Earthquake Sound SUBZERO-15 User manual

Brand
Earthquake Sound
Model
SUBZERO-15
Category
Subwoofers
Type
User manual

This manual is also suitable for

25”
20”
13 1/2"
3”
PORT (6"x16.5"x16.5")
Internal dimensions
18"
Subzero-15
SUBZERO-15
2500 WATTS
Winner of the 2004
Design & Engineering Award
INNOVATIONS
INTERNATIONAL CES
#1
Sealed design for tight bass
Outer dimension shown using 3/4" thick MDF.
#2
Passive tuned design for deep bass small volume
Outer dimension shown using 3/4" thick MDF.
#4
Bass head design for competition
Outer dimension shown using 3/4" thick MDF.
Outer dimension shown using 3/4" thick MDF
#3
Ported design
1” = 2.54 cm
1 cubic foot = 1728 cubic inches
Grille Clearance: 2”
Displacement: .3 Cube Feet
Cut out hole 369mm / 14 1/2"
Mounting
depth
220mm
8 3/4"
SUBZERO-15
17"
18”
15 "
Subzero-15
VB = 3 ft3
FB = optimized with
SLAPS-15 passive
Drone Tuned Box
23”
14”
5”
10 1/2”
18”
16 1/2”
HANDCRAFTED IN USA.
Specifications are subject to change without notice
FOR 44Hz Tuning: Port length equals 26”
FOR 60Hz Tuning: Port length equals 16 1/2”
HOW TO WIRE / FUSE YOUR
SUBZERO TO AN AMPLIFIER
The Subzero subwoofer
comes equipped with 2
voice coils (dual 2x4
ohms), it can be used in
2 , 4 a n d 8 o h m
configurations. The
terminal comes equipped
with fused jumpers, the
voice coil can be easily
configured in series or in
parallel to match the
amplifier in use. It is just a
simple flip of a fuse,
here’s how it works.
PSP (Parallel Series Parallel) Terminal
VC #1
1
- --
S
2
1
2
+ +
PP
DO NOT
USE
VC #2
MONO 2-OHMS
TYPICAL AMPLIFIER TERMINAL
2-channel
2-ohm load
(voice coils in parallel)
(using 2 fuses)
8-GAUGE
8-GAUGE
3mm
Hex-nut
cable
fasteners
1
- --
2
1
2
+ +
S
PP
VC #1
VC #2
CH-1
CH-2
TYPICAL AMPLIFIER TERMINAL
2-channel
2 x 4-ohm load
(voice coils separated)
(no fuses)
8-GAUGE
8-GAUGE
8-GAUGE
8-GAUGE
1
- --
2
1
2
+ +
DO NOT
USE
S
PP
VC #1
VC #2
MONO 8-OHMS
TYPICAL AMPLIFIER TERMINAL
1-channel
8-ohm load
(voice coils in series)
(1 fuse)
8-GAUGE
8-GAUGE
The diagram -on the left side- shows
the PSP terminal in a 2-ohm parallel
configuration (both voice coils are
connected in parallel). Simply place
the 2 fuses in the outer positions in
the fuse placement area. Insert the
negative speaker wire to the far left
insert and one positive to the far right
insert.
This diagram shows the PSP terminal
in a 4-ohm configuration (the two
voice coils are separated). No fuses
are used in this configuration,the voice
coils are powered up separately.
The diagram - on the right side-displays
the PSP in an 8-ohm mode. You will
notice that there is only one fuse in
the center of the fuse placement area.
The voice coils are wired in series.
Insert the negative speaker wire to the
far left insert and one positive to the
far right insert.
Name = EARTHQUAKE SUB-ZERO 15 (broken in) Xmax = 31.7500E-3 M
Note = VI MEASURMENTS Krm = 35.4970E-3 Ohm
Model = TSL Erm = 800.0000E-3
Domain = FreeAir Kxm = 209.1940E-3 H
Shape = Round Exm = 677.0000E-3
Profile = Cone Rms = 4.4866 N·S/M
Fmd = 3.0000 KA Mms = 369.4390E-3 Kg
Qmd = 1.0000 Cms = 114.6000E-6 M/N
Flp = 8.0000 KA Vas = 129.6534E-3 M³
Qlp = 2.0000 Fo = 24.4600 Hz
Znom = 8.0000 Ohm Qms = 12.6551
Revc = 7.8000 Ohm Qes = 0.3095
Sd = 89.0000E-3 M² Qts = 0.3021
Mmd = 354.1806E-3 Kg BL = 37.8262 T·M
Pmax = 1.0000E3 W Levc = 12.4090E-3 H
Rtvc = 250.0000E-3 °C/W SPLo = 89.7098 dB
Xgap = 12.7000E-3 M No = 587.7000E-3 %
Xcoil = 76.2000E-3 M
Electro Mechanical Parameters
  • Page 1 1
  • Page 2 2
  • Page 3 3

Earthquake Sound SUBZERO-15 User manual

Brand
Earthquake Sound
Model
SUBZERO-15
Category
Subwoofers
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents