Woodtec XW108 User manual

Page is loading ...

22

INTRODUCTION

Congratulations for choosing this high-quality WOODTEC product! We hope it will

be of great help to you. Remember to read the instruction manual before using

the appliance for the first time in order to ensure safe usage. If you have any

doubt or problems, please contact your dealer or the importer. We wish you safe

and pleasant work with this appliance!

SAFETY INSTRUCTIONS

READ THESE INSTRUCTIONS CAREFULLY AND NOTE THE SAFETY INSTRUCTIONS

AND WARNINGS. USE THE APPLIANCE CORRECTLY AND WITH CARE FOR THE

PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE

TO PROPERTY AND/OR SERIOUS PERSONAL INJURY. KEEP THIS INSTRUCTION

MANUAL SAFE FOR FUTURE USE.

This appliance can be used by children aged from 8 years and above and persons with re-

duced physical, sensory or mental capabilities or lack of experience and knowledge if they

have been given supervision or instruction concerning use of the appliance in a safe way and

understand the hazards involved. Children shall not play with the appliance. Cleaning and

user maintenance shall not be made by children without supervision.

ONLY A QUALIFIED ELECTRICIAN IS ALLOWED TO PERFORM ELECTRICAL INSTALLATIONS

TO THE APPLIANCE.

KEEP WORK AREA CLEAN.

Cluttered areas and benches invite accidents.

CONSIDER WORK AREA ENVIRONMENT.

Do not expose electrical appliances to rain. Do not use electrical appliances in damp or wet

locations. Keep work area well lit. Do not use electrical appliances near the presence of

flammable liquids, gases, powders or dust.

GUARD AGAINST ELECTRIC SHOCK.

Always make sure that the power supply corresponds to the voltage and frequency specified

on the rating label. Avoid body contact with earthed surfaces such as pipes, radiators, cook-

ing ranges, refrigerators etc.

KEEP CHILDREN AWAY.

Do not let visitors touch the appliance or its cord. All visitors should be kept away from work

area.

STORE IDLE ELECTRICAL APPLIANCES.

When not in use, electrical appliances should be stored in a dry, high or locked-up place, out

of reach of children.

DO NOT FORCE THE APPLIANCE.

It will do the job better and safer at the rate for which it was intended.

EN

23

USE THE RIGHT APPLIANCE.

Do not force small tools or attachments to do the job of a heavy duty tool. Do not use tools

for purposes not intended.

DRESS PROPERLY.

Do not wear loose clothing or jewellery; they can be caught in moving parts. Rubber gloves

and non-skid footwear are recommended when working outdoors. Long hair should be tied

up.

ALWAYS WEAR EYE AND EAR PROTECTION.

Also wear a respirator or a dust mask if the operation is dusty.

KEEP GUARDS AND SAFETY DEVICES IN PLACE AND IN GOOD WORKING ORDER.

Do not use the appliance without guards or safety devices, if such exist.

USE DUST EXTRACTION EQUIPMENT.

If the appliance can be connected to a dust extraction or collection facilities, ensure that

they are properly connected and used.

DO NOT ABUSE THE CORD.

Never carry the appliance by the cord or yank it to disconnect it from the socket. Keep the

cord away from heat, oil and sharp edges.

AN EXTENSION CORD SHOULD NOT BE USED UNLESS ABSOLUTELY NECESSARY.

In such case, make sure that the extension cord and its plug match the appliance cord and

plug by type, size, shape and other qualifications, and that the extension cord is properly

wired and in good condition. Do not use extension cord with diameter smaller than 2,5 mm2

or length longer than 20 m, otherwise the motor may be damaged.

SECURE WORK. USE CLAMPS OR A VICE TO HOLD THE WORK.

It is safer than using your hand and it frees both hands to operate the appliance.

DO NOT OVERREACH.

Keep proper footing and balance at all times.

MAINTAIN TOOLS AND APPLIANCES WITH CARE.

Keep cutting tools sharp and clean for better and safer performance. Follow instructions for

lubrication and changing accessories. Inspect the cord periodically and if damaged have it

repaired by an authorized service center. Inspect extension cords periodically and replace if

damaged. Keep handles dry, clean and free from oil and grease.

DISCONNECT ELECTRICAL APPLIANCES ALWAYS WHEN NOT IN USE AND BEFORE

INSTALLING, SERVICING, ADJUSTING, MOVING AND CHANGING ACCESSORIES.

REMOVE ADJUSTING KEYS AND WRENCHES.

Form the habit of checking to see that keys and adjusting wrenches are removed from the

appliance before turning it on.

24

AVOID UNINTENTIONAL STARTING.

Do not carry a plugged-in tool with a finger on the switch. Ensure switch is off when plugging

it in.

WHEN OPERATING THE APPLIANCE OUTDOORS, ONLY USE EXTENSION CABLES SUITABLE

FOR OUTDOOR USE. CHECK THE EXTENSION CABLE FOR NECESSARY MARKINGS FOR

OUTDOOR USE.

ALWAYS STAY ALERT AND WATCH WHAT YOU ARE DOING.

Use common sense when operating the appliance. Do not use the appliance while you are

tired, sick or under the influence of alcohol, drugs, medication or other substances that

could affect your ability to react.

CHECK THE APPLIANCE FOR DAMAGES.

If you notice any damages in the appliance, in its guards or other parts, do not use it until it

has been repaired in an authorized service center. Check for alignment of moving parts, free

running of moving parts, breakage of parts, mounting and any other conditions that may

affect the appliance operation. Damaged parts should be properly repaired or replaced by

an authorized service center unless otherwise indicated in this instruction manual. Have de-

fective switches replaced by an authorized service facility. Do not use the appliance if the

switch does not turn it on and off.

USE ONLY ORIGINAL SPARE PARTS AND ACCESSORIES.

The use of any other spare parts or accessories than original parts may cause a risk of per-

sonal injury.

REPAIRS SHOULD ONLY BE CARRIED OUT BY AN AUTHORIZED SERVICE CENTER USING

ONLY ORIGINAL SPARE PARTS, OTHERWISE THIS MAY RESULT IN CONSIDERABLE DANGER

TO THE USER.

TECHNICAL

DATA

Motor 1800 W / 230 V~50 Hz

Rotation speed 5000 rpm

Blade 216 x 30 mm Z40

Sawing angles 45°, 30°, 22,5°, 15°, 0°, -15°, -22,5°, -30°, -45°

Max. sawing capacity (mitre

saw) 90°/90°: 58 x 120 mm (22 x 170 mm)

0°/45°: 40 x 120 mm (22 x 170 mm)

45°/0°: 58 x 85 mm (22 x 120 mm)

45°/45°: 40 x 85 mm (22 x 110 mm)

Max. sawing capacity (table

saw) 90°: 52 mm

45°: 25 mm

Weight 26 kg

Dimensions (LxWxH) 570 x 610 x 1120 mm

This product fulfils the requirements of quality class HA ISO 2807.

25

PRODUCT DESCRIPTION

Parts

Application range

This flip over saw is suitable for longitudinal and transversal sawing, cutting and mitre saw-

ing of wood and soft plastic types. It is not allowed to saw round pieces (tubes, round wood

etc.) with the machine. It is not allowed to saw metal with the machine.

PRIOR TO USE

Unpack the appliance and check that all parts are included. If any part is missing or dam-

aged, contact your dealer immediately. Dispose all packing material according to local regu-

lations.

Pay attention to ergonomics while using the machine. The machine should be placed in such

a way that there is minimum 80 cm of free space around it. This guarantees that the clean-

ing, maintenance and required adjustments can be performed according to the valid safety

regulations.

1. Dust collector hood

2. Hood fastening screw

3. Pusher

4. Socket wrench

5. Work support

6. Work support for mitre sawing

7. Saw blade protection

8. Dust bag

9. Clamp

10. Main part

1. Riving knife

2. Dust collector connection

3. Saw blade protection

4. Locking screw

5. Emergency stop

6. Feet

26

Assembly

1. Lift the main part carefully to the

position shown in the picture.

2. Loosen the locking screws until the

feet are turned under the table.

Tighten the screws.

3. Set the machine on its legs.

Table sawing

- When you use the machine as a table

saw, press the lever (B) down and

turn the table until it snaps into

place.

- Loosen the wing bolt (C).

- The riving knife cylinder (D) has two

grooves and it can be set to two posi-

tions.

- Use the lever (E) that is in the handle

of the machine and locks the saw

blade protection.

- Pull the saw blade protection up-

wards and mount the riving knife.

Tighten the wing nut.

Note: make sure that there is enough

space between the riving knife and the

blade.

27

- Turn the screw (D) as much as possible

so that the saw part folds down.

- Use the lever (F) and turn the table until

it is in the right place.

- When you push the saw blade protec-

tion button (B), blade protection is at-

tached to the riving knife.

- If you do not use dust collector, you can

place the dust bag under the table.

- Work supports (D and E)

The machine is now ready for use as

table saw.

Cutting and mitre sawing

Push the lever (F) down in order to release

the table. Now you can flip over the table.

Attach the table appropriately.

Push the orange button (G), turn it and

release. Now you can adjust the blade

with the lever (H).

- Adjust the riving knife with the wing nut

(N). The riving knife has to be moved to

the right as shown in the picture so that

it is parallel with the blade.

- Use different groove than with table

saw.

- Set the height adjustment to the maxi-

mum level by turning the height ad-

justment screw (I) to the right (in the

opposite than when used as a table

saw).

- Attach the dust collector hood (J) under

the table. Fix it first with the hooks un-

der the table and then with screws (K)

to the opposite side. If you do not use a

dust collector, attach the dust bag to

the outlet.

The machine is now ready for cutting

and mitre sawing.

28

SPECIFIC SAFETY INSTRUCTIONS

- All safety and protection devices must be properly installed before the machine is used.

- Never process wood pieces that are too small to be held properly.

- Saw blade must rotate unrestricted.

- When sawing processed wood, note that it may contain nails, screws or other metallic

objects. Remove all foreign objects from the wood before sawing.

- Before switching the machine on make sure that the saw blade is properly fixed and the

moving parts of the machine move unrestricted.

- Note: If you are uncertain, consult a professional about the correct installation.

OPERATION

Setting the angle

Saw angle 0–45˚ can be read on the scale. Set the angle with the arrester (H) and by tilting

the saw. Adjust the saw blade setting by loosening the screw (J) and turning the saw.

Switching on and off

To turn on the machine, press the green switch ”I”.

Switch off the machine by pressing the red ”O” button.

The machine is equipped with an emergency stop button.

Cutting

Place the work support at the desired distance from the blade. Place the work piece against

the work support. Place the flat or wide side horizontally on the sawing table. ATTENTION:

Keep always a sufficient safety distance to the blade.

29

Bevel cuts

Fix the work piece with a clamp as shown in the picture. Set the desired angle with the ar-

rester. Make sure that the riving knife is parallel with the blade. Tighten the arrester. Start

the machine and start cutting by pushing the blade carefully downwards.

Skew cuts

Install the work support for mitre sawing in the desired groove and set the desired angle.

Start the machine and move the work piece carefully towards the blade using the work sup-

port. ATTENTION: Always secure the workpiece. Never secure the workpiece on that part

that is cut off.

Adjustment of the riving knife

The riving knife can be set to two different positions. In order to obtain maximum grooving

capacity, the riving knife is set to the lowest position, which limits the maximum depth of cut.

Distance between the table and upper end is approx. 10 cm. In order to obtain the maximum

depth of cut, the riving knife is set so that its top is no more than 2 mm above the highest

tooth tip of the saw blade. Set the riving knife so that the closest point is between 3 and 8

mm away from the saw blade.

Loosen the riving knife screw and move the knife according to the chosen sawing type.

Tighten the screw.

30

MAINTENANCE

Replacing the blade

ATTENTION: Always shut off and disconnect the machine before maintenance or replacing

the saw blade.

- Press the lever (X) down and hold it down in order to lock the blade.

- Use the provided wrench or spanner to loosen the saw blade nut. Rotate the nut clock-

wise.

- Remove the blade.

- Clean the flange carefully before installing the new blade.

- Install the blade and reassemble in reverse order.

- ATTENTION: Check the rotation direction of the blade.

- Before restarting make sure that all the safety and protection devices work properly.

- When the blade is installed make sure that it rotates unrestricted.

- Start the machine and let it run without load before you start sawing.

Periodic maintenance

The saw will work properly only if it is maintained carefully. Improper mainte-

nance may lead to unexpected accidents or damages.

- Unplug the machine before any maintenance.

- Clean the plastic parts with a moist cloth.

- Do not use cleaning products, solvents or pointed objects for cleaning.

- Remove dirt on the table surface with proper cleaning spray.

- If it takes more than 10 seconds for the motor to stop, the wearing parts must be re-

placed.

- After use remove the dust from the ventilation openings and moving parts with a soft

brush.

- Lubricate all moving parts regularly.

- Do not use compressed air jets for cleaning!

- Regularly check the blade: if difficulties should arise during cutting, have it sharpened by

skilled personnel or replace it if necessary.

Page is loading ...

Woodtec XW108 User manual

Woodtec XW108 User manual

in other languages

Related papers

Other documents