Clean Water Water Softener 9100-SXT Metered Twin 48K Grain x 2 Installation guide

Brand: Clean Water

Model: Water Softener 9100-SXT Metered Twin 48K Grain x 2

Type: Installation guide

This manual is also suitable for





CleanWaterMadeEasy

www.cleanwaterstore.com



Fleck9100SoftenerInstallation&

Start‐UpGuide

ThankyouforpurchasingaCleanWaterSystem!Withproper

installationandalittleroutinemaintenanceyoursystemwillbe

providingfilteredwaterformanyyears.

YournewsystemcomeswithaprintedFleckServicemanual,which

alongwiththisstart‐upguidewillhelpguideyouintheinstallationand

start‐upofyournewsystem.TheFleckservicemanualcoversothertypesofsystemsaswellsuchaswater

softenersandfilters,sotheremaybeinformationinyourFleckservicemanualthatdoesnotpertaintoyour

system.Pleasereviewthisstart‐upguideentirelybeforebeginningtoinstallyoursystemandfollowthe

stepsoutlinedforbestresults.



Questions?

Callustoll‐free:1‐888‐600‐5426or1‐831‐462‐8500

Emailus:[email protected]

Seemoreinformationonourwebsite:www.cleanwaterstore.com/resources

Fleck9100SoftenerInstallation&StartupGuide

Page2www.cleanwaterstore.comRev030514

TableofContents



PackingList............................................................................................................................................................3

Pre‐Installation......................................................................................................................................................4

BestPracticesforPiping&DrainInstallation........................................................................................................4

Fig1...............................................................................................................................................................5

AddingMedia&InstallationInstructions..............................................................................................................6

Attachingthebrinetubingtothebrinesolutiontank&theFleck9100brinevalve...........................................7

WhattoDoIfYourFilterTankDoesNotSitLevelontheFloor............................................................................8



Fleck9100SoftenerInstallation&StartupGuide

Page3www.cleanwaterstore.comRev030514

PackingList

ModelSize:1.0CubicFootSoftener:

Quantity Description

1 Fleck9100backwashcontrolvalve&bypassvalve

1 Pipeconnectorkit(either1”or¾”)

1 10”x44”filtertankwithdistributortube

1 Mediafunnel

2 ½cubicfootboxesofSoftenerfiltermedia

1 Brinesolutiontank

1 12lbsGravel(ifyouhaveselectedfinemeshresinoption)



ModelSize:1.5CubicFootSoftener:

Quantity Description

1 Fleck9100backwashcontrolvalve&bypassvalve

1 Pipeconnectorkit(either1”or¾”)

1 10”x54”filtertankwithdistributortube

1 Mediafunnel

3 ½cubicfootboxesofSoftenerfiltermedia

1 Brinesolutiontank

1 16lbsGravel(ifyouhaveselectedfinemeshresinoption)



ModelSize:2.0CubicFootSoftener:

Quantity Description

1 Fleck9100backwashcontrolvalve&bypassvalve1 

1 Pipeconnectorkit(either1”or¾”)

1 12”x52”filtertankwithdistributortube

1  Mediafunnel

4 ½cubicfootboxesofSoftenerfiltermedia

1 Brinesolutiontank

1 20lbsGravel(ifyouhaveselectedfinemeshresinoption)



ModelSize:2.5CubicFootSoftener:

Quantity Description

1 Fleck9100backwashcontrolvalve&bypassvalve1 

1 Pipeconnectorkit(either1”or¾”)

1 13”x54”filtertankwithdistributortube

1  Mediafunnel

5 ½cubicfootboxesofSoftenerfiltermedia

1 Brinesolutiontank

1 35lbsGravel(ifyouhaveselectedfinemeshresinoption)

Fleck9100SoftenerInstallation&StartupGuide

Page4www.cleanwaterstore.comRev030514

Pre‐Installation

1. Reviewyourpackinglistandmakesureyouhavereceivedallthepartsbeforebeginninginstallation.

2. Ifyouaregoingtobeturningoffthewatertothehouseandyouhaveanelectricwaterheater,shut

offthepowertothewaterheaterbeforebeginninginstallationincasewaterheaterisaccidentially

drained.

3. Pickasuitablelocationforyourfiltersystemonadrylevelspotwhereitwon’tbeexposedtofreezing

temperatures.Aminimumof20PSIisrequired.Maximumpressureis90PSI.

4. Getallofyourplumbingpartstogetherbeforebeginninginstallation.Installationtypicallytakes3to

5hours.HoweverafterinstallationtheWatersoftenermustbeallowedtorunthroughacomplete

backwashandrinsecycle(alsocalled‘regeneration’).Youdon’thavetobepresentforthisfirst

backwashnecessarily,butitdoestake90minutes.

5. Afterthesystemisinstalledandrunning,youmaynoticesedimentorcolorinyourwater.Thisoccurs

whensedimentthatishasbeeninthepipesforyearsisdislodgedbythesoftwaterorbythesimple

actofturningthewaterpressuronandofftothehouse.Thisrarelylastsformorethanafewhours

toafewdaysbutifyouhaveoldgalvanizedironpipeandtherustorcolordoesnotstopafterafew

daysitmaymeanthatyourpipesarecorrodedordeteriorated.



BestPracticesforPiping&DrainInstallation

1. Seetypicalinstallation(seeFig1).Thewatersoftenerisinstalledafterthepressuretank.

2. MakesuretoconnecttheinletpipetotheFleck9100inletandtheoutlettotheoutlet(seeFig2).

Youcanseetheinandoutarrowsonthebypassvalvewhichiswherethepipesareconnected.

3. Makesurethereisaworkinggateorballvalvebeforethewatersoftenerandalsooneafterasshown

inthediagram.Ifyouareinstallingmultiplefiltersystems(suchasironfilterthenwatersoftener)

youdonotneedavalveinbetweeneachsystem.Thepressuregaugesareoptionalandnot

necessarybutahosebib(whichisafaucetthatyoucanattachagardenhoseto)isstrongly

recommendedafterthewatersoftenerbeforethesecondballvalve.Thismakesiteasytorinseyour

newsofteneronstart‐upandgivesyouaplacetotestthewaterbeforeitentersyourhousehold

plumbing.

4. Ifyouwillbeusingcopperpiping,donotsweatthecopperpipedirectlyontotheFleck9100bypass

valve.Avoidheatingupthebypassvalvewiththetorch.

5. Youdonotneedunionstoinstallyourwatersoftener.Ifyouneedtoremoveit,theFleck9100has

quick‐releasecouplingsonthebypassvalvethatmakeiteasytoputthewatersofteneronby‐pass

andremovethefiltersystemfromthepiping.

Fleck9100SoftenerInstallation&StartupGuide

Page5www.cleanwaterstore.comRev030514

6. Thedrainlinetubing(notsupplied)isconnectedtoadrainfromthedrainoutletusingflexible½”ID

tubing.NotethatthedraincanrunupabovetheFleck9100controlandintoadrain,itdoesnot

havetodraindown,asthefilterbackwashesunderlinepressurefromyourwellpump.Most

plumbingcodesrequireanair‐gapconnection,sothatifyoursewerorseptictankbacksup,itcannot

crossconnectwiththedraintubing.

7. Usuallyyoudonotwanttowaterthegardenorirrigateyourlandscapingwithsoftenedwater.This

willrequiremoresaltthanusualtobeusedandinsomecasesthesodiumcanbuild‐upinthesoil

causingsomeproblemstosensitiveplants.Itisoftennotdifficulttorunhardwater(not‐softened

lines)totheirrigationtherebybypassingthewatersoftener.Ifyoudowanttoirrigatewithsoftwater

werecommendyouusepotassiumchloridesalt(widelyavailable)insteadofregularsodiumchloride

(watersoftenerrocksalt).Anytypeofsaltthoughcanbeusedinthewatersoftener.



Fig1‐Typicalwatersoftenerpipinginstallationwithballvalveandhosebibafterthefilter



Fleck9100SoftenerInstallation&StartupGuide

Page6www.cleanwaterstore.comRev030514

AddingMedia&InstallationInstructions

1. UnscrewbyhandtheFleck9100controlvalvefromtopofthetanksifitwasshippedscrewedon.

Placedistributortubesintankifnotalreadyinsidetanks.Ifnotalreadydone,makesurebluecapis

ontopofdistributortubes,orwrapthetopofdistributortubeswithelectricalorducttape.Theidea

iswedonotwantgravelorresintogodownthedistributortubewhenyouareaddingmedia.

2. Ifyoursystemcamewithfiltergravel,additfirstusingthefunnelsentwiththewatersoftener.

Dividegravelequallybetweentanks.



3. Nextaddsoftenerresinmedia.Tankwillbeapproximately2/3to3/4full.Divideresinprovideequally

betweentanks.

4. Removecaportapefromtopofdistributortube.Becarefulnottopullupdistributortubewhen

removingcaportape.

5. Attachplastictopscreentotheunder‐sideoftheFleck7000controlvalve.Itisafunnel‐shaped

plasticscreenthatsnapsontothecontrolvalveandpreventsresinfrombeingbackwashedoutto

drainduringtheregenerationcycles.



6. Ifpossibleatthispoint,filltankcompletelywithwater.Thiswillallowthesoftenerresintosettleand

eliminatetheneedof“purging”theairoutofthetanklater.

Plugortapetopofdistributortubeto

preventmediafromentering.Remove

cap/tapewhenfinished

Fleck9100SoftenerInstallation&StartupGuide

Page7www.cleanwaterstore.comRev030514

7. AddasmallamountofvegetablecookingoiltothetankthreadsandscrewonFleck9100control

valvecarefully.Alternativelyyoucanusesiliconegrease,butdonotusepipe‐jointcompound,Teflon

tape,orVaselineorotherpetroleumgreasestolubricatetankthreads.

8. SeehowtheFleckby‐passisconnected.Thereareinandoutarrowsonthebypassvalvefortheinlet

andoutletpipe.Installinletandoutletpiping,draintubingandbrinelinetubing.Thebrinelinetube

isincludedandisshippedinsidethebrinetank.

Attachingthebrinetubingtothebrinesolutiontank&theFleck9100brinevalve



9. Beginbyslidingtheplasticbrineinjectornutontothebrinetubingbyputtingthetubingthroughthe

non‐threadedsideofthenut.Next,slidetheblack(orclear)compressionringontothetubingwith

thenarrowerdiametergoingonfirst.Thenslidethetaller,whitecompressionringontothetubing

withthewiderdiametergoingonfirst.Thetwocompressionringsshouldlayfleshagainsteachother

onthetubing.Slidethemintothebrineinjectornutandplacethebrinetubingintothebrinevalve.

Finally,pushthebrineinjectornut,whichnowhasthecompressionringsinsideofit,ontothe

threadingofthebrinevalveandrotatethenutclockwise,screwingitontothebrinevalve.Tightenit

downtofingertightness.Thetubingshouldbefirmlyattachedandnotslideoutifpulledon.



Fleck9100SoftenerInstallation&StartupGuide

Page8www.cleanwaterstore.comRev030514

10. Notethattheover‐flowfittingonthesideofthebrinetankdoesnotneedtobeconnected,unless

thesoftenerisinstalledinaclosetorsomewherewhereoverflowingsaltwatercouldcausea

problem.Waterrarelyoverflowsfromthebrinetankhowever.

11. Addapproximately5gallonsofwatertobrinetank,thenfillbrinetankabout2/3fullofsalt.ItisOK

touseanykindofwatersofteningsalt;howeverwefindthatextracoarsesaltworksbetterthanthe

pellets.Youdonothavetoaddwatertothebrinetankagainafterthisfirsttimeduringthestart‐up.

12. Closethevalveafterthewatersoftener.Connectagardenhosetothehosebibafterthesoftener

andopenhosebib.Turnonthewatertothesoftenerandallowthewatertorunoutthegarden

hoseuntilthewaterisclear.

13. SeetheFleck9100ServiceManualforinstructionsonhowtoprogramandsetsoftener.YourFleck

9100isalreadyprogrammedforthesizetankyouhave,butyoudoneedtosetthecurrenttimeof

dayandprogramthewatersoftenerwithyourwaterhardness.Whenprogrammingadd2or3

grainsofhardnesstoyourwaterhardnessasasafetymeasureifyouhaveironinthewater.

14. StartamanualbackwashbypressingandholdingtheExtraCyclebuttonfor5seconds.Aftersoftener

hasbeenregeneratingfor20minutes,lookinsidethebrinetank,andyoushouldseethatishas

suckedoutthebrine.Attheendoftheregeneration(90minutes)checktomakesurethatthe

softenerhasaddedwatertothebottomofthebrinetanktomakebrineforthenextregeneration

cycle.

WhattoDoIfYourFilterTankDoesNotSitLevelontheFloor

Yourblackfiltertankbaseisnotgluedtothebottomofyourtank.Occasionallytankbaseswillbecome

crookedduringshipment.Ifyoufindthatthatyourtankdoesnotsitlevelonthefloor,youcaneasilyadjustit

byholdingtheemptytankandrappingitonaconcreteorsolidflooronceortwiceinordertolevelit.





Clean Water Water Softener 9100-SXT Metered Twin 48K Grain x 2 Installation guide

Brand: Clean Water

Model: Water Softener 9100-SXT Metered Twin 48K Grain x 2

Type: Installation guide

This manual is also suitable for

Download PDF

report

Clean Water Water Softener 9100-SXT Metered Twin 48K Grain x 2 Installation guide

This manual is also suitable for

Clean Water Water Softener 9100-SXT Metered Twin 48K Grain x 2 Installation guide

Related papers

Other documents