Echo ES-250AA User manual

Brand: Echo

Model: ES-250AA

Category: Air blowers/dryers

Type: User manual

SHRED'N'VAC

Operator's Manual

MODEL ES-250

WARNING

Users of this equipment risk injury to themselves and others if the unit is used im-

properly and/or safety precautions are not followed. ECHO provides an operator’s

manual. It must be read and understood for proper and safe operation. Failure to do

so could result in serious injury.

X750019420

03/11

X7501182800

Table of ConTenTs

Introduction ................................................................2

- The Operator's Manual .......................................2

Safety .........................................................................3

- Manual Safety Symbols and Important

Information .........................................................3

- International Symbols ......................................... 3

- Personal Condition and Safety Equipment ......... 3

- Equipment Check ................................................6

Emission Control .......................................................6

Description ................................................................. 7

Contents .....................................................................8

Assembly....................................................................9

- Install Blower Pipes ............................................ 9

- Vacuum/Shredding Application ........................10

Operation ..................................................................10

- Fuel ...................................................................10

- Starting Cold Engine .........................................12

- Starting Warm Engine .......................................13

- Stopping Engine ................................................13

- Operating Blower ..............................................16

- SHRED'N'VAC

Operation ...............................16

- SHRED'N'VAC

Troubleshooting ....................17

Maintenance ............................................................. 18

- Skill Levels .......................................................18

- Maintenance Intervals .......................................18

- Air Filter ...........................................................19

- Fuel Filter ..........................................................19

- Spark Plug .........................................................20

- Cooling System .................................................20

- Exhaust System .................................................21

- Shredder Blade ..................................................23

- Debris Bag ........................................................23

- Carburetor Adjustment ...................................... 24

- High Altitude Operation .................................24

Troubleshooting .......................................................25

Storage .....................................................................26

Specications ...........................................................27

Warranty Statements ................................................28

Servicing Information ..............................................32

- Parts/Serial Number ..........................................32

- Service ..............................................................32

- ECHO Consumer Product Support ................... 32

- Warranty Card ...................................................32

- Additional or Replacement Manuals ................32

Specications, descriptions and illustrative material in this

literature are as accurate as known at the time of publica-

tion, but are subject to change without notice. Illustrations

may include optional equipment and accessories, and may

not include all standard equipment.

InTroduCTIon

Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-

job dependability. Read and understand this manual. You will nd it easy to use and full of helpful operating tips and

SAFETY messages.

The operaTor's manual

Read and understand this manual before operation. Keep it in a safe

place for future reference. It contains specications and information

for operation, starting, stopping, maintenance, storage and assembly

specic to this product.

Power Blower

Operator's Manual

MODEL PB-251

X75300

09/06

X753118

WARNING

Read rules for safe operation and instructions carefully. ECHO provides this Operator's

Manual, which must be read and understood for proper and safe operation.

PB251ef_091206.pmd

Power Blower

Operator's Manual

MODEL PB-250

WARNING

Read rules for safe operation and instructions carefully. ECHO provides this

Operator's Manual, which must be read and understood for proper and safe opera-

tion.

X750012940

XX/XX

X7501182000

Power Blower

Perator's Manual

safeTy

manual

safeTy symbols and ImporTanT InformaTIon

Throughout this manual and on the product itself, you will nd safety alerts and helpful, informational messages

preceded by symbols or key words. The following is an explanation of those symbols and key words and what they

mean to you.

InTernaTIonal symbols

Symbol

description/application

Symbol form/shape

Symbol

description/application

Symbol form/shape

Read and understand

Operator's Manual.

Fuel and oil mixture

Hot

Surface

Wear eyes, ears and

head protection

Finger Severing

Safety/Alert

Wear hand

protection. Use

two handed.

DO NOT smoke

near fuel.

DO NOT allow

ames or sparks

near fuel.

Wear slip resis-

tant foot wear.

personal CondITIon and safeTy equIpmenT

WARNING

Users of this product risk injury to themselves and others if the unit is used improperly and/or safety precautions are

not followed. Proper clothing and safety gear must be worn when operating unit.

WARNING

The safety alert symbol accompanied by the word

“WARNING” calls attention to an act or condi-

tion which CAN lead to serious personal injury or

death if not avoided.

CIRCLE AND SLASH SYMBOL

This symbol means the specic action

shown is prohibited. Ignoring these prohi-

bitions can result in serious or fatal injury.

CAUTION

The safety alert symbol accompanied by the word

“CAUTION” calls attention to an act or condition

which may lead to minor or moderate personal

injury if not avoided.

NOTE

This enclosed message provides tips for use, care and

maintenance of the unit.

IMPORTANT

The enclosed message provides information neces-

sary for the protection of the unit.

DANGER

The safety alert symbol accompanied by the word

“DANGER” calls attention to an act or condition

which WILL lead to serious personal injury or

death if not avoided.

Symbol

description/application

Symbol form/shape

Symbol

description/application

Symbol form/shape

Carburetor adjustment

- Idle speed

Carburetor adjustment

- High speed mixture

Emergency stop

Carburetor adjustment

- Low speed mixture

Ignition

ON/OFF

Primer bulb

Choke Control

"Cold Start"

Position

(Choke Closed)

Choke Control

"Run"

Position

(Choke Open)

Idle Speed Fast Speed

Physical Condition

Your judgment and physical dexterity may not be good:

• if you are tired or sick,

• if you are taking medication,

• if you have taken alcohol or drugs.

Operate unit only if you are physically and mentally well.

Eye Protection

Wear eye protection that meets ANSI Z87.1 or CE require-

ments whenever you operate the unit.

Hand Protection

Wear no-slip, heavy-duty work gloves to improve your grip

on the blower handle. Gloves also reduce the transmission of

machine vibration to your hands.

Breathing Protection

Wear a facemask to protect against dust.

Hearing Protection

ECHO recommends wearing hearing protection whenever

unit is used.

Vibration and Cold

It is believed that a condition called Raynaud’s Phenomenon, which affects the ngers of certain individuals, may be

brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning sen-

sations, followed by loss of color and numbness in the ngers. The following precautions are strongly recommended,

because the minimum exposure, which might trigger the ailment, is unknown.

• Keep your body warm, especially the head, neck, feet, ankles,

hands, and wrists.

• Maintain good blood circulation by performing vigorous arm

exercises during frequent work breaks, and also by not smoking.

• Limit the hours of operation. Try to ll each day with jobs where

operating the unit or other hand-held power equipment is not

required.

• If you experience discomfort, redness, and swelling of the ngers

followed by whitening and loss of feeling, consult your physician

before further exposing yourself to cold and vibration.

Proper Clothing

Wear snug tting, durable clothing;

• Pants should have long legs, shirts with long sleeves.

• DO NOT WEAR SHORTS,

• DO NOT WEAR TIES, SCARVES, JEWELRY,

or clothing with loose or hanging items that could

become entangled in moving parts or surrounding

growth..

Wear sturdy work shoes with nonskid soles;

• DO NOT WEAR OPEN TOED SHOES,

• DO NOT OPERATE UNIT BAREFOOTED.

Wear no-slip, heavy duty work gloves.

Keep long hair away from engine and air intake. Retain

hair with cap or net.

Hot Humid Weather

Heavy protective clothing can increase operator fatigue

which may lead to heat stroke. Schedule heavy work for

early morning or late afternoon hours when temperatures

are cooler.

WARNING

The ignition components of this machine generate an electromagnetic eld during operation which may interfere

with some pacemakers. To reduce the risk of serious or fatal injury, persons with pacemakers should consult with

their physician and the pacemaker manufacturer before operating this machine. In the absence of such informa-

tion, ECHO does not recommend the use of ECHO products by anyone who has a pacemaker.

Power Blower

Perator's Manual

DANGER

Do not operate this product indoors or in inadequately ventilated

areas. Engine exhaust contains poisonous emissions and can cause

serious injury or death.

Read the Manuals

• Provide all users of this equipment with the Operator’s Manual

and Safety Manual for instructions on Safe Operation.

Clear the Work Area

• Spectators and fellow workers must be warned, and children and

animals prevented from coming nearer than 15 m (50 ft.) while

the unit is in use.

• Take wind conditions into account: avoid open doors and win-

dows.

• Do not point blower at people or animals.

• Review area to be cleared. Look for potential hazards such as

stones or metal objects.

Keep a Firm Grip

• Hold the handle in one hand, with thumb and ngers encircling

the handle.

Keep a Solid Stance

• Maintain footing and balance at all times. Do not stand on slip-

pery, uneven or unstable surfaces. Do not work in odd positions

or on ladders. Do not over reach.

Avoid Hot Surfaces

• Keep exhaust area clear of ammable debris. Avoid contact dur-

ing and immediately after operation.

Repetitive Stress Injuries

It is believed that overusing the muscles and tendons of the ngers, hands, arms, and shoulders may cause soreness,

swelling, numbness, weakness, and extreme pain in those areas. Certain repetitive hand activities may put you at a high

risk for developing a Repetitive Stress Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome (CTS), which

could occur when your wrist swells and squeezes a vital nerve that runs through the area.

Some believe that prolonged exposure to vibration may contribute to CTS. CTS can cause severe pain for months or

even years.

To reduce the risk of RSI/CTS, do the following:

• Avoid using your wrist in a bent, extended, or twisted position.

Instead try to maintain a straight wrist position. Also, when

grasping, use your whole hand, not just the thumb and index

nger.

• Take periodic breaks to minimize repetition and rest your hands.

• Reduce the speed and force with which you do the repetitive

movement.

• Do exercises to strengthen the hand and arm muscles.

• Immediately stop using all power equipment and consult a doc-

tor if you feel tingling, numbness, or pain in the ngers, hands,

wrists, or arms. The sooner RSI/CTS is diagnosed, the more

likely permanent nerve and muscle damage can be prevented.

equIpmenT CheCk

WARNING

Use only ECHO approved attachments. Serious injury may result from the use of a non-approved attachment combi-

nation. ECHO, INC. will not be responsible for the failure of cutting devices, attachments or accessories which have

not been tested and approved by ECHO. Read and comply with all safety instructions listed in this manual and safety

manual.

• Check unit for loose/missing nuts, bolts and screws. Tighten and/or replace as needed.

• Do not use blower if any part is missing or damaged.

• Have repairs done only by an authorized ECHO Service dealer.

• Do not use any attachment, accessory or replacement part unless it is recommended in this Operator's Manual.

An Emission Control Label is located on the unit. (This is an EXAMPLE ONLY; information on label varies by engine

FAMILY).

WARNING

Moving parts can amputate ngers or cause severe injuries. Keep hands, clothing and loose objects away from all

openings.

• A LWAYS stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop

before removing obstructions, clearing debris, or servicing unit.

• DO NOT start or operate unit unless all guards and protective covers are properly assembled to unit.

• NEVER reach into any opening while the engine is running. Moving parts may not be visible through openings.

WARNING

Check fuel system for leaks due to fuel tank damage, especially if the unit is dropped. If damage or leaks are found,

do not use unit, otherwise serious personal injury or property damage may occur. Have unit repaired by an authorized

servicing dealer before using.

PRODUCT EMISSION DURABILITY (EMISSION COMPLIANCE PERIOD)

The 300 hour emission compliance period is the time span selected by the manufacturer certifying the engine emis-

sions output meets applicable emissions regulations, provided that approved maintenance procedures are followed as

listed in the Maintenance Section of this manual.

emIssIon ConTrol (exhausT & evaporaTIve)

EPA 2010 and Later and/or C.A.R.B. TIER III

The emission control system for the engine is EM/TWC (Engine Modication and 3-way Catalyst) and for the fuel tank

the Control System is EVAP (Evaporative Emissions) or N (for nylon tank). Evaporative emission may be applicable to

California models only.

Power Blower

Perator's Manual

desCrIpTIon

Locate the safety decals on your unit. Make sure the decals are legible and that you understand and follow the instruc-

tions on them. If a decal cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDERING

instructions for specic information.

70 Category II

dB(A)

Measured at 50 ft. (15m) per ANSI B175.2

Hot Decal (near mufer and engine)

General Warning Decal (located on blower housing)

Sound Label (located on blower housing)

1. SAFETY DECAL - Lists important safety precautions.

2. STOP SWITCH - "SLIDE SWITCH" mounted on top of handle. Push forward to start and run. Slide back to stop.

3. SPARK PLUG - Provides spark to ignite fuel mixture.

4. FUEL TANK CAP - Covers and seals fuel tank.

5. RECOIL STARTER HANDLE - Pull recoil handle slowly until recoil starter engages, then quickly and rmly.

When engine starts, return handle slowly. DO NOT let handle snap back or damage to unit will occur.

6. CHOKE - Choke is located on top of the air cleaner. Move choke lever to "COLD START" ( ) to close choke

for cold starting. Move choke lever to "RUN" position to open choke.

7. PURGE BULB - Pumping purge bulb before starting engine draws fresh fuel from the fuel tank, purging air from

the carburetor. Pump purge bulb until fuel is visible and ows freely in the clear fuel tank return line. Pump purge

bulb an additional 4 or 5 times.

8. SPARK ARRESTOR MUFFLER OR SPARK ARRESTOR MUFFLER WITH CATALYST -The mufer or

catalytic mufer controls exhaust noise and emission. The spark arrestor screen prevents hot, glowing particles of

carbon from leaving the mufer. Keep exhaust area clear of ammable debris.

9. BLOWER PIPES - Exclusive positive locking system.

10. SAFETY DECAL - Lists important safety precautions.

11. SAFETY DECAL - Lists important safety precautions.

12. THROTTLE POSITION LEVER - Pull back to increase engine speed. Friction washers maintain throttle lever

setting.

13. THROTTLE TRIGGER - Spring loaded to return to idle when released. During acceleration, press trigger gradu-

ally for best operating technique.

14. AIR CLEANER - Contains replaceable air lter element.

ConTenTs

1 - Power Head

1 - Blower Pipe (upper)

1 - Blower Pipe (lower)

1 - SHRED 'N' VAC

Suction Tube

1 - Elbow Pipe

1 - Debris Bag

1 - Operator's Manual

1 - Warranty Registration Card

1 - Echo Power Blend X

2-stroke oil sample

Power Blower

Operator's Manual

MODEL PB-251

X75300

09/06

X753118

WARNING

Read rules for safe operation and instructions carefully. ECHO provides this Operator's

Manual, which must be read and understood for proper and safe operation.

PB251ef_091206.pmd

Power Blower

Operator's Manual

MODEL PB-250

WARNING

Read rules for safe operation and instructions carefully. ECHO provides this

Operator's Manual, which must be read and understood for proper and safe opera-

tion.

X750012940

XX/XX

X7501182000

Power Blower

Perator's Manual

assembly

WARNING

Never perform maintenance or assembly procedures with engine

running or serious personal injury may result.

blower applICaTIon

Install Blower Pipes

1. Stand unit upright on blower base.

2. Align locking ribs (A) on upper pipe with recesses (B) in fan

case. Assure short locking rib (C) faces downward. Slide upper

pipe into fan case until a clicking sound is heard.

3. Align tabs (D) with grooves (E) and slide lower blower pipe over

upper pipe until there is light resistance. Do not force connection.

4. Hold upper pipe, and turn lower pipe clockwise, engaging posi-

tive locking channels until connection is rm. Do not force con-

nection.

NOTE

Blower use will eventually loosen pipe connections. Exclusive

positive locking system allows pipes to be tightened. If loosening

occurs, remove lower straight pipe, and install according to instruc-

tions 3 & 4.

blower pipe (upper)

blower pipe (lower)

vaCuum/shreddIng applICaTIon

Remove Blower Pipes

1. Insert screwdriver (F) into hole located near lock symbol (G) to

release pipe lock.

CAUTION

Screwdriver tip may stick out opposite side of locking hole.

2. Pull pipe out of fan case.

3. Remove screwdriver.

Install Vacuum Tube

1. Turn knob (I) counter clockwise until hinged housing cover is

free to open for vacuum tube installation.

2. Opening housing cover, slide recess (J) on vacuum tube into

locking rib (K), and turn the vacuum tube clockwise so that it is

locked.

NOTE

Engine will not start/operate unless safety interlock switch (K) is

activated by the vacuum tube.

Power Blower

Perator's Manual

Install Bag

1. Stand unit upright on blower base.

2. Align locking ribs (A) on elbow pipe with recesses (B) in fan

case. Assure short locking rib (C) faces downward. Slide elbow

pipe into fan case until a clicking sound is heard.

3. Place debris bag opening over ared end of elbow (D), and cinch

bag securely with Velcro strap (E).

Fuel Requirements

Gasoline - Use 89 Octane [R+M/2] (mid grade or higher) gasoline known to be good quality. Gasoline may contain up to

10% Ethanol (grain alcohol) or 15% MTBE (methyl tertiary-butyl ether). Gasoline containing methanol (wood alcohol)

is NOT approved.

Two Stroke Oil - A two-stroke engine oil meeting ISO-L-EGD (ISO/CD 13738) and J.A.S.O. FD Standards must be

used. Echo brand premium Power Blend X

Universal 2-Stroke Oil meets these standards. Engine problems due to

inadequate lubrication caused by failure to use an ISO-L-EGD (ISO/CD 13738) and J.A.S.O. FD certied oil, such as

Echo premium Power Blend X

, will void the two-stroke engine warranty.

IMPORTANT

Echo premium Power Blend X

Universal 2-Stroke Oil may be mixed at 50:1 ratio for application in all Echo en-

gines sold in the past regardless of ratio specied in those manuals.

WARNING

Moving parts can amputate ngers or cause severe injuries. Keep hands, clothing and loose objects away from all

openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop

before removing obstructions, clearing debris, or servicing unit. Blower housing may contain shredder blades and

other sharp edges that can cause serious injuries if touched, even if engine is off and blades are not moving. Wear

gloves to protect hands from sharp edges and hot surfaces.

fuel

NOTICE: Use of unmixed, improperly mixed, or fuel older than 90 days, (stale fuel), may cause hard starting, poor

performance, or severe engine damage and void the product warranty. Read and follow instructions in the Storage

section of this manual.

WARNING

Alternative fuels, such as E-15 (15% ethanol), E-85 (85% ethanol) or any fuels not meeting ECHO requirements are

NOT approved for use in ECHO 2-stroke gasoline engines. Use of alternative fuels may cause performance prob-

lems, loss of power, overheating, fuel vapor lock, and unintended machine operation, including, but not limited to,

improper clutch engagement. Alternative fuels may also cause premature deterioration of fuel lines, gaskets, carbu-

retors and other engine components.

operaTIon

WARNING

Operation of this equipment may create sparks that can start res around dry vegetation. This unit is equipped

with a spark arrestor and a spark arrestor may be required. The operator should contact local re agencies for

laws or regulations relating to re prevention requirements.

Power Blower

Perator's Manual

Mixing Instructions

1. Fill an approved fuel container with half of the required amount

of gasoline.

2. Add the proper amount of 2-stroke oil to gasoline.

3. Close container and shake to mix oil with gasoline.

4. Add remaining gasoline, close fuel container, and remix.

IMPORTANT

Spilled fuel is a leading cause of hydrocarbon emissions. Some

states may require the use of automatic fuel shut-off containers

to reduce fuel spillage.

After use

• DO NOT store a unit with fuel in its tank. Leaks can occur. Return

unused fuel to an approved fuel storage container.

Storage - Fuel storage laws vary by locality. Contact your local gov-

ernment for the laws affecting your area. As a precaution, store fuel in

an approved, airtight container. Store in a well-ventilated, unoccupied

building, away from sparks and ames.

Handling Fuel

DANGER

Fuel is VERY ammable. Use extreme care when mixing, storing or handling or serious personal injury may result.

• Use an approved fuel container.

• DO NOT smoke near fuel.

• DO NOT allow ames or sparks near fuel.

• Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equalize.

• NEVER refuel a unit when the engine is HOT or RUNNING!

• DO NOT ll fuel tanks indoors. ALWAYS ll fuel tanks outdoors over bare ground.

• DO NOT overll fuel tank. Wipe up spills immediately.

• Securely tighten fuel tank cap and close fuel container after refueling.

• Inspect for fuel leakage. If fuel leakage is found, do not start or operate unit until leakage is repaired.

• Move at least 3m (10 ft.) from refueling location before starting the engine.

IMPORTANT

Stored fuel ages. Do not mix more

fuel than you expect to use in thirty

(30) days, ninety (90) days when a

fuel stabilizer is added.

IMPORTANT

Stored two-stroke fuel may separate.

ALWAYS shake fuel container thor-

oughly before each use.

sTarTIng Cold engIne

1. Stop Switch

Move stop switch button (A) away from the STOP position.

2. Throttle Position Lever

Move throttle position lever (B) midway between idle and full

throttle positions.

3. Choke

Move choke (C) to Cold Start ( ) Position.

4. Purge Bulb

Pump purge bulb (D) until fuel is visible and ows freely in the

clear fuel tank return line.

IMPORTANT

Recoil starter: Use short pulls - only 1/2 ~ 2/3 of rope for start-

ing. Do not allow the rope to snap back in. Always hold the unit

rmly.

5. Recoil Starter

Place the unit on a at, clear area. Firmly grasp throttle grip with

left hand and rapidly pull recoil starter handle/rope (E) until en-

gine res , or maximum 5 pulls.

6. Choke

Move choke lever (C) to Run position, and if necessary, restart

engine.

NOTE

If engine does not start after 5 pulls, repeat instructions 3-6.

7. After engine warm up, gradually depress throttle trigger to in-

crease engine RPM to operating speed.

NOTE

Allow engine to warm up 3 minutes before use.

Power Blower

Perator's Manual

sTarTIng warm engIne

The starting procedure is the same as Cold Start except DO NOT close

the choke.

1. Stop Switch

Move stop switch button (A) away from the STOP position.

2. Throttle Position Lever

Move throttle position lever (B) midway between idle and full

throttle positions.

3. Purge Bulb

Pump purge bulb (D) until fuel is visible and ows freely in the

clear fuel tank return line.

4. Recoil Starter

Place the unit on a at, clear area. Firmly grasp throttle grip with

left hand and rapidly pull recoil starter handle/rope (E) until en-

gine res.

IMPORTANT

Recoil starter: Use short pulls - only 1/2 ~ 2/3 of rope for start-

ing. Do not allow the rope to snap back in. Always hold the unit

rmly.

NOTE

If engine does not start after 5 pulls, use Cold Start Procedure.

sToppIng engIne

1. Throttle Trigger/Throttle Position Lever

Release throttle trigger (F). Move throttle position lever (B)

forward to idle position and allow engine to return to idle before

shutting off engine.

2. Stop Switch

Move stop switch (A) to “STOP” position.

WARNING

If engine does not stop when stop switch is moved to STOP posi-

tion, close choke - COLD START ( ) position - to stall engine.

Have your ECHO dealer repair stop switch before using blower

again.

operaTIng blower

WARNING

Engine exhaust IS HOT, and contains Carbon Monoxide (CO), a

poison gas. Breathing CO can cause unconsciousne, serious injury,

or death. Exhaust can cause serious burns. ALWAYS position unit

so that exhaust is directed away from your face and body.

WARNING

Always wear safety glasses, hearing protection and a face lter

mask or serious personal injury may result. Do not point the blower

pipe in the direction of people or pets.

IMPORTANT

Use reduced speed only when performing light-duty tasks or

to comply with local noise regulations. Continuous low speed

operation may allow fuel/oil residue to build-up on the piston

and cause rapid build-up of carbon on the spark arrestor screen,

resulting in overheating and engine damage. To reduce harmful

build-up, run engine at wide open throttle for at least 5 minutes

every hour, and inspect/clean the spark arrestor screen after ap-

proximately 40 hours of operation.

Read the Safety Section carefully.

IMPORTANT

To avoid engine damage due to over-revving, do not block

blower pipe.

1. Use only during appropriate hours.

2. Allow the engine to warm up at a fast idle for a few minutes.

3. Control engine speed with throttle trigger (F), or for continu-

ous use, set engine speed with throttle position lever (B). Rotate

throttle position lever forward for lower speed, back for higher

speed.

4. Use lower speed to blow debris from hard surfaces.

5. Additional speed may be necessary to clean debris, snow, etc.

from lawns and owerbeds.

NOTE

Never use a higher speed setting than necessary to perform a task.

Remember, the higher the engine speed, the louder the blower

noise. Minimize dust by using blower at lower speeds. Keep debris

on your property.

Be Smart - be a good neighbor.

Power Blower

Perator's Manual

1. Adjust debris bag strap to support bag on operator’s shoulder.

Bag must not be folded at intake area, or intake will clog. Further

adjustment may be necessary as the debris bag lls and becomes

heavier.

2. Grip throttle control handle with left hand, and lower handle/

stand with right hand.

3. Operate unit with beveled end of tube facing downward. Keep

tube opening close to material being vacuumed for best results.

4. Empty bag when debris level reaches intake opening. To empty

bag, move stop switch to “Stop” position, and wait for blower

to stop running. Loosen Velcro strap at elbow and slide bag off

elbow. Open other end of bag, and empty contents. Close bag,

and reattach to blower. Secure bag with Velcro strap.

shred'n' vaC

operaTIon

WARNING

Flying debris hazard. Never operate unit as a vacuum unless

discharge elbow is installed and debris bag is securely cinched to

elbow. Failure to follow instructions can result in serious injuries.

NOTE

Vacuum action works best at higher

engine speeds. Avoid using vacuum in

areas where rocks or other large, hard

debris may be vacuumed into unit. Clear

these areas with blower rst, blowing

light debris into a pile. Use attachment

to vacuum pile.

shred 'n' vaC

TroubleshooTIng

Problem Cause Remedy

Unit runs, but doesn’t vacuum or

has poor suction

Elbow or debris bag clogged

Check elbow and debris bag, and clear

as needed. Make sure bag is not folded

over at intake during use.

Obstructions in vacuum tube

Unit stopped suddenly during vacu-

uming, and now starter won’t work

Object stuck in fan housing area

Unit jams repeatedly during use

Material being vacuumed too big or

too hard for blades to shred

Use vacuum for leaves and small

twigs, maximum 1/4” diameter x 3”

long.

Vacuum tube difcult to install or

remove from unit

Tube/housing t tight.

Apply small amount of soapy water

to end of tube to ease assembly or

removal. Turns tube 1/4 turn to loosen

for removal.

Remove vacuum tube and check fan

area. Remove object.

Check vacuum tube, and remove ob-

structions. Avoid wet leaves.

WARNING

Debris bag is ammable and could be ignited if allowed to contact

hot mufer cover or exhaust. Keep bag away from hot surfaces at

all times.

maInTenanCe InTervals

maInTenanCe

Your ECHO blower is designed to provide many hours of trouble free service. Regular scheduled maintenance will help

your blower achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take your

unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOURSELF or have

the ECHO Dealer do it, each maintenance task has been graded. If task is not listed, see your ECHO Dealer for repairs.

skIll level

Level 1 = Easy to do. Common tools may be required.

Level 2 = Moderate difculty. Some specialized tools may be required.

ECHO offers REPOWER

Maintenance Kits and Parts to make your maintenance job easier.

WARNING

Moving parts can amputate ngers or cause severe injuries. Keep hands, clothing and loose objects away from all

openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop

before removing obstructions, clearing debris, or servicing unit. Allow unit to cool before performing service. Wear

gloves to protect hands from sharp edges and hot surfaces.

COMPONENT / SYSTEM

MAINTENANCE

PROCEDURE

REQ'D

SKILL

LEVEL

DAILY OR

BEFORE USE

EVERY

REFUEL

3 MONTHS

OR 90

HOURS

YEARLY

600 HOURS

Air Filter Inspect/Clean

I / C * R *

Choke Shutter Inspect/Clean

I / C

Fuel Filter Inspect/Replace

I * I / R *

Fuel Cap Gasket Inspect/Replace

I * R *

Fuel System Inspect/Replace

I (1) * I (1) *

Spark Plug Inspect/Clean/Replace

I / C / R *

Cooling System Inspect/Clean

I / C

Muffler Spark Arrestor Inspect/Clean/Replace

I / C / R *

Cylinder Exhaust Port Inspect/Clean/Decarbon

I / C

Recoil Starter Rope Inspect/Clean

I / C *

Screws/Nuts/Bolts Inspect/Tighten/Replace

I *

MAINTENANCE PROCEDURE LETTER CODES:

I = INSPECT, R = REPLACE, C = CLEAN

IMPORTANT NOTE - Time intervals shown are maximum. Actual use and your experience will determine the

frequency of required maintenance.

MAINTENANCE PROCEDURE NOTES:

(1) Low evaporative fuel tanks DO NOT require regular maintenance to maintain emission integrity.

* All recommendations to replace are based on the finding of damage or wear during inspection.

Power Blower

Perator's Manual

aIr

fIlTer

Level 1.

Parts required: REPOWER

Air and Filter Kit

NOTE

Clean daily.

1. Close choke (Cold Start Position [ ]). This prevents dirt from

entering the carburetor throat when the air lter is removed. Brush

accumulated dirt from air cleaner area.

2. Remove air lter cover. Brush dirt from inside cover.

3. Remove air lter and lightly brush debris from lter. Replace

lter if it is damaged, fuel soaked, very dirty, or the rubber sealing

edges are deformed.

4. If lter can be reused, be certain it:

• Fits tightly in the air lter cavity.

• Is installed with the original side out.

5. Install air lter cover.

fuel fIlTer

Level 1.

Parts required: REPOWER

Air and Filter Kit

DANGER

Fuel is VERY ammable. Use extreme care when mixing, storing

or handling.

1. Use a clean rag to remove loose dirt from around fuel cap and

empty fuel tank.

2. Use the “fuel line hook” to pull the fuel line and lter from the

tank.

3. Remove the lter from the line and install the new lter.

CoolIng sysTem

Level 2.

Parts Required: None, if you are careful.

IMPORTANT

To maintain proper engine operating temperatures, cooling air must

pass freely through the cylinder n area. This ow of air carries

combustion heat away from the engine.

Overheating and engine seizure can occur when:

• Air intakes are blocked, preventing cooling air from reaching the

cylinder.

• Dust and grass build up on the outside of the cylinder. This build up

insulates the engine and prevents the heat from leaving.

Removal of cooling passage blockages or cleaning of cooling ns is

considered “Normal Maintenance”. Any failure attributed to lack of

maintenance is not warranted.

Cleaning Grill

1. Brush accumulated debris from crankcase intake grill above the

fuel tank.

0.65 mm

(0.026 in.)

spark plug

Level 2.

Parts Required: REPOWER

Tune-Up Kit

IMPORTANT

Use only NGK BPM-8Y spark plug (BPMR-8Y in Canada)

otherwise severe engine damage may occur.

1. Remove spark plug and check for fouling, worn and rounded

center electrode.

2. Clean the plug or replace with a new one. DO NOT sand blast to

clean. Remaining sand will damage engine.

3. Adjust spark plug gap by bending outer electrode.

4. Tighten spark plug to 150-170 kgf • cm (130-150 in • lbf).

Page is loading ...

Echo ES-250AA User manual

Brand: Echo

Model: ES-250AA

Category: Air blowers/dryers

Type: User manual

Download PDF

report

Echo ES-250AA User manual

Echo ES-250AA User manual

Related papers

Other documents