Wildfire WFH50-S2P Owner's manual

Brand: Wildfire

Model: WFH50-S2P

Category: Scooters

Type: Owner's manual

This manual is also suitable for

WFH50-S2

Wildfire WFH50-S2P is a gas scooter with a 2-year or 24,000-mile warranty on the engine and transmission. It features an electrical start, left and right handlebar switches for various functions, including lights, signals, and throttle control. The scooter also has a pre-ride checklist for safety and maintenance, including checking fuel, throttle, engine oil, steering, and brakes. It provides general maintenance instructions for tasks like engine oil replacement, spark plug replacement, and valve clearance adjustment.

Have a problem - Need parts - Please call Toll Free (866) 658-7300

Fax: (740) 283-6541 • Email: [email protected]

Model WFH50-S2 Gas Scooter

Owner’s Manual

If you believe that your vehicle has a defect which could cause a crash or could cause injury or

death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA)

in addition to notifying (Zhejiang Huawin Motorcycle Industry Co., Ltd./China).

If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety

defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA

cannot become involved in individual problems between you, your dealer, or (Zhejiang Huawin

Motorcycle Industry Co., Ltd./China).

To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1-800-424-9393 (or 366-

0123 in Washington, DC area) or write to: NHTSA, U.S. Department of Transportation, Washington,

DC 20590. You can also obtain other information about motor vehicle safety from the Hotline.

Table of Contents

Specification..............................................................................................2

Engine Break in Procedure......................................................................3

Description.................................................................................................3

Main Switches........................................................................................... 3

Control Functions.....................................................................................4

Left Handlebar Switches...........................................................................5

Right Handlebar Switches........................................................................5

Electrical Start...........................................................................................5

Brake Levers..............................................................................................5

Pre Ride Check.......................................................................................6-7

Fuel.............................................................................................................6

Throttle.......................................................................................................6

Checking the Engine Oil...........................................................................6

Steering Inspection...................................................................................6

Gear Oil......................................................................................................6

Check Before Riding.................................................................................7

Lights, Signals, Switches and Handlebars.............................................7

Checking Tire and Tire Pressure.............................................................7

Brakes.........................................................................................................7

Brake Fluid Level...................................................................................... 7

Starting Off, Riding, Stopping and Parking............................................8

General Maintenance......................................................................... 9-10

Engine Oil Replacement...........................................................................9

Changing The Engine Oil.........................................................................9

Gear Oil Replacement............................................................................. 9

Spark Plug................................................................................................ 9

Check and Adjustment of Valve Clearance..........................................10

Cleaning of Air Cleaner...........................................................................10

Storage Procedures................................................................................10

Maintenance.............................................................................................10

General Safety Precautions................................................................... 11

Schedule Maintenance Chart.................................................................12

Battery.......................................................................................................12

Capacities.................................................................................................12

Warranty...................................................................................................13-15

Name

Address City State Zip

Dealer Name Model # Date of Purchase

Address City State Zip

! Warranty valid only when purchased from an authorized Wildfire dealer !

Bike is sold as is except for a 2 year or 24,000 mile warranty (which ever comes

first) on the engine and transmission. Wildfire products are sold as is without

warranty, except for a 90 day replacement parts only warranty against

manufacture defects. The warranty does not cover labor, misuse, abuse or

damage in shipping. Assembly, labor, disassembly and reassembly are not the

responsibility of Wildfire Motors; also there are no refunds or exchanges. Within

90 days of purchase, Wildfire Motors will replace any part that is a manufacture

defect at no charge plus a $10.00 shipping and handling fee after the consumer

sends back the defective warranted part to Wildfire Motors. When warranty is

confirmed, Wildfire Motors will ship all parts via DHL ground only. For

replacement parts, please call Wildfire Motors toll free at 866-658-7300 or email

[email protected]. After 90 days from the date of purchase, replacement

parts may be purchased from Wildfire Motors plus a $10.00 shipping and

handling fee.

NOTE: If there is any shipping damage to your unit, you must report this to the

truck line company immediately; you must file a claim with the truck line

company.

Registration must be completed and sent in within seven (7) days of purchase

with a copy of your receipt to validate the warranty. No refunds or exchanges.

NOTE: Absolutely no warranty for consumable and normal wear items such as

spark plugs, oil filters, fuel system cleaning, engine tune-up, belt or chain

adjustments (including replacement), lubrication, light bulbs, clutches, lubricants,

air filters, hoses, brake shoes, tires/tubes, plastic, battery, fuses, cosmetic

problems or problems occurring due to lack of proper assembly or maintenance,

or consumer abuse. Any and all modifications to the vehicle will void the

manufactures warranty. Defective parts are subject to be recalled by WILDFIRE

MOTORS.

Disclaimer:

Wildfire Motors disclaims the warranty of merchantability and fitness for any

particular use. This disclaimer shall be effective as to all claims of any kind made

by or through any wholesaler, retailer, consumer or any other persons or entity.

Some states do not permit this disclaimer of implied warranties. Hence, this

disclaimer may not apply to you.

Limitation of Remedies:

Consumer's remedy is limited to replacement parts only and in no event shall

exceed the purchase price. Absolutely no returns or exchanges. Incidental,

consequential and/or indirect damages are expressly disclaimed. NO person or

entity is authorized to alter, amend or increase this limited warranty.

Warranty Validation:

Please fill out this form and mail it in to Wildfire Motors 11 Technology Way,

Steubenville, Ohio 43952 to register your warranty.

CAUTION - CAUTION - CAUTION - CAUTION - CAUTION - CAUTION

Riders must comply with local allowable age rules and all local laws and

regulations. Minors should never operate this product. DO NOT operate this

product under the influence of alcohol, drugs or while receiving medical

treatment. DO NOT ride this product without protective equipment, such as

helmets, gloves, etc.. and any other protection that local regulations or laws

require.Read the instructions carefully until you understand how to safely start,

stop, turn, and yield to all obstacles in the environment.

• 50cc High Power 4-Stroke Engine

• Electric and Kick Start

• CDI Ignition

• 1 Gallon Gas Tank

• Large Built-in Dual Headlights

• Steel Frame with Heavy Coated Finish

Please have the last 7 digits of your VIN# ready when you call for parts.

Have a problem - Need parts - Please call Toll Free (866) 658-7300 • Email: [email protected]

• CVT (Constant Velocity Transmission)

• High Quality Front and Rear

Drum Brakes

• Heavy Duty 3.5-10 Tires

• Large Comfortable Seat

• Rear Storage Box / Back Rest

• (Optional) Cellphone

Ring Indicator.

CAUTION

• Each time before you ride, make sure the brakes work properly and

adjust if necessary .

• Check bolts for tightness weekly.

• PLEASE CHARGE THE BATTERY AS SOON AS YOU OPEN THE CARTON

AND BEFORE YOU START THE ENGINE. CHARGE WITH A 2 AMP TRICKLE

CHARGER FOR 6-7 HOURS.

• Your sooter maybe equipped with an optional Cellphone Ring Indicator in

the gauge cluster. This feature indicates when your cellphone is ringing

while you are riding.

Specification

WILDFIRE MOTORS

LIMITED WARRANTY

FEDERAL EMISSION CONTROL SYSTEMS

WILDFIRE MOTORS ("WILDFIRE") warrants each new motorcycle that includes as standard

equipment a headlight, taillight and stoplight:

(a) is designed, built and equipped so as to conform at the time of initial retail purchase with all

applicable regulations of the United States Environmental Protection Agency ("US EPA"); and:

(b) is free from defects in material and workmanship which would cause such motorcycle to fail to

conform with applicable regulations of the US EPA, for a period of five (5) years and, depending on

engine displacement: 0-169cc: 12,000km (7,456 miles)

This warranty time and mileage period shall begin on the date the motorcycle is delivered to the

initial retail purchaser, or on the date the motorcycle is first placed in service as a demonstrator,

rental, lease, or company motorcycle prior to retail sale.

1). COVERAGE. Warranty defects shall be remedied during customary business hours at any

authorized WILDFIRE motorcycle dealer located within the United States in compliance with the

Clean Air Act and applicable regulations of the US EPA. Any part or parts replaced under this

warranty shall become the property of WILDFIRE.

2). OWNERS OBLIGATIONS. The following obligations must be fulfilled by the owner to maintain

the validity of the WILDFIRE Emission Control Systems Warranty:

(a) Owner must deliver the motorcycle to an authorized WILDFIRE motorcycle dealer or equally

qualified service facility for inspection, maintenance services and adjustments according to the

Periodic Maintenance chart provided as part of or supplement to the owners guide. Optionally, the

Owner may perform this maintenance only if it is within the scope of the Owner's technical and

practical ability, keeping in mind some maintenance operations may require special tools or

technical expertise beyond the scope of the average Owner. In any event, the inspection,

maintenance and adjustments are to be performed at the owner's expense.

(b) Owner must present a copy of the proof of initial retail purchase date, issued at the time of

purchase to an authorized WILDFIRE motorcycle dealer at the time warranty repairs are performed

on the motorcycle. You may also be required to show that you have performed the required

maintenance which is related to the alleged defect, so you should have detailed receipts indicating

that the required periodic maintenance has been performed in accordance with the Periodic

Maintenance chart in your owner's guide.

3). LIMITATIONS. This Emission Control Systems Warranty shall not cover any of the following:

(a) Repair or replacement required as a result of (i) accident, (ii) misuse or neglect, (iii) lack of

reasonable and proper maintenance, (iv) repairs improperly performed or replacements improperly

installed, (v) use of replacement parts or accessories not conforming to WILDFIRE specifications

which adversely affect performance and/or durability, (vi) alterations or modifications not

recommended or approved in writing by WILDFIRE, and/or (vii) use in competitive racing or related

events.

(b) Replacement of parts and other services and adjustments required for routine maintenance.

cannot be determined.

4). LIMITED LIABILITY.

(a) The liability of WILDFIRE under this Emission Control Systems Warranty is limited solely to the

remedying of defects in materials or workmanship by any authorized WILDFIRE motorcycle dealer

at its place of business during customary business hours. Please refer to WILDFIRE website:

www.wildfiremotors.com. This warranty does not cover inconvenience or loss of use of the

motorcycle, or transportation of the motorcycle to or from the WILDFIRE dealer. WILDFIRE SHALL

NOT BE LIABLE FOR ANY OTHER EXPENSE, LOSS OR DAMAGE, WHETHER DIRECT,

INCIDENTAL, CONSEQUENTIAL OR EXEMPLARYARISING IN CONNECTION WITH THE SALE

OR USE OF OR INABILITY TO USE THE WILDFIRE MOTORCYCLE FOR ANY PURPOSE.

SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF ANY INCIDENTAL OR

CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOTAPPLY

TO YOU.

WILDFIRE MOTORS

LIMITED WARRANTY

NOISE CONTROL SYSTEM WARRANTY

The following warranty applies to the noise control system and is in addition to the Vehicle Warranty

and the Federal Emissions Control System Warranty.

WILDFIRE warrants to the first, and each subsequent Owner, that this vehicle is designed and built

so as to conform at the time of manufacture and sale with applicable Noise regulations of the US

EPA (as tested under F-76 Drive-By FTP), and that it is free from defects in materials and

workmanship which could cause this vehicle not to meet US EPA standards within one (1) year or

6,000 kilometers (3,730 miles), whichever occurs first.

The warranty period shall begin on the date the motorcycle is delivered to the first retail

purchaser or, if the motorcycle is placed in service as a demonstrator or company vehicle prior to

sale at retail, on the date it is first placed in service.

THE FOLLOWING ITEMS ARE NOT COVERED BY THE NOISE CONTROL WARRANTY

1. Failures which arise as a result of misuse, alterations, or accident.

2. Replacing, removing or modifying any portion of the Noise Control System (consisting of the

complete exhaust and intake system, including air filter assembly) with parts not certified to be

Noise-Legal for street use.

3. Loss of time, inconvenience, loss of motorcycle use or other consequential damage or loss.

4. Any motorcycle on which the odometer mileage has been changed so that the actual mileage

cannot be determined.

Please have the last 7 digits of your VIN# ready when you call for parts.

Have a problem - Need parts - Please call Toll Free (866) 658-7300 • Email: [email protected]

Engine Break-In

• CHANGE SHIPPING OIL BEFORE RIDING. Change it to 5W50, 10W50 or

15W50 synthetic oil.This is the most important time for the engine and the life

of your scooter, because your engine is brand new, you should not carry

excessive loads or ride at a high speed for a prolonged period of time. Vary

your speed, do not operate at a continuous speed. Check the oil periodically

and change it at 1,500 miles.

Rear Turn Signals

Brake and Taillight

Dual Headlights

Rearview Mirrors

Turn Signals

Main Switches

On Position:

• Electrical circuits are switched on. The engine can be started and the key can

not be removed.

• Do not leave the main switch in the on position for an extended period of time

if the engine is not running

Off Position:

• All electrical circuits are off and the engine is stopped. The key can be

removed in this position.

Steering Lock Position:

• Turn the handlebars to the left as far as they will turn, turn the key to the lock

position and remove.

Steering Lock

Position

On Position

Off Position

Wildfire WFH50-S2 Maintenance Table

The X indicates at how many miles you need to check the Item.

Must change oil: change before riding, again at 500 miles and then 2500 or

yearly which ever comes first.

Capacities

Fuel Capacity: 1 gallon

Final drive oil capacity: 3.5 ounces

Tire air pressure: Front 28 psi and rear 32 psi.

ITEM 500 1000 2000 2500 3500 4000 4500 5000 6000 6500 Check Daily

Engine Oil and Filter X X X X X X

Gear Oil X X X X

Valve Clearance X X

Cam Chain X X

Carburetor X X

Air Cleaner Clean Every 1500 miles, Replace Every 3500 miles

Fuel Filter Clean Every 1000 miles, Replace if Necessary

Brake System X X X X X X X

Drive Belt X

Screws and Nuts X X X X X

*When riding in a dusty environment, check and clean the air filter element more often.

Battery

• This scooter uses a sealed lead acid battery, it is unnecessary to check or add

liquid.

NOTE:Never open the electrolyte of a sealed battery. Remove the battery from

the scooter and store separately in a well ventilated area when the scooter is not

in operation for long periods of time.

Please have the last 7 digits of your VIN# ready when you call for parts.

Have a problem - Need parts - Please call Toll Free (866) 658-7300 • Email: [email protected]

Control Functions

Speedometer

• Speed is measured in mph.

Odometer

• The total riding distance is indicated.

Fuel gauge

• The gauge indicates how much fuel is in the

tank (the gauge does not work when the

ignition switch is off). The needle moves

from full "F" to empty "E" as your fuel

decreases. Fill the tank with a good grade

of 89-90 octane unleaded gasoline.

High Beam Indicator LIght

• The high beam light indicates that the high beam headlight is in use.

NOTE: Apply the low beam to avoid obstructing the view of other drivers.

Turn Signal Indication Light

• The turn signals indicate that you are turning a chosen direction, push the button in

the desired turning direction, it will return to

the center, press the button in to turn off.

Speedometer

Odometer

Turn Signal

Indication Light

High Beam

Indication Light

Fuel Gauge

General Safety Precaution

• Scooters can be hazardous to operate. Please operate it with the following

safety instruction. If you fail to take proper precautions, a collision or fall may

quickly occur. If you have any questions as to the operating condition of your

scooter, turn off the engine and walk your scooter. These scooters should be

ridden by persons with good vision, balance, coordination, reflex, strength and

decision making capability.

• Please read this manual and all safety labels carefully, and follow correct

operating procedures.

• Before each time you ride make sure that the brakes work properly.

• Never operate your scooter without wearing proper safety equipment that

includes helmet, shoes, etc...

• Never operate your scooter under influence of alcohol or drugs.

• Always ride with both hands on the handle bars.

• Never operate at excessive speeds. Proper speed is determined by terrain,

visibility, operating condition and experience.

• Never attempt wheelies, jumps or other stunts.

• Always inspect your scooter prior to each use to make sure all bolts are tight,

and is in safe operating condition.

• Follow inspection and maintenance procedures and schedules described in

this manual.

• Do not turn at excessive speeds.

• Maintain proper tire pressure: front 28 psi and rear 32 psi.

• Fuel is highly flammable. Keep it away from ignition sources or fire, especially

when refueling, and always make sure engine is cool and not running

when refueling.

• Engine and muffler get hot while in use, do not touch.

• Keep all body parts and clothing away from chains.

Left Handlebar Switches

Dimmer Switch

• When the headlight is in the on position you have two options on the switch:

1. high beam 2.low beam

Turn Signal

• Use the turn signals when turning, pulling over or changing lanes to indicate to the

other motorist which direction you are going. Push the switch to the right to turn

right or push it to the left to turn left. The switch will automatically return to the

center but the light will not go out until you push in on the switch.

Horn Button

Right Handlebar Switches

Light Switch

1. All lights are off.

2. Taillight, licenses plate light

and the dash lights are on.

3. Headlight, taillight, licenses plate light and the dash lights are on.

Electric Start Switch

Turn the key on then push this button to start the bike.

NOTE:

• Make sure all accessory switches are in the off position.

• Apply the rear brake prior to starting the engine.

• Never exceed 4 seconds when using the starter switch.

• Release the starter switch immediately after the engine starts.

• Do not apply the starter switch while the engine is running.

Front and Rear Brake Levers

• The front brake lever is located on the right handlebar and the rear brake lever

is located on the left. Use both brakes when stopping, if the front wheel skids let

off Immediately and reapply.

1. 2. 3.

Check and Adjustment of Valve Clearance

• Excessive valve clearance will cause noise and engine damage. Little or no

clearance will prevent the valve from closing and will cause damage to the valve

and the bike will have loss of power. Check the valve clearance when the engine

is cold.

• Remove the center hole cap from the case cover, generator cover and cylinder

head cover.

• By using a T spanner, rotate the generator flywheel counterclockwise until the

T mark on the flywheel lines up with the index mark on the view hole. In this

case, the piston may either be on the compression or exhaust stroke. The

adjustment must made when the piston is at the TDC (top dead center) of the

compression stroke, and both the intake and exhaust valves are closed.

• This condition can be determined by moving the rocker arms. If they are free, it

is an indication that the valves are closed and that the piston is on the

compression stroke. If they are tight and the valves are open, rotate

the flywheel by 360 degrees and realign the T mark to the index mark.

• Check the clearance of both valves by inserting a feeler gauge between the

adjuster screw and the valve stem.

• The intake valve clearance should be .002 inches and exhaust valve clearance

should be .0024 inches.

• If it is necessary to make an adjustment, loosen the lock nut and turn the

adjusting screw so there is a slight resistance when the feeler gauge is

inserted. After completing the adjustment, tighten the lock nut while holding the

adjusting screw to prevent it from turning. Finally, recheck the clearance to

make sure that the adjustment was not disturbed.

• Reinstall all of the parts to their original positions.

Storage Procedure

• During extended storage, store in a well ventilated area. Empty the fuel tank

and start the engine to clear out the remaining fuel.

Maintenance

• Proper maintenance is important to prolong the life of the scooter and to avoid

injuries to the operator. Check the stability of the handlebar and brake cables to

ensure they are reliable and flexible before each operation. Brake cables may

need adjusted after excessive use. The front tires should be properly

maintained at 28 PSI and the rear at 32 PSI Under inflated or over inflated tires

result in performance loss, tire wear or even tire damage. The scooter should

always be kept in a clean condition and may require some cleaning after each

use. Always use a clean soft cloth to wipe off any dirt or debris that you may of

encountered while riding. Any moisture or rain should be wiped off prior to

storage. Avoid operating the scooter in rain or through water puddles.

Excessive moisture to the electronics will damage them. Avoid storage of the

scooter in moist areas, or near corrosive gases. Proper maintenance will

help prolong the life of the scooter and make your riding experience more

enjoyable. Never exceed the weight capacity of the scooter. Never carry a

passenger. Proper care will result in many years of use.

Please have the last 7 digits of your VIN# ready when you call for parts.

Have a problem - Need parts - Please call Toll Free (866) 658-7300 • Email: [email protected]

Check before Riding

• Make sure the brakes work properly and adjust if necessary.

• Check bolts for tightness.

• Make sure there is plenty of fuel.

• Check tire pressure.

• Check all of the lights, headlight, taillight, turn signal etc.

• Check the engine oil.

Pre Ride Check

Fuel

• Check before you ride. Do not over fill the tank. Fuel capacity: 1 gal.

Throttle

• Turn the throttle and make sure that it turns smoothly, freely

and returns to idle when released.

Checking the Engine Oil

• Place the scooter on a level ground on the center stand.

• If the oil level is below the designated area, add 5W50,

10W50 or 15W50 synthetic oil until the level is between the

lower and upper marks on the dipstick. Do not overfill.

Note: Be sure the scooter is level when checking the oil. Aslight tilt to the left or

right can cause a false reading.

Steering Inspection

• Place the scooter on a stand so that the front wheel is off the ground. Hold the

lower end of the front fork and try to move it forward and backward. If any free

play can be felt consult a mechanic regarding the steering bearings.

NOTE:Securely support the scooter so there is no danger of it falling over.

Final Drive Oil

• Recommended Oil: 5W50, 10W50 or 15W50 synthetic engine oil.

Dipstick

General Maintenance

Engine Oil Replacement

• Replace the engine oil after the first 50 miles with 5w50, 10w50 or 15W50

synthetic engine oil. Then replace again every 1,500 miles. Check oil level every

500 miles, add oil if needed.

Changing the Engine Oil

(1).Warm up the engine for a few minutes.

(2).Stop the engine.

(3). Place scooter on center stand.

(4).Place an oil pan under the engine and remove the dipstick.

(5).Remove the drain plug and drain the oil.

(6).Reinstall drain plug.

(7).Fill the engine with oil and install the dipstick. The recommended 5W50 until the

level is in the designated area on the dipstick.

(8).Start the engine and check for oil leaks. If a leak is

found stop the engine

immediately and look for cause.

Final Oil Replacement

• Replace the gear oil after the first 500 miles with 5W/50

synthetic engine oil. Replace the gear oil again every 4

months or every 2000 miles.

• Replacing the Gear Oil

(1).Put the scooter on the center stand.

(2).Place an oil pan under the gear case.

(3).Remove the oil filler bolt and the drain plug to drain the oil

(4).Reinstall and tighten the drain plug.

(5).Fill the gear case with oil.

(6).Reinstall the oil filler bolt.

(7).Check for oil leakage.

Cleaning Air Cleaner

Be sure to check the air cleaner regularly.

(1).Place the scooter on the center stand.

(2).Unscrew and remove the left side panel.

(3).Remove the air cleaner cover by removing the screws.

(4).Take out the air cleaner by removing the screws.

(5).Remove the air cleaner element and wash it gently, but thoroughly in solvent.

Replace if damaged.

(6).Squeeze out the excess solvent and dry it.

(7).Apply oil to the entire surface of the air cleaner and squeeze out the excess

oil. It should be damp but not dripping.

(8).Install the air cleaner, cleaner cover, and left side panel.

Spark Plug

A7RTC

Gap .035

Lights, Signals, Switches and Handlebars

• Check all lights, meters, indicator lights and electrical connections to make sure

they are all in proper working condition.

• Check the handlebars make sure they turn both ways smoothly.

Tires

• Always check the tires before riding, be sure they are in good condition, check

for nails, glass or any other items that may puncture your tire. Check for cracks

in the side wall. If there are any problems with the tires please

replace immediately.

Tire Pressure

• To ensure maximum performance and safe operation please check the tire

pressure before riding. Do not over inflate your scooters tires because the

handling characteristics are different when the maximum air pressure

has been exceeded.

• Front Tire Pressure: 28 psi (cold)

• Rear Tire Pressure: 34 psi (cold)

Brakes

• Check the brakes before you ride each time if they are soft and spongy or are not

working right, please replace immediately.

• Check your brake fluid level, add if necessary.

• Apply the brakes and make sure that the fluid is not leaking out of the brake

lines or the master cylinder.

NOTE: Brake fluid may destroy painted surfaces or plastic parts, be sure to

clean up all spills.

Brake Fluid Level

1. When checking the fluid level make sure the top of the brake master cylinder

is level by centering the handlebars.

2. Refill with DOT 3 brake fluid. Mixing fluid may result in a harmful chemical reaction

and lead to poor brake performance.

3. Be careful that water does not enter the master cylinder when refilling.

Please have the last 7 digits of your VIN# ready when you call for parts.

Have a problem - Need parts - Please call Toll Free (866) 658-7300 • Email: [email protected]

Starting Off, Riding, Stopping and Parking Before starting,

put the side stand up.

(1).Turn the key to the on position.

(2).Apply the rear brake.

(3).With the throttle at idle position push the electric start button or use the kick

start: if the engine fails to start turn and release the throttle then push the electric

start button or kick start again. Be sure and replace the kick starter to its original

position before riding.

(4).If the bike is on the center stand hold the handle bars with both hands and push

forward, if the bike is on the kick stand hold the bike up and push the kick stand

with your foot.

(5).For a cold engine, let the engine idle for 1-3 minutes before riding.

(6).Sit on the bike keeping one foot on the ground for stability, release the brake and

twist the throttle to accelerate, after you start to accelerate put both feet on the

foot rest only putting them on the ground when coming to a stop.

(7).When coming to a stop decrease your speed by releasing the throttle and

apply both of the brakes, if the front tire begins to skid release and reapply.

(8).Parking: Turn the handlebars to the left as far as they will turn, then turn the

key to the lock position (this will lock the steering, remove the key, to avoid

theft.) Put your kick stand down or use the center stand. NOTE: The muffler

and exhaust pipe are hot. Park away from pedestrians.

(9). Practice in an empty parking lot or driveway until you feel confident enough

to ride on the street.

(10). When preparing to ride on a street make sure the headlights are on, check

for traffic and use your turn signals at all times remember to turn the signals

off after use.

(11). Always remember to obey your local and state laws and regulations.

Wildfire WFH50-S2P Owner's manual

Brand: Wildfire

Model: WFH50-S2P

Category: Scooters

Type: Owner's manual

This manual is also suitable for

WFH50-S2

Download PDF

report

Wildfire WFH50-S2P Owner's manual

This manual is also suitable for

Wildfire WFH50-S2P Owner's manual

Related papers

Other documents