BEC 5200 Series Owner's manual

5200 Series

(802.11g) ADSL2+ Modem/Router

User’s Manual

ii

Chapter 1 ................................................................................................ 1

1.1 Introducing the 5200 Series................................................... 1

1.2 Features of the 5200 Series ..................................................3

1.3 Applications for the 5200 Series............................................6

Chapter 2 ................................................................................................ 7

2.1 Important note for using the 5200 Series............................... 7

2.2 Package Contents ................................................................. 7

2.3 The Front LEDs .....................................................................8

2.4 The Rear Ports ......................................................................9

2.5 Cabling ................................................................................10

Chapter 3 .............................................................................................. 11

3.1 Before Configuration.............................................................11

3.2 Factory Default Settings ......................................................16

3.3 LAN and WAN Port Addresses............................................17

3.4 Information from your ISP.................................................... 17

3.5 Configuring with your Web Browser .................................... 18

Chapter 4 .............................................................................................. 19

4.1 Quick Start...........................................................................20

4.2 Interface Setup .................................................................... 24

4.3 Advanced Setup .................................................................. 33

4.4 Access Management ........................................................... 43

4.5 Maintenance........................................................................49

4.6 Status...................................................................................54

Chapter 5 .............................................................................................. 59

APPENDIX............................................................................................. 61

Chapter 1

Introduction the 5200 Series

1.1 Introducing the 5200 Series

Welcome to the BEC 5200 Series ADSL2+ Modem/Router. Your BEC router is an

“all-in-one” unit, combining an ADSL modem, ADSL router and Ethernet network switch,

providing everything you need to get the machines on your network connected to the

Internet over your ADSL broadband connection.

The 5200 Series complies with ADSL2+ standards for worldwide deployment and supports

downstream rates of up to 24 Mbps and upstream rates of up to 1 Mbps. It is designed for

small office, home office and residential users, enabling even faster speed Internet

connections. User can enjoy ADSL services and broadband multimedia applications such as

interactive gaming, video streaming and real-time audio much easier and faster than ever

before.

The product supports PPPoA (RFC 2364 – PPP (Point-to-Point Protocol) over ATM

Adaptation Layer 5), RFC 1483 encapsulation over ATM (bridged or routed), PPP over

Ethernet (RFC 2516), and IPoA (RFC1577) to establish a connection with ISP. The product

also supports VC-based and LLC-based multiplexing.

It is the perfect solution to connect a small group of PCs to a high-speed broadband Internet

connection. Multi-users can have high-speed Internet access simultaneously.

This product also serves as an Internet firewall, protecting your network from being

accessed by outside users. Not only provide the natural firewall function (Network Address

Translation, NAT), it also provides rich firewall features to secure user’s network. All

incoming data packets are monitored and filtered. Besides, it can also be configured to

block internal users from accessing to the Internet.

The product provides two levels of security support. First, it masks LAN users’ IP addresses

which are invisible to outside users on the Internet, making it much more difficult for a hacker

2

to target a machine on your network. Secondly, it can block and redirect certain ports to limit

the services that outside users can access. For example, to ensure that games and other

Internet applications will run properly, user can open some specific ports for outside users to

access internal services in network.

Integrated DHCP (Dynamic Host Control Protocol) services, client and server, allow multiple

users to get their IP addresses automatically on boot up from the product. Simply set local

machines as a DHCP client to accept a dynamically assigned IP address from DHCP server

and reboot. Each time local machine is powered up; the router will recognize it and assign

an IP address to instantly connect it to the

LAN.

For advanced users, Virtual Service function allows the product to provide limited visibility to

local machines with specific services for outside users. An ISP (Internet Service Providers)

provided IP address can be set to the product and then specific services can be rerouted to

specific computers on the local network. For instance, a dedicated web server can be

connected to the Internet via the product and then incoming requests for HTML that are

received by the product can be rerouted to the dedicated local web server, even though the

server now has a different IP address. In this example, the product is on the Internet and

vulnerable to attacks, but the server is protected.

Virtual Server can also be used to re-task services to multiple servers. For instance, the

product can be set to allow separated FTP, Web, and Multiplayer game servers to share the

same Internet-visible IP address while still protecting the servers and LAN users from

hackers.

3

1.2 Features of the 5200 Series

ADSL Multi-Mode Standard

supports downstream rates of up to 24 Mbps and upstream rates of up to 1 Mbps. It

also supports rate management that allows ADSL subscribers to select an Internet

access speed suiting their needs and budgets. It is compliant with Multi-Mode standard

(ANSI T1.413, Issue 2; G.dmt(G.992.1); G.lite(G992.2)), G.hs (G994.1), G.dmt.bis

(G.992.3), G.dmt.bisplus (G.992.5)). The Annex A and B are supported the same H/W

platforms.

Wireless Ethernet 802.11g (5200G only)

With built-in 802.11g access point for extending the communication media to WLAN

while providing the WEP, WPA and WPA2 for securing your wireless networks.

Fast Ethernet Switch

A 10/100Mbps fast Ethernet switch is built in with automatic switching between MDI

and MDI-X for 10Base-T and 100Base-TX ports. An Ethernet straight or cross-over

cable can be used directly for auto detection.

Multi-Protocol to Establish A Connection

Supports PPPoA (RFC 2364 - PPP over ATM Adaptation Layer 5), RFC 1483

encapsulation over ATM (bridged or routed), PPP over Ethernet (RFC 2516) and IPoA

(RFC1577) to establish a connection with the ISP. The product also supports

VC-based and LLC-based multiplexing.

Quick Installation Wizard

Supports a WEB GUI page to install this device quickly. With this wizard, end users can

enter the information easily which they get from their ISP, then surf the Internet

immediately.

Universal Plug and Play (UPnP) and UPnP NAT Traversal

This protocol is used to enable simple and robust connectivity among stand-alone

devices and PCs from many different vendors. It makes network simple and

affordable for users. UPnP architecture leverages TCP/IP and the Web to enable

seamless proximity networking in addition to control and data transfer among

networked devices. With this feature enabled, users can now connect to Net meeting

or MSN Messenger seamlessly.

Network Address Translation (NAT)

Allows multi-users to access outside resources such as the Internet simultaneously

with one IP address/one Internet access account. Many application layer gateway

4

(ALG) are supported such as web browser, ICQ, FTP, Telnet, E-mail, News,

Net2phone, Ping, NetMeeting, IP phone and others.

Firewall

Supports simple firewall with NAT technology and provides option for blocking access

from Internet, like Telnet, FTP, WEB, SNMP and IGMP.

Domain Name System (DNS) relay

Provides an easy way to map the domain name (a friendly name for users such as

www.yahoo.com) and IP address. When a local machine sets its DNS server with this

router’s IP address, every DNS conversion request packet from the PC to this router

will be forwarded to the real DNS in the outside network.

Dynamic Domain Name System (DDNS)

The Dynamic DNS service allows you to alias a dynamic IP address to a static

hostname. This dynamic IP address is the WAN IP address. For example, to use the

service, you must first apply for an account from a DDNS service like

http://www.dyndns.org/.

PPP over Ethernet (PPPoE): Provides embedded PPPoE client function to establish a

connection. Users can get greater access speed without changing the operation

concept, sharing the same ISP account and paying for one access account. No PPPoE

client software is required for local computer. The Automatic Reconnect and Disconnect

Timeout (Idle Timer) functions are provided, too.

Virtual Server: User can specify some services to be visible from outside users. The

router can detect incoming service request and forward it to the specific local computer

to handle it. For example, user can assign a PC in LAN acting as WEB server inside and

expose it to the outside network. Outside user can browse inside web server directly

while it is protected by NAT. A DMZ host setting is also provided to a local computer

exposed to the outside network, Internet.

Users can specify some services to be visible from outside users. The router can

detect incoming service requests and forward either a single port or a range of ports to

the specific local computer to handle it. For example, a user can assign a PC in the

LAN acting as a WEB server inside and expose it to the outside network. Outside users

can browse inside web servers directly while it is protected by NAT. A DMZ host setting

is also provided to a local computer exposed to the outside network, Internet.

Dynamic Host Configuration Protocol (DHCP) client and server

In the WAN site, the DHCP client can get an IP address from the Internet Service

Provider (ISP) automatically. In the LAN site, the DHCP server can allocate a range of

5

client IP addresses and distribute them including IP address, subnet mask as well as

DNS IP address to local computers. It provides an easy way to manage the local IP

network.

RIP1/2 Routing

Supports RIP1/2 routing protocol for routing capability.

Simple Network Management Protocol (SNMP)

It is an easy way to remotely manage the router via SNMP.

Web based GUI

Supports web based GUI for configuration and management. It is user-friendly and

comes with on-line help. It also supports remote management capability for remote

users to configure and manage this product.

Firmware Upgradeable

Device can be upgraded to the latest firmware through the WEB based GUI.

6

1.3 Applications for the 5200 Series

7

Chapter 2

Installing the 5200 Series

2.1 Important note for using the 5200 Series

2.2 Package Contents

5200 Series ADSL2+ Router

RJ-11 ADSL/telephone Cable (1.8M)

Ethernet (CAT-5 LAN) Cable (2M Straight)

AC-DC power adapter (12V DC, 1A)

9 Place the 5200 Series on a stable surface.

9 Only use the power adapter that comes with the package. Using

a different voltage rating power adaptor may damage the router.

Attention

9 Do not use the 5200 Series in high humidity or high

temperatures.

9 Do not use the same power source for the 5200 Series as

other equipment.

9 Do not open or repair the case yourself. If the 5200 Series is

too hot, turn off the power immediately and have it repaired at

a qualified service center.

9

A

void usin

g

this

p

roduct and all accessories outdoors.

Warning

8

2.3 The Front LEDs

5200

5200S

5200G

LED Meaning

1 PPP : Lit steady when there is a PPPoA / PPPoE connection.

2 ADSL:

Lit when successfully connected to an ADSL DSLAM

(“linesync”).

3

LAN Port

1-4:

Lit when connected to an Ethernet device.

Green for 100Mbps; Orange for 10Mbps.

Blinking when data is Transmitted / Received.

4

WLAN：

(5200G

only)

Lit green when the wireless connection is established.

Flashes when sending/receiving data.

5 SYS : Lit when the system is ready.

6 PWR : Lit when power is ON.

9

2.4 The Rear Ports

5200

5200S

5200G

Port Meaning

1

PWR

Connect the supplied power adapter to this jack.

2 RESET

After the device is powered on, press it to reset the device or

restore to factory default settings.

0-3 seconds: reset the device

6 seconds above: restore to factory default settings (this is used

when you can not login to the router, e.g. forgot the password)

3

LAN

Connect a UTP Ethernet cable (Cat-5 or Cat-5e) to one of the

four LAN ports when connecting to a PC or an office/home

network of 10Mbps or 100Mbps.

4

ADSL

(LINE)

Connect the supplied RJ-11 (“telephone”) cable to this port when

connecting to the ADSL/telephone network.

5

Power

Switch

Power ON/OFF switch

4

3

2

4

2

1

3

1

2

3

4

5

10

2.5 Cabling

One of the most common causes of problems is bad cabling or ADSL line(s). Make sure that

all connected devices are turned on. On the front of the product is a bank of LEDs. Verify that

the LAN Link and ADSL line LEDs are lit. If they are not, verify that you are using the proper

cables.

Ensure that all other devices connected to the same telephone line as your BEC router (e.g.

telephones, fax machines, analogue modems) have a line filter connected between them

and the wall socket (unless you are using a Central Splitter or Central Filter installed by a

qualified and licensed electrician), and ensure that all line filters are correctly installed and

the right way around. Missing line filters or line filters installed the wrong way around can

cause problems with your ADSL connection, including causing frequent disconnections

11

Chapter 3

Basic Installation

The router can be configured with your web browser. A web browser is included as a

standard application in the following operating systems: Windows 98/NT/2000/XP/Me, MAC,

Linux, etc. The product provides a very easy and user-friendly interface for configuration.

3.1 Before Configuration

PCs must have an Ethernet interface installed properly and be connected to the router either

directly or through an external repeater hub, and have TCP/IP installed and configured to

obtain an IP address through a DHCP server or a fixed IP address that must be in the same

subnet as the router. The default IP address of the router is 192.168.1.254 and the subnet

mask is 255.255.255.0 (i.e. any attached PC must be in the same subnet, and have an IP

address in the range of 192.168.1.1 to 192.168.1.253). The best and easiest way is to

configure the PC to get an IP address automatically from the router using DHCP. If you

encounter any problems accessing the router’s web interface it may also be advisable to

uninstall any kind of software firewall on your PCs, as they can cause problems accessing

the 192.168.1.254 IP address of the router. Users should make their own decisions on how

to best protect their network.

Please follow the steps below for your PC’s network environment installation. First of all,

please check your PC’s network components. The TCP/IP protocol stack and Ethernet

network adapter must be installed. If not, please refer to your Windows-related or other

operating system manuals.

Any TCP/IP capable workstation can be used to communicate with or

through the 5200 Series. To configure other types of workstations,

please consult the manufacturer’s documentation.

12

Configuring PC in Windows XP

1. Go to Start / Control Panel (in Classic

View). In the Control Panel, double-click

on Network Connections

2. Double-click Local Area Connection.

3. In the Local Area Connection Status

window, click Properties.

4. Select Internet Protocol (TCP/IP) and

click Properties.

5. Select the Obtain an IP address

automatically and the Obtain DNS

server address automatically radio

buttons.

6. Click OK to finish the configuration.

13

Configuring PC in Windows 2000

1. Go to Start / Settings / Control Panel.

In the Control Panel, double-click on

Network and Dial-up Connections.

2. Double-click Local Area Connection.

3. In the Local Area Connection Status

window click Properties.

4. Select Internet Protocol (TCP/IP) and

click Properties.

5. Select the Obtain an IP address

automatically and the Obtain DNS

server address automatically radio

buttons.

6. Click OK to finish the configuration.

14

Configuring PC in Windows 98/Me

1.Go to Start / Settings / Control Panel.

In the Control Panel, double-click on

Network and choose the

Configuration tab.

2.Select TCP/IP ->NE2000 Compatible,

or the name of your Network Interface

Card (NIC) in your PC.

3.Select the Obtain an IP address

automatically radio button.

4.Then select the DNS Configuration tab.

5.Select the Disable DNS radio button

and click OK to finish the configuration.

15

Configuring PC in Windows NT4.0

1. Go to Start / Settings / Control Panel.

In the Control Panel, double-click on

Network and choose the Protocols tab.

2.Select TCP/IP Protocol and click

Properties.

3.Select the Obtain an IP address from a

DHCP server radio button and click OK.

16

3.2 Factory Default Settings

Before configuring your, you need to know the following default settings.

Web Interface:

Username: admin

Password: admin

LAN Device IP Settings:

IP Address: 192.168.1.254

Subnet Mask: 255.255.255.0

ISP setting in WAN site:

PPPoE

DHCP server:

DHCP server is enabled.

Start IP Address: 192.168.1.100

IP pool counts: 100

3.2.1 Username and Password

The default username and password are “admin” and “admin” respectively.

Attention

If you ever forget the password to log in, you may press the RESET

button up to 6 seconds to restore the factory default settings.

Attention

17

3.3 LAN and WAN Port Addresses

The parameters of LAN and WAN ports are pre-set in the factory. The default values are

shown below.

LAN Port WAN Port

IP address

192.168.1.254

Subnet Mask

255.255.255.0

DHCP server function

Enabled

IP addresses for

distribution to PCs

100 IP addresses continuing from

192.168.1.100 through

192.168.1.199

The PPPoE function is

enabled to

automatically get the

WAN port

configuration from the

ISP, but you have to

set the username and

password first.

3.4 Information from your ISP

Before configuring this device, you have to check with your ISP (Internet Service Provider)

what kind of service is provided such as PPPoE, PPPoA, RFC1483, or IPoA.

Gather the information as illustrated in the following table and keep it for reference.

PPPoE VPI/VCI, VC-based/LLC-based multiplexing, Username, Password,

Service Name, and Domain Name System (DNS) IP address (it can

be automatically assigned by your ISP when you connect or be set

manually).

PPPoA VPI/VCI, VC-based/LLC-based multiplexing, Username, Password,

and Domain Name System (DNS) IP address (it can be

automatically assigned by your ISP when you connect or be set

manually).

RFC1483 Bridged VPI/VCI, VC-based/LLC-based multiplexing to use Bridged Mode.

RFC1483 Routed VPI/VCI, VC-based/LLC-based multiplexing, IP address, Subnet

mask, Gateway address, and Domain Name System (DNS) IP

address (it is fixed IP address).

18

3.5 Configuring with your Web Browser

Open your web browser, enter the IP address of your router, which by default is

192.168.1.254, and click “Go”, a user name and password window prompt will appear. The

default username and password are “admin” and “admin”.

Congratulation! You are now successfully logon to the 5200 Series ADSL Router!

Page is loading ...

BEC 5200 Series, 5200W Owner's manual

Related papers

Other documents