SCRAP
RING
12" CONE
_
12
7
/8"
ALL PIPING
1
/2"
TABLE CUT-OUT:
15" CONE
_
15
7
/8"
18" CONE
_
18
7
/8"
1
/2" FIXED
NOZZLE
FOOD WASTE
DISPOSER
NOTE: INSTALL PER ALL APPLICABLE CODES
DISPOSER
CONTROL
OPTIONAL
CONE COVER
VACUUM
BREAKER
2" OR 3" DRAIN
SOLENOID
VALVE W/
WATER
FLOW
CONTROL
Cone Assembly
FOOD WASTE DISPOSER
SPECIFICATIONS
CORROSION RESISTANT BODY
Permanent molded from heat treated aluminum alloy.
TEFLON LIP WATER SEAL
Protects the motor from damage by water.
TAPERED ROLLER BEARING
Provides longer motor life, quiet operation and
shock absorbing.
WATER COOLED MOTOR
Provides maximum efficiency and longer life.
QUIET OPERATION
Extra thick rubber mounting adaptor and drain
outlet isolates sound and eliminates vibration.
WASTE MIXING CHAMBER
Extra large to ensure proper mixture of water to waste.
■■
■■
208 Volts 3 Phase 19.8 Amps
■■
■■
230 Volts 3 Phase 18.0 Amps
■■
■■
460 Volts 3 Phase 9.0 Amps
FULL LOAD AMPS
◆ SPECIFY EXACT OPERATING VOLTAGE ◆
JOB: Item No.:
NEMA 4 Watertight Controls
Optional Line Disconnect (LD) available on MSS, MRSS, & ARSS
MRSS
MSS
ARSS
ARSS-2
7
1
/
2 H.P. Model 750
The Salvajor Company 4530 East 75th Terrace Kansas City, Missouri 64132-2081, USA
1
-
800
-
SALVAJOR (816) 363
-
1030 FAX
:
1
-
800
-
832
-
9373
www.salvajor.com Email: sales@salvajor.com service@salvajor.com
Manufacturers of Commercial Food Waste Disposing Systems since 1944
Salvajor Model 750
Food Waste Disposer 7
1
⁄2 HP
–
3 Phase
D E T A I L S A N D D I M E N S I O N S
SPECIFICATIONS:
MOUNTING – Rubber adaptor above grind chamber
and rubber drain outlet isolates sound and eliminates
vibration. No metal to metal contact.
EXTERIOR HOUSING – Permanent molded from
heat treated, corrosion resistant aluminum alloy then
c
omputer machined to a smooth polished finish. Paint free.
SHREDDER –10 inch diameter, machined high strength,
wear resistant hardened carbide alloy.
ROTOR – 10 inch diameter with 4 cutter bars, machined
high strength, wear resistant hardened carbide alloy.
MOTOR – 7
1
⁄ 2 HP totally enclosed. Fan cooled and
water cooled for efficiency and longer life.
Built-in manual reset thermal overload protection.
Available in 208-230/460 volts, 60 cycle, 3 phase.
BEARINGS – Tapered roller (top)
Sealed ball (bottom)
SEAL – Teflon Lip Water Seal.
WATER REQUIREMENT – 8 gallons of cold
water per minute.
WASTE OUTLET – Rubber drain accepts 2” piping
or 3” piping by removing drain insert.
DUAL DIRECTION GRINDING – Designed to
operate in either direction. Direction of rotation can be
controlled when installed with automatic reversing controls.
Reversing rotation can double cutting teeth life.
LEG SUPPORT – Single leg, adjustable.
ASSEMBLIES: (See Specification Sheet)
CA – Cone Assembly with 12”, 15” or 18” Cone
SA – Sink Assembly with 3
1
⁄2” or 6
1
⁄2” Sink Collar
DISPOSER CONTROLS: (See Specification Sheet)
MSS: (Non Reversing)
MRSS: (Manual Reversing)
ARSS-2: (Automatic Reversing)
ARSS: (Automatic Reversing)
20
7
/8" (53.02)
5
5
/8" (14.29)
5
5
/8" (14.29)
13
13
/16" (35.08)
1
/2" NPT
W
ATER INLET
1
/2"
FIXED
NOZZLE
19
7
/16"
(49.37)
3
2" (81.28)
TO
35
5
/8"(97.79)
8
1
/2"
(21.59)
2" OR 3"
D
RAIN
2" OR 3"
DRAIN
POWER
ENTRANCE
RESET
BUTTON
6
1
/2"
(16.51)
13"
(33.02)
18" (45.72)
5
5
/8" (14.29)
3
/4" (1.91)
13
1
3
/16" (35.08)
3
1
/2" (8.89)
SINK OPENING
6
5
/8" (16.83)
CUTOUT
1
/2" NPT
WATER INLET
14
9
/16"
(36.99)
8
1
/2"
(21.59)
POWER
ENTRANCE
RESET
BUTTON
13"
(33.02)
17
7
/8" (45.40)
5
5
/8" (14.29)
6
1
/2"
(16.51)
15" (38.10)
1
4
7
/8"
(37.78)
5
5
/8" (14.29)
6
1
/2"
(16.51)
12" (30.48)
26
9
/16" (67.47)
TO
30
3
/16"(76.68)
27
1
/8" (68.90)
TO
30
3
/4"(78.11)
18" CONE 15" CONE
12" CONE
3
1
/2" SINK MOUNT 6
1
/2" SINK MOUNT
Printed in USA
Form No.S750-9-BH
SAMPLE SPECIFICATION
750- CA-18 ARSS
(
230/60/3
)
Model Cone Disposer
Size Control
Assembly
Electrical
Specs.
◆ SPECIFY EXACT OPERATING VOLTAGE ◆
NOTE: Dimensions in parenthesis are in centimeters
(Specifications subject to change without notice)
Current specification details may be found online at www.salvajor.com
/
