers

(102), and two Bolts (95).

Figure 2

A

B

Assembly

16

Step 3

Connect Main Upright A (3) to the top of Seat Pad Support Receptacle (2). Use three Washers (101), one

Spring Washers (117), one Nylon Lock Nut (105), and two Bolts (98) to secure them on the bottom. Next, use

three Nylon Lock Nuts (104), six Washers (101), and three Bolts (94) to secure the sides.

Figure 3

A

Step 4

First, slide a Weight Stack Bumper (30) down each Guide Rod (24). Next, slide weight plates down the

Guide Rods (24) in this order: five 15lb Plates (36), nine 10lb Plates (37), five 5lb Plates (38), and the Top

Plate (27). Note: Number of weight plates may vary depending on your specific configuration.

Slide Main Top Beam (4) onto Main Upright A (3) and two Guide Rods (24). Secure to Main Upright A

using two Nylon Lock Nuts (104), four Washers (101), and two Bolts (98). Next, use two Washers (102), two

Spring Washers (103), and two Bolts (97).

Assembly

17

Figure 4

Step 5

Connect Press Arm Support (5) to Main Upright A (3) by sliding Shaft (74) into the assembly. Secure the

assembly using two Screws (84).

Attach Press Arm (6) to Press Arm Support (5) by sliding Shaft (73) into the assembly. Use two Screws (84)

to secure Shaft (73) in place.

Assembly

18

Figure 5

Assembly

19

Step 6

Slide Right Pec Dec Arm (8) on to the shaft of the Pec Dec Mount (7). Secure the arm in place using

one Big Washer (76), one Washer (102), one Spring Washer (103), and one Allen Bolt (97).

Slide Pec Dec Handlebar (19) onto the top of the Right Pec Dec Arm (8) and secure using one Chrome

Washer (106), one Washer (102), one Spring Washer (103), and one Allen Bolt (97).

Repeat this step to complete the Left Pec Dec assembly.

Figure 6

Assembly

20

Step 7

Attach Main Upright B (123) onto Main Rear Frame (121). Secure using two Nylon Lock Nuts (104), four

Washers (102), and two Bolts (95).

Slide Side Top Beam A (122) onto Main Upright B (123) and secure using two Nylon Lock Nuts (105), four

Washers (101), and two Bolts (98).

Secure the Side Top Beam A (122) to the side of Main Top Beam (4) using two Nylon Lock Nuts (104), four

Washer (102), and two Bolts (153).

Figure 7

Page is loading ...

Keys Fitness 2250 Owner's manual

Keys Fitness 2250 Owner's manual

Related papers

Other documents