Page is loading ...
1-09-08
GREEN
BLACK
RED
WHITE
BLACK
RED
15
15
15
05.0410 Mounting
Bail
90.4524 Washer
(2)
90.4424 Bolt (2)
90.4972 Cover (1)
90.4072 Machine
Screw (4)
05.0502 SPDT
Switch (2)
90.3939 Red Pilot
Lamp (3)
90.3804 15 AMP
Fuse
02.6021 Circuit
Board Assembly
81.0198 #6 Blue
Spade Connnector (4)
81.0198 #6 Blue
Spade Connector (2)
41.0141.010Red (4')
41.0141.010Blk (4')
02.6020 Cable
Harness with
Connector (20')
90.3704 4-Way
Connector
90.6602 DUST COVER
90.4225 1/4-20 x
3 1/2" Slotted
Round Bolt (2)
90.4928 Split
Washer (2)
90.4150 1 /4-20
nylon insert ss (2)
90.4523 Stainless
Steel Washer (2)
90.4150 Stainless
Steel Nylon Insert
Nut (2)
90.4901 alum frame
MODEL NO. 02.6100
Sealed Beam
Installation and Maintenance
Instructions
90.3758 Lamp
Connector (10)
90.3057 Sealed
Beam Bulb (10)
90.6756 Rubber
Gasket (10)
34" Short Cable
PRODUCTS COMPANY 804 East Hwy 248 Cassville, MO 65625
U.S. and Canada Toll Free Numbers Phone: 800-641-4098 FAX: 800-526-1240
E-mail: [email protected]
WEB: www.able2products.com
SHO-ME
®
Installation Instructions
All connections are external. There is no need to open the control box during the installation process.
1. Remove dust cover by removing the two lock nuts and washers located on the back of the
arrow board.
2. Mount the
SHO-ME Directional Arrow Board on the vehicle as desired.
3. Replace dust cover.
4. Route the cable from the Arrow Board to the driver's compartment or wherever the control box
will be located.
5. A mounting bracket is provided for easy installation of the control box. Determine a suitable
position for the mounting bracket and attach it to the vehicle with appropriate fasteners.
6. Connect bare end of the heavy black wire to a suitable chassis ground.
7. Connect spade connector of heavy black wire to screw marked "NEG" on the terminal strip
located on the back of the controller.
8. Connect spade connector of white wire from the arrow board cable to screw marked "W" on
the terminal strip.
9. Connect spade connector of red wire from the arrow board cable to screw marked "R" on the
terminal strip.
10. Connect spade connector of black wire from the arrow board cable to screw marked "B" on the
terminal strip.
11. Connect spade connector of green wire from the arrow board cable to screw marked "G" on
the terminal strip.
12. Connect spade connector of heavy red wire to screw marked "POS" on the terminal strip
located on the back of the controller.
13. Connect bare end of the heavy red wire to a 12-volt positive power source.
Note: The above wiring connection instructions assume that the arrow board is mounted facing the rear
of the vehicle with the Arrow Board's mounting flange at the bottom position. If the arrow board is
installed facing the front of the vehicle or in a position with the flange up, the arrow board will not point in
the same direction as the pilot lights on the controller indicate. If the arrow board points right when the
controller indicates that it is pointing left and vice versa, the situation can be corrected by connecting the
white wire to the terminal marked "G" and the green wire to the terminal marked "W".
After completing the connections, check which direction the arrow board is flashing and be sure that it
coincides with the direction indicated by the control box.
Maintenance Instructions
Trouble Shooting
1. If arrow board is not operating or is not lighting to full brilliance, make sure all wire connections
are properly made and the power source is active. Take particular care in making certain that
ground connections are properly made.
2. If individual lamps in the arrow board are not operating properly, but the bulb is good, tighten
the lamp retaining screws since these screws complete the electrical connections.
R
Revised 5-07
Wiring for 02.6100 Arrow Board
Black
Green
Red
White
-
-
-
-
Ground
+12V Left
+12V Center
+12V Right
White to Red
Red to Red
Green to Red
Black to all
White/Gnd
G
R W B
-
+
SHO-ME
®
Made In U.S.A.
Black
Red
-
-
Ground
+12V
- 3 -
/
