2. Sunricher
  3. SR-1009FA

Sunricher SR-1009FA, SR-1009FA3, SR-1009FA7 User manual

  • Hello! I've reviewed the user manual for the Sunricher Universal series 09.009FA.04018 RF Receiver. This document provides instructions on how to use the device, which is designed for controlling different types of LED lighting, including RGB/RGBW, single color, and dual color. The manual also explains how to pair the receiver with an RF remote, set up multi-zone controls, and use the master/slave jumper for synchronized effects. I'm ready to assist with any questions you have about the device or its functions.
  • How to pair the RF receiver with a remote?
    How to delete the pairing?
    What is the purpose of the Master/Slave jumper?
whi te
1234
Learn in g Ke y
wwcwwwcw
RF LED controlle r
Universal series RF Receiver
Input
Voltage Remarks
Output
Current
12-36VDC Constant voltage
4x(60-180)W
4x5A
Output
Power
12-36VDC Constant current
4x(4.2-12.6)W
4x350mA
12-36VDC Constant current
4x(8.4-25.2)W4x700mA
No.
1
2
3
Waterproof grade: IP20
Radio Frequency : 868/915/434mhz
Learning Key:
Paring with RF remote
Master/Slave jumper
09.009FA.04018
Function introduction
Important: Read All Instructions Prior to Installation
• DO NOT install with power applied to device.
• DO NOT expose the device to moisture.
whit e
1234
Learning Key
wwcwwwcw
DC Power input
RF LED controller
CH 1:R/WW output
CH 2:G/CW output
CH 3:B/WW output
CH4:W/CW output
Size(LxWxH)
178x46x22mm
178x46x22mm
178x46x22mm
Product Data
Safety & Warnings
Do wiring according to connection diagram.
Pair RF Receiver with RF remote:
1. Connect and wire up the RF receiver correctly, power on.
2. Turn on the remote, click the “Learning Key” button on receiver, immediately click a zone number to pair the
receiver to the specified zone if the remote is a multi-zone controller (if it is a single zone remote, this step is
unnecessary), then touch the color wheel or slider bar on the remote (if the remote does not have color wheel or
slider bar, click or touch any keys), the connected led light on receiver flickers twice, which means well paired.
Note: one receiver can be paired with max 8 remote controls.
Delete the pairing:
1. Wire up the RF receiver correctly, power on.
2. Hold down the “ Learning Key” button on receiver for over 3 seconds until the connected led light on
receiver flickers twice, which means well deleted.
MASTER/SLAVE jumper:
In a group of multiple receivers, in order to get a good sync of RGB running effect, please set only 1 receiver as
MASTER, the other receivers as SLAVE.
After setting the Master, the Master receiver need to power off and on once to make the Master function take
effect.
Operation
With RGB/RGBW color LED
V+ V-
AC Power
50/60Hz
12V/24V/36V
CV PSU
L
N
G
V+
V-
OUTPUT
INPUT
Constant current wall washer light
R-
V+ V+
R-
G- G-
B- B-
V+ V-
With single color LED
With dual color LED
V+ V+
1- V-
2- V-
3- V-
4- V-
If Con nec t wi th Si ngle Co lor LED S tri p
V+ V+
WW WW
CW CW
WW WW
CW CW
If Con nec t wi th Du al Colo r LED Str ip
If Con nec t wi th RG BW LE D St rip
V+ V+
R- R-
G- G-
B- B-
W- W-
V+ V-
AC Power
50/60Hz
L
N
G
V+
V-
OUTPUT
INPUT
V+ V-
AC Power
50/60Hz
L
N
G
V+
V-
OUTPUT
INPUT
whi te
1234
Learn in g Ke y
wwcwwwcw
RF LED controlle r
whi te
1234
Learn in g Ke y
wwcwwwcw
RF LED controlle r
12V/24V/36V
CV PSU
12V/24V/36V
CV PSU
If you use multiple receivers, you have two choices:
Option 1: have all the receivers in the same zone, like zone 1
white
1234
Lear nin g Key
wwcwwwcw
RF LED con tr ol le r
white
1234
Lear nin g Key
wwcwwwcw
RF LED con tr ol le r
Zone 1
Option 2: have each receiver in a different zone, like zone 1, 2, 3 or 4
white
1234
Lear nin g Key
wwcwwwcw
RF LED con tr ol le r
white
1234
Lear nin g Key
wwcwwwcw
RF LED con tr ol le r
Zone 1 Zone 2
white
1234
Lear nin g Key
wwcwwwcw
RF LED con tr ol le r
Zone 3
RF remote
RF remote
whi te
1234
Learn in g Ke y
wwcwwwcw
RF LED controlle r
/