Broan JS6BD-K Installation guide

JS6BD-K
Broan
Brand
Broan
Model
JS6BD-K
Category
Split-system air conditioners
Type
Installation guide
Please read this information thoroughly and become familiar with the capabilities and
use of your appliance before attempting to operate or maintain this unit. Keep this
literature where you have easy access to it in the future. If a problem occurs, check the
instructions and follow recommendations given. If these suggestions don’t eliminate
your problem, call your servicing contractor.
The Installation Instructions are primarily intended to assist qualifi ed individuals
experienced in the proper installation of this appliance. Some local codes require licensed
installation/service personnel for this type of equipment. Please read all instructions
carefully before starting the installation.
DO NOT DESTROY. PLEASE READ CAREFULLY AND
KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.
IMPORTANT
SPLIT SYSTEM AIR CONDITIONER
USER’S MANUAL / INSTALLATION INSTRUCTIONS
JS6BD SERIES 13 SEER
2
Important Safety Information ....................................4
Air Conditioner Installation .......................................5
General Information ...................................................5
Before You Install this Unit .........................................5
Locating the Air conditioner .......................................5
Packaging Removal ...................................................5
Ground Level .............................................................5
Connecting Refrigerant Tubing Between the
Indoor & Outdoor Unit ...............................................6
Electrical Wiring ..........................................................6
Pre - Electrical Checklist ...........................................6
Line Voltage ...............................................................6
Grounding..................................................................7
Thermostat Connections ...........................................7
Startup & Adjustments ..............................................8
Pre - Start Checklist ..................................................8
Start-up Procedures ..................................................8
Air Circulation - Indoor Blower ...............................8
System Cooling ......................................................8
System Heating ......................................................8
Refrigerant Charging .................................................8
Charging R-410A Units in AC Mode with
Outdoor Temperatures Above 55° F .......................8
Air Conditioner Maintenance .....................................9
Component Functions ...............................................9
Replacement Parts .....................................................9
Figures & Tables ....................................................... 10
Table 3. Unit Dimensions ...................................... 10
Table 4. Electrical Specs & Physical Data ............ 11
Figure 4. Wiring Diagram - 2 & 2.5 Ton Units ....... 12
Figure 5. Wiring Diagram - 3 Ton Units ................ 13
Figure 6. Wiring Diagram - 3.5 - 5 Ton Units ........ 14
Cooling Charging Charts ......................................... 15
Figure 7. Charging Chart for 2 Ton Units .............. 16
Figure 8. Charging Chart for 2.5 Ton Units ........... 16
Figure 9. Charging Chart for 3 Ton Units .............. 17
Figure 10. Charging Chart for 3.5 Ton Units ......... 17
Figure 11. Charging Chart for 4 Ton Units ............ 18
Figure 12. Charging Chart for 5 Ton Units ............ 18
INSTALLATION / PERFORMANCE CHECKLIST ..... 20
USER INFORMATION
INSTALLER INFORMATION
Important Safety Information ....................................3
Operating Instructions ...............................................3
Cooling Operation .....................................................3
Heating Operation .....................................................3
Operating the Air Conditioner for Automatic
Cooling and Heating ..................................................3
Operating the Indoor Blower Continuously ................3
Turning the Air Conditioner Off ..................................3
Air Conditioner Maintenance .................................... 3
Troubleshooting ......................................................... 3
WARRANTY INFORMATION
A warranty certifi cate with full details is included with the
air conditioner. Carefully review these responsibilities with
your dealer or service company. The manufacturer will not
be responsible for any costs found necessary to correct
problems due to improper setup, improper installation,
adjustments, improper operating procedure on the part
of the user, etc. Some specifi c examples of service calls
which are not included in the limited warranty are:
• Correcting wiring problems in the electrical circuit
supplying the air conditioner.
• Resetting circuit breakers or other switches.
• Adjusting or calibrating of thermostat.
3
IMPORTANT SAFETY INFORMATION
Safety markings are used frequently throughout this
manual to designate a degree or level of seriousness and
should not be ignored. WARNING indicates a potentially
hazardous situation that if not avoided, could result in
personal injury or death. CAUTION indicates a potentially
hazardous situation that if not avoided, may result in minor
or moderate injury or property damage.
USER INFORMATION
OPERATING INSTRUCTIONS
NOTE: Thermostat styles vary. Some models may not
include the AUTO mode and others will have the AUTO
in place of the HEAT and COOL. Others may include all
three. Please refer to the thermostat manufacturer’s User
manual for detailed programming instructions.
Cooling Operation
1. Set the thermostat’s system mode to COOL or AUTO
and change the fan mode to AUTO. See Figure 1.
2. Set the temperature selector to the desired
temperature level. The outdoor fan, compressor, and
blower motor will all cycle on and off to maintain the
indoor temperature at the desired cooling level.
NOTE: If the temperature level is re-adjusted, or the
system mode is reset, the fan and compressor in the
outdoor unit may not start immediately. A protective
timer circuit holds the compressor and the outdoor fan
off for approximately 5 minutes following a previous
operation or the interruption of the main electrical
power (if applicable).
Heating Operation
1. Set the thermostat’s system mode to HEAT or AUTO
and change the fan mode to AUTO. See Figure 1.
2. Set the temperature selector to the desired
temperature level. The optional heating equipment
(furnace or electric heat) will cycle on & off to maintain
the indoor temperature at the desired temperature
level.
The continuous indoor blower operation can be obtained
with the thermostat system mode set in any position,
including OFF.
Turning the Air Conditioner OFF
Change the thermostat’s system mode to OFF and the fan
mode to AUTO (See Figure 1). NOTE: The system will not
operate, regardless of the temperature selector setting.
Figure 1. Digital Thermostat
Fan
Mode
Temperature
Selector
System
Mode
AIR CONDITIONER MAINTENANCE
Proper maintenance is most important to achieve the best
performance from the appliance and should be performed
frequently at the beginning of each air conditioning season.
WARNING:
Your Air Conditioner contains liquid and gaseous
refrigerant under pressure. Installation and
servicing should only be attempted by qualifi ed,
trained personnel thoroughly familiar with the
equipment and safe responsible refrigerant
handling procedures. Failure to comply with
this warning could result in equipment damage,
personal injury, or death.
• Keep the outdoor unit clean. Hose off periodically and
keep unit fi ns clear of leaves and grass clippings.
• Keep the outdoor unit clear of obstructions.
DO NOT obstruct airfl ow with tall plants or shrubs.
DO NOT store gasoline or other fl ammable materials
on or near the outdoor unit.
• Never operate the appliance without a fi lter installed in
the return air duct. Inspect fi lters frequently and replace
when necessary with fi lter of same dimensional size.
TROUBLESHOOTING
• Check the thermostat setting. Make sure the system
mode and temperature settings are correct.
• Check the electrical panel for tripped circuit breakers.
• Check the fi lters for dust accumulation.
• Check the outdoor unit and make sure it is clean and
not covered with grass or leaves.
Operating the AC for Automatic Cooling & Heating
1. Set the thermostat system mode to AUTO and the
thermostat fan mode to AUTO. See Figure 1.
2. Set the thermostat temperature selector to the desired
temperature level. The thermostat will maintain the
desired temperature level by switching between either
the outdoor cooling unit or the indoor heating unit
(furnace or electric heat) automatically.
Operating the Indoor Blower Continuously
The continuous indoor blower operation is typically used to
circulate the indoor air to equalize a temperature unbalance
due to a sun load, cooking, or fi replace operation.
Set the
thermostat fan mode to ON (Figure 1). The indoor blower
starts immediately, and will run continually until the fan
mode is reset to AUTO.
4
INSTALLER INFORMATION
IMPORTANT SAFETY INFORMATION
INSTALLER: Please read all instructions before servicing
this equipment. Pay attention to all safety warnings and
any other special notes highlighted in the manual. Safety
markings are used frequently throughout this manual to
designate a degree or level of seriousness and should not
be ignored. WARNING indicates a potentially hazardous
situation that if not avoided, could result in personal injury
or death. CAUTION indicates a potentially hazardous
situation that if not avoided, may result in minor or moderate
injury or property damage.
WARNING:
Shut off all electrical power to the unit before
performing any maintenance or service on the
system. Failure to comply may result in personal
injury or death.
WARNING:
Unless noted otherwise in these instructions,
only factory authorized parts or accessory
kits may be used with this product. Improper
installation, service, adjustment, or maintenance
may cause explosion, fi re, electrical shock or
other hazardous conditions which may result in
personal injury or property damage
WARNING:
JS6BD Split System Air conditioners leave
the factory with an R-410A refrigerant holding
charge. Follow all charging instructions for
maximum unit performance and effi ciency. Some
local codes require licensed installation/service
personnel to service this type of equipment.
Refrigerant charging must be done by qualifi ed
personnel familiar with safe and environmentally
responsible refrigerant handling procedures.
Under no circumstances should the owner
attempt to install and/or service this equipment.
Failure to comply with this warning could result
in property damage, personal injury, or death.
CAUTION:
This unit uses refrigerant R-410A. DO NOT use
any other refrigerant in this unit. Use of another
refrigerant will damage the unit.
WARNING:
The information listed below must be followed
during the installation, service, and operation
of this unit. Unqualifi ed individuals should
not attempt to interpret these instructions or
install this equipment. Failure to follow safety
recommendations could result in possible
damage to the equipment, serious per
sonal
injury or death
.
• The installer must comply with all local codes and
regulations which govern the installation of this type
of equipment. Local codes and regulations take
precedence over any recommendations contained in
these instructions. Consult local building codes and
the National Electrical Code (ANSI CI) for special
installation requirements.
• All electrical wiring must be completed in accordance
with local, state and national codes and regulations
and with the National Electric Code (ANSI/NFPA 70)
or in Canada the Canadian Electric Code Part 1 CSA
C.22.1.
• This equipment contains liquid and gaseous refrigerant
under high pressure. DO NOT USE ANY PORTION OF
THE CHARGE FOR PURGING OR LEAK TESTING.
Installation or servicing should only be performed by
qualifi ed trained personnel thoroughly familiar with this
type equipment.
• Fully annealed, refrigerant grade copper tubing should
be used when installing the system. Refrigerant suction
line tubing should be fully insulated.
• Installation of equipment may require brazing
operations. Installer must comply with safety codes
and wear appropriate safety equipment (safety glasses,
work gloves, fi re extinguisher, etc.) when performing
brazing operations.
• Follow all precautions in the literature, on tags, and
on labels provided with the equipment. Read and
thoroughly understand the instructions provided with
the equipment prior to performing the installation and
operational checkout of the equipment.
5
AIR CONDITIONER INSTALLATION
General Information
The JS6BD series air conditioner is designed only for
outdoor rooftop or ground level installations. This unit has
been tested for capacity and effi ciency in accordance with
A.H.R.I. Standards and will provide many years of safe
and dependable comfort, providing it is properly installed
and maintained. Abuse, improper use, and/or improper
maintenance can shorten the life of the appliance and
create unsafe hazards.
To achieve optimum performance and minimize equipment
failure, it is recommended that periodic maintenance be
performed on this unit. The ability to properly perform
maintenance on this equipment requires certain
mechanical skills and tools.
Before You Install this Unit
The cooling load of the area to be conditioned must be
calculated and a system of the proper capacity selected.
It is recommended that the area to be conditioned be
completely insulated and vapor sealed.
Check the electrical supply and verify the power supply
is adequate for unit operation. The system must be wired
and provided with circuit protection in accordance with
local building codes. If there is any question concerning
the power supply, contact the local power company.
The indoor section (air handler, furnace, etc) should be
installed before routing the refrigerant tubing. Refer to
the indoor unit's installation instructions for installation
details.
All units are securely packed at the time of shipment and
upon arrival should be carefully inspected for damage
prior to installing the equipment at the job site. Verify
coil fi ns are straight. If necessary, comb fi ns to remove
fl attened or bent fi ns. Claims for damage (apparent or
concealed) should be fi led immediately with the carrier.
Please consult your dealer for maintenance information
and availability of maintenance contracts. Please read
all instructions before installing the unit.
18"
18"
18"
18"
DO NOT
OBSTRUCT
TOP OF UNIT
Figure 2. Clearance Requirements
Locating the Air Conditioner
• Survey the job site to determine the best location for
mounting the outdoor unit. See Table 3 (page 10) for
unit dimensions.
• Overhead obstructions, poorly ventilated areas, and
areas subject to accumulation of debris should be
avoided.
• Suffi cient clearance for unobstructed airfl ow through the
outdoor coil must be maintained in order to achieve rated
performance. See Figure 2 for minimum clearances to
obstructions.
• Consideration should be given to availability of electric
power, service access, noise, and shade.
Packaging Removal
NOTE: To prevent damage to the tubing connections,
carefully remove the carton and user’s manual from the
equipment. Discard the shipping carton.
Ground Level
Ground level installations must be located according to
local building codes or ordinances and these requirements:
• Clearances must be in accordance with those shown
in Figure 2.
• A suitable mounting pad (Figure 3) must be provided
and separate from the building foundation. The pad
must be level and strong enough to support the weight
of the unit. The slab height must be a minimum of 2”
(5 cm) above grade and with adequate drainage.
2”
Figure 3. Ground Level Installation
6
Connecting Refrigerant Tubing Between the Indoor
& Outdoor Unit
CAUTION:
This system uses R-410A refrigerant with POE
oil. When servicing, cover or seal openings to
minimize the exposure of the refrigerant system
to air to prevent accumulation of moisture and
other contaminants.
After outdoor and indoor unit placement has been
determined, route refrigerant tubing between the
equipment in accordance with sound installation practices.
• When connecting refrigerant linesets together, it is
recommended that dry nitrogen be fl owing through
the joints during brazing to prevent internal oxidation
and scaling.
• Refrigerant tubing should be routed in a manner that
minimizes the length of tubing and the number of bends
in the tubing. If precise forming of refrigerant lines is
required, a copper tubing bender is recommended.
Avoid sharp bends and contact of the refrigerant lines
with metal surfaces.
• Refrigerant tubing should be supported in a manner
that the tubing will not vibrate or abrade during system
operation.
• Tubing should be kept clean of foreign debris during
installation.
• Every effort should be made by the installer to ensure
that the fi eld installed refrigerant containing components
of the system have been installed in accordance with
these instructions and sound installation practices to
insure reliable system operation and longevity.
• The maximum recommended interconnecting
refrigerant line lengths is 75 ft. and the vertical elevation
difference between the indoor and outdoor sections
should not exceed 20 ft.
• A fi lter dryer is provided with the unit and must be
installed in the liquid line of the system. If the installation
replaces a system with a fi lter dryer already present
in the liquid line, the fi lter dryer must be replaced with
the one supplied with the unit. The fi lter dryer must be
installed in strict accordance with the manufacturer’s
installation instructions.
• Optional equipment such as liquid line solenoid
valves, low ambient, etc., should be installed in
strict accordance with the manufacturer’s installation
instructions.
ELECTRICAL WIRING
WARNING:
To avoid risk of electrical shock, personal injury,
or death, disconnect all electrical power to the unit
before performing any maintenance or service.
The unit may have more than one electrical
supply.
Label all wires prior to disconnection when
servicing the unit. Wiring errors can cause
improper and dangerous operation.
• All electrical connections must be in compliance with
all applicable local codes and ordinances, and with
the current revision of the National Electric Code
(ANSI/NFPA 70).
• For Canadian installations the electrical connections
and grounding shall comply with the current Canadian
Electrical Code (CSA C22.1 and/or local codes).
Pre-Electrical Checklist:
Verify that the voltage, frequency, and phase of the
supply source match the specifi cations on the unit
rating plate. See Table 4 (page 11).
Verify that the service provided by the utility is suffi cient
to handle the additional load imposed by this equipment.
Refer to the unit wiring label for proper voltage wiring.
Verify factory wiring is in accordance with the unit
wiring diagram (Figures 4 - 6, pages 12 - 14). Inspect
for loose connections.
Line Voltage
• A wiring diagram is located on the inside cover of the
electrical box of the outdoor unit. The installer should
become familiar with the wiring diagram before making
any electrical connections to the outdoor unit.
• An electrical disconnect must be located within
sight of and readily accessible to the unit. This
switch shall be capable of electrically de-energizing
the outdoor unit.
• Line voltage to the unit should be supplied from a
dedicated branch circuit containing the correct fuse
or circuit breaker for the unit. Incoming fi eld wiring
and minimum size of electrical conductors and circuit
protection must be in compliance with information listed
on the outdoor unit data label. Any other wiring methods
must be acceptable to authority having jurisdiction.
• The outdoor unit requires both power and control circuit
electrical connections. Refer to the wiring diagram /
schematic for identifi cation and location of outdoor unit
fi eld wiring interfaces (Figures 4 - 6, pages 12 - 14).
Make all electrical connections in accordance with all
applicable codes and ordinances.
• Overcurrent protection must be provided at the branch
circuit distribution panel and sized as shown on the unit
7
COPPER WIRE SIZE — AWG
(1% Voltage Drop)
Supply Wire Length-Feet
Supply Circuit
Ampacity
200 150 100 50
6 8 10 14 15
46812 20
46810 25
44610 30
3468 35
3468 40
2346 45
2346 50
2346 55
1234 60
Wire Size based on N.E.C. for 60° type copper conductors.
Table 1. Copper Wire Size
rating label and according to applicable local codes.
See the unit rating plate for minimum circuit ampacity
and maximum overcurrent protection limits.
• Provide power supply for the unit in accordance with the
unit wiring diagram, and the unit rating plate. Connect
the line-voltage leads to the terminals on the contactor
inside the control compartment.
• Use only copper wire for the line voltage power supply
to this unit as listed in Table 1. Use proper code agency
listed conduit and a conduit connector for connecting
the supply wires to the unit. Use of rain tight conduit
is recommended.
• 208/230 Volt units are shipped from the factory wired
for 230 volt operation. For 208V operation, remove the
lead from the transformer terminal marked 240V and
connect it to the terminal marked 208V.
• Optional equipment requiring connection to the power
or control circuits must be wired in strict accordance
of the NEC (ANSI/NFPA 70), applicable local codes,
and the instructions provided with the equipment.
Thermostat Connections
• Thermostat connections should be made in accordance
with the instructions supplied with the thermostat and
the indoor equipment.
• The outdoor unit is designed to operate from a 24 VAC
Class II control circuit. The control circuit wiring must
comply with the current provisions of the NEC (ANSI/
NFPA 70) and with applicable local codes having
jurisdiction.
• The low voltage wires must be properly connected to
the units low voltage terminal block. Recommended
wire gauge and wire lengths for typical thermostat
connections are listed in Table 2.
• The thermostat should be mounted about 5 feet
above the fl oor on an inside wall. DO NOT install the
thermostat on an outside wall or any other location
where its operation may be adversely affected by radiant
heat from fi replaces, sunlight, or lighting fi xtures, and
convective heat from warm air registers or electrical
appliances. Refer to the thermostat manufacturer’s
instruction sheet for detailed mounting and installation
information.
Table 2. Thermostat Wire Gauge
Thermostat
Wire Gauge
Recommended T-Stat Wire
Unit to T-Stat (Length in FT)
2-Wire
(Heating)
5-Wire
(Heating/Cooling)
24 55 25
22 90 45
20 140 70
18 225 110
Grounding
WARNING:
The unit cabinet must have an uninterrupted or
unbroken electrical ground to minimize personal
injury if an electrical fault should occur. Do not
use gas piping as an electrical ground
!
This unit must be electrically grounded in accordance
with local codes or, in the absence of local codes, with
the National Electrical Code (ANSI/NFPA 70) or the CSA
C22.1 Electrical Code. Use the grounding lug provided in
the control box for grounding the unit.
8
START UP & ADJUSTMENTS
Pre-Start Check List
Verify the indoor unit is level and allows proper
condensate drainage.
Verify the outdoor coil and top of the unit are free from
obstructions and debris, and all equipment access/
control panels are in place.
Verify air fi lters are cleaned and properly installed.
Verify duct work is sealed to prevent air leakage.
Verify line voltage power leads are securely connected
and the unit is properly grounded.
Verify low voltage wires are securely connected to the
correct leads on the low voltage terminal strip.
Verify power supply branch circuit overcurrent protection
is sized properly.
Verify the thermostat is wired correctly.
Start-Up Procedures
The thermostat's function mode should be set to OFF and
the fan mode should be set to AUTO. Close all electrical
disconnects to energize the system.
Air Circulation - Indoor Blower
1. Set the thermostat system mode on OFF and the fan
mode to ON.
2. Verify the blower runs continuously. Check the air
delivery at the supply registers and adjust register
openings for balanced air distribution. If insuffi cient
air is detected, examine ductwork for leaks or
obstructions.
3. Set the thermostat fan mode to AUTO and verify the
blower stops running.
System Cooling
1. Set the thermostat’s system mode to COOL and the
fan mode to AUTO. Gradually lower the thermostat
temperature setpoint below room temperature and
verify the outdoor unit and indoor blower energize.
2. Verify blower wheel is spinning in direction indicated
by arrow. Feel the air being circulated by the indoor
blower and verify that it is cooler than ambient
temperature. Listen for any unusual noises. If unusual
sounds occur, determine the source of the noise and
correct as necessary.
3. Verify HI and LO refrigerant pressures.
4. Allow the system to operate for several minutes
and then set the temperature selector above room
temperature. Verify the fan and compressor cycle off
with the thermostat. NOTE: The blower should also
stop unless fan mode is set to the ON position.
System Heating (optional)
1. Set the thermostat's system mode to HEAT and the
temperature mode above room temperature.
2. Verify the optional heating equipment (furnace or
electric heat) and indoor blower energize. Feel the air
being circulated by the indoor blower and verify that
it is warmer than ambient temperature. Listen for any
unusual noises. If unusual sounds occur, determine
the source of the noise and correct as necessary.
Refrigerant Charging
WARNING:
JS6BD Split System Air Conditioners leave
the factory with an R-410A refrigerant holding
charge. Follow these charging instructions for
maximum unit performance and effi ciency. Some
local codes require licensed installation/service
personnel to service this type of equipment.
Refrigerant charging must be done by qualifi ed
personnel familiar with safe and environmentally
responsible refrigerant handling procedures.
Under no circumstances should the owner
attempt to install and/or service this equipment.
Failure to comply with this warning could result
in property damage, personal injury, or death.
After refrigerant line connections are completed, it is
required that you leak check and evacuate the indoor
section and all line connections (using proper methods)
before fi nalizing the full system refrigerant charge. For
fi nal charges based on matched systems and specifi ed
line lengths, see physical and electrical specifi cations
(Table 4, page 11).
• Refrigerant charging charts are applicable only to
matched assemblies of NORDYNE equipment and
listed airfl ows for the indoor coil. Refer to Figures 7 -
12 (pages 16 - 18) for correct system charging.
• JS6BD outdoor units with indoor coils not listed are
not recommended. Deviations from rated airfl ows or
non-listed combinations may require modifi cation to the
expansion device and refrigerant charging procedures
for proper and effi cient system operation.
• The refrigerant charge can be checked and adjusted
through the service ports provided external to the
outdoor unit. Use only gage line sets which have a
“Schrader” depression device present to actuate the
valve.
Charging an R-410A system in AC mode at outdoor
temperatures above 55° F for optimized sub-cooling of
10° F - 12° F.
1. With the system operating at steady-state, measure
the liquid refrigerant pressure (in psig) at the outdoor
unit service valve.
2. Measure the liquid refrigerant temperature (in
Fahrenheit) at the service valve.
3. Determine the required liquid refrigerant pressure
from the appropriate charging chart (Figures 7 - 12).
• If the pressure measured in Step 1 is greater than
the required liquid refrigerant pressure determined in
Step 3, then there is too much charge in the system.
Remove refrigerant and repeat Steps 1 through 3
until the system is correctly charged.
9
• If the pressure measured in Step 1 is less than the
required liquid refrigerant pressure determined in
Step 3, there is too little charge in the system. Add
refrigerant and repeat Steps 1 through 3 until the
system is correctly charged.
AIR CONDITIONER MAINTENANCE
WARNING:
To prevent electrical shock, personal injury, or
death, disconnect all electrical power to the unit
before performing any maintenance or service.
The unit may have more than one electrical
supply.
Proper maintenance is important to achieve optimum
performance from the air conditioner. The ability to properly
perform maintenance on this equipment requires certain
mechanical skills and tools. If you do not possess these
skills, contact your dealer for maintenance. Consult your
local dealer about the availability of maintenance contracts.
Routine maintenance should include the following:
• Inspect and clean or replace air fi lters at the beginning
of each heating and cooling season, or more frequently
if required.
• Inspect the condensate drain and outdoor coil at the
beginning of each cooling season. Remove any debris.
Clean the outdoor coil and louvers as necessary using
a mild detergent and water. Rinse thoroughly with water.
• Inspect the electrical connections for tightness at the
beginning of each heating and cooling season. Service
as necessary.
CAUTION:
The unit should never be operated without a
fi lter in the return air system. Replace disposable
fi lters with the same type and size.
• Do not attempt to add additional oil to motors
unequipped with oil tubes. The compressor is
hermetically sealed at the factory and does not require
lubrication.
REPLACEMENT PARTS
Replacement parts are available through all Nordyne
distributors.
Please have the complete model and serial number of the unit
when ordering replacement parts.
ELECTRICAL:
Capacitors Temperature Limit Switches
Compressors Thermostats
Contactors Time Delay Relays
Pressure Switches Transformers
Relays
MOTORS:
Blower Motor
Fan Motor
COMPONENTS:
Blower Assembly Fan Grille
Cabinet Panels Filter/Driers
Expansion Valves
COMPONENT FUNCTIONS
High Pressure Switch (HPS)
A high-pressure switch is factory-installed and located in
the liquid line internal to the outdoor unit. The switch is
designed to protect the system when very high pressures
occur during abnormal conditions. Under normal
conditions, the switch is closed. If the liquid pressure
rises above 575 psig, then the switch will open and de-
energize the outdoor unit. The switch will close again
once the liquid pressure decreases to 460 psig. Please
note that the switch interrupts the thermostat inputs to
the unit. Thus, when the switch opens and then closes,
there may be a 5 minute short cycling delay before the
outdoor unit will energize.
10
FIGURES & TABLES
Table 3. Unit Dimensions
Model Number
JS6BD-
Height -H- Width -W- Depth -D-
024 27" 22 3/4" 22 3/4"
030 27" 22 3/4" 22 3/4"
036 35" 22 3/4" 22 3/4"
042 27" 30 3/4" 30 3/4"
048 27" 30 3/4" 30 3/4"
060 31" 30 3/4" 30 3/4"
D
W
H
DO NOT OBSTRUCT TOP OF UNIT
Allow adequate clearance for airflow
11
Table 4. Electrical Specifi cations & Physical Data
Model No. JS6BD 24K 30K 36K 42K 48K 60K
Electrical
Data
Volts-Cycles-Phase 208/230-60-1
Total Amps 11.6 13 18.1 23.5 24.3 30.7
Delay Fuse Max. 20 25 25 35 35 40
Min. Circuit Ampacity 12.9 14.5 20.1 26.2 27.0 34.2
Component
Data
Coil
Area 8.3 8.3 13.3 15.3 15.3 17.8
Rows-FPI 1-22 1-22 1-22 1-16 1-16 1-16
Tube Dia. MC
Fan Motor
Type PSC
Amps 0.7 0.7 1.4 1.4 1.4 1.4
Watts-HP 0.1 0.1 0.25 0.25 0.25 0.25
Fan Blade
Dia. 18” 18” 18” 24” 24” 24”
# Blades 3 3 4 2 2 2
SCFM 2800 3000 3000 3500 3500 3800
Compressor Data
RLA 10.9 12.3 16.7 22.1 22.9 29.3
LRA 49 59 88 115 115 150
Refrigerant Suction Line: Length/O.D.
Liquid Line: All Lengths - 3/8”O.D.
15 - 24 ft. 3/4” 3/4” 3/4” 7/8” 7/8” 7/8”
25 - 39 ft. 3/4” 3/4” 7/8” 7/8” 7/8” 1-1/8”
40 - 75 ft. 3/4” 3/4” 7/8” 7/8” 7/8” 1-1/8”
R-410A Refrigerant Charge (in Ounces):
(Outdoor unit, Indoor Unit - 15’ Line Set)
78 80 89 88 110 115
Approximate Weight (lbs.)
Net 113 116 135 157 163 188
Ship 118 121 140 163 169 194
12
Figure 4. JS6BD Wiring Diagram (2 & 2.5 Ton Units)
7110050
WIRING DIAGRAM
NOTES:
FIELD WIRING
LEGEND:
LOW VOLTAGE
HIGH VOLTAGE
CRANKCASE
HEATER
(OPTIONAL)
3
1
2
START
CAPAC
to”C” on
capacitor
to T2 on
capacitor
to “H” on
capacitor
START
RELAY
Single Phase
1. Couper le courant avant de faire letretien.
2. Employez uniquement des conducteurs
en cuivre.
3. Ne convient pas aux installations
de plus de 150 volt a la terre.
Split System Air Conditioner (Outdoor Section)
1. Disconnect all power before servicing.
2. For supply connections use copper conductors only.
3. Not suitable on systems that exceed 150 volts to ground.
4. For replacement wires use conductors suitable for 105 deg C.
5. For ampacities and overcurrent protection, see unit rating plate..
6. Connect to 24 vac/40ca/class 2 circuit. See furnace/airhandler installation
instructions for control circuit and optional relay/transformer kits.
7. Anti-Shor t Cycle Timer (ASCT) may or may not be installed in the unit. If desired,
ASCT is factory installed on select models only or may be field installed as shown using
manufacturer’s approved kit. If not present, connect Yellow and Black wires per Note 6.
8. DO NOT use a Hard Start Kit on a model with a PTCR installed.
CC - Contac tor Coil
CCH - Crankcase Heater
HPS - High Pressure Switch
208/230V
CC
ASCT
ASCT
(SEE NOTE 7)
H
C
F
CCH
(OPTIONAL)
R
C
S
S
C
R
L2
T2
COMPRESSOR
CONTACTS
L1
T1
PTCR(If equipped)
COMPRESSOR
OUTDOOR FAN
MOTOR
24 VOLT FIELD
CONNECTIONS
HPS
T1
T3
T2
HPS
WIRE NUT
GROUNDING
SCREW
L1 L2
GND
T1
T2
L1
L2
OUTDOOR
FAN MOTOR
C
S
DUAL
CAPACITOR
R
CONTACTOR
C
S
R
H
C
F
ORANGE
BLUE
BLACK
PTCR
BLACK
BLACK
YELLOW/
BLACK
BLACK
RED
BLACK
YELLOW
BLACK
SEE NOTE 6
ASCT
(SEE
NOTE 7)
YELLOW
YELLOW
RED
BLACK
YELLOW
13
Figure 5. JS6BD Wiring Diagram (3 Ton Units)
14
L1
L2
T1
T2
Compressor
Contacts
1. Disconnect all power before servicing.
2. For supply connections use copper conductors only.
3. Not suitable on systems that exceed 150 volts to ground.
4. For replacement wires use conductors suitable for 105˚ C.
5. For ampacities and overcurrent protection, see unit rating plate.
6. Connect to 24 vac/40va/class 2 circuit. See furnace/air handler installation
instructions for control circuit and optional relay/transformer kits.
7.
Single PhaseSplit System Air Conditioner (Outdoor Section)
Legend
Field Wiring
Factory Wiring:
Low Voltage
High Voltage
NOTES:
1. Couper le courant avant de faire letretien.
2. Employez uniquement des conducteurs en cuivre.
3. Ne convient pas aux installations de plus de 150 volt a la terre.
C
H
F
Dual
Capacitor
T1 T2
L1 L2
Contactor
(1 Phase)
Field Supply
L1 GrdL2
Grounding
Screw
C
R
S
C
R
S
See Note 6.
Red or Red Black
Red
Yellow
Black
Start
Capacitor
2
3
Start
Relay
1
Black
Blue
Orange
H
C
F
Dual Capacitor
C
R
S
Outdoor
Fan Motor
Compressor
C
R
S
24 Volt Field
Connections
CC - Contactor Coil
CCH - Crankcase Heater
HPS-High Pressure Switch
CC
CCH (Optional)
Black or
Black White
Yellow or
Yellow Black
Yellow
Outdoor
Fan Motor
Compressor
Crankcase
Heater
(Optional)
208/230V
ASCT
Anti-Short Cycle Timer (ASCT) may or may not be installed in the unit. If desired,
ASCT is factory installed on select models only or may be field installed as shown using
manufacturer's approved kit. If not present, connect Yellow and Black wires per Note 6.
ASCT
T2
T1
T3
Yellow
Black
(See
Note 7.)
ASCT
(See
Note 7.)
Black
Red
or
Yellow
HPS
HPS
T1
T2
T3
Figure 6. JS6BD Wiring Diagram (3.5 & 5 Ton Units)
7103880
15
JS6BD CHARGING CHARTS - COOLING ONLY
Application Notes on the Use of Charging Charts
• This equipment’s cooling system contains refrigerant under high pressure. Always use safe and
environmentally sound methods when handling refrigerant handling or servicing the unit. Review the
factory literature and safety warnings prior to servicing.
• When repairing system leakages, always use a nitrogen (inert) gas to protect the refrigerant system and pressure
check the repair before re-charging. Always replace the fi lter-dryers when performing any repair to the refrigeration
system with one capable of acid removal. After completing the repairs, evacuate the system to 350 - 500 microns
and weigh in the refrigerant to the amount specifi ed on the unit rating label.
• Charging charts are valid for a variety of indoor, return air conditions and are most infl uenced by the outdoor
ambient temperature, outdoor fan operation and the unit operating voltage. Before using these charts, ensure
the unit is in a stable operating mode. As shown in the charging charts (Figures 7 - 12, page 16 - 18), the ideal
system sub-cooling can vary over the range of operation. Reference the charts to determine the ideal amount of
sub-cooling for a given liquid pressure. Units charged to other values will not perform at the rated unit effi ciency
(EER) or rated Coeffi cient of Performance (COP) in heating mode.
• To inspect a systems operation using quality instruments, match the measured liquid temperature to the units
chart. The measured liquid pressure reading should be within 3% of the charts value for most installations.
• For systems that are operating with more than a 5% deviation, inspect the unit for the proper voltage and phase
balance and the refrigeration system for leaks.
• Units that are operating at less then 95% of the nominal voltage or with a 2% phase imbalance may see a more
signifi cant deviation than the amount stated above.
• DO NOT use the charts in systems that have a fan cycling under low-ambient control. Refer to the low-ambient
kit instructions for more information. (If applicable)
16
Figure 7. Charging Chart for 2 Ton Units
Figure 8. Charging Chart for 2.5 Ton Units
250
275
300
325
350
375
400
425
450
475
500
525
550
575
600
75 80 85 90 95 100 105 110 115 120 125 130 135
Liquid Pressure (psig)
S6BD030 TXV Charging Chart
Liquid Temperature ( ° F)
Remove refrigerant when above curve
Add refrigerant when below curve
250
275
300
325
350
375
400
425
450
475
500
525
550
575
600
625
75 80 85 90 95 100 105 110 115 120 125 130 135
Liquid Pressure (psig)
Liquid Temperature ( ° F)
S6BD024 K TXV Charging Chart
Remove refrigerant when above curve
Add refrigerant when below curve
NOTE: Do not add or remove refrigerant if pressure reading is between the curves.
SEE NOTE
SEE NOTE
17
250
275
300
325
350
375
400
425
450
475
500
525
550
575
600
75 80 85 90 95 100 105 110 115 120 125 130 135
Liquid Pressure (psig)
S6BD036TXV Charging Chart
Remove refrigerant when above curve
Add refrigerant when below curve
Liquid Temperature ( ° F)
Figure 9. Charging Chart for 3 Ton Units
Figure 10. Charging Chart for 3.5 Ton Units
250
275
300
325
350
375
400
425
450
475
500
525
550
575
600
75 80 85 90 95 100 105 110 115 120 125 130 135
Liquid Pressure (psig)
S6BD042 K TXV Charging Chart
Liquid Temperature ( ° F)
Remove refrigerant when above curve
Add refrigerant when below curve
SEE NOTE
SEE NOTE
NOTE: Do not add or remove refrigerant if pressure reading is between the curves.
18
250
275
300
325
350
375
400
425
450
475
500
525
550
575
600
75 80 85 90 95 100 105 110 115 120 125 130 135
Liquid Pressure (psig)
S6BD048 K TXV Charging Chart
Liquid Temperature ( ° F)
Remove refrigerant when above curve
Add refrigerant when below curve
Figure 11. Charging Chart for 4 Ton Units
Figure 12. Charging Chart for 5 Ton Units
250
275
300
325
350
375
400
425
450
475
500
525
550
575
600
75 80 85 90 95 100 105 110 115 120 125 130 135
Liquid Pressure (psig)
S6BD060K TXV Charging Chart
Liquid Temperature ( ° F)
Remove refrigerant when above curve
Add refrigerant when below curve
SEE NOTE
NOTE: Do not add or remove refrigerant if pressure reading is between the curves.
SEE NOTE
19
INSTALLATION/PERFORMANCE CHECK LIST
REFRIGERATION SYSTEM:
Was unit given 24 hr warm up period
for crankcase heaters?
YES NO
Stage-1 Liquid Pressure (high side) ________________________
Stage-1 Suction Pressure (low side) ________________________
Has the owner’s information been
reviewed with the customer?
YES NO
Has the Literature Package been left
with the unit?
YES NO
INSTALLATION ADDRESS:
CITY ________________________ STATE ________________
UNIT MODEL # ________________________________________
UNIT SERIAL # _______________________________________
Unit Installed Minimum clearances per
Figure 2 (page 6)?
YES NO
INSTALLER NAME:
CITY _______________________ STATE ________________
ELECTRICAL SYSTEM:
Electrical connections tight? YES NO
Line voltage polarity correct? YES NO
Rated Voltage: ___________________________________ VOLTS
L1-L2 Volts: _____________________________________ VOLTS
L1-L3 Volts: _____________________________________ VOLTS
L2-L3 Volts: _____________________________________ VOLTS
Avg. Volts: ______________________________________ VOLTS
Max. deviation of voltage
from avg. volts: ___________________________________ VOLTS
% Volt imbalance: ________________________________ VOLTS
Blower Motor HP: ________ Sheave Setting ___________# Turns
Has the thermostat been calibrated? YES NO
Is the thermostat level? YES NO
Is the heat anticipator setting correct?
(If Applicable)
YES NO
7090980
¢709098T¤
Specifi cations & illustrations subject to change without notice or incurring obligations.
O’ Fallon, MO | Printed in U.S.A. (05/10)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Broan JS6BD-K Installation guide

JS6BD-K
Broan
Brand
Broan
Model
JS6BD-K
Category
Split-system air conditioners
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents