Real Fyre G9 Owner's manual

Real Fyre
Brand
Real Fyre
Model
G9
Type
Owner's manual

This manual is also suitable for

Real Fyre G9 Golden Oak Designer & Split Oak [9] Log is a revolutionary gas log set that offers the beauty and ambiance of a traditional wood-burning fireplace without the mess and hassle. This vent-free gas log set is designed to be used with a Peterson G9 burner and features realistic logs that are made from a durable, high-density ceramic material. The logs are hand-painted to create a lifelike appearance, and they produce a beautiful, natural-looking flame.

The Real Fyre G9 Golden Oak Designer & Split Oak [9] Log is easy to install and operate. Simply place the logs on the burner and turn on the gas. The logs will ignite automatically, and you can adjust the flame height to your liking. The logs will remain hot for several hours after the gas is turned off, so you can enjoy the warmth and ambiance of a fire even after the flames have died down.

Real Fyre G9 Golden Oak Designer & Split Oak [9] Log is a revolutionary gas log set that offers the beauty and ambiance of a traditional wood-burning fireplace without the mess and hassle. This vent-free gas log set is designed to be used with a Peterson G9 burner and features realistic logs that are made from a durable, high-density ceramic material. The logs are hand-painted to create a lifelike appearance, and they produce a beautiful, natural-looking flame.

The Real Fyre G9 Golden Oak Designer & Split Oak [9] Log is easy to install and operate. Simply place the logs on the burner and turn on the gas. The logs will ignite automatically, and you can adjust the flame height to your liking. The logs will remain hot for several hours after the gas is turned off, so you can enjoy the warmth and ambiance of a fire even after the flames have died down.

1
CAUTION...............WARNING...............IMPORTANT
USE ONLY A PETERSON REAL FYRE G9 BURNER WITH THIS REAL FYRE LOG SET.
Important: Adequate spacing between the
logs is NECESSARY and MUST be
maintained. If carbon build up (sooting)
exists, correct log placement before
sooting becomes worse. If any sooting
occurs outside of the fi rebox (i.e. on
the walls), turn off unit immediately
and contact a qualifi ed professional
service technician.
WARNING: Use ONLY a Peterson Real Fyre
G9 burner with this Real Fyre gas log
set. Failure to do so may result in
property damage or personal injury,
and will void listings, certifi cations,
and invalidate claims made to RHP.
Contact your local Real Fyre dealer if you
need more information.
This instruction contains log set placement for these Real Fyre logs. You must position and maintain the log
layout as shown here to ensure proper operation of the burner system. Incorrect log installation could cause
fl ame impingement and improper combustion, resulting in soot and/or excessive by-products of combustion.
DO NOT add any additional embers for this installation. Any additional embers will cause unsafe operation.
Use these logs only with a Peterson G9 burner system.
If you experience an accumulation of black carbon (soot) on your logs it is an indication of incomplete
combustion and you must correct the log placement as instructed in this manual. If signifi cant sooting
continues, stop using this gas log set.
Please read these instructions completely and carefully.
This product is only warranted when used as part of a
Robert H. Peterson Co. unvented burner system.
ROBERT H. PETERSON CO. • 14724 East Proctor Avenue • City of Industry, CA 91746
LOG SET IMPORTANT INFORMATION
L-F2-127REV 0 - 1908161325
GOLDEN OAK DESIGNER & SPLIT OAK LOG PLACEMENT INSTRUCTIONS
RD9-24 shown
2
Failure to use a Peterson G9 burner may result in a DANGEROUS situation
and in property damage, personal injury or even death, will void listings
and certifi cations, and will void any insurance coverage by R.H. Peterson
Co. or our insurers.
CAUTION: Burn hazard! Logs will remain hot for some time after use.
If you need to reposition any log to maintain the proper layout,
use heat resistant gloves or allow logs adequate time to cool
before handling.
WARNING: This gas log set is for use with an R.H. Peterson Co. G9
burner (and parts) ONLY.
L-F2-127REV 0 - 1908161325
3
GOLDEN OAK DESIGNER & SPLIT OAK LOG PLACEMENT INSTRUCTIONS (20", 24", & 30" MODELS)
III
III
IV
(RD,S)9-(20,24,30)
PARTS LIST
RD9-24 log set shown
1
2
4
3
5
6
20" & 24" - (RD,S)L9-17BR
30" - (RD,S)L9-20BR
20" - (RD,S)L9-20BF
24" - (RD,S)L9-24BF
30" - (RD,S)L9-30BF
(RD,S)L9-10TY
(RD,S)L9-9TY
Place the rear log (log #1) as shown. Slide it forward on
the burner, against the main burner bracket. ENSURE
THE LOG RESTS FLAT ON THE BURNER, AND THAT
THE BURNER BRACKET ALIGNS WITH THE GROOVES
FOUND ON THE FACE OF THE LOG.
2
Place the front log (log #2) as shown. The underside of
the log has two tabs that insert into the holes found on the
burner. The cutouts found on the underside of the log will
align over the grate fi ngers. ENSURE THE LOG RESTS
FLAT ON THE BURNER/GRATE.
Ensure the rear and front logs are snug up against the main
burner bracket.
V
Place the left middle log (log #3) as shown. The log should
lock in place over the logs below.
Place the center middle log (log #4) as shown. The log
should lock in place over the logs below.
(RD,S)L9-10TC
7
RDL9-11TL
SL9-11T
(RD,S)L9-10TR
1
Logs snug against bracket
The underside of the bottom logs have cutouts and tabs that align over the burner. THE BOTTOM LOGS
MUST BE FULLY SEATED ON THE BURNER. Certain logs have notches on them to allow for the logs to
interlock in place.
All items for this log set are included in one (1) box.
CAUTION: Burn hazard! Logs will remain hot
for some time after use.
3
4
Align
notches
with
bracket
Align tabs
with holes
4
After setting the logs into position as described above, ensure each is properly and fi rmly seated. The
vent-free gas log set will not function as intended if the logs are not correctly positioned. When placed
properly, the fl ames will not strike any portion of the logs. Periodically check the positioning of all logs to
ensure proper log placement and stability. If any fl ame is striking the logs, recheck log placement. Adjust
to conform with instructions. There should be no fl ame impingement on the logs.
GOLDEN OAK DESIGNER & SPLIT OAK LOG PLACEMENT INSTRUCTIONS (20", 24", & 30" MODELS) (CONT.)
Place the right middle log (log #5) as shown. The
log should lock in place over the logs below.
V
VI
Place the left top log (log #6) as shown. The log
should lock in place over the logs below.
6
5
Place the right top log (log #7) as shown. The log
should lock in place over the logs below.
VII
7
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Real Fyre G9 Owner's manual

Real Fyre
Brand
Real Fyre
Model
G9
Type
Owner's manual
This manual is also suitable for

Real Fyre G9 Golden Oak Designer & Split Oak [9] Log is a revolutionary gas log set that offers the beauty and ambiance of a traditional wood-burning fireplace without the mess and hassle. This vent-free gas log set is designed to be used with a Peterson G9 burner and features realistic logs that are made from a durable, high-density ceramic material. The logs are hand-painted to create a lifelike appearance, and they produce a beautiful, natural-looking flame.

The Real Fyre G9 Golden Oak Designer & Split Oak [9] Log is easy to install and operate. Simply place the logs on the burner and turn on the gas. The logs will ignite automatically, and you can adjust the flame height to your liking. The logs will remain hot for several hours after the gas is turned off, so you can enjoy the warmth and ambiance of a fire even after the flames have died down.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents