Intermatic T171CR Installation guide

Intermatic
Brand
Intermatic
Model
T171CR
Type
Installation guide

This manual is also suitable for

Intermatic T171CR is a 24 HR DIAL TIME SWITCH WITH “SKIPPER®” SINGLE POLE SINGLE THROW (SPST) with a maximum load of 40 AMP. It features 110-125 VOLTS - 60 HZ CLOCK MOTOR. It can be used for various applications such as lighting, appliances, and motors. With its easy-to-use programming instructions, you can set "ON" and "OFF" times, as well as skip operations on selected days. The manual lever allows for easy manual operation. The T171CR is a versatile and reliable time switch that can help you automate your home or business.

Intermatic T171CR is a 24 HR DIAL TIME SWITCH WITH “SKIPPER®” SINGLE POLE SINGLE THROW (SPST) with a maximum load of 40 AMP. It features 110-125 VOLTS - 60 HZ CLOCK MOTOR. It can be used for various applications such as lighting, appliances, and motors. With its easy-to-use programming instructions, you can set "ON" and "OFF" times, as well as skip operations on selected days. The manual lever allows for easy manual operation. The T171CR is a versatile and reliable time switch that can help you automate your home or business.

MODEL: T171
24 HR DIAL TIME SWITCH WITH “SKIPPER®”
SINGLE POLE SINGLE THROW (SPST)
40 AMP. RESISTIVE, INDUCTIVE, TUNGSTEN OR
1000 VA. PILOT DUTY PER POLE - 120/208/240 VOLT AC;
2 HP (24 FLA) - 120V AC; 5 HP (28 FLA) - 240V AC.
WIRING INSTRUCTIONS: To wire switch follow diagram above. Use solid
or stranded COPPER only wire with insulation to suit installation. See
gauge selection table for normal service applications. To make power
connections remove 1/2 inch of insulation from wire ends. Insert bare
ends of wire under the pressure plate of terminals. Use 3/16 or larger
screwdriver to tighten terminal screws firmly. (25 lb-in minimum).
REPLACE INSULATOR BEFORE TURNING ON ELECTRICITY.
PROGRAMMING INSTRUCTIONS
1. TO SET “ON” AND “OFF” TIMES: Hold trippers against edge of
CLOCK-DIAL, pointing to time (AM or PM) when ON and OFF
operations are desired, tighten tripper screws firmly. For additional
tripper pairs on CLOCK-DIAL order 156T1948A.
2. TO SET TIME-OF-DAY: Pull CLOCK-DIAL outward. Turn in either
direction and align the exact time-of-day on the CLOCK-DIAL (the
time now, when switch is being put into operation) to the pointer.
DO NOT MOVE POINTER.
3. TO SKIP OPERATION(S) ON SELECTED DAY(S): Insert SKIPPING
SCREW(S) in SKIPPER WHEEL for day(s) automatic operation(s)
is/are NOT required. Tighten screws firmly. Move MANUAL LEVER to
“OFF” and rotate SKIPPER WHEEL to locate correct day-of-week
opposite DAY ARROW--”YESTERDAY” if ON/CUTOUT TRIPPER
has not yet advanced wheel “TODAY” if it has.
OPERATING INSTRUCTIONS
• TOOPERATESWITCHMANUALLY:Move MANUAL LEVER below
CLOCK-DIAL left or right as indicated by arrows. This will not effect
next operation.
CAUTION: TO AVOID SLOW SWITCH ACTION FAILURE, DO NOT OPERATE
SWITCH MANUALLY NOR PLACE A TRIPPER 4 HOURS PRIOR TO
ON/CUTOUT TRIPPER SWITCHING.
• IN CASE OF POWER FAILURE, reset CLOCK-DIAL to
proper time-of-day. See programming instructions.
INTERMATIC INCORPORATED
SPRING GROVE, ILLINOIS 60081-9698
158TS10952
PRESSURE PLATE
TERMINAL SCREW
MAKE SURE WIRE
INSULATION CLEARS
PRESSURE PLATE
MINIMUM
COPPER
WIRE SIZE
(AWG)
MAX.
LOAD
(AMP)
MIN.
INSUL-
ATION
TEMP(°C)
75°C INSULATION MAX. MOTOR
LOAD (HP)
SINGLE PHASE
3 PHASE
120 V. 240 V. 208 V.
240 V.
14
12
10
8
15
20
30
40
60
60
60
75
1/2
1
2
-
2
2 1/2
3
5
N/A
N/A
TIME
POINTER
TIME
DIAL
OFF
TRIPPER
MANUAL
LEVER
ON/CUTOUT
TRIPPER
DAY
ARROW
SKIPPER
WHEEL
SKIPPING
SCREW
CLOCK MOTOR: 110-125 VOLTS - 60 HZ.
CLOCK MOTOR VOLTAGE AND CYCLE MUST BE AS SPECIFIED. TO
ORDER REPLACEMENT, INDICATE PART NO. (WG--) ON MOTOR COVER.
CLOCK
MOTOR
GROUND
A
1
2
120V
SUPPLY
TO
LOAD
GRD
LINE
WIRING
DIAGRAM
NEUT.
LR3730
  • Page 1 1

Intermatic T171CR Installation guide

Intermatic
Brand
Intermatic
Model
T171CR
Type
Installation guide
This manual is also suitable for

Intermatic T171CR is a 24 HR DIAL TIME SWITCH WITH “SKIPPER®” SINGLE POLE SINGLE THROW (SPST) with a maximum load of 40 AMP. It features 110-125 VOLTS - 60 HZ CLOCK MOTOR. It can be used for various applications such as lighting, appliances, and motors. With its easy-to-use programming instructions, you can set "ON" and "OFF" times, as well as skip operations on selected days. The manual lever allows for easy manual operation. The T171CR is a versatile and reliable time switch that can help you automate your home or business.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents