INSTALLATION
CUSTOMER SERVICE
877.370.3604 (toll free)
INSTALLATION QUESTIONS
techsupport@kuryakyn.com
or call 715.247.2983
LIMITED WARRANTY
Küryakyn warrants that any Küryakyn products sold
hereunder, shall be free of defects in materials and
workmanship for a period of one (1) year from the
date of purchase by the consumer excepting the
following provisions:
• Küryakyn shall have no obligation in the event
the customer is unable to provide a receipt showing
the date the customer purchased the product(s).
• The product must be properly installed,
maintained and operated under normal conditions.
• Küryakyn makes no warranty, expressed or
implied, with respect to any gold plated products.
• Küryakyn shall not be liable for any consequential
and incidental damages, including labor and
paint, resulting from failure of a Küryakyn product,
failure to deliver, delay in delivery, delivery in
nonconforming condition, or for any breech of con-
tract or duty between Küryakyn and a customer.
• Küryakyn products are often intended for use
in specific applications. Küryakyn makes no
warranty if a Küryakyn product is used in
applications other than intended.
• Küryakyn electrical products are warranted for
one (1) year from the date of purchase by the con-
sumer. Components of Küryakyn products containing
L.E.D.s will be warranted for defects in materials and
workmanship for 3 years from the date of purchase.
• Küryakyn makes no warranty of any kind in
regard to other manufacturer’s products distributed
by Küryakyn. Küryakyn will pass on all warranties
made by the manufacturer and where possible, will
expedite the claim on behalf of the customer,
but ultimately, responsibility for disposition of the
warranty claim lies with the manufacturer.
ABOUT OUR CATALOG
You’ll find all our innovations for H-D, GL and
Metric Cruisers in our annual catalogs. Order
online today–select the ”CATALOGS” icon. Each
Küryakyn® product comes with a Proof-of-Purchase
good for a complimentary catalog.
Details in packaging.
Be sure to ask your local dealer about other
Küryakyn® products, the motorcycle parts and
accessories designed for riders by riders.
©2005 Küryakyn USA® All Rights reserved.
ATTENTION!
Not suggested for use on bikes with ISO, ISO-Flame or Transformer Grips
currently installed. (Requires removal of existing and purchase of new Kuryakyn grips for
proper installation.)
PARTS INCLUDED
1 Bar End Weight
1 Bar End Plug
1 Large Spacer
1 Small Spacer
1 M6 x 1.0 x 90MM Socket Head Cap Screw (SHCS) (not used in this application)
1 M6 x 1.0 x 75MM Socket Head Cap Screw (SHCS)
1 Installation Instructions
Please read and understand entire instructions before starting installation.
ThANk YOU fOR ChOOSING küRYAkYN!
IN ORDER TO PROTECT YOU AND OThERS fROM POSSIBLE INjURY
AND/OR PROPERTY DAMAGE OR LOSS, PLEASE PAY CLOSE ATTENTION
TO ALL INSTRUCTIONS, WARNINGS, CAUTIONS AND ATTENTION NOTES
REGARDING ThE USE AND CARE Of ThIS PRODUCT.
ATTENTION!
This indication alerts you to the fact that ignoring the contents described herein
may negatively affect product performance and functionality.
TOOLS SUGGESTED
Set of Hex Wrenches, Razor Blade
STRICTLY OBSERVE ThE fOLLOWING GUIDELINES IN ORDER TO USE ThE
PRODUCT PROPERLY AND AVOID POTENTIALLY DANGEROUS ACCIDENTS.
PROCEDURE
STEP 1. Read and understand all steps in the instructions before starting the installation. Park
the motorcycle on a hard, level surface; turn off the ignition and allow the engine to cool.
fOR kURYAkYN GRIPS – NEW GRIPS ONLY
ATTENTION!
Not suggested for use on bikes with ISO, ISO-Flame or Transformer Grips
currently installed. (Requires removal of existing and purchase of new Kuryakyn
grips for proper installation.)
STEP 1 With the left side grip off the motorcycle, remove the 4 screws that hold the end cap
to the grip. Set the hardware and end cap aside.
STEP 2 With the grip still off the motorcycle, thread the bar end plug into the end of the
handlebar and tighten. (PIC 1)
fITS: ’98-UP V STAR 1100 CUSTOM, ’09 V STAR 950, ’07-UP V STAR 1300 INCLUDING
TOURER, ’99-UP ROYAL STAR VENTURE, ’04-UP ROAD STAR 1700 (ALL MODELS), ’06-
UP ROADLINER/STRATOLINER, ’08-UP RAIDER
6287-11MC-0509
ThROTTLE ASSIST MATChING BAR END WEIGhT 6287
-cont.-
INSTALLATION
STEP 3 Insert the large spacer in to the grip and push it to the end of the grip. (PIC 2)
STEP 4 Dry fit (not using any glue) the grip on the handlebar. Check that the spacer at the end of
the grip is sitting against the end of the handlebar.
STEP 5 Mount the grip on the handlebar according to the grip instructions.
STEP 6 Using the 75MM screw supplied, insert the screw in to the Matching Bar End Weight.
(PIC 3)
NOTE
The Small spacer may be needed depending on how/where the grip was mounted
on the handlebar or other accessories used (Handlebar Control Covers, etc.). Check
for proper spacing before tightening screw.
STEP 7 Thread the screw with the Bar End Weight into the handlebar. Tighten the screw.
ATTENTION! It is the installer’s responsibility to ensure that all of the fasteners (including pre-
assembled) are tightened before operation of the motorcycle. Küryakyn will
not issue a warranty on components lost due to improper installation. Periodic
maintenance may be required.
fOR STOCk GRIPS
STEP 1 If your have grips with decorative grip ends or bar end weights, remove them to expose
the bare grip/bar end.
STEP 2 Cut a hole in the end of the grip and thread the Bar End Plug in to the end of the
Handlebar and tighten.
NOTE
You may need to cut the end of the grip to allow the Bar End Plug to be installed.
STEP 3 Cut the end of the grip flush with the Bar End Plug.
STEP 4 Using the 75MM screw supplied, insert the screw in to the Matching Bar End Weight.
STEP 5 Thread the screw with the Bar End Weight into the handlebar. Tighten the screw.
ATTENTION! It is the installer’s responsibility to ensure that all of the fasteners (including pre-
assembled) are tightened before operation of the motorcycle. Küryakyn will not
issue a warranty on components lost due to improper installation. Periodic
maintenance may be required.
PAGE
2
MATChING BAR END WEIGhT
PIC. 1
BAR END PLUG
PIC. 2
LARGE SPACER
PIC. 3
75MM SCREW
/