Kenmore 41727182702 Installation guide

Brand: Kenmore

Model: 41727182702

Type: Installation guide

This manual is also suitable for

41727182704

Coin- Operated Commercial

Tumble Action Washer

PIN 134778300 (0706) Sears, Roebuck and Co., Hoffman Estates, {L 60179 U.S.A. www.sears.com

TABLE OF CONTENTS

Important Safety Instructions .......................................... 3

Prednstallation Requirements ....................................... 4

Electrical Requirements ................................................. 4

Grounding Requirements .............................................. 4

Water Supply Requirements .......................................... 4

Drain Requirements ........................................................ 4

Location Of You rWasher. .............................................. 4

Rough-In Dimensions .................................................... 5

Unpacking ....................................................................... 6

Installation .................................................................. 6-7

Coin slide installation ................................................ 7-9

Meter case instructions ................................................. 9

Replacement Parts.......................................................... 10

Partslists.................................................................... 10-11

Warranty. ........................................................................ 12

Before beginning installation, carefully read

these instructions. This will simplify the

installation and ensure the washer is

installed correctly and safely. Leave these

instructions near the washer after

installation for future reference.

NOTE: The electrical service to the washer

must conform with local codes and

ordinances and the latest edition of the

National Electrical Code, ANSI/NFPA 70.

Pyod , ct, £e:s<ot

For Searswarranty information or to contact a SearsService Center,

call 1-800-4-my-HOME (1-800-469-4663)

If you need SERVICE or PARTS for your Kenmore

coin-operated washer: be ready to give the model number, serial

number and date of purchase. Record below.

Model number

Serial number

NOTE: The instructions appearing in this

INSTALLATION AND SAFETY INSTRUCTIONS

manual are not meant to cover every possible

condition and situation that may occur. Common

sense and caution must be practiced when

Purchase date

Record Coin Box

Key Number

installing, operating and maintaining any

appliance. Key number is on key and/or coin box.

WASHER SAFETY

Your safety and the safety of others is very important. We have provided many important safety messages in the Installation

Instructions/Use & Care Guide and on your appliance. Always read and obey all safety messages.

_rhis isthe safety alert symbol. This symbol alerts you to hazards that can kill or hurt you or others. All safety messageswill be

preceded by the safety aler_symbol and the word "DANGER" or "WARNING". These words mean:

You can be killed or seriously injured if you don't immediately follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will identify the hazard, tell you how to reduce the ct_ance of injury, and tell you what can happen if the

instructions are not followed.

Foryour safety the information in this manual must be followed to minimize the risk of fire or explosion or to prevent

property damage, personal injury or lossof life.

- Do not store or usegasoline or other flammable vapors and liquid in the vicinity of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Clear the room, building or area of all occupants.

• Immediately call your gas supplier from a neighbor's phone. Follow the gas suppliers instructions.

• If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency or the gas supplier.

Your washer isequipped with a door safety interlock. Verify proper operation of interlock system daily, using the following procedure:

1.With the washer door open, insert the required number of coins and pressthe STARTbutton. THE WASHERMUSTNOTSTART!

2.C_sethewasherd_r.PresstheSTARTbutt_naga_nt_startthemachine.Attemptt_penthed_r_with_ut exerting excessive

force. THE DOOR MUSTNOT OPEN!

IF THE WASHER STARTS WITH THE DOOR OPEN, OR THE DOOR CAN BEOPENED WHILE THEWASHER ISOPERATING, THE

MA CHINEMUST IMMEDIA TELY BETAKEN OUT OFSERVICE.DISCONNECT THEPOWER CORD,AND MARK THEMACHINE "OUT

OF ORDER", UNTIL THE INTERLOCK SYSTEM IS REPAIRED,AND OPERATESAS DESCRIBEDABO VE.

Avoid fire

hazardor electrical shock.

Do not use an adaptor plug

or extension cord or

remove grounding prong

from electrical power cord.

Failure to follow this

warning can cause serious

injury, fire or death.

Grounding type wall receptacle

Powersupplycor with

CORRECT Use this way ONLY

Do not use or mix

fiquid chlorine bleach with

other household chemicals

such as toilet deaners, rust

removers, acid or products

containing ammonia. These

mixtures can produce

dangerous fumes which can

cause serious injury or death.

Important Safety Instructions Read all instructions before using this washer.

You can be killed or seriously injured if you don't follow these Important Safety Instructions:

• To reduce the risk of fire, electrical shock, or injury to persons when using this washer, comply with the basic warnings listed below.

• Failure to comply with these warnings could result in serious personal injuries.

Prevent Fire

• Do not wash items that have been previously cleaned in, soaked in, or spotted with gasoline, cleaning solvents, kerosene, cooking

oils, waxes, etc. Do not store these items on or near the washer. These substances give off vapors or chemical reactions that could

ignite or explode.

• Do not put oily or greasy rags or clothing on top of the washer. These substances give off vapors that could ignite the materials.

. Do not add gasoline, cleaning solvents, or other flammable or explosive substances to the wash water. These substances give

off vapors that could ignite or explode.

FOR YOUR SAFETY Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or

any other appliance.

. Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for 2 weeks or more.

HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period, before using the washer, turn

on all hot water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas.

Hydrogen gas isflammable; do not smoke or use an open flame during this time.

. Failure to comply with these warnings could result in fire, explosion, serious bodily injury and/or damage to the rubber or plastic

parts of the washer.

Protect Children

• Do not allow children to play on or in the washer. Close supervision of children isnecessarywhen the washer isused near children.

As children grow, teach them the proper, safe use of aNappliances.

• Destroythe carton, plastic bag and other packing materials after the washer isunpacked. Children might usethem for play. Cartons

covered with rugs, bedspreads or plastic sheets can become airtight chambers.

• Keep laundry products out of children's reach. To prevent personal injury, observe all warnings on product labels.

• Before the washer is removed from service or discarded, remove the washer lid to prevent accidental entrapment.

. Failure to comply with these warnings could result in serious personal injuries.

Prevent Injury

.Test door interlock system daily. Follow instructions on previous page.

• To prevent shock hazard and assurestability during operation, the washer must be instaNedand electrically grounded bya qualified

service person in accordance with local codes. Refer to INSTALLATION AND SAFETYINSTRUCTIONSfor detailed grounding

procedures. If the washer is moved to a new location, have it checked and reinstalled by a qualified service person.

.To prevent personal injury or damage to the washer, the electrical power cord of the washer must be plugged into a properly

grounded and polarized 3-prong outlet The third grounding prong must never be removed. Never ground the washer to

a gas pipe. Do not use an extension cord or an adaptor plug.

• FoNow package directions when using laundry products. Incorrect usage can produce poisonous gas--resulting in serious injury

or death.

- Do not combine laundry products for use in 1 load unless specified on the label.

- Do not mix chlorine bleach with ammonia or acids such as vinegar.

. To prevent serious personal injury and damage to the washer:

-All repairs and servicing must be performed by an authorized servicer unless specifically recommended in this

INSTALLATION AND SAFETY INSTRUCTIONS manual. Use only authorized factory parts.

- Donottamperwith controls.

- Do not instaNor store the washer where it win be exposed to the weather.

• To reduce the risk of electric shock, disconnect this appNance from the power supply before attempting any user maintenance.

Turning the controls to the OFFposition does not disconnect this appNance from the power supply.

• To prevent injury, do not reach into the washer while parts are moving. Before loading, unloading or adding items, push in the cycle

selector knob and aNow the tub to coast to a complete stop before reaching inside.

• Failure to comply with these warnings could result in serious personal injuries.

.This washer is equipped with an electrical overload protector. The motor win stop if it becomes overheated. The washer will

automaticaNy restart after a cool down period of up to 30 minutes, if the washer has not been manually turned off during this time.

SAVE THESE INSTRUCTIONS

PRE-INSTALLATION REQUIREMENTS

DRAIN REQUIREMENTS

Tools Required for Installation:

I. 1/4 in. nut driver

2. 3/8 in. socket with ratchet.

3. 3/8 in. open end wrench.

4. 7/16 in. socket with ratchet.

5. 9/16 in. open end wrench.

6. ChanneMock adjustable pliers.

7. Carpenter's level.

ELECTRICAL REQUIREMENTS

CIRCUIT- individual, properly polarized and grounded I 5 amp.

branch circuit fused with 15 amp. time delayfuse or circuit breaker.

POWER SUPPLY- 2 wire, with ground, 120 volt, single phase, 60

Hz,Alternating Current. NOTE:The useof this washer with power

created by gas powered generators, solar powered generators,

wind powered generators or and other generator other than the

local utility company is not recommended.

OUTLETRECEPTACLE - Properly grounded 3-prong receptacle to

be located sothe power supply cord isaccessiblewhen the washer

is in an installed position. NOTE: GFI (Ground Fault Interrupter)

receptacle is not required.

Models equipped with drain pump:

1. Drain MUST be capable of eliminating 17 gals (64.3 L) per

minute.

2. A standpipe diameter of I-I/4 in. (3.18 cm) minimum.

3. The standpipe height above the floor should be:

i! o I

96 in.

(244 cm)

Max.

24 in.

(61 cm)

Min.

GROUNDING REQUIREMENTS

Improper connection of the equipment grounding

conductor can result in a risk of electrical shock. Check with a

licensed electrician if you are in doubt asto whether the appliance

isproperly grounded.

I. The washer MUST be grounded. Inthe event of malfunction

or breakdown, grounding will reduce the risk of electrical

shock by a path of least resistance for electrical current.

Since your washer is equipped with a power supply cord

having an equipment-grounding conductor and a grounding

plug, the plug MUSTbe plugged into an appropriate, copper

wired receptacle that is properly installed and grounded in

accordance with all local codes and ordinances or in the

absence of local codes, with the National Electrical Codes,

ANSI/NFPA 70 (latest edition). If in doubt, call a licensed

electrician.

DO NOTcut off or alter the grounding prong on the power supply

cord. Insituations where a two-slot receptacle is present, it isthe

owner's responsibility to have a licensed electrician replace it

with a properly grounded three prong grounding type

receptacle.

WATER SUPPLY REQUIREMENTS

Hot and cold water faucets MUST be installed within 42 inches

(107 cm) of your washer's water inlet. The faucets MUST be 3/4

inch (I .9 cm) garden hosetype so inlet hoses can be connected.

Water pressureMUSTbe between 10 and 120 pounds persquare

inch (maximum unbalance pressure, hot vs. cold, 10 psi.) Your

water department can advise you of your water pressure.

NOTE:

Drain hose attached to the washer can reach a 58 in. (147 cm)

high standpipe. For higher standpipe usehose P/N 1345.92701,

available from an authorized parts distributor. If drain is less

than 24 in. (61 cm), install a siphon break kit, available at your

local hardware store.

Models equipped with gravity drain:

1. Floor drain MUST be capable of eliminating 17 gals (64.3 L)

per minute.

2. Floor drain diameter must be at least I/2 inch larger than

drain hose.

LOCATION OF YOUR WASHER

See rough-in dimensions on the next page (Figure 1).

DO NOT /NSTALL YOUR WASHER:

1. In an area exposed to dripping water or outside weather

conditions. The ambient temperature should never be below

60 degrees F(15.6 degrees C) for proper washer operation.

2. in an area where it will come in contact with curtains or

drapes.

13. in an area (garage or garage-type building) where gasoline

of other flammables are kept or stored (including

automobiles).

On carpet. Floor MUST be solid with a maximum slope of

1/2 in. per foot (1.27 cm per 30.5 cm). Toensure vibration or

movement does not occur, reinforcement of the floor may

be necessary.

IMPORTANT MINIMUM INSTALLATION CLEARANCES

When installed in alcove: Sides, Rear,Top = 0 in (0 cm).

When installed in closet: Sides, Rear,Top = 0 in (0 cm),

Front = 1 in (2.54 cm).

Closet door ventilation openings required: 2 louvers each 60 in'

(387 cm2)- 3 in (7.6 cm) from top and bottom of door.

(43.2)

ROUGH-iN DIMENSIONS

_._4 3/7 60

3"_(152.4)

(62.9) v

_'(2.54)

1½

)

'POWER

_CORD

331/2

(85)

inch (cm)

(91.5)

43/8

(11.2)_

:20,4)

JNDER

_,OUNTER

345/8

(87.9)

263,4

_ (67.9)

}1,,

....... ii!ii i

BACK

inch (cm)

WATER

iNLETS

31%

(80.3)

(Figure 1).

UNPACKING

1. Cut the shipping carton along the dotted line along tile base

of the unit.

2. While in the carton carefully lay the washer on its back

side.

3. Removethe styrofoam base.

4. Carefully return the washer to an upright position and remove

the carton.

5. Carefully move the washer to within 4 feet (122cm) of the

final location.

6. Remove the following from the back side of the washer:

3 bolts,

3 yellow plastic spacers,

2 or 3 metal "P" clamps.

BOLT

CLAMP

Remove the service panel from the front of the washer.

Remove the 4 nuts and 6 large washers that attach the 2

yellow shipping braces to the drum and the base. Lift up on

the drum and remove the braces (ayellow ribbon surrounds

the items to be removed). These braces must be removed to

allow the power supply cord to be releasedfrom the shipping

ring.

.9. Remove the large styrofoam block located under the drum.

Lift up on the drum, tilt the base of the foam block inwards

toward the rear of the washer until free, then pull it out.

10. Remove and discard the yellow ribbon and label from the

front of the washer.

11. From the rear of the washer, carefully pull out the power

supply cord through the hole in the backsheet.

12. Replace the service panel and screws.

NOTE: If the washer isto be transported at a later date, the

shipping support hardware must be reinstalled to prevent

shipping damage.

INSTALLATION

Run some water from the hot and cold faucets to flush the

water linesand remove particles that might clog up the water

valve screens.

Removethe inlet hoses and rubber washers from the plastic

bag and install the rubber washers in each end of the inlet

hoses.

Carefully connect the inlet hosemarked "HOT" to the outside

"H" outlet of the water valve. Tighten by hand, then tighten

another 2/3 turn with pliers. Carefully connect the other

inlet hose to the inside "C" outlet of the water valve. Tighten

by hand, then tighten another 2/3 turn with pliers. Do not

crossthread or over-tighten these connections.

Connect the inlet hose ends to the HOT and

COLD water faucets tightly by hand, then

tighten another 2/3 turn with pliers. Turn the

water on and check for leaks.

5. Onmachinesequippedwithdrainpump,form

aUshapeontheendofthedrainhose,with

thehosepointedtowardthedrain.

NOTE: If the drain hose isplaced in a standpipe

without forming a U shape, a siphoning action

could occur. There must be an air gap around

the drain hose. A snug hosefit can also cause a

siphoning action.

6. Carefully move the washer to its final location.

NOTE: Do not usethe dispenser drawer or door to lift washer.

Excessivenoise and vibration can be prevented by properly

leveling the washer.

7. Forfree standing installation and with the washer in it's final

position, place a level on top of the washer. Adjust the leveling

legs so the washer is level front-to-rear and side-to-side, and

stable corner-to-corner.

COIN BOX ADJUSTMENT

The tight fit of the money box isset at the factory. Customer may

loosen fit as desired by loosening the slotted nuts. See FIG.2.

FIGURE2 (__0_-<

Slotled Nuts_

Keep A record of aft coin-box key numbers.

A lost key can only be replaced by ordering the key numbers from

the place were the unit was purchased. The key number islocated

both on the key and behind the end panel of the coin box. If the

key number isnot available, the lock must be drilled out to remove

the coin box.

Instructions for Changing Vend Price

TOOLSNEEDED

• Medium sizedslotted screwdriver

• Small slotted Phillips screwdriver

Placeall screws and other items removed from coin slide assembly

on a cloth so they will not get lost.

STEP1

Remove slide mechanism from meter case. (seeFUGURE I).

FIGURE 1

Pressdown on alternate corners and sides and feel for the

slightest movement. Adjust the appropriate leg sothe washer

is SOLIDon the floor on ALL four legs. Keep the leveling leg

extension at a minimum for best performance of the washer.

8. Forpedestal installations, See additional installation

instructions included with the pedestal.

g. Plug the power cord into a grounded outlet.

NOTE: Check to ensure the power is off at the circuit breaked

fuse box before plugging the power cord into an outlet.

10.Turn on the power atthe circuit breakedfuse box.

I 1.Besure you have read the "important Safety Instructions"

before operating this washer.

12.Run the washer through a complete cycle. Check for water

leaks and proper operation.

13. Keep these instructions for future reference.

NOTE: A wiring diagram is located inside the washer on the

side panel.

STEP2

Removethe coin slide extension from coin slide by removing two

mounting screws and spacers

(see FIGURE2).

(2} Mounting Screws

and Spacers

FIGURE2

Slide Return Spring

STEP3

Remove coin slide from coin chute:

• Unhook and remove the coin slide return spring. (see FIGURE2).

, Turn coin slide mechanism upside down.

Remove coin slide stop by taking out two screws to the chute bottom

(see FIGURE3).

(2) Slide Stop

Pull coin slide out of coin chute (seeFIGURE4).

FIGURE4

STEP4

Turn coin slide upside down and remove screw that holds coin receiver

block (see FIGURE5).

(1) Receiver Block Screw

Spare Parts

Compartment

and Screw

STEP5

Remove coin receiver block from coin slide (see FIGURE 6):

• Turn coin slide right side up. Keep coin receiver block in place with

your fingers.

Carefully lift coin slide from coin receiver block. If necessary,shake

coin slide gentlyto loosen block.

STEP6

Setnew vend price byadding or removing the appropriate

block-out keys and/or dime inserts accordinc to th Table

of Vend Prices

(see FIGURE7). FIGURE7

NOTE:

Black

colored

slots are

closed off

by block-

out key.

TABLEOF VEND PRICE

VEND COIN SLOTS

PRICE

2345678

o ||||||||

$.10 D||||B||

$.20 DD=|=|||

$.25 1| B=|| ||

$.35 D|B|I|||

$.45 DD[3|||||

$.50 1| BB |1 1|

$.SO D|[][]||||

$.7o E]E]DB||||

$.75 ||BBB|||

$.85 D|DDB|||

$.95 [] D[] [] []| | |

$1.oo | |[] [] [][] | |

$1.1o D |[] [3[] [] | |

$1.20 DE]B BDB||

$1.25 |[3[] Q[313||

$1.35 [3| [3[] [3[] [3|

$1.45 DDB BBBB|

$1.5o |BBDDBD|

$1.so D[3[3 [3[3[] [3 |

$1.70 [31313[][3 [] [] [3

$1.75 | [] [3[3[3[3 [] []

$1.85 D [] [] [] [] [] [3[3

$2.oo [] [] [3 [] [3 [] [] []

To remove block-out keys, pull straight up.

NOTE: Be sure block-out keys and/or dime inserts are

seated properly and ratchet dog is in place with irsspring

connected (see FIGURE8).

Be sure the proper coin sizing block isin place.

Ratchet

Dog and

Spring

Block-Out

FIGURE8

Changecoinsizingblock:

• Remove two screws that hold upper coin chute cover.

Remove cover (see FIGURE9).

(2) Upper Coin

Chute Cover

FIGURE 9

Anti-Cheat

Gate

Meter Case Instructions

INSTRUCTIONS TO CHANGE THE NUMBER OFCOIN SLIDE

INSERTIONS TOSTARTAPPLIANCE.

1. Disconnect power from machine.

2. Remove meter-case service door. (Fig.l)

FIGURE 10

o Removetwo screws that hold coin sizing block to upper

coin chute cover cover (see FIGURE10).

• Put new coin sizing block in place. Reinsert and tighten

mounting screws.

Replace coin chute cover. Reinsert and tighten screws.

STEP7

Replace coin receiver block into slide:

Hold coin receiver right side up inthe palm of one hand.

• Lower coin slide until coin receiver block fits into the

coin slide cavity. CAUTION: Do not dislodge ratchet dog

and spring.

Hold coin receiver block in place with your fingers and

turn slide upside down.

• Insert and tighten screw.

STEP8

Install slide into coin chute. Slide can only be pushed in if

the anti-cheat gate in flange is pushed to the left. (see

FIGURE9).

STEP9

Replace coin slide stop with two screws. Replace coin

slide return spring. Replacecoin slide extension with two

screws (be sure spacers are in place).

STEP10

Replace coin slide mechanism in meter case. Replaceand

tighten coin slide mounting bolt.

NOTE: It may beeasierto insert coin slide mounting bolt if

you removethe timer from the mounting screwstemporarily.

3. Turn Shaft & CarT]Assembly in a clockwise direction until switch

lever arm drops into cam notch (Fig. 2).

4. Lift Adjusting Tab away from cam with finger and turn Tab to

desired number. Make sure Tab\ locks into place in new position.

5. Turn Shaft & Cam Assembly in a clockwise direction until switch

lever arm ison top of Tab to assurethat both mechanism switches

are open (Fig. 3).

6. Replace meter-case service door and reconnect power to machine.

EXAMPLE: To change from $1 to $2 move tab from 1 to 2,

FIGURE 2 USEFINGER

CAM NOTCH TOLIFTPAD

ADJUSTMENT

TAB

CLOCKVVlSE

DIRECTION

TO LIFT

FIGURE 3

REPLACEMENTPARTS

If replacements parts are needed for your washer, call Sears Parts and Service -roll FreeNumber 1-800-4-MY-HOME

(1-800-469-4663).

For coin box parts seeparts list on pages 10 -11 and call 1-800-221-0982, Greenwald Industries to order.

Destroy the carton and plastic bags after the washer is unpacked. Children might usethem for play. Cartons covered

with rugs, bedspreads, or plastic sheetscan become airtight chambers causing suffocation. Placeall materials in a garbage container

or make materials inaccessible to children.

The instructions in this manual and all other literature included with this washer are not meant to cover every possible

condition and situation that may occur. Good safe practice and caution MUST be applied when installing,operating and maintaining

any appliance.

Maximum benefits and enjoyment are achieved when allthe Safety and Operating instructions are understood and practiced

as a routine with your laundering tasks.

Parts List for series 7682 "Quick-Chanae" Start Mechanism

Item 27A: Models 76-1030-21 (115v-60Hz)q

| 76-1030-22 (230v-60Hz) _

|Item 27B: Models 76-1030-11 (115v-60Hz), I

76-1030-12 (230v-60Hz)

1 2 00-7185 #4-40 SELF-TAPPING SC

2 1 76-6009-* TIMER MOTORASS'Y

3 1 76-1037 SWITCH & BRACKET SUB-ASS'Y

4 1 76-50t4 DRIVE SELEEVE

5 1 76-2033 SLEEVE

6 1 00-8149 TORSION SPRING

7 3 00-7070 RETAINING RING

8 2 76-5013 DRIVE BUSHING

9 1 00-8003 SPRING

10 1 76-1036 RACTHETARM & PAWL ASS'Y

11 1 76-5017 RACHETWHEEL

12 1 76-2003 WASHER

13 1 59-204 SPRING

14 1 76-5012 CAM

15 1 76-5010 ADJUSTER TAB

16 1 00-7055 SPRING WASHER

17 1 00-7047 WASHER

ITE.._MM

18 I

19 2

20 2

26 2

27A 1

27B 1

28 1

29 1

3O 1

PART NO DESCRIPTION

76-2026 DRIVE SHAFT

00-7458 #4-40 3/16 PAN HD SC.

00-7097 #4 SPLIT LOCKWASHER

00-6189 SNAP SWITCH

00-6190 SNAP SW & LEVERARM ASS'Y

76-5009 SWITCH INSULATOR

76-2035 NUT PLATE

76-6000 WIRE HARNESS ASS'Y

02-0810-00 #8-32x5/16 SEMS SCREW

76-2059 MOUNTING BRACKET

76-2027 MOUNTING BRACKET

59-0314 CABLE TtE

58-172-* GROUNDWIRE

00-7558 WASHER

V8 Coin Chute Parts List

V8 Parts List

DESCRIPTION

SCREW (METRIC)

TOP HOUSING

SHIM

COIN SIZING BLOCK

GATE COVER

GATE

20-3000

2 00 9724 00 7924

2 00 7938 00 7938

I 20 3019 20 3002

2 20 2042

f 20 3006 20 3006

I 20 2043 20 2006

F 20 2035 20 2000

8 20 20/I 292011

I 20 4004 20 4000

/ 00 9905 )0 9905

/ 20 3020 20 3000

I 20 302I

I 009/04 009104

4 007483 6_55

I 00 8148 00 8148

i DESCRIPTION

I6iSPRING

17 3PRFNG PROTECTOR

I8 _ACK

19 _CREW (METRIC)

20 _0¢ INSERT varies

22 SHDE STOP

25 SLIDE RATCHET DOG

26 STORAGE COMP COVER

27 SCREW (METRIC)

8 BUFFER

) RATCHET DOG POST

30 COIN RETAINER optional

20-3000

1 20 2040 20 200/ 31

20 2038 20 2007 32

/ 20 2023 20 2005 33

2 00 793/ 00 793/ 34

20 3023 20 500/ 35

2 00 7923 00 7929 37

I 20 2039 20 2004 38

I 00 8123 00 8123 39

20 5002 20 20_0 40

I 20 2041 20 2008 41

20 2037 20 2003

2 00 7935

I 20 2034

20 4005

Opt 00 8168

DESCRIPTION }REQ

3OIN SFZING BLOCK valies I

PRESSURE SPRING AS[_Y i Opt

r_AGNET i Opt

SHIELD IOpt

JOIN RECEIVER BLOCK _ I

LOCK WASHER } /

} I

BCREW (METRIC)

BCREW &,IETRIC )

SCREW

TOP HOUSING ASMY i

20-3020

20 3007

20 /012

00 9256

20 2045

00 7.54/

20 1/03 I

20-3000

20 3007

2010_2

00 9256

20 2045

20 2003

00 7934

00 7933

00 7932

00 7541

201104 I

NEW VEND PRICE

Os!e Fo?m

To change vend price, detach and mail the lower portion to:

Customer Service Department

Greenwald industries Inc,

212 Middlesex Ave.

Chester, CT 06412

Order required parts using this tear-off. Block-out keys will be

shipped to you at no charge. Follow product information

instructions.

Quantity.

Existing Vend Price

Name

The coin chute has been pre-set at the factory.

When increasing in $.25 pricing

Follow product information instructions; no extra parts required.

Company_

Address

City.

StatetZip_

Daytime phone

Purchase date

When decreasing in $.25 pricing - or - changing to

$.10 pricing.

(Coin sizing block required; see "Changing Vend Price"

section.)

SEARS COMMERCIAL WASHER WARRANTY

LIMITED 2-YEAR WARRANTY ON MECHANICAL AND ELECTRICAL PARTS

For two years from the date of purchase, when the washer is installed and operated in accordance with

the instructions in the Installation InstructionslUse & Care Guide, Sears will furnish replacement parts for

all defective mechanical or electrical parts including coin box and chute assemblies. You will be charged

for labor.

WARRANTY SERVICE IS AVAILABLE BY CONTACTING THE NEAREST SEARS SERVICE

CENTER IN THE UNITED STATES.

This warranty applies only while this product is in use in the United States. This warranty gives you

specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179

Kenmore 41727182702 Installation guide

Brand: Kenmore

Model: 41727182702

Type: Installation guide

This manual is also suitable for

41727182704

Download PDF

report

Kenmore 41727182702 Installation guide

This manual is also suitable for

Kenmore 41727182702 Installation guide

Related papers

Other documents