Simplicity MANUAL, GEN, INVERTER, B&S, P3400, 030808 User manual

Brand: Simplicity

Model: MANUAL, GEN, INVERTER, B&S, P3400, 030808

Category: Power generators

Type: User manual

This manual is also suitable for

030808-00

Not for

Reproduction

Manual No. 80098186 Revision A

Outdoor Portable Generator

Operator’s Manual

Model Number _____________________________

Revision __________________________________

Serial Number ______________________________

Date Purchased ____________________________

1800-356-632 (AUS) or 0800-484-282 (NZ)

BRIGGSandSTRATTON.com.au

Not for

Reproduction

2 BRIGGSandSTRATTON.com.au

Equipment Description

Table of Contents

Equipment Description.........................2

Features and Controls .........................4

Operation....................................6

Maintenance ................................11

Storage ....................................14

Troubleshooting/Specifications .................15

Warranty ...................................16

Symbols and Meanings

Signal Meaning

DANGER

Indicates a hazard which, if not avoided, will

result in death or serious injury.

WARNING

Indicates a hazard which, if not avoided, could

result in death or serious injury.

CAUTION

Indicates a hazard which, if not avoided, could

result in minor or moderate injury.

NOTICE

Indicates information considered important, but

not hazard-related.

Symbol Name Explanation

Safety Alert

Symbol

Indicates a potential personal injury

hazard.

Operator’s

Manual

Failure to follow warnings,

instructions and operator’s manual

could result in death or serious

injury.

Toxic Fumes

Engine exhaust contains carbon

monoxide, a poisonous gas that

could kill you in minutes. You

cannot smell it or see it.

Fire

Fuel and its vapors are extremely

flammable which could cause

burns or fire resulting in death or

serious injury.

Engine exhaust could cause fire

resulting in death or serious injury.

Electric

Shock

Generator could cause electrical

shock resulting in death or serious

injury.

Hot Surface

Muffler could cause burns or

resulting in serious injury.

Equipment Description

Read this manual carefully and become familiar

with your outdoor generator. Know its applications,

its limitations, and any hazards involved. Save

these original instructions for future reference.

The outdoor generator is an engine–driven, revolving

field, alternating and direct current (AC & DC) generator.

It was designed to supply electrical power for operating

compatible electrical lighting, appliances, tools and motor

loads. The generator’s revolving field is driven by a single-

cylinder engine.

The portable generator can be used to power outdoor

items using an extension cord or to restore home power

using a transfer switch. A transfer switch is a separate

device installed by a licensed electrician that allows

the portable generator to be cord connected, using the

receptacle, directly into your home’s electrical system.

Install a manual transfer switch as soon as possible if

generator will be used to provide home power restoration.

The generator is not intended to supply systems that are

legally required, for serious life safety or health hazards,

or where lack of power hampers rescue of fire-fighting

operations.

Every effort has been made to ensure that the information

in this manual is both accurate and current. However,

the manufacturer reserves the right to change, alter or

otherwise improve the generator and this documentation at

any time without prior notice.

NOTICE If you have questions about intended use,

contact an authorized service dealer. This equipment is

designed to be used with Briggs & Stratton® authorized

parts only.

System Ground

The generator has a system ground that connects the

generator frame components to the ground terminals on

the AC output receptacles. The generator neutral is floating,

which means that the AC stator winding is isolated from

the grounding fastener and the AC receptacle ground pins.

Electrical devices, such as RCD, requiring a grounded

neutral may not operate properly from this generator.

Earthing of the generator is not required.

Special Requirements

There may be regulations, local codes, or ordinances that

apply to the intended use of the generator. Please consult

a qualified electrician, electrical inspector, or the local

agency having jurisdiction.

This generator is not intended to be used at a construction

site.

Not for

Reproduction

Equipment Description

Air Cleaner — Filters engine intake air.

Choke Lever — Used when starting a cold engine.

Engine Switch — Set this switch to ON (I) before using

recoil starter. Set switch to OFF (0) to stop engine. Also

turns fuel valve on and off.

Fuel Cap — Add unleaded fuel here.

Grounding Fastener — Consult your local agency having

jurisdiction for grounding requirements in your area.

Identification Label — Provides model and serial number of

generator.

Oil Fill Cap — Check, add and drain engine oil here.



this button to turn the QPT on and off.

Recoil Starter — Used to start the engine manually.

Retractable Handle — Press button and pull handle out to

move generator. Press button to push handle back in.

Side Maintenance Cover — Remove to gain access to the

air cleaner and oil service.

Spark Arrester Muffler/Exhaust — Lowers engine noise and

is equipped with a spark arrester screen.

Statstation™ LCD Screen — Built in LCD screen to monitor

certain features on the generator. See STATSTATION™.

Top Maintenance Cover — Remove to gain access to the

spark plug.

Fuel Cap

Grounding Fastener

Air Cleaner (under cover)

Side Maintenance Cover

Identification Label

Engine Switch

Recoil Starter

Spark Arrester Muffler/Exhaust

Statstation™ LCD Screen

QPT Switch

Oil Fill Cap (under cover)

Retractable Handle

Top Maintenance Cover

Choke Lever

Not for

Reproduction

4 BRIGGSandSTRATTON.com.au

Features and Controls

12 Volt DC Receptacle — Use this receptacle to supply

power for 12 Volt DC accessories that are rated 60 watts

(5 Amp) or less. This receptacle is protected by a push to

reset circuit breaker.

230 Volt AC, 15 Amp Receptacle — May be used to supply

electrical power for the operation of 230 Volt AC, 15 Amp,

single phase, 50 Hz electrical, lighting, appliance, tool, and

motor loads.

Carbon Monoxide (CO) Shutdown Indicator Light —

Indicates the engine shutdown due to carbon monoxide

accumulation around the generator or a CO shutdown

system fault occurred.

Circuit Breaker — A “push to reset” circuit breaker is

provided to protect the generator against electrical

overload.

DC Circuit Breaker — The 12 Volt DC receptacle is

provided with a “push to reset” circuit breaker to protect the

generator against electrical overload.

Parallel Operation Port — Use this port with optional

parallel operation kit to connect and combine the output of

two generators.

USB Ports — Use ports to recharge most USB powered

devices.

Compare the illustrations with your generator to familiarize yourself with the locations of various controls and product warnings.

Circuit Breaker

Carbon Monoxide

(CO) Shutdown

Indicator Light

USB Ports

DC Circuit Breaker

12 Volt DC Receptacle

Parallel Operation

Port

230 Volt AC, 15

Amp Receptacle

Not for

Reproduction

Exhaust/muffler

Point away from home

Features and Controls

Not for

Reproduction

6 BRIGGSandSTRATTON.com.au

Operation

Step 1: Safe Location

Before starting the portable generator there are two equally

important safety concerns regarding carbon monoxide

poisoning and fire that must be addressed.

Operation Location to Reduce the Risk of

Carbon Monoxide Poisoning

The engine exhaust of all fossil fuel burning equipment,

such as a portable generator, contains carbon monoxide,

a poisonous gas that could kill you in minutes. You cannot

smell it, see it, or taste it. Even if you do not smell exhaust

fumes, you could still be exposed to carbon monoxide gas.

By law it is required in many states to have a carbon

monoxide alarm in operating condition in your home.

A carbon monoxide alarm is an electronic device that

detects hazardous levels of carbon monoxide. When there

is a buildup of carbon monoxide, the alarm will alert the

occupants by flashing visual indicator light and alarm.

Smoke alarms cannot detect carbon monoxide gas.

WARNING! Engine exhaust contains carbon

monoxide, a poisonous gas that could kill you

in minutes. You cannot smell it, see it, or taste it.

Even if you do not smell exhaust fumes, you could still be

exposed to carbon monoxide gas.

• Operate portable generator only outdoors, at least

6.1 m (20 ft.) from occupied spaces with exhaust

pointed away to reduce the risk of carbon monoxide

accumulating.

• Install battery-operated carbon monoxide alarms or

plug-in carbon monoxide alarms with battery back-up

according to the manufacturer’s instructions. Smoke

alarms cannot detect carbon monoxide gas.

• Do not run portable generator inside homes, garages,

basements, crawlspaces, sheds, or other partially-

enclosed spaces even if using fans or opening doors

and windows for ventilation. Carbon monoxide can

quickly build up in these spaces and can linger for

hours, even after this product has shut off.

If you start to feel sick, dizzy, weak, or your homes carbon

monoxide alarm sounds while using this product, get to

fresh air right away. Call emergency services. You may have

carbon monoxide poisoning.

To better educate yourself about all carbon monoxide risks,

go to www.takeyourgeneratoroutside.com.

6.1 m (20 ft.)

min.

Carbon Monoxide Alarm(s)

Install carbon monoxide alarm

inside your home. Without

working carbon monoxide alarms,

you will not realize you are getting

sick and dying from carbon

monoxide poisoning.

Prevent Carbon Monoxide (CO) Poisoning

• Use outdoors at least 6.1 m (20 ft.) from any home.

• Point exhaust away from all homes and occupied spaces.

• Install CO alarms inside your home.

Not for

Reproduction

Operation Location to Reduce the Risk of Fire

WARNING!

Exhaust heat/gases could ignite

combustibles, structures or damage fuel tank

causing a fire, resulting in death or serious injury.

• Portable generator must be at least 1.5 m (5 ft.) from any

structure, overhang, trees, shrubs, or vegetation over

30.5 cm (12 in.) in height.

• Do not place portable generator under a deck or other

type of structure that may confine airflow. Smoke alarm(s)

must be installed and maintained indoors according to the

manufacturer’s instructions/recommendations.

• Carbon monoxide alarms cannot detect smoke.

• Do not place portable generator in manner other than

shown.

Step 2: Oil and Fuel

1. Move generator outdoors to a flat, level surface.

2. Loosen the two maintenance cover screws and

remove the side maintenance cover.

3. Clean area around oil fill and remove yellow oil fill cap.

4. Using an oil funnel, slowly pour contents of oil bottle

into oil fill opening. Checking oil level frequently, fill to

point of overflowing.

NOTICE Pause to permit oil to settle. DO NOT overfill.

5. Replace and fully tighten oil fill cap.

6. Replace the side maintenance cover and hand tighten

the two maintenance cover screws.

Low Oil Indicator

The low oil indicator system is designed to prevent engine

damage caused by not enough engine oil. If the engine

oil level drops below a preset level, the yellow LED low

oil indicator light comes on and an oil switch will stop

the engine. If the engine stops or the yellow LED low oil

indicator light comes on when you pull the recoil handle,

check the engine oil level.

Fuel must meet these requirements:

• Clean, fresh, unleaded fuel with a minimum of 91 RON

(87 octane/87 AKI).

• Gasoline with an ethanol content up to 10% is acceptable.

E10

E15

NOTICE Do not mix oil in fuel or modify engine to run on

alternate fuels. Use of unapproved fuels could damage

engine and will not be covered under warranty.

See High Altitude for 1524 m (5,000 ft.) and above.

WARNING! Fuel and its vapors are extremely

flammable which could cause burns or fire

resulting in death or serious injury.

• Do not refuel during operation.

• Do not smoke during refueling.

• Turn engine off and let it cool at least 2 minutes before

removing fuel cap.

• Fill fuel tank outdoors. Keep fuel away from sparks, open

flames, pilot lights, heat, and other ignition sources.

Check fuel lines, tank, cap and fittings frequently for

cracks or leaks. Replace if necessary.

7. Slowly remove fuel cap to relieve pressure in tank.

Operation

MUFFLER

6.1 m (20 ft.) min.

1.5 m

(5 ft) min.

1.5 m (5 ft) min.

Not for

Reproduction

8 BRIGGSandSTRATTON.com.au

8. Slowly add unleaded fuel to red fuel level indicator in

fuel tank. Be careful not to fill above the indicator. This

allows adequate space for fuel expansion.

9. Install fuel cap and let any spilled fuel evaporate

before starting engine.

High Altitude

At altitudes over 1524 m (5,000 ft.), a minimum 89 RON

(85 octane/85 AKI) fuel is acceptable. To remain emissions

compliant, high altitude adjustment is required. Operation

without this adjustment will cause decreased performance,

increased fuel consumption, and increased emissions.

See an authorized Briggs & Stratton dealer for high altitude

adjustment information. Operation of the engine at altitudes

below 762 m (2,500 ft.) with the high altitude kit is not

recommended.

Transporting

When transporting equipment, turn engine switch to off

position. Do not tip engine or equipment at an angle which

causes fuel to spill.

Step 3: Generator Start Up

Turn off all electrical loads connected to the generator. Use

the following start instructions:

1. Make sure unit is outdoors on a level surface.

NOTICE Failure to operate the unit on a level surface may

cause the unit to shut down.

2. Turn the engine switch to the ON (I) position.

3. Push choke lever to CHOKE ( ) position.

4. Grasp recoil handle and pull slowly until slight

resistance is felt. Then pull rapidly to start engine.

• If engine starts, proceed to step 6.

• If engine fails to start, proceed to step 5.

WARNING!

Starter cord kickback (rapid retraction)

will pull hand and arm toward engine faster than you

can let go which could cause broken bones,

fractures, bruises, or sprains resulting in serious injury.

• When starting engine, pull cord slowly until resistance is

felt and then pull rapidly to avoid kickback.

• NEVER start or stop engine with electrical devices

plugged in and turned on.

5. Move choke lever to half choke position, and pull recoil

handle twice.

• If engine fails to start, repeat steps 3 thru 4.

Slowly move choke lever to RUN ( ) position. If engine

falters, move choke lever to half choke position until

engine runs smoothly, and then to RUN ( ) position.

NOTICE If engine floods, move choke lever to RUN ( )

position and crank until engine starts.

NOTICE If engine starts after 2 pulls but fails to run, or if

unit shuts down during operation, make sure unit is on a

level surface and check for proper oil level in crankcase.

This unit is equipped with a low oil protection device. If so,

oil must be at proper level for engine to start.

Step 4: Connecting Electrical Loads

To Restore Home Power Using a Transfer Switch

Connections to your home’s electrical system must use a

manual transfer switch installed by a qualified electrician. The

connection must isolate the generator power from the utility

power and comply with all applicable laws and electrical codes.

To Restore Power Using Extension Cords

Generator may only be loaded up to rated power under the

rated conditions as shown on unit data tag. Reduce load

when using generator outside of rated conditions.

Use only high quality, well-insulated extension cables in

accordance with IEC 60245-4 with the generator’s 230

Volt AC outlets. Inspect extension cables before each use.

Check that all extension cables are suitably rated and are

not damaged. When using extension cords under 40° C,

the total length of cords for a cross section of 1.5 mm²

should not exceed 60 m or for a cross section of 2.5 mm²

should not exceed 100 m.

WARNING! Damaged or overloaded extension

cords could overheat, arc, and burn resulting in

death or serious injury.

• Electrical equipment, including cables and plug

connections, should not be defective.

1. Install carbon monoxide alarm(s).

2. When operating generator with extension cords, make

sure it is located in an open, outdoor area, at least 6.1

m from occupied spaces with exhaust pointed away.

3. Extension cords running directly into home, powering

indoor items IS NOT RECOMMENDED.

Operation

Engine switch

Choke lever

Fuel Level

Indicator

Not for

Reproduction

Operation

WARNING! Engine exhaust contains carbon

monoxide, a poisonous gas that could kill you in

minutes. You cannot smell it, see it, or taste it.

Even if you do not smell exhaust fumes, you could still be

exposed to carbon monoxide gas.

•

Extension cords running directly into the home increase

your risk of carbon monoxide poisoning through openings.

• If an extension cord running directly into the home is

used to power indoor items, the operator recognizes that

this increases the risk of CO poisoning to people inside

the home and assumes that risk.

Install a manual transfer switch as soon as possible

if generator will be used to provide home power

restoration.

5 Volt DC USB Ports

The combined maximum current available for the USB

ports is 2.1 Amps at 5 Volts. The USB port allows you to

recharge most USB powered devices with a USB charging

cable (not included).

NOTICE For maximum output, use the bottom USB port.

NOTICE For charging ITE (Information Technology

Equipment) only.

12 Volt DC Receptacle

The maximum current available for the 12 Volt DC

receptacle is 5 Amps. A DC circuit breaker protects this

receptacle from overloads. If an overload occurs, the circuit

breaker will trip (push button pops out). Wait a few minutes

and push the button in to reset the circuit breaker.

230 Volt AC, 15 Amp Receptacles

These receptacles are protected against overload by an

internal overload system.

Use receptacles to operate 230 Volt AC, single–phase, 50

Hz electrical loads requiring up to 2,800 watts (2.8 kW)

at 12.2 Amps of current. Use cord sets that are rated for

230 Volt AC loads at 15 Amps (or greater).

Output Indicator

The green LED output indicator light comes on when

the generator is operating normally. It indicates that the

generator is producing power at the receptacles.

Overload Alarm

The red LED overload alarm light comes on and cuts

power to the receptacles if you overload the generator. The

green output indicator light will also go off. If the generator

was overloaded, you must turn off and unplug all electrical

loads, press the “Reset” button on the generator control

panel and then plug in and restart electrical loads one at a

time to continue in normal operating mode.

Parallel Operation

Two Briggs & Stratton inverter generators can be run

in parallel with a Briggs & Stratton parallel operation kit

(optional equipment). When running in parallel, the total

output of power is shown in chart.

Models Maximum Output

P2400 & P2400 3300 Watts

P2400 & P3400 4200 Watts

P3400 & P3400 5100 Watts

NOTICE Total electrical load connected to the parallel kit

must not exceed the maximum output.

See the parallel operation kits instruction sheet for detailed

instructions on installation and operation of the connected

generators.

NOTICE

• Turn electrical loads OFF and disconnect from both

generators.

• The QPT switch must be in the same position on both

generators.

• Connect the parallel cables to both generators before

starting the engines. See instruction sheet supplied

with parallel kit.

• Start engine on one of the inverter generators

according to Generator Start Up.

• Once the green LED output indicator light on the first

generators is steady, start second generator.

• Connect and turn on electrical loads to the parallel

panel receptacles.

• DO NOT disconnect parallel cables after engines have

been started.

• Shut down engines as described in Generator

Shutdown.



This feature is designed to greatly improve fuel economy.

When QPT is on, engine speed increases as loads are

connected, and decreases as loads are removed.

When QPT is off, engine will run at full governed speed.

Not for

Reproduction

10 BRIGGSandSTRATTON.com.au

Operation

STATSTATION™

The control panel has a built in LCD display to monitor the

following features:

• Load Monitor (Total Generator Load)

• Hour Meter (Total Generator Hours)

• Maintenance Reminder (Engine Maintenance)

Load Monitor

The load monitor measures the output wattage (generator

load) of all the generator receptacles and will display the

percentage of total generator load.

Hour Meter

The LCD on the control panel also has a built in hour meter

that displays and records how many hours your generator

has run (up to 999.9).

Maintenance Reminder

The LCD on the control panel also has a built in

maintenance reminder to alert you to change air filter,

change oil, and change spark plug. The LCD display will

flash both the load percentage and the hour display every

50 hours for the different maintenance intervals. See

Maintenance Schedule for different maintenance intervals.

Pressing the “View” button will toggle between the flashing

load percentage and the flashing hour display. Once

maintenance has been performed, you must push and hold

the “View” button on the control panel for a minimum of

3 seconds to stop the display from flashing and return it to

normal operation.

Generator Capacity

To make sure your generator can supply enough running

watts and starting watts for the items you will power at the

same time, follow these three simple steps:

1. Select the items you will power at the same time. See

following list for typical wattages.

* Typical wattages listed are approximate only. Check tool

or appliance for actual wattage.

** The momentary electrical current the generator can

provide to start electric motors, per Briggs & Stratton

standard 628K. It does not represent the power required to

continuously run electrical loads. It is the maximum current

that can momentarily be supplied when starting a motor,

multiplied by the generator’s rated voltage.

2. Total the running watts. This is the amount of power

your generator must produce to keep your items

running. See following example:

Example

Total running watts = 2125

Highest starting watts = 2100

Total generator watts required = 4225

3. Estimate the starting watts you will need. Because not

all motors start at the same time, total starting wattage

can be estimated by adding only the item with the

highest additional starting watts requirements to the

total running watts from step 2.

Tool or Appliance Running Watts Starting Watts

Window AC - 10000 BTU

1000 2100

Refrigerator/Freezer 550 1350

Plasma Television 500 —

Light (75 Watts) 75 —

2125 Total

Running Watts

2100 Highest

Starting Watts

Tool or Appliance

Running

Watts*

Starting

Watts**

Light Bulb - 75 Watt 75 -

Refrigerator/Freezer 550 1350

Window AC - 10,000 BTU 1000 2100

Microwave Oven - 1000 Watt 1000 -

Plasma Television - 50” 500 -

Laptop 250 -

LCD display

View button

Reset button

Not for

Reproduction

Maintenance

Power Management

To manage generator power, sequentially add loads as

follows:

1. With nothing connected to generator, start the engine

outdoors.

2. Plug in and turn on the first load, preferably the largest

load you have.

3. Permit the generator output to stabilize (engine runs

smoothly and attached device operates properly).

4. Plug in and turn on the next load.

5. Again, permit the generator to stabilize.

6. Repeat steps 4 and 5 for each additional load.

Never add more loads than the generator capacity. Take

special care to consider starting watts in generator capacity.

Carbon Monoxide (CO) Shutdown System

Automatically shuts down the engine when harmful levels

of carbon monoxide accumulate around the generator or

a CO shutdown system fault occurs. After shutdown, the

indicator light will blink for at least five minutes per the

chart below.

he CO shutdown system DOES NOT replace carbon

monoxide alarms. Install battery-powered carbon monoxide

alarm(s) in your home. Do not run generator in enclosed

areas.

Color/Pattern Description

Red

•• ••

Carbon monoxide accumulated around

generator. Move generator to an

open, outdoor area 6.1 m (20 ft.) from

occupied spaces with exhaust pointed

away. Automatic shutoff is an indication

generator was improperly located. Air

out premises (e.g. open windows and

doors) before reoccupying.

If you start to feel sick, dizzy, weak, or

your homes carbon monoxide alarm

sounds while using this product, get

to fresh air right away. Call emergency

services. You may have carbon

monoxide poisoning.

Blue

• • •

CO shutdown system fault occured*.

See Briggs & Stratton authorized service

dealer.

*Blue light will blink for five seconds at the startup of generator to

show the CO shutdown system is functioning properly.

Step 5: Generator Shutdown

1. Turn off and unplug all electrical loads from generator

panel receptacles. Never stop engine with electrical

devices plugged in and turned on.

2. Let engine run at no-load for one minute to stabilize

internal temperatures of engine and generator.

3. Turn engine switch to the off position.

Maintenance

Maintenance Schedule

Follow the hourly or calendar intervals, whichever occurs

first. More frequent service is required when operating in

adverse conditions noted below.

Service more often under dirty or dusty conditions.

See any authorized dealer for service.

General Recommendations

Regular maintenance will improve the performance and

extend the life of the generator. See any Briggs & Stratton

Authorized Service Dealer for maintenance and service.

The generator’s warranty does not cover items that have

been subjected to operator abuse or negligence. To receive

full value from the warranty, the operator must maintain the

generator as instructed in this manual.

All service and adjustments should be made at least once

each season. A new spark plug and clean air filter assure

proper fuel-air mixture and help your engine run better and

last longer. Follow requirements in Maintenance Schedule.

Emissions Control

Maintenance, replacement, or repair of the emissions

control devices and systems may be performed by any

non-road engine repair establishment or individual.

However, to obtain ”no charge” emissions control service,

the work must be performed by a factory authorized dealer.

See Emissions Warranty.

The emissions control system for carbureted engines is

EM (Engine Modifications). The emissions control systems

for engines with electronic fuel injection are ECM (Engine

Control Module), MPI (Multi Port Injection), and if equipped

an O2S (Oxygen Sensor).

• Generator is equipped with a G-trim engine.

Every 8 Hours or Daily

• Clean debris

• Check engine oil level

First Month or 10 Hours

• Change engine oil

Every 50 Hours or 3 Months

• Clean engine air cleaner

Every 100 Hours or 6 Months

• Change engine oil

• Service spark plug

• Inspect muffler and spark arrester

1, 2

• Clean fuel sediment cup

Not for

Reproduction

12 BRIGGSandSTRATTON.com.au

Maintenance

Cleaning

Daily or before use, look around and underneath the

generator for signs of oil or fuel leaks. Clean any accumulated

debris. Keep area around muffler free from any debris.

• Use a soft bristle brush to loosen caked on dirt or oil.

• Use a damp cloth to wipe exterior surfaces clean.

NOTICE Improper treatment of generator could damage

it and shorten its life. Do not expose generator to excessive

moisture, dust, dirt, or corrosive vapors. Do not insert any

objects through cooling slots.

Engine Maintenance

Oil Recommendations

We recommend the use of Briggs & Stratton Warranty

Certified oils for best performance. Other high-quality

detergent oils are acceptable if classified for service SF,

SG, SH, SJ or higher. Do not use special additives.

Outdoor temperatures determine the proper oil viscosity

for the engine. Use the chart to select the best viscosity for

the outdoor temperature range expected. Engines on most

outdoor power equipment operate well with 5W30 Synthetic

oil. For equipment operated in hot temperatures, Vanguard®

15W50 Synthetic oil provides the best protection.

* Below 4°C (40°F) the use of SAE 30 will result in hard starting.

** Above 27°C (80°F) the use of 10W30 may cause increased oil

consumption. Check oil level more frequently.

Checking/Adding Engine Oil

Oil level should be checked prior to each use or at least

every 8 hours of operation. Keep oil level maintained.

1. Make sure generator is on a level surface.

2. Loosen the two maintenance cover screws and

remove the side maintenance cover.

3. Clean area around oil fill, remove oil fill cap and check

oil level.

4. If needed, slowly pour oil into oil fill opening to the

point of overflowing.

5. Replace and tighten oil fill cap.

NOTICE Do not attempt to crank or start engine before

it has been properly serviced with recommended oil. This

could result in an engine failure.

6. Reinstall the side maintenance cover and hand

tighten the cover screws.

CAUTION Avoid prolonged or repeated skin contact with

used motor oil. Used motor oil has been shown to cause

skin cancer in certain laboratory animals. Thoroughly wash

exposed areas with soap and water.

KEEP OUT OF REACH OF CHILDREN. DON’T

POLLUTE. CONSERVE RESOURCES. RETURN

USED OIL TO COLLECTION CENTERS.

Changing Engine Oil

If you are using your generator under extremely dirty or

dusty conditions, or in extremely hot weather, change the

oil more often.

Change the oil while the engine is still warm from running,

as follows:

1. Make sure unit is on a level surface.

2. Drain fuel tank by running generator until fuel tank is

empty.

3. Remove cover over the oil fill area.

4. Clean area around oil fill and remove oil fill cap.

5. Tip your generator to drain oil from oil fill into a

suitable container making sure you tip your unit toward

the oil filler neck. When crankcase is empty, return

generator to upright position.

6. Using an oil funnel, slowly pour recommended oil

(about 0.4 l (13.5 oz.)) into oil fill opening. Checking oil

level frequently, fill to point of overflowing.

NOTICE Pause to permit oil to settle. DO NOT overfill.

7. Replace and tighten oil fill cap.

8. Wipe up any spilled oil.

9. Replace cover over oil fill area.

Not for

Reproduction

Maintenance

Service Air Cleaner

WARNING! Fuel and its vapors are extremely

flammable which could cause burns or fire

resulting in death or serious injury.

• Do not start and run engine with air filter removed.

Your engine will not run properly and may be damaged

if you run it with a dirty air cleaner. Service more often if

operating under dirty or dusty conditions.

1. Loosen the side maintenance cover screws and

remove the side maintenance cover.

2. Loosen air cleaner cover screw (A) and remove air

cleaner cover (B).

3. Carefully remove foam air cleaner (C) by pulling it out

towards you.

4. Carefully remove pre-filter (D) by pulling it out towards

you.

5. Wash foam air cleaner and breather filter in liquid

detergent and water only. Squeeze dry in a clean

cloth.

6. SATURATE foam air cleaner in clean engine oil and

squeeze in a clean cloth to remove excess oil.

7. Reinstall clean or new foam air cleaner inside base.

8. Reinstall clean or new breather filter inside base.

9. Reinstall the air cleaner cover and tighten screw.

10. Reinstall the side maintenance cover and hand tighten

the cover screws.

Service Spark Plug

Changing the spark plug will help your engine to start

easier and run better.

1. Push in on tab with screwdriver and remove top

maintenance cover.

2. Clean area around spark plug and remove spark plug

boot.

Remove spark plug and inspect spark plug.

4. Replace spark plug if electrodes are pitted, burned

or porcelain is cracked. Use the recommended

replacement spark plug. See Common Service Parts.

5. Check electrode gap with wire feeler gauge and reset

spark plug gap to recommended gap if necessary

(see Specifications).

6. Install spark plug and tighten firmly. Reinstall spark

plug boot.

7. Reinstall top maintenance cover.

Not for

Reproduction

14 BRIGGSandSTRATTON.com.au

Maintenance/Storage

Inspect Muffler and Spark Arrester

The engine exhaust muffler has a spark arrester screen.

Inspect the muffler for cracks, corrosion, or other damage.

Inspect spark arrester screen for damage or carbon

blockage. Clean if carbon blockage is found or replace if

damaged. If replacement parts are required, make sure to

use only original equipment replacement parts.

WARNING! Contact with muffler area could

cause burns resulting in serious injury.

• Do not touch hot parts.

Clean or replace spark arrester as follows:

1. Loosen back cover screws and remove cover.

2. Remove screw that attaches spark arrester screen to

muffler. Remove spark arrester screen.

3. Obtain a replacement screen. See Common Service

Parts.

4. Reattach screen to muffler. Reattach back cover.

Common Service Parts

Air Cleaner ...........................84003886

Spark Plug ...........................84003884

Engine Oil Bottle ........................100028

Synthetic Oil Bottle ......................100074

Spark Arrester ..........................703189

Contact an authorized service dealer or

BRIGGSandSTRATTON.com for a full list of parts and

diagrams.

Storage

If storing the unit for more than 30 days, use the following

guidelines to prepare it for storage.

Long Term Storage Instructions

1. Clean the generator as outlined in Cleaning.

2. Change engine oil while engine is still warm, drain oil

from crankcase. Refill with recommended grade. See

Changing Engine Oil.

3. Treat or drain fuel from generator as fuel can become

stale when stored over 30 days.

Each time you fill the container with fuel, add STA-BIL

360°® PROTECTION™ to the fuel as specified by the

manufacturer’s instructions. This keeps fuel fresh and

decreases fuel-related problems or contamination in the

fuel system.

It is not necessary to drain fuel from the engine when STA-

BIL 360°® PROTECTION™ is added as instructed. Before

storage, turn the engine ON for 2 minutes to move the fuel

and stabilizer through the fuel system.

If fuel in the engine has not been treated with STA-

BIL 360°® PROTECTION™, it must be drained into an

approved container. Then run the engine until it stops from

lack of fuel.

WARNING!

Fuel and its vapors are extremely

flammable and explosive which could cause

burns, fire or explosion resulting in death or

serious injury.

• When storing fuel or equipment with fuel in tank, store

away from furnaces, stoves, water heaters, clothes

dryers or other appliances that have pilot light or other

ignition source because they could ignite fuel vapors.

• When draining fuel, turn generator engine off and let it

cool at least 2 minutes before removing fuel cap. Loosen

cap slowly to relieve pressure in tank. Drain fuel tank

outdoors. Keep fuel away from sparks, open flames, pilot

lights, heat, and other ignition sources.

• Check fuel lines, tank, cap and fittings frequently for

cracks or leaks. Replace if necessary.

4. Turn the engine switch to the off

position.

5. Store generator in clean, dry area and cover with a

suitable protective cover that does not retain moisture.

WARNING! Storage covers could cause a fire

resulting in death or serious injury.

• Do not place a storage cover over a hot or running

generator. Let equipment cool for a sufficient time before

placing the cover on the equipment.

Not for

Reproduction

Troubleshooting/Specifications

Problem Cause Correction

Engine is running, but no AC

output is available.

1. One of the circuit breakers is open.

2. Poor connection or defective cord set.

3. Connected device is bad.

4. Red LED light is steady. Generator is

overloaded or overheated.

1. Reset circuit breaker.

2. Check and repair.

3. Connect another device that is in

good condition.

4. See Generator Capacity. Press

MAIN RESET button on control

panel.

Engine runs well at no-load but

“bogs down” when loads are

connected.

1. Generator is overloaded. 1. See Generator Capacity.

Engine will not start; starts and

runs rough or shuts down when

running.

1. Engine switch is in off

position.

2. Low oil indicator light comes on. Low

oil level.

3. Dirty air cleaner.

4. Out of fuel.

5. Spark plug wire not connected to

spark plug.

6. Flooded with fuel.

1. Turn engine switch to on

position.

2. Fill crankcase to proper level or

place generator on level surface.

3. Clean or replace air cleaner.

4. Fill fuel tank.

5. Connect wire to spark plug.

6. Wait 5 minutes and re-crank engine.

Engine shuts down and CO

shutdown system LED blinks red

(•• ••) .

1. Generator improperly located.

1. Move generator to an open,

outdoor area. Air out premises (e.g.

open windows and doors) before

reoccupying. See Carbon Monoxide

(CO) Shutdown System.

For all other issues, see a Briggs & Stratton authorized dealer.

Specifications

Rated Wattage* ........................................... 2,800

Starting Wattage** ......................................... 3,400

Current at 230 Volts AC .................................12.2 Amps

Current at 12 Volts DC ...................................5.0 Amps

Current at 5 Volts DC ....................................2.1 Amps

Frequency ................................................ 50 Hz

Phase .............................................Single Phase

Displacement ................................ 171 cc (10.44 cu. in.)

Spark Plug Gap ........................0.6-0.7 mm (0.024-0.028 in.)

Fuel Capacity ...........................4.0 Liters (1.0 U.S. Gallons)

Oil Capacity ...............................0.4 Liters (13.5 Ounces)

Sound Pressure @ 7 m§ ...................................78 dBA

* Generator rated in accordance with CSA (Canadian Standards Association) standard C22.2 No. 100-14, Motors and Generators.

** Per Briggs & Stratton 628K.

§ Measured sound values in accordance to AS/NZS 3010:2017 Electrical installations - Generating sets.

Not for

Reproduction

16 BRIGGSandSTRATTON.com.au

Warranty



Warranty service is available only through Briggs & Stratton Authorized Service Dealers. Most warranty repairs are handled routinely, but sometimes requests for

warranty service may not be appropriate. This warranty covers only defects in materials or workmanship. It does not cover damage caused by improper use or

abuse, improper maintenance or repair, normal wear and tear, or stale or unapproved fuel.

Improper Use and Abuse - The proper, intended use of this product is described in the Operator’s Manual. Using the product in a way not described in the

Operator’s Manual or using the product after it has been damaged will not be covered under this warranty. Warranty coverage will also not be provided if the serial

number on the product has been removed or the product has been altered or modified in any way, or if the product has evidence of abuse such as impact damage

or water/chemical corrosion damage.

Improper Maintenance or Repair - This product must be maintained according to the procedures and schedules provided in the Operator’s Manual, and serviced

or repaired using genuine Briggs & Stratton parts or equivalent. Damage caused by lack of maintenance or use of non-original parts is not covered by warranty.

Normal Wear and Tear - Like most mechanical devices, your unit is subject to wear even when properly maintained. This warranty does not cover repairs when

normal use has exhausted the life of a part or the equipment. Maintenance and wear items such as filters, belts, cutting blades, and brake pads (except engine

brake pads) are not covered by warranty due to wear characteristics alone, unless the cause is due to defects in material or workmanship.

Stale or Unapproved Fuel - In order to function correctly, this product requires fresh fuel that conforms to the criteria specified in the Operator’s Manual. Engine or

equipment damage caused by stale fuel or the use of unapproved fuels (such as E15 or E85 ethanol blends) is not covered by warranty.

Other Exclusions - This warranty excludes damage due to accident, abuse, modifications, alterations, improper servicing, freezing or chemical deterioration.

Attachments or accessories that were not originally packaged with the product are also excluded. There is no warranty coverage on equipment used for

primary power in place of utility power or on equipment used in life support applications. This warranty does not include used, reconditioned, second-hand, or

demonstration equipment or engines. This warranty also excludes failures due to acts of God and other force majeure events beyond the manufacturer’s control.





** In Australia - Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a

major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods

fail to be of acceptable quality and the failure does not amount to a major failure. For warranty service, find the nearest Authorized Service Dealer in our dealer

locator map at BRIGGSandSTRATTON.COM, or by calling 1300 274 447, or by emailing or writing to [email protected], Briggs & Stratton

Australia Pty Ltd, 1 Moorebank Avenue, NSW, Australia, 2170.

The warranty period begins on the date of purchase by the first retail or commercial consumer. “Consumer use” means personal residential household use by a

retail consumer. “Commercial use” means all other uses, including use for commercial, income producing or rental purposes. Once a product has experienced

commercial use, it shall thereafter be considered as a commercial use product for purposes of this warranty.

Save your proof of purchase receipt. If you do not provide proof of the initial purchase date at the time warranty service is requested, the manufacturing date of the

product will be used to determine the warranty period. Product registration is not required to obtain warranty service on Briggs & Stratton products.

Limited Warranty

Briggs & Stratton warrants that, during the warranty period specified below, it will repair or replace, free of charge, any part that is defective in material or

workmanship or both. Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is

effective for and is subject to the time periods and conditions stated below. For warranty service, find the nearest Authorized Service Dealer in our dealer locator

map at www.briggsandstratton.com. The purchaser must contact the Authorized Service Dealer, and then make the product available to the Authorized Service

Dealer for inspection and testing.

There is no other express warranty. Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to the

warranty period listed below, or to the extent permitted by law. Liability for incidental or consequential damages are excluded to the extent exclusion is

permitted by law. Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not allow the exclusion

or limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you specific legal rights and

you may also have other rights which vary from state to state or country to country.**

Consumer Use Commercial Use

36 months  12 months



80088366EN (Rev. A)