1
EB100-KU Installation Guide
Package Contents
DFI reserves the right to change the specications at any time prior to the product's release. For the latest revision and details of the
installation procedure, please refer to the user's manual.
www.d.com
•
EB100-KU system unit
• Mounting kit for SATA drive
•
Mounting screws for Mini PCIe and M.2 modules
•
Quick Installation Guide
Panel
Rear View
Front View
Reset switch
HDD LED
USB 2.0
USB 3.0
Power Button with LED
HDMI 2
HDMI 1
12V DC-in
Line-out & Mic-in
LAN 1
LAN 2
2
Removing the Chassis Cover
Please observe the following guidelines and follow the procedure to open the system.
1. Make sure the system and all other peripheral devices connected to it have
been powered off.
2. Disconnect all power cords and cables.
3. The 4 rubber feet on the bottom of the system are used to secure the cover to
the chassis. Remove these screws and put them in a safe place for later use.
Rubber feet
Rubber feet
4. Lift the cover to open the system. The SATA drive bay is on top of the system
board. Remove the SATA drive tray to access the Mini PCIe socket, M.2 socket
and SODIMM sockets.
Mini PCIe socket
M.2 socketSODIMM sockets
3
Installing a SODIMM
Notes:
1. The system supports dual-channel conguration. To enable dual-channel, populate
both SODIMM sockets.
2. If installing only one memory module, please install it on the memory socket
labeled SO_DIMM1 (the one closer to the center of the board).
3. The SODIMM sockets can only accept DDR4 memory modules. Please do not
install other types of memory modules.
The system is equipped with two SODIMM sockets.
To install a SODIMM:
1.
Grasp the module by its edges and align the SODIMM’s notch with the
socket’s key; then insert the SODIMM into the socket at an angle.
2. Press down the other end of the SODIMM module and make sure that you
have inserted the module fully into the socket so that the retaining clips will
snap into place.
SO_DIMM1
SO_DIMM2
4
Installing an M.2 Card
The onboard M.2 Type 2280 connector (M Key) supports SATA SSD only.
To install an M.2 card:
1. Grasp the M.2 card by its edges and align the notch in the bottom edge of the
M.2 card with the key in the connector on the system board.
2. Insert the M.2 card into the connector.
Insert the card
at an angle
Mounting screw
3. Push down on the other end of the M.2 card and secure and card on the main-
board with the provided mounting screw.
5
3. Push down on the other end of the Mini PCIe card and use the provided
mounting screw to secure the card on the system board.
Installing a Mini PCIe Card
The onboard half-size Mini PCIe socket supports PCIe and USB 2.0 interfaces to
accommodate common wireless and cellular communication modules.
To install a Mini PCIe card:
1. Grasp the Mini PCIe card by its edges and align the notch of the PCIe card with
the key in the connector on the system board.
2. Insert the Mini PCIe card into the connector.
Insert the card
at an angle
Mounting screw
Antenna
hole
6
Installing a 2.5” SATA Drive
The SATA drive tray is included in the product package and can accommodate one
SATA drive.
To install a 2.5" SATA:
1. Place the SATA drive on the SATA drive tray and secure it in place with the
provided screws.
Mounting screw
Mounting screw
2. Connect the SATA data and power cable to the drive. Note that this SATA
cable has a SATA power/data interface connecting to a proprietary connector
with predened pin assignments on the system board. Please only use the
provided SATA cable.
SATA power & data cable
7
3. Place the SATA drive tray with the installed SATA drive back into the system (on
top of the system board).
8
Accessing the Jumpers
1.
Before uninstalling the system board, take off the front and back covers.
2. Remove the four screws to take off the system board.
3. Flip the board to access the jumpers.
Top side of the board
The jumpers are located on the back side of the system board and can only be ac-
cessed by taking the board off from the chassis.
9
Board Layout and Jumper Settings
Clear CMOS Data JP1
Normal (default) 1-2 On
Clear CMOS Data 2-3 On
A52901915
USB 3-4
USB 1-2
USB 3.0
USB 3.0
JP1
JP4
DC-in
3
3
USB 6-7
USB 2.0
1
1
Reset
HDMI
1/2
MIC_in
Line_out
Power
Button
LAN 2
LAN 1
DDR4_ SODIMM
DDR4_ SODIMM
Mini PCIe (half-size)
PCIe/USB
M.2 2280
(M Key)
SATA
(CN45)
1
20
Top
Bottom
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
DFI EB100-KU Installation Guide User manual
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
DFI EB100-KU User manual
-
DFI EC531-KH/EC532-KH Owner's manual
-
-
-
-
DFI OPS150-CS User manual
-
-
-
-