Dodge 2008 User manual

Caravan

OWNER’S MANUAL

2008

2008 Caravan

81-226-0819 First Edition Printed in U.S.A.

VEHICLES SOLD IN CANADA

With respect to any Vehicles Sold in Canada, the name

Chrysler LLC shall be deemed to be deleted and the

name Chrysler Canada Inc. used in substitution therefor.

DRIVING AND ALCOHOL

Drunken driving is one of the most frequent causes of

accidents.

Your driving ability can be seriously impaired with blood

alcohol levels far below the legal minimum. If you are

drinking, don’t drive. Ride with a designated non-drinking

driver, call a cab, a friend, or use public transportation.

WARNING!

Driving after drinking can lead to an accident. Your

perceptions are less sharp, your reflexes are slower,

and your judgment is impaired when you have been

drinking. Never drink and then drive.

This manual illustrates and describes the operation of

features and equipment that are either standard or op-

tional on this vehicle. This manual may also include a

description of features and equipment that are no longer

available or were not ordered on this vehicle. Please

disregard any features and equipment described in this

manual that are not on this vehicle.

Chrysler LLC reserves the right to make changes in

design and specifications, and/or make additions to or

improvements to its products without imposing any

obligation upon itself to install them on products previ-

ously manufactured.

TABLE OF CONTENTS

SECTION PAGE

1

INTRODUCTION

.............................................................3

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

...............................9

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

...............................97

4

UNDERSTANDING YOUR INSTRUMENT PANEL

................................... 219

5

STARTING AND OPERATING

.................................................321

6

WHAT TO DO IN EMERGENCIES

...............................................409

7

MAINTAINING YOUR VEHICLE

...............................................431

8

MAINTENANCE SCHEDULES

..................................................489

9

IF YOU NEED CONSUMER ASSISTANCE

..........................................497

10

INDEX

....................................................................507

1

2

3

4

5

6

7

8

9

10

INTRODUCTION

CONTENTS

m Introduction ...........................4

m How To Use This Manual ..................4

m Warnings And Cautions ...................6

m Vehicle Identification Number ...............6

m Vehicle Modifications/Alterations ............7

1

INTRODUCTION

This Owner’s Manual has been prepared with the assis-

tance of service and engineering specialists to acquaint

you with the operation and maintenance of your vehicle.

It is supplemented by a Warranty Information Booklet

and various customer-oriented documents. You are

urged to read these publications carefully. Following the

instructions and recommendations in this manual will

help assure safe and enjoyable operation of your vehicle.

NOTE: After you read the manual, it should be stored

in the vehicle for convenient reference and remain with

the vehicle when sold, so that the new owner will be

aware of all safety warnings.

When it comes to service, remember that your authorized

dealer knows your vehicle best, has the factory-trained

technicians and genuine Mopart parts, and is interested

in your satisfaction.

HOW TO USE THIS MANUAL

Consult the Table of Contents to determine which section

contains the information you desire.

The detailed Index at the back of this manual contains a

complete listing of all subjects.

Consult the following table for a description of the

symbols that may be used on your vehicle or throughout

this Owner’s Manual.

4 INTRODUCTION

INTRODUCTION 5

1

WARNINGS AND CAUTIONS

This manual contains WARNINGS against operating

procedures that could result in an accident or bodily

injury. It also contains CAUTIONS against procedures

that could result in damage to your vehicle. If you do not

read this entire manual you may miss important infor-

mation. Observe all Warnings and Cautions.

VEHICLE IDENTIFICATION NUMBER

The Vehicle Identification Number (VIN) is found on the

left front corner of the instrument panel, visible through

the windshield. This number also appears on the Auto-

mobile Information Disclosure Label affixed to a window

on your vehicle, the vehicle registration and title.

NOTE: It is illegal to remove the VIN.

Vehicle Identification Number

6 INTRODUCTION

VEHICLE MODIFICATIONS/ALTERATIONS

WARNING!

Any modifications or alterations to this vehicle could

seriously affect its roadworthiness and safety and

may lead to an accident resulting in serious injury or

death.

INTRODUCTION 7

1

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

CONTENTS

m A Word About Your Keys ..................12

▫ Wireless Ignition Node (WIN) .............12

m Sentry Keyt Immobilizer System .............15

▫ Replacement Keys ......................16

m Security Alarm System — If Equipped .........18

▫ Rearming Of The System .................18

m Illuminated Entry System — If Equipped .......20

m Remote Keyless Entry (RKE) — If Equipped .....21

▫ Using The RKE Transmitter ...............21

m Remote Starting System — If Equipped ........28

▫ How To Use Remote Start ................28

m Door Locks ............................31

▫ Manual Door Locks .....................31

▫ Power Door Locks — If Equipped ..........32

m Windows .............................36

▫ Power Vent Windows — If Equipped ........36

▫ Power Windows .......................37

m Sliding Side Door ........................41

2

▫ Power Sliding Side Door — If Equipped ......42

▫ Sliding Side Door Child Protection Lock ......46

m Liftgate ...............................48

▫ Power Liftgate — If Equipped .............49

m Storage Bin Safety Warning .................52

▫ Safety Warnings .......................52

▫ Storage Bin Cover Emergency Release Strap —

If Equipped ..........................54

▫ Reinstalling Storage Bin Cover Emergency

Release Strap .........................54

m Occupant Restraints ......................55

▫ Lap/Shoulder Belts .....................57

▫ Automatic Locking Retractors (ALR) Mode –

If Equipped ..........................63

▫ Seat Belt Pretensioners ...................64

▫ Enhanced Seat Belt Use Reminder System

(BeltAlertt) ..........................64

▫ Seat Belts And Pregnant Women ............65

▫ Seat Belt Extender ......................66

▫ Supplemental Restraint System (SRS) - Airbag . .66

▫ Airbag System Components ...............67

▫ Front Seat Airbag Features ................67

▫ Airbag Deployment Sensors And Controls .....72

▫ Event Data Recorder (EDR) ...............78

▫ Integrated Child Seat — If Equipped ........80

▫ Child Restraints .......................81

m Rear Seat Delete Feature (Commercial Vehicles Only)

— If Equipped ..........................89

10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

▫ Restraining Infants And Small Children With Seat

Delete Feature (Commercial Vehicles Only) ....90

m Engine Break-In Recommendations ...........93

m Safety Tips ............................93

▫ Safety Checks You Should Make Inside The

Vehicle ..............................93

▫ Periodic Safety Checks You Should Make

Outside The Vehicle ....................94

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11

2

A WORD ABOUT YOUR KEYS

Your vehicle uses a keyless ignition system. This system

consists of a Remote Keyless Entry (RKE) transmitter

with integrated ignition Key and a Wireless Ignition

Node (WIN) with integral ignition switch. You can insert

the double-sided key into the ignition switch with either

side up.

Wireless Ignition Node (WIN)

The Wireless Ignition Node (WIN) operates similar to an

ignition switch. It has four operating positions, three of

which are detented and one spring-loaded. The detented

positions are OFF, ACC, and ON. The START position is

a spring-loaded momentary contact position. When re-

leased from the START position, the switch automatically

returns to the detented ON position.

Integrated Ignition Key

The integrated ignition key operates the ignition switch.

It also contains the Remote Keyless Entry (RKE) trans-

mitter and a valet key, which stores in the rear of the

transmitter.

WIN Ignition Positions

12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

The valet key allows for entry into the vehicle should the

battery in the vehicle or the transmitter go dead. The

valet key is also for locking the glove box. You can keep

the valet key with you when valet parking.

To remove the valet key from the transmitter, slide the

mechanical latch at the top of the transmitter sideways

with your thumb and then pull the key out with your

other hand.

NOTE: You can insert the double-sided valet key into

the lock cylinder with either side up.

Tip Start Feature

1. Do not press the accelerator pedal during this process.

Valet Key Removal

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13

2

2. Insert the integrated ignition key into the ignition

switch.

3. Turn the ignition switch to the START position and

release it as soon as the starter engages.

The starter motor will continue to run and will disengage

automatically when the engine begins running.

Ignition Key Removal

Place the gear selector lever in PARK. Turn the ignition

key to the OFF position and then remove the key.

NOTE: Power Window switches will also remain active

for up to 90 seconds after the ignition switch has been

turned OFF, depending upon the accessory delay setting.

Opening the front door will cancel this feature.

WARNING!

NEVER leave children alone in a vehicle. Leaving

unattended children in a vehicle is dangerous for a

number of reasons. A child or others could be seri-

ously or fatally injured. Don’t leave the key in the

ignition. A child could operate power windows,

other controls, or move the vehicle

CAUTION!

An unlocked car is an invitation to thieves. Always

remove the key from the ignition and lock all doors

when leaving the vehicle unattended.

14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Key-In-Ignition Reminder

If you open the driver’s door with the integrated ignition

key in the ignition, a chime will sound to remind you to

remove the key.

NOTE: The Key-In-Ignition reminder only sounds

when the integrated ignition key is placed in the OFF or

ACC position.

SENTRY KEYT IMMOBILIZER SYSTEM

The Sentry Keyt Immobilizer system prevents unautho-

rized vehicle operation by disabling the engine. The

system does not need to be armed or activated. Operation

is automatic, regardless of whether the vehicle is locked

or unlocked.

The system uses the factory-mated Remote Keyless Entry

(RKE) transmitter with integrated key and Wireless Igni-

tion Node (WIN) to prevent unauthorized vehicle opera-

tion. Therefore, only RKE transmitters that are pro-

grammed to the vehicle can be used to start and operate

the vehicle. The system will not allow the engine to crank

if an invalid RKE transmitter is used to operate the

ignition switch.

After turning the ignition switch to the ON position, the

Vehicle Security Alarm Indicator Light located on the

instrument cluster will turn on for three seconds for a

bulb check. If the light remains on after the bulb check, it

indicates that there is a problem with the electronics. In

addition, if the light begins to flash after the bulb check,

it indicates that someone used an invalid RKE transmitter

to start the engine. Either of these conditions will result in

the engine being shut off after two seconds.

If the Vehicle Security Alarm Indicator Light, located on

the instrument cluster, turns on during normal vehicle

operation (vehicle running for longer than 10 seconds), it

indicates that there is a fault in the electronics. Should

this occur, have the vehicle serviced as soon as possible.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15

2

NOTE:

•

The Sentry Keyt Immobilizer system is not compatible

with aftermarket remote starting systems. Use of these

systems may result in vehicle starting problems and

loss of security protection.

•

Exxon/Mobil Speedpass™, additional RKE transmit-

ters, or any other transponder-equipped components

on the same key chain will not cause a fault unless the

additional part is physically held against the trans-

mitter being used to start the vehicle. Cell phones,

pagers, or other RF electronics will not cause interfer-

ence with this system.

All of the RKE transmitters provided with your new

vehicle have been programmed to the vehicle electronics.

Replacement Keys

NOTE: Only RKE transmitters that are programmed to

the vehicle electronics can be used to start and operate

the vehicle. Once a transmitter is programmed to a

vehicle, it cannot be programmed to any other vehicle.

CAUTION!

Always remove the keys from the vehicle and lock all

doors when leaving the vehicle unattended.

At the time of purchase, the original owner is provided

with a four-digit Personal Identification Number (PIN).

Keep the PIN in a secure location. This number is

required for authorized dealer replacement of RKE trans-

mitters. Duplication of RKE transmitters may be per-

formed at an authorized dealer or by using the Customer

Key Programming procedure. This procedure consists of

16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

programming a blank transmitter to the vehicle electron-

ics. A blank transmitter is one that has never been

programmed.

NOTE: When having the Sentry Keyt Immobilizer

system serviced, bring all vehicle RKE transmitters with

you to the authorized dealer.

Customer Key Programming

If you have two valid RKE transmitters with integrated

keys, you can program new transmitters to the system by

performing the following steps:

1. Insert the first valid integrated key into the ignition

switch and turn the ignition switch to the ON position for

at least three seconds, but no longer than 15 seconds.

Turn the ignition switch to the OFF position and remove

the first key.

2. Insert the second valid integrated key and turn the

ignition switch to the ON position within 15 seconds.

After 10 seconds, a chime will sound and the Vehicle

Security Alarm Indicator Light will begin to flash. Turn

the ignition switch to the OFF position and remove the

second key.

3. Insert a blank integrated key into the ignition switch

and turn the ignition switch to the ON position within 60

seconds. After 10 seconds, a single chime will sound and

the Vehicle Security Alarm Indicator Light will stop

flashing, turn the ignition switch on again for three

seconds, and then turn it off.

The new integrated key is programmed. The Remote

Keyless Entry (RKE) transmitter will also be pro-

grammed during this procedure.

Repeat this procedure to program up to eight keys. If you

do not have a programmed RKE transmitter with inte-

grated key, contact your authorized dealer for details.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17

2

NOTE: If a programmed key is lost, see your authorized

dealer to have all remaining keys erased from the sys-

tem’s memory. This will prevent the lost key from

starting your vehicle. The remaining keys must then be

reprogrammed. All vehicle keys must be taken to an

authorized dealer at the time of service to be repro-

grammed.

General Information

The Sentry Keyt system complies with FCC rules Part 15

and with RSS-210 of Industry Canada. Operation is

subject to the following conditions:

•

This device may not cause harmful interference.

•

This device must accept any interference that may be

received, including interference that may cause undes-

ired operation.

SECURITY ALARM SYSTEM — IF EQUIPPED

The Vehicle Security Alarm system monitors the vehicle

doors for unauthorized entry and the ignition switch for

unauthorized operation. When the alarm is activated, the

system provides both audible and visual signals. For the

first three minutes the horn will sound and the headlights

and Vehicle Security Alarm Indicator Light will flash

repeatedly. For an additional 15 minutes only the head-

lights and security telltale will flash. The engine will run

only if a valid key is used to start the vehicle.

Rearming Of The System

The Security System will rearm itself after the 15 addi-

tional minutes of headlights and Vehicle Security Alarm

Indicator Light flashing, if the system has not been

disabled. If the condition which initiated the alarm is still

present, the system will ignore that condition and moni-

tor the remaining doors and ignition.

18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Page is loading ...

Dodge 2008 User manual

Related papers

Other documents