Craig CCR9024 Owner's manual

FCC INFORMATION:

This equipment meets the limits for a class B digital device. Pursuant to Part 15 of

FCC rules. Only the cable supplied with the camcorder should be used. Operation

with other cables is likely to result in interference to radio and TV reception and

could void the user's authorization to operate this equipment. This device

complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions:

1) This device may not cause any harmful interference.

2) This device must accept any interference received, including interference that

may cause undesired operation. Modifications not authorized by the

manufacturer may void the user’s authority to operate this unit.

FCC NOTICE:

This equipment has been tested and found to comply with the limits for a class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates; uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment on and off, the user is

encouraged to try to correct the interference by one or more of the following

measures:

 Reorient or relocate the receiving antenna.

 Increase the distance between the equipment and receiver.

USER INFORMATION:

 Changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

 Never try to take pictures when operating a motor vehicle or while walking.

 Never try to open the case of the camcorder or attempt your own repairs.

Always leave service to authorized repair facilities.

 Physical damage and malfunction of this unit can cause the image data stored

in its memory to be deleted. Be sure to always keep backup copies of data by

transferring to a personal computer.

 In an environment with electrostatic discharge, the user may have to reset the

unit.

 Do not leave the camcorder in places subject to extremely high temperatures,

such as a sealed vehicle or in direct sunlight.

 Do not touch or press the display or lens.

Copyright Information:

stored in a retrieval system, or translated into any language in any form by any

means, optical, electronic, recording, or otherwise, without the written permission

of our company.

We reserve the right to revise this manual and to make changes to any or all parts

at any time, without obligation to notify any person or entity of such revisions and

changes.

Location of controls:

Mini USB Port: For recharge; files transmission; webcam.

Mini HDMI Port: To connect to Television.

Micro SD Card Slot: To insert external Micro SD Card for extension memory.

Reset Button: To restart the camera when the camera was halt; abnormal

operation.

/REC (Power On-Off/Record) Button:

 Press to power on the unit; press and hold until “OFF” appear on the

display then release the button to shut off the unit.

 In Video taking mode, press to start recording. Press again to stop.

 In photo taking mode, press to capture the photo.

MODE Button: Press repeatedly to change the capture modes.

MENU Button: Press repeatedly to enter to setting menu.

Preparation:

1. Battery Charging

The unit has a built-in rechargeable Li-polymer battery, recharge it before use as

below:

 Make sure the unit is in power off mode. (If the unit is in power on

mode, when connected to AC/USB Adaptor, it will turn to

Monitoring mode automatically).

 Turn the cover counterclockwise then take it off as the figure below:

 Connect the small plug from the supplied USB connection cable to the

Mini USB Port on the unit.

 Connect the other end to the USB Port on the supplied AC/USB

Adaptor.

 Plug the AC/USB Adaptor to any conveniently AC outlet having AC

100-240V~, 50/60 Hz.

IMPORTANT: This AC/DC Adaptor is intended to be correctly orientated in

a vertical or floor mount position.

Notes:

Your battery will last longer if you following these simple guidelines for charging

for and storing it.

A. For charging first time, charge it at least 10 hours.

B. Recharge and store the battery within the temperature range of 5°C~35°C

(40°F~95°F).

C. Do not over charge (longer than 24 hours). Excessive charging or discharging

may shorten the battery's life.

D. Battery life naturally shortens slowly over time.

E. The rechargeable battery incorporated in this product is not user replaceable.

2. Insert Micro SD card (Not included) into the SD Card slot:

 Turn the cover counterclockwise then take it off.

 Insert a Micro SD Memory card (up to 32G; Class 4, not included) into

the Micro SD Card Slot as the figure below before start use:

 To take out the card, press the card until “Click” sound is heard then

slide it out.

Notes:

 Before insert or replacing the Micro SD Card, make sure the unit has

been powered off.

 When inserting the Micro SD Card, make sure the direction you selected

is correct. Never insert violently to avoid damaging the card or the unit.

If it doesn’t work, please check if the direction is correct.

 When the card is used for the first time, or it has been used in other

device, it may need format through the Computer. Important:

Formatting the SD Card will delete all the files on the card. Upload

the files to your computer before formatting the card.

3. Time set:

 Press the /REC Button to power on the unit. The display will light.

 Press the MENU Button, current year will appear on the display and

blinking.

 Press the MODE or /REC Button repeatedly to set the year. After

setting, press the MENU Button, the current month will appear on the

display and blinking.

 Press the MODE or /REC Button repeatedly to set the month. After

setting, press the MENU Button, the current date will appear on the

display and blinking.

 Press the MODE or /REC Button repeatedly to set the date. After

setting, press the MENU Button, the current hour will appear on the

display and blinking.

 Press the MODE or /REC Button repeatedly to set the hour. After

setting, press the MENU Button, the current minute will appear on the

display and blinking.

 Press the MODE or /REC Button repeatedly to set the minute. After

setting, press the MENU Button, “FOR” will appear on the display.

Press the MENU Button again to save the setting and exit.

4. Mountings:

 Mounting the camera on the top of the bicycle helmet with the supplied

assembly’s kit as the figures below:

Pic 1 Pic 2 Pic 3

Pic 4 Pic 5 Pic 6

 Mounting the camera on the helmet side with the supplied assembly’s

kit as the figures below:

Pic 1 Pic 2 Pic 3

Pic 4 Pic 5 Pic 6

Pic 7 Pic 8

 Mount the camera on the handle of bicycle/motorcycle with the supplied

assembly’s kit as the figures below:

Pic 1 Pic 2 Pic 3

Pic 4

OPERATION

Video/Photo Capture:

1. Press the /REC Button to power on the unit, the display will light.

2. Press the MODE Button repeatedly to set or reset the capture mode to 720

(takes video in 1280 x 720 pixels, HD); 1080 (take videos in 1920 x 1080

pixels, Full HD) or XXXX (photo capture mode; XXXX = Total number of

photo can take).

3. Face the lens to the objet you want capture.

4. In video capture mode, press the /REC Button to start recording. When

finished, press the /REC Button to stop. Or,

In photo capture mode, press the /REC Button once to capture the photo.

5. When finished, press and hold the /REC Button until “OFF” appear on the

display then release the button to shut off the unit.

Monitoring:

1. Press the /REC Button to power on the unit, the display will light.

2. Press the MODE Button repeatedly to enter to video capture mode (720 or

1080 appear on the display).

3. Connected the unit to the supplied AC/USB Adaptors. The unit will enter to

monitoring mode that takes the videos. Red and yellow back light on the

display will light and red will blink.

Notes:

 For saving memories, the unit will takes the video in 1280 x 720 pixels

in 10 fps (frame per second) only.

 When the memory is full, the new videos will cover the beginning’s

video automatically.

4. To stop, press and hold the /REC Button until “OFF” appear on the

display then release the button.

Watching/Saving the Videos/Photos:

1. Press the /REC Button to power on the unit, the display will light.

2. Connected the unit to any Computer using follows operation system. “PC”

will appear on the display.

 Windows 8

 Windows 7

 Windows Vista

 Windows XP

3. Upload and saving the video/photo files from the unit to Computer.

4. Using the preloaded Video/Photo Player in your Computer Such like Window

Media Player to watch/read the videos and photos.

Web Camera:

The unit can use as a web-camera as below:

1. Press the /REC Button to power on the unit, the display will light.

2. Connected the unit to any Computer using follows operation system. “PC”

will appear on the display.

 Windows 8

 Windows 7

 Windows Vista

 Windows XP

3. Press the MODE Button; “PC” on the display will become to “PCC”.

4. In most of Computer, it will auto installed the driver to hook up the unit.

Then, operation the unit as the on screen instructions on the Computer. If

your computer have not installed correct divers, pre-install the supplied

webcam driver to your computer before connected the unit as:

 Insert the supplied disc to the CD/DVD Driver in your computer.

 Wait a few seconds, the small window of the disc will appear on the

computer’s screen.

 Double click “Open the folder to view the file”, the follows icons

will appear on the screen.

 Click and Drag the icon of to your desktop.Uninstall the disc

from your computer.

 Connected the unit to the computer and enter the PCC mode as previous

procedures, double click the icon of on your computer’s

desktop to open and enter to webcam mode.

 Monitoring and/or record the videos as the on screen instruction as

desire.

Waterproof:

The unit can use under water 16 feet (5M). Before use in water, please make sure

the cover already tightly closed.

Specifications and System Requirements

Product specifications:

Sensor: 1.3 Mega pixel CMOS

Capture mode: Video: 1280 x 720 pixels, 30 fps or 1920 x 1080 pixels, 25fps

Photo: 5M (2592 x 1944)

Lens: f = 2.8mm, F = 2.4

Focus range: 1.2m (4 feet) ~ infinity

Storage media: SD card (Up to 32GB, class 4; not included)

File format: JPG/AVI

Power Source: Built-in Rechargeable Li-poly Battery:

Recharge by DV

5V Through Mini USB Port

I/O Port: Mini USB2.0/Mini HDMI/Micro SD Card Slot

Computer system Requirements:

Operation System Microsoft Windows XP, Vista, 7, 8

CPU Above Intel PIII667 or CPU of equal performance

Memory Above 128 MB

Sound card and display

Support Direct X8 or above

CD-ROM 4X speed or above

Hard Disk 500 MB space above useable

Other USB 2.0 port

Accessories:

1 x User’s manual

1 x USB connection cable

1 x Helmet grip

1 x Universal bracket

1 x Bicycle bracket

2 x Rubber pads

1 x Elastic strap

1 x Velcro strap

1 x AC/USB Adaptor (Input: AC 100-240V~50/60Hz; Output: DC

5V 1000mA)

1 x Software CD (Suitable for: Windows 8; Windows 7; Windows Vist; Windows

XP)

SPECIFICATIONS ARE SUBJECT TO CHANGE

WITHOUT NOTICE

Craig CCR9024 Owner's manual

Craig CCR9024 Owner's manual

Related papers

Other documents