Seagate ST2000NM0033 Constellation® ES.3 SATA 6Gb/s 2-TB Hard Drive User manual

Brand: Seagate

Model: ST2000NM0033 Constellation® ES.3 SATA 6Gb/s 2-TB Hard Drive

Category: Internal hard drives

Type: User manual

This manual is also suitable for

Standard models

ST4000NM0033

ST3000NM0033

ST2000NM0033

ST1000NM0033

Self-Encrypting Drive models

ST4000NM0053

ST3000NM0053

ST2000NM0053

ST1000NM0053

SED (FIPS 140-2) models

ST4000NM0073

ST3000NM0073

ST2000NM0073

ST1000NM0073

Constellation ES.3

SATA Product Manual

100671511, Rev. F

March 2016

Publication number: 100671511, Rev. F March 2016

Seagate, Seagate Technology and the Spiral logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. Raid Rebuild and SeaTools are either

trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/or other countries. The FIPS logo is a certification mark of NIST,

which does not imply product endorsement by NIST, the U.S., or Canadian governments.All other trademarks or registered trademarks are the property of their respective owners.

No part of this publication may be reproduced in any form without written permission of Seagate Technology LLC.

Call 877-PUB-TEK1 (877-782-8351) to request permission.

When referring to drive capacity, one gigabyte, or GB, equals one billion bytes and one terabyte, or TB, equals one trillion bytes. Your computer’s operating system may use a different

standard of measurement and report a lower capacity. In addition, some of the listed capacity is used for formatting and other functions, and thus will not be available for data storage.

Actual quantities will vary based on various factors, including file size, file format, features and application software. Actual data rates may vary depending on operating environment

and other factors. The export or re-export of hardware or software containing encryption may be regulated by the U.S. Department of Commerce, Bureau of Industry and Security (for

more information, visit www.bis.doc.gov), and controlled for import and use outside of the U.S. Seagate reserves the right to change, without notice, product offerings or specifications.

Document Revision History

Revision Date Description of changes

Rev. A 10/05/2012 Initial release.

Rev. B 01/14/2014 5 & 7.

Rev. C 02/13/2014 fc, 2, 4 & 37.

Rev. D 04/01/2014 4, 19 & 35.

Rev. E 10/16/2014 7 & 22.

Rev. F 03/28/2016 6-7, 9-12, 22, 25 & 27.

Constellation ES.3 Serial ATA Product Manual, Rev. F 2

Contents

Seagate® Technology Support Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.1 About the Serial ATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.1 Specification summary tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.2 Formatted capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.2.1 LBA mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.3 Default logical geometry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.4 Recording and interface technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.5 Start/stop times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.6 Power specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.6.1 Power consumption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.6.2 Conducted noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

2.6.3 Voltage tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

2.6.4 Power-management modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

2.7 Environmental limits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

2.7.1 Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

2.7.2 Humidity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

2.7.3 Altitude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

2.7.4 Shock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

2.7.5 Vibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

2.8 Acoustics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

2.9 Test for Prominent Discrete Tones (PDTs). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

2.10 Electromagnetic immunity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

2.11 Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

2.11.1 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF) . . . . . . . . . . . . . 22

2.12 Agency certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

2.12.1 Safety certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

2.12.2 Electromagnetic compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

2.12.3 FCC verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

2.13 Environmental protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

2.13.1 European Union Restriction of Hazardous Substances (RoHS) Directive. . . . . . . . . . . . . . 24

2.13.2 China Restriction of Hazardous Substances (RoHS) Directive . . . . . . . . . . . . . . . . . . . . . . . 24

2.14 Corrosive environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

2.15 Reference documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

2.16 Product warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

3.0 Configuring and mounting the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

3.1 Handling and static-discharge precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

3.2 Configuring the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

3.3 Serial ATA cables and connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

3.4 Drive mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

3.4.1 Mechanical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

4.0 About FIPS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

5.0 About self-encrypting drives. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

5.1 Data encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

5.2 Controlled access. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

5.2.1 Admin SP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

5.2.2 Locking SP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

5.2.3 Default password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Constellation ES.3 Serial ATA Product Manual, Rev. F 3

Contents

5.3 Random number generator (RNG). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

5.4 Drive locking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

5.5 Data bands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

5.6 Cryptographic erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

5.7 Authenticated firmware download . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

5.8 Power requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

5.9 Supported commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

5.10 RevertSP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

5.11 ATA Security Erase Unit Command on SED SATA drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

5.12 Sanitize Device - CRYPTO SCRAMBLE EXT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

6.0 Serial ATA (SATA) interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

6.1 Hot-Plug compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

6.2 Serial ATA device plug connector pin definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

6.3 Supported ATA commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

6.3.1 Identify Device command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

6.3.2 Set Features command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

6.3.3 S.M.A.R.T. commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Constellation ES.3 Serial ATA Product Manual, Rev. F 4

For information regarding online support and services, visit: http://www.seagate.com/contacts/

For information regarding Warranty Support, visit: http://www.seagate.com/support/warranty-and-replacements/

For information regarding data recovery services, visit: http://www.seagate.com/services-software/seagate-recovery-

services/recover/

For Seagate OEM, Distribution partner and reseller portals, visit: http://www.seagate.com/partners

Seagate® Technology Support Services

Constellation ES.3 Serial ATA Product Manual, Rev. F 5

1.0 Introduction

This manual describes the functional, mechanical and interface specifications for the following:

Seagate

Constellation

ES.3 Serial ATA model drives:.

These drives provide the following key features:

• 7200 RPM spindle speed.

• Full-track multiple-sector transfer capability without local processor intervention.

• High instantaneous (burst) data-transfer rates (up to 600MB per second).

• Native Command Queuing with command ordering to increase performance in demanding applications.

• Perpendicular recording technology provides the drives with increased areal density.

• PowerChoice™ for selectable power savings

• SeaTools™ diagnostic software performs a drive self-test that eliminates unnecessary drive returns.

• State-of-the-art cache and on-the-fly error-correction algorithms.

• Support for S.M.A.R.T. drive monitoring and reporting.

• Supports latching SATA cables and connectors.

• Top Cover Attached motor for excellent vibration tolerance

• Worldwide Name (WWN) capability uniquely identifies the drive.

For more information on FIPS 140-2 Level 2 certification see See Section 4.0 on page 28 .

1.1 About the Serial ATA interface

The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary advantages include:

• Easy installation and configuration with true plug-and-play connectivity. It is not necessary to set any jumpers or other configura-

tion options.

• Thinner and more flexible cabling for improved enclosure airflow and ease of installation.

• Scalability to higher performance levels.

In addition, Serial ATA makes the transition from parallel ATA easy by providing legacy software support. Serial ATA was designed to

allow the user to install a Serial ATA host adapter and Serial ATA disk drive in current system and expect all existing applications to

work as normal.

The Serial ATA interface connects each disk drive in a point-to-point configuration with the Serial ATA host adapter. There is no

master/slave relationship with Serial ATA devices like there is with parallel ATA. If two drives are attached on one Serial ATA host

adapter, the host operating system views the two devices as if they were both “masters” on two separate ports. This essentially

means both drives behave as if they are Device 0 (master) devices.

The Serial ATA host adapter and drive share the function of emulating parallel ATA device behavior to provide backward

compatibility with existing host systems and software. The Command and Control Block registers, PIO and DMA data transfers, resets,

and interrupts are all emulated.

The Serial ATA host adapter contains a set of registers that shadow the contents of the traditional device registers, referred to as the

Shadow Register Block. All Serial ATA devices behave like Device 0 devices. For additional information about how Serial ATA emulates

parallel ATA, refer to the “Serial ATA: High Speed Serialized AT Attachment” specification. The specification can be downloaded from

www.serialata.or

Standard models

Self-Encrypting Drive (SED) SED FIPS 140-2 Drive

ST4000NM0033 ST4000NM0053 ST4000NM0073

ST3000NM0033 ST3000NM0053 ST3000NM0073

ST2000NM0033 ST2000NM0053 ST2000NM0073

ST1000NM0033 ST1000NM0053 ST1000NM0073

Note

Seagate recommends validating the drive configuration with the selected HBA/RAID

controller manufacturer to ensure full 4 & 3TB capacity capabilities.

Note

The host adapter may, optionally, emulate a master/slave environment to host software where two devices on

separate Serial ATA ports are represented to host software as a Device 0 (master) and Device 1 (slave) accessed at the

same set of host bus addresses. A host adapter that emulates a master/slave environment manages two sets of

shadow registers. This is not a typical Serial ATA environment.

Constellation ES.3 Serial ATA Product Manual, Rev. F 6

2.0 Drive specifications

Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the

phrases the drive and this drive are used throughout this manual to indicate the following drive models:

2.1 Specification summary tables

The specifications listed in the following tables are for quick reference. For details on specification measurement or definition, see the

appropriate section of this manual.

Table 1 Drive specifications summary

Standard models

Self-Encrypting Drive (SED) SED FIPS 140-2 Drive

ST4000NM0033 ST4000NM0053 ST4000NM0073

ST3000NM0033 ST3000NM0053 ST3000NM0073

ST2000NM0033 ST2000NM0053 ST2000NM0073

ST1000NM0033 ST1000NM0053 ST1000NM0073

Drive specification

ST4000NM0033

ST4000NM0053

ST4000NM0073

ST3000NM0033

ST3000NM0053

ST3000NM0073

ST2000NM0033

ST2000NM0053

ST2000NM0073

ST1000NM0033

ST1000NM0053

ST1000NM0073

Formatted (512 bytes/sector)* 4TB 3TB 2TB 1TB

Guaranteed sectors 7,814.037,168 5,860,533,168 3,907,029,168 1,953,525,168

Heads 10 8 5 3

Discs 5 4 3 2

Bytes per sector 512

Default sectors per track 63

Default read/write heads 16

Default cylinders 16,383

Recording density, KBPI (Kb/in max) 1862

Track density, KTPI (ktracks/in avg.) 305

Areal density, (Gb/in

avg) 566

Spindle speed (RPM) 7200

Internal data transfer rate (Mb/s max) 2160

Sustained data transfer rate OD

(MB/s max)

175

I/O data-transfer rate (MB/s max) 600

ATA data-transfer modes supported

PIO modes 0–4

Multiword DMA modes 0–2

Ultra DMA modes 0–6

Cache buffer 128MB (129,536KB)

Weight: (maximum) 700g (1.543 lb) 655g (1.444 lb) 635g (1.400 lb) 605g (1.334 lb)

Average latency 4.16ms

Power-on to ready (sec) 20 (max)

Standby to ready (sec) 20 (max)

Startup current (typical) 12V (peak)

2.6A

2.0A (optional configuration through Smart Command Transport)

Voltage tolerance (including noise)

5V ±5%

12V ±5%

Drive case temperature

5° to 60°C (operating/tested)

–40° to 70°C (nonoperating)

Temperature gradient

(°C per hour max)

20°C (operating)

30°C (nonoperating)

Relative humidity

5% to 90% (operating)

5% to 95% (nonoperating)

Relative humidity gradient 30% per hour max

Constellation ES.3 Serial ATA Product Manual, Rev. F 7

*One GB equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting.

**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels.

2.2 Formatted capacity

*One GB equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating

environment and formatting.

2.2.1 LBA mode

When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of

guaranteed sectors as defined above.

See Section 6.3.1, "Identify Device command" (words 60-61 and 100-103) for additional information about 48-bit addressing support

of drives with capacities over 137GB.

2.3 Default logical geometry

Altitude, operating

–304.8 m to 3,048 m

(–1000 ft to 10,000+ ft)

Altitude, nonoperating

(below mean sea level, max)

–304.8 m to 12,192 m

(–1000 ft to 40,000+ ft)

Operational Shock (max at 2 ms) Read 70 Gs / Write 40 Gs

Non-Operational Shock (max at 2 ms) 300 Gs

Vibration, operating

5–22 Hz: 0.25 Gs, Limited displacement

22–350 Hz: 0.50 Gs

350–500 Hz: 0.25 Gs

Operation Rotational vibration 20–1500Hz: 12.5 rads/s²

Vibration, nonoperating 10–500 Hz: 4.9 Grms ref

Drive acoustics, sound power (bels)

Idle**

2.8 (typical)

3.0 (max)

Performance seek

3.0 (typical)

3.4 (max)

Nonrecoverable read errors 1 sector per 10

bits read

Annualized Failure Rate (AFR) 0.44% based on 8760 POH

Maximum Rated Workload

Maximum rate of <550TB/year

Workloads exceeding the annualized rate may degrade the drive MTBF and impact product reliability. The Annualized

Workload Rate is in units of TB per year, or TB per 8760 power on hours. Workload Rate = TB transferred * (8760 /

recorded power on hours).

Warranty

To determine the warranty for a specific drive, use a web browser to access the following web page:

http://www.seagate.com/support/warranty-and-replacements/.

From this page, click on the “Is my Drive under Warranty” link. The following are required to be provided: the drive

serial number, model number (or part number) and country of purchase. The system will display the warranty infor-

mation for the drive.

Load-unload cycles 600,000

Supports Hotplug operation per

Serial ATA Revision 3.2 specification

Yes

Formatted capacity* Guaranteed sectors Bytes per sector

4TB 7,814.037,168

512

3TB 5,860,533,168

2TB 3,907,029,168

1TB 1,953,525,168

Cylinders Read/write heads Sectors per track

16,383 16 63

Drive specification

ST4000NM0033

ST4000NM0053

ST4000NM0073

ST3000NM0033

ST3000NM0053

ST3000NM0073

ST2000NM0033

ST2000NM0053

ST2000NM0073

ST1000NM0033

ST1000NM0053

ST1000NM0073

Constellation ES.3 Serial ATA Product Manual, Rev. F 8

LBA mode

When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of

guaranteed sectors as defined above.

2.4 Recording and interface technology

2.5 Start/stop times

2.6 Power specifications

The drive receives DC power (+5V or +12V) through a native SATA power connector. See Figure 10 on page 26.

2.6.1 Power consumption

Power requirements for the drives are listed in the table on page 9. Typical power measurements are based on an average of drives

tested, under nominal conditions, using 5.0V and 12.0V input voltage at 25°C ambient temperature.

• Spinup power

Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating speed.

• Seek mode

During seek mode, the read/write actuator arm moves toward a specific position on the disk surface and does not execute a read

or write operation. Servo electronics are active. Seek mode power represents the worst-case power consumption, using only ran-

dom seeks with read or write latency time. This mode is not typical and is provided for worst-case information.

• Read/write power and current

Read/write power is measured with the heads on track, based on a 16-sector write followed by a 32-ms delay, then a 16-sector

read followed by a 32ms delay.

• Operating power and current

Operating power is measured using 40 percent random seeks, 40 percent read/write mode (1 write for each 10 reads) and 20 per-

cent drive idle mode.

• Idle mode power

Idle mode power is measured with the drive up to speed, with servo electronics active and with the heads in a random track loca-

tion.

•Standby mode

During Standby mode, the drive accepts commands, but the drive is not spinning, and the servo and read/write electronics are in

power-down mode.

Interface Serial ATA (SATA)

Recording method Perpendicular

Recording density, KBPI (Kb/in max) 1862

Track density, KTPI (ktracks/in avg) 305

Areal density (Gb/in

avg) 566

Spindle speed (RPM) (± 0.2%) 7200

Internal data transfer rate (Mb/s max) 2160

Sustained data transfer rate (MB/s max) 175

I/O data-transfer rate (MB/s max) 600 (Ultra DMA mode 5)

4TB models 3TB models 2TB models 1TB models

Power-on to Ready (sec) 20 (max)

Standby to Ready (sec) 20 (max)

Ready to spindle stop (sec) 20 (max)

Constellation ES.3 Serial ATA Product Manual, Rev. F 9

*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic

and power to operational levels.

Table 2 4TB Drive DC power requirements

Notes 6.0Gb mode

Voltage +5V +12V

Regulation ± 5%

Avg Idle Current * 0.28 0.50

Advanced Idle Current *

Idle_A 0.17 0.49

Idle_B 0.16 0.45

Idle_C 0.15 0.27

Standby 0.15 0.01

Maximum Start Current

DC (peak DC) 3s 0.52 2.16

AC (Peak DC) 3s 0.85 2.89

Delayed Motor Start (DC max) 3s 0.16 0.01

Operating current (random read):

Typical DC 0.31 0.81

Maximum DC 3s 0.32 0.84

Maximum DC (peak) 3s 1.83 2.43

Operating current (random write)

Typical DC 0.30 0.78

Maximum DC 3s 0.32 0.79

Maximum DC (peak) 3s 0.78 2.39

Operating current (sequential read)

Typical DC 0.63 0.56

Maximum DC 3s 0.66 0.57

Maximum DC (peak) 3s 1.36 2.20

Operating current (sequential write)

Typical DC 0.55 0.60

Maximum DC 3s 0.57 0.61

Maximum DC (peak) 3s 1.40 2.18

Constellation ES.3 Serial ATA Product Manual, Rev. F 10

*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic

and power to operational levels.

Table 3 3TB Drive DC power requirements

Notes 6.0Gb mode

Voltage +5V +12V

Regulation ± 5%

Avg Idle Current * 0.28 0.50

Advanced Idle Current *

Idle_A 0.17 0.49

Idle_B 0.16 0.45

Idle_C 0.15 0.27

Standby 0.15 0.01

Maximum Start Current

DC (peak DC) 3s 0.52 2.16

AC (Peak DC) 3s 0.85 2.89

Delayed Motor Start (DC max) 3s 0.16 0.01

Operating current (random read):

Typical DC 0.31 0.81

Maximum DC 3s 0.32 0.84

Maximum DC (peak) 3s 1.83 2.43

Operating current (random write)

Typical DC 0.30 0.78

Maximum DC 3s 0.32 0.79

Maximum DC (peak) 3s 0.78 2.39

Operating current (sequential read)

Typical DC 0.63 0.56

Maximum DC 3s 0.66 0.57

Maximum DC (peak) 3s 1.36 2.20

Operating current (sequential write)

Typical DC 0.55 0.60

Maximum DC 3s 0.57 0.61

Maximum DC (peak) 3s 1.40 2.18

Constellation ES.3 Serial ATA Product Manual, Rev. F 11

*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic

and power to operational levels.

Table 4 2TB Drive DC power requirements

Notes 6.0Gb mode

Voltage +5V +12V

Regulation ± 5%

Avg Idle Current * 0.28 0.36

Advanced Idle Current *

Idle_A 0.17 0.36

Idle_B 0.16 0.32

Idle_C 0.15 0.21

Standby 0.15 0.01

Maximum Start Current

DC (peak DC) 3s 0.48 2.86

AC (Peak DC) 3s 0.67 2.91

Delayed Motor Start (DC max) 3s 0.16 0.01

Operating current (random read):

Typical DC 0.30 0.66

Maximum DC 3s 0.31 0.71

Maximum DC (peak) 3s 1.40 2.27

Operating current (random write)

Typical DC 0.30 0.63

Maximum DC 3s 0.31 0.64

Maximum DC (peak) 3s 0.67 2.24

Operating current (sequential read)

Typical DC 0.59 0.40

Maximum DC 3s 0.60 0.41

Maximum DC (peak) 3s 1.24 1.98

Operating current (sequential write)

Typical DC 0.49 0.43

Maximum DC 3s 0.50 0.44

Maximum DC (peak) 3s 0.80 1.87

Constellation ES.3 Serial ATA Product Manual, Rev. F 12

*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic

and power to operational levels.

Table 5 1TB Drive DC power requirements

Notes 6.0Gb mode

Voltage +5V +12V

Regulation ± 5%

Avg Idle Current * 0.30 0.53

Advanced Idle Current *

Idle_A 0.17 0.30

Idle_B 0.16 0.27

Idle_C 0.16 0.18

Standby 0.15 0.01

Maximum Start Current

DC (peak DC) 3s 0.60 2.12

AC (Peak DC) 3s 1.57 2.89

Delayed Motor Start (DC max) 3s 0.16 0.01

Operating current (random read):

Typical DC 0.32 0.54

Maximum DC 3s 0.34 0.57

Maximum DC (peak) 3s 1.23 2.10

Operating current (random write)

Typical DC 0.32 0.55

Maximum DC 3s 0.33 0.56

Maximum DC (peak) 3s 0.69 2.08

Operating current (sequential read)

Typical DC 0.63 0.33

Maximum DC 3s 0.67 0.34

Maximum DC (peak) 3s 0.92 1.90

Operating current (sequential write)

Typical DC 0.56 0.38

Maximum DC 3s 0.58 0.38

Maximum DC (peak) 3s 0.92 1.70

Constellation ES.3 Serial ATA Product Manual, Rev. F 13

2.6.1.1 Typical current profiles

Figure 1. 4TB Typical 5V startup and operation current profile

Figure 2. 4TB Typical 12V startup and operation current profile

Constellation ES.3 Serial ATA Product Manual, Rev. F 14

2.6.1.2 Typical current profiles

Figure 3. 3TB Typical 5V startup and operation current profile

Figure 4. 3TB Typical 12V startup and operation current profile

Constellation ES.3 Serial ATA Product Manual, Rev. F 15

2.6.1.3 Typical current profiles

Figure 5. 2TB Typical 5V startup and operation current profile

Figure 6. 2TB Typical 12V startup and operation current profile

Constellation ES.3 Serial ATA Product Manual, Rev. F 16

2.6.1.4 Typical current profiles

Figure 7. 1TB Typical 5V startup and operation current profile

Figure 8. 1TB Typical 12V startup and operation current profile

Constellation ES.3 Serial ATA Product Manual, Rev. F 17

2.6.2 Conducted noise

Input noise ripple is measured at the host system power supply across an equivalent 80-ohm resistive load on the +12 V line or an

equivalent 15-ohm resistive load on the +5V line.

• Using 12V power, the drive is expected to operate with a maximum of 120mV peak-to-peak square-wave injected noise at up to

10MHz.

• Using 5V power, the drive is expected to operate with a maximum of 100mV peak-to-peak square-wave injected noise at up to

10MHz.

2.6.3 Voltage tolerance

Voltage tolerance (including noise):

5V ± 5%

12V ± 5%

2.6.4 Power-management modes

The drive provides programmable power management to provide greater energy efficiency. In most systems, the user can control

power management through the system setup program. The drive features the following power-management modes:

• Active mode

The drive is in Active mode during the read/write and seek operations.

• Idle mode

The buffer remains enabled, and the drive accepts all commands and returns to Active mode any time disk access is necessary.

• Standby mode

The drive enters Standby mode when the host sends a Standby Immediate command. If the host has set the standby timer, the

drive can also enter Standby mode automatically after the drive has been inactive for a specifiable length of time. The standby

timer delay is established using a Standby or Idle command. In Standby mode, the drive buffer is enabled, the heads are parked

and the spindle is at rest. The drive accepts all commands and returns to Active mode any time disk access is necessary.

• Sleep mode

The drive enters Sleep mode after receiving a Sleep command from the host. In Sleep mode, the drive buffer is disabled, the

heads are parked and the spindle is at rest. The drive leaves Sleep mode after it receives a Hard Reset or Soft Reset from the host.

After receiving a reset, the drive exits Sleep mode and enters Standby mode with all current translation parameters intact.

• Idle and Standby timers

Each time the drive performs an Active function (read, write or seek), the standby timer is reinitialized and begins counting down

from its specified delay times to zero. If the standby timer reaches zero before any drive activity is required, the drive makes a

transition to Standby mode. In both Idle and Standby mode, the drive accepts all commands and returns to Active mode when

disk access is necessary.

Note

Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write current.

Power modes Heads Spindle Buffer

Active Tracking Rotating Enabled

Idle_a ID Biased Rotating Enabled

Idle_b Parked Rotating Enabled

Idle_c Parked Rotating at lower RPM Enabled

Standby Parked Stopped Enabled

Sleep Parked Stopped Disabled

Constellation ES.3 Serial ATA Product Manual, Rev. F 18

2.6.4.1 Extended Power Conditions - PowerChoice

Utilizing the load/unload architecture a programmable power management interface is provided to tailor systems for reduced

power consumption and performance requirements.

The table below lists the supported power conditions available in PowerChoice. Power conditions are ordered from highest power

consumption (and shortest recovery time) to lowest power consumption (and longest recovery time) as follows: Idle_a power >=

Idle_b power >= Idle_c power >= Standby_z power. The further down in the table, the more power savings is actualized. For

example, Idle_b results in greater power savings than the Idle_a power condition. Standby results in the greatest power savings.

Each power condition has a set of current, saved and default settings. Default settings are not modifiable. Default and saved settings

persist across power-on resets. The current settings do not persist across power-on resets. At the time of manufacture, the default,

saved and current settings are in the Power Conditions log match.

PowerChoice is invoked using one of two methods

• Automatic power transitions which are triggered by expiration of individual power condition timers. These timer values may be

customized and enabled using the Extended Power Conditions (EPC) feature set using the standardized Set Features command

interface.

• Immediate host commanded power transitions may be initiated using an EPC Set Features "Go to Power Condition" subcommand

to enter any supported power condition. Legacy power commands Standby Immediate and Idle Immediate also provide a

method to directly transition the drive into supported power conditions.

PowerChoice exits power saving states under the following conditions

• Any command which requires the drive to enter the PM0: Active state (media access)

•Power on reset

PowerChoice provides the following reporting methods for tracking purposes

Check Power Mode Command

• Reports the current power state of the drive

Identify Device Command

• EPC Feature set supported flag

• EPC Feature enabled flag is set if at least one Idle power condition timer is enabled

Power Condition Log reports the following for each power condition

• Nominal recovery time from the power condition to active

• If the power condition is Supported, Changeable, and Savable

• Default enabled state, and timer value

• Saved enabled state, and timer value

• Current enabled state, and timer value

S.M.A.R.T. Read Data Reports

• Attribute 192 - Emergency Retract Count

• Attribute 193 - Load/Unload Cycle Count

Power Condition Name Power Condition ID Description

Idle_a 81

Reduced electronics

Idle_b 82

Heads unloaded. Disks spinning at full RPM

Idle_c 83

Heads unloaded. Disks spinning at reduced RPM

Standby_z 00

Heads unloaded. Motor stopped (disks not spinning)

Constellation ES.3 Serial ATA Product Manual, Rev. F 19

PowerChoice Manufacture Default Power Condition Timer Values

Default power condition timer values have been established to assure product reliability and data integrity. A minimum timer value

threshold of two minutes ensures the appropriate amount of background drive maintenance activities occur. Attempting to set a

timer values less than the specified minimum timer value threshold will result in an aborted EPC "Set Power Condition Timer"

subcommand.

Setting power condition timer values less than the manufacturer specified defaults or issuing the EPC "Go to Power Condition"

subcommand at a rate exceeding the default timers may limit this products reliability and data integrity.

PowerChoice Supported Extended Power Condition Feature Subcommands

PowerChoice Supported Extended Power Condition Identifiers

Power Condition Name Manufacturer Default Timer Values

Idle_a 2 min

Idle_b 4 min

Idle_c 10 min

Standby_z 15 min

EPC Subcommand Description

Restore Power Condition Settings

Go to Power Condition

Set Power Condition Timer

Set Power Condition State

Power Condition Identifiers Power Condition Name

Standby_z

01 - 80

Reserved

Idle_a

Idle_b

Idle_c

84 - FE

Reserved

All EPC Power Conditions

Page is loading ...

Seagate ST2000NM0033 Constellation® ES.3 SATA 6Gb/s 2-TB Hard Drive User manual

Brand: Seagate

Model: ST2000NM0033 Constellation® ES.3 SATA 6Gb/s 2-TB Hard Drive

Category: Internal hard drives

Type: User manual

This manual is also suitable for

Download PDF

report

Seagate ST2000NM0033 Constellation® ES.3 SATA 6Gb/s 2-TB Hard Drive User manual

This manual is also suitable for

Seagate ST2000NM0033 Constellation® ES.3 SATA 6Gb/s 2-TB Hard Drive User manual

Related papers

Other documents