AGI Inline Centrifugal Aeration Fan Owner's manual

Brand: AGI

Model: Inline Centrifugal Aeration Fan

Type: Owner's manual

Read this manual before using product. Failure to

follow instructions and safety precautions can

result in serious injury, death, or property

damage. Keep manual for future reference.

Part Number: INA-1814 R5

Revised: July 2017

Aeration Fan

Inline Centrifugal Fan

Installation, Operation, and Parts Manual

This manual applies to:

GGI-803XX, GGI-805XX, GGI-807XX, GGI-810XX

Original Instructions

INSTALLATION AND WIRING MUST BE IN

ACCORDANCE WITH CEC, NEC, AND LOCAL

ELECTRICAL CODES

We strongly recommend that all personnel associated with this equipment be trained in the correct operational

and safety procedures required for this product. This product has been designed and constructed according to

general engineering standards, other local regulations may apply and must be followed by the operator. Use the

sign-off sheet below to record initial and periodic reviews of this manual with all such personnel.

Date Employee Signature Employer Signature

New Fan Features

Change Description

Control box change Control box size and construction altered from

previous models.

Thermal overload relay Thermal overload relay now added to control circuit,

no need for field wiring of external unit.

Control box vibration isolation Control box now isolated from fan vibration.

New in this Manual

The information below summarizes the changes to this manual since the last revision in April 2016.

Description Section

Electrical schematics updates Section 7.1. – Electrical Schematics on page 31

Troubleshooting updates Section 6. – Troubleshooting on page 29

New components Section 7.2. – Parts List on page 33

4 INA-1814 R5

AERATION FAN – INLINE CENTRIFUGAL FAN

INA-1814 R5 5

CONTENTS

1. Introduction ............................................................................................................................................ 7

1.1. General Description.................................................................................................................. 7

1.2. Serial Number Location............................................................................................................ 7

1.3. Intended Use ............................................................................................................................ 8

2. Safety....................................................................................................................................................... 9

2.1. Safety Alert Symbol and Signal Words..................................................................................... 9

2.2. General Safety .......................................................................................................................... 9

2.3. Fan Safety ............................................................................................................................... 10

2.4. Guards Safety ......................................................................................................................... 10

2.5. Lockout/Tagout Safety ........................................................................................................... 10

2.6. Electric Motor Safety.............................................................................................................. 11

2.7. Personal Protective Equipment.............................................................................................. 11

2.8. Safety Equipment ................................................................................................................... 11

2.9. Safety Decals .......................................................................................................................... 12

2.9.1 Decal Installation/Replacement............................................................................... 12

2.9.2 Safety Decal Locations and Details .......................................................................... 12

3. Installation ............................................................................................................................................ 19

3.1. Installation Safety................................................................................................................... 19

3.2. Check Shipment...................................................................................................................... 19

3.3. Handling the Fan .................................................................................................................... 19

3.4. Storing the Fan Before Installing............................................................................................ 19

3.5. Installing with a Supplemental Heater................................................................................... 20

3.6. Transition Connection Requirements .................................................................................... 20

3.7. Mounting the Fan on a Flat Bottom Bin ................................................................................ 20

3.7.1 Slab Mounted Fans................................................................................................... 20

3.8. Mounting the Fan on a Hopper Bottom Bin .......................................................................... 21

3.9. Electrical Connection.............................................................................................................. 21

3.10. Testing .................................................................................................................................. 23

4. Operation .............................................................................................................................................. 24

4.1. Operation Safety .................................................................................................................... 24

4.2. Start-Up and Break-In............................................................................................................. 24

4.3. Roof Vents .............................................................................................................................. 24

4.4. Fan Rotation and Orientation ................................................................................................ 25

4.5. Emergency Stop...................................................................................................................... 25

4.6. Shutdown ............................................................................................................................... 26

4.7. Storage.................................................................................................................................... 26

5. Maintenance ......................................................................................................................................... 27

5.1. Maintenance Safety ............................................................................................................... 27

5.2. Maintenance Schedule........................................................................................................... 27

5.3. Visually Inspect the Inline Fan................................................................................................ 28

5.4. Cleaning the Fan Blade and Housing ..................................................................................... 28

5.5. Servicing and Part Replacement ............................................................................................ 28

6. Troubleshooting.................................................................................................................................... 29

7. Appendix ............................................................................................................................................... 31

7.1. Electrical Schematics .............................................................................................................. 31

AERATION FAN – INLINE CENTRIFUGAL FAN

6 INA-1814 R5

7.2. Parts List ................................................................................................................................. 33

7.2.1 Grain Guard Inline Centrifugal Fan — GGI-803XX ................................................... 33

7.2.2 Grain Guard Inline Centrifugal Fan — GGI-805XX ................................................... 34

7.2.3 Grain Guard Inline Centrifugal Fan — GGI-807XX ................................................... 35

7.2.4 Grain Guard Inline Centrifugal Fan — GGI-810XX ................................................... 36

7.3. Grain Drying and Aeration Tips.............................................................................................. 37

8. Warranty ............................................................................................................................................... 41

INA-1814 R5 7

1. Introduction

Thank you for purchasing a Grain Guard Aeration Fan. This equipment will allow safe and efficient

operation when you read and follow all of the instructions contained in this manual. With proper care,

your inline fan will provide you with many years of trouble-free operation.

Keep this manual handy for frequent reference and to review with new personnel. A sign-off form is

provided on the inside front cover for your convenience. If any information in this manual is not

understood or if you need additional information, please contact your local distributor or dealer for

assistance.

This manual should be regarded as part of the equipment. Suppliers of both new and second-hand

equipment are advised to retain documentary evidence that this manual was provided with the

equipment.

1.1. General Description

The Grain Guard Aeration Fan is an excellent addition to any new or existing bin. It can allow you to harvest in

damp conditions, maintain stored grain in peak condition, and reduce the likelihood of mould growth and insect

infestations. With proper care during and after installation, your fan will provide you with many years of

trouble-free service.

1.2. Serial Number Location

Always give your dealer the serial number on your inline fan (shown below) when ordering parts or requesting

service or other information. Please record this information in the table below for easy reference.

Model Number

Serial Number

Date Received

AERATION FAN – INLINE CENTRIFUGAL FAN 1. INTRODUCTION

8 INA-1814 R5

1.3. Intended Use

The inline fan is designed solely for use in the intended agricultural use as listed below. Use in any other way is

considered as contrary to the intended use. Compliance with and strict adherence to the conditions of

operation and maintenance as specified by the manufacturer, also constitute essential elements of the intended

use.

The inline fan should be operated, maintained, serviced, and repaired only by persons who are familiar with its

particular characteristics and who are acquainted with the relevant safety procedures.

Accident prevention regulations and all other generally recognized regulations on safety and occupational

medicine must be observed at all times.

Any modifications made to the inline fan may relieve the manufacturer of liability for any resulting damage or

injury.

Intended use for the inline fan:

• Aeration and natural air drying of grain products.

• Connection to a Grain Guard downstream heater (if required).

Use in any other way is considered as contrary to the intended use and is not covered by the warranty.

1. INTRODUCTION AERATION FAN – INLINE CENTRIFUGAL FAN

INA-1814 R5 9

2. Safety

2.1. Safety Alert Symbol and Signal Words

This safety alert symbol indicates important safety messages in this manual. When you see

this symbol, be alert to the possibility of injury or death, carefully read the message that

follows, and inform others.

Signal Words: Note the use of the signal words DANGER,WARNING,CAUTION, and NOTICE with the safety

messages. The appropriate signal word for each message has been selected using the definitions below as a

guideline.

Indicates an imminently hazardous situation that, if not avoided, will result in serious injury or

death.

Indicates a hazardous situation that, if not avoided, could result in serious injury or death.

Indicates a hazardous situation that, if not avoided, may result in minor or moderate injury.

Indicates a potentially hazardous situation that, if not avoided, may result in property damage.

2.2. General Safety

The safety information in the safety section of this manual applies to all safety practices. Specific safety

information (such as Operation Safety), can be found in the appropriate section.

YOU are responsible for the SAFE use and maintenance of your inline fan. YOU must ensure that you and

anyone else who is going to work around the inline fan understands all procedures and related SAFETY

information contained in this manual.

Remember, YOU are the key to safety. Good safety practices not only protect you, but also the people around

you. Make these practices a working part of your safety program. All accidents can be avoided.

• It is the inline fan owner, operator, and maintenance personnel's responsibility to

read and understand ALL safety instructions, safety decals, and manuals and follow

them when assembling, operating, or maintaining the equipment.

• Owners must give instructions and review the information initially and annually with all personnel before

allowing them to operate the inline fan. Untrained users/operators expose themselves and bystanders to

possible serious injury or death.

• The inline fan is not intended to be used by children.

• Use the inline fan for its intended purposes only.

• Do not modify the inline fan in any way without written permission from the manufacturer. Unauthorized

modification may impair the function and/or safety, and could affect the life of the inline fan. Any

unauthorized modification of the inline fan will void the warranty.

AERATION FAN – INLINE CENTRIFUGAL FAN 2. SAFETY

10 INA-1814 R5

2.3. Fan Safety

• Keep away from fan impeller/blade; high suction can pull a

person toward the inlet. Contact with an unguarded

impeller/blade will cause severe injury.

• Keep the inlet screen in place at all times.

• Remove foreign material from the fan inlet before operating.

• Do not operate the fan if there is excessive vibration or noise.

• When the power is locked out, fans can still be dangerous

because of potential “windmilling.” Always block the

impeller/blade before working on any moving parts.

2.4. Guards Safety

• Keep guards in place. Do not operate with guard removed.

• Do not walk on, step on, or damage guards.

• Lock out power before removing a guard.

• Ensure all guards are replaced after performing maintenance.

2.5. Lockout/Tagout Safety

Lockout/Tagout equipment before set-up, service, maintenance, and repair. Make sure to follow lockout and

tagout procedure in the Electric Motor Safety Section to prevent inadvertent start-up and hazardous energy

release.

2. SAFETY AERATION FAN – INLINE CENTRIFUGAL FAN

INA-1814 R5 11

2.6. Electric Motor Safety

Power Source

• Electric motors and controls shall be installed and serviced by

a qualified electrician and must meet all local codes and

standards.

• Do not modify the magnetic starter. This component provides

overload and under-voltage protection.

• Motor starting controls must be located so that the operator

has full view of the entire operation.

• Locate main power disconnect switch within reach from

ground level to permit ready access in case of an emergency.

• Motor must be grounded.

• Guards must be in place and secure at all times.

• Ensure electrical wiring and cords remain in good condition;

replace if necessary.

SERVICE DISCONNECT

OFF

Lockout

• The main power disconnect switch should be in the locked position during shutdown or

whenever maintenance is performed.

• In the event of unexpected fan shutdown, the fan can be reset using the main power switch

located on the fan or using a reset button when equipped.

2.7. Personal Protective Equipment

The following Personal Protective Equipment (PPE) should be worn when operating or maintaining the

equipment.

Work Gloves

• Wear work gloves to protect your hands from sharp and rough edges.

2.8. Safety Equipment

The following safety equipment should be kept on site:

Fire Extinguisher

• Provide a fire extinguisher for use in case of an accident. Store in a highly visible and

accessible place.

AERATION FAN – INLINE CENTRIFUGAL FAN 2. SAFETY

12 INA-1814 R5

First-Aid Kit

• Have a properly-stocked first-aid kit available for use should the need arise, and

know how to use it.

2.9. Safety Decals

• Keep safety decals clean and legible at all times.

• Replace safety decals that are missing or have become illegible. See decal location figures that follow.

• Replaced parts must display the same decal(s) as the original part.

• Replacement safety decals are available free of charge from your distributor, dealer, or factory.

2.9.1 Decal Installation/Replacement

1. Decal area must be clean and dry, with a temperature above 50°F (10°C).

2. Decide on the exact position before you remove the backing paper.

3. Align the decal over the specified area and carefully press the small portion with the exposed sticky backing

in place.

4. Slowly peel back the remaining paper and carefully smooth the remaining portion of the decal in place.

5. Small air pockets can be pierced with a pin and smoothed out using the sign backing paper.

2.9.2 Safety Decal Locations and Details

Replicas of the safety decals that are attached to the inline fan and their messages are shown in the figure(s)

that follow. Safe operation and use of the inline fan requires that you familiarize yourself with the various safety

decals and the areas or particular functions that the decals apply to, as well as the safety precautions that must

be taken to avoid serious injury, death, or damage.

2. SAFETY AERATION FAN – INLINE CENTRIFUGAL FAN

INA-1814 R5 13

Note

• Electrical schematics (PN 601-4093 / 601-4095 / 601-4096 / 601-4097) attached under the electrical

enclosure lid will depend on the electric motor power source.

• Electrical schematics are also shown in the Appendix section of this manual.

• Voltage warning will be different for each type of electric motor that is used in this fan.

AERATION FAN – INLINE CENTRIFUGAL FAN 2. SAFETY

14 INA-1814 R5

Table 1. Safety Decals

Part Number Description

601–1992

To prevent possible roof damage,

ensure that all roof vents are open

and unobstructed.

Do not operate aeration fan if it is

possible that the roof vents could

ice up.

NOTICE

601–1993

To prevent serious injury or death:

• Read operator’s manual and all product safety decals

before installing, operating or servicing fan.

• Do not operate with any safety shield or guard

removed or modified. Keep in good working order.

• Do not operate fan if there is excessive vibration or

noise.

• Before operating fan, clear work area of all children

and untrained personnel.

• Keep hands, legs, feet, hair, jewelry and clothing away

from all moving parts.

• Shut off and lock out or disconnect power before

inspecting or servicing fan.

If the operator manual, guards, or safety decals

are missing or damaged, contact AGI Nobleford

at 1-800-565-2840 or www.aggrowth.com for

replacements.

AERATION FAN SAFETY INSTRUCTIONS

WARNING

2. SAFETY AERATION FAN – INLINE CENTRIFUGAL FAN

INA-1814 R5 15

Table 1 Safety Decals (continued)

Part Number Description

601–1994

CUTTING HAZARD

To prevent serious injury, keep away

from blade when fan is operating.

Shut off and lockout or disconnect power

before inspecting or servicing.

Keep guards in place while operating.

WARNING

CNA-1391

230 VOLTS

DANGER

CNA-1390

460 VOLTS

DANGER

CNA-1389

575 VOLTS

DANGER

CNA-1399

Disconnect electrical power at

service box before removing cover.

ELECTROCUTION HAZARD

WARNING

AERATION FAN – INLINE CENTRIFUGAL FAN 2. SAFETY

16 INA-1814 R5

Table 1 Safety Decals (continued)

Part Number Description

601–1995

To prevent serious injury or death:

• Only qualified personnel should service

electrical components.

• Disconnect and lockout power before

inspecting or servicing unit.

• Keep electrical components in good repair.

ELECTROCUTION HAZARD

WARNING

CNA-1384

OFF - RUN - MOMENTARY

START

601–4093

2. SAFETY AERATION FAN – INLINE CENTRIFUGAL FAN

INA-1814 R5 17

Table 1 Safety Decals (continued)

Part Number Description

601–4095

601–4096

AERATION FAN – INLINE CENTRIFUGAL FAN 2. SAFETY

18 INA-1814 R5

Table 1 Safety Decals (continued)

Part Number Description

601–4097

2. SAFETY AERATION FAN – INLINE CENTRIFUGAL FAN

INA-1814 R5 19

3. Installation

Before continuing, ensure you have completely read and understood this manual’s

Safety section, in addition to the safety information in the section(s) below.

3.1. Installation Safety

• Do not take chances with safety. The components can be large, heavy, and hard to handle.

Always use the proper tools, rated lifting equipment, and lifting points for the job.

• Always have two or more people installing the inline fan.

• Make sure you have sufficient lighting for the work area.

• Tighten all fasteners according to their specifications. Do not replace or substitute bolts,

nuts, or other hardware that is of lesser quality than the hardware supplied by the

manufacturer.

3.2. Check Shipment

Inspect the inline fan and accessories on receipt to ensure that all items have arrived and that none are

damaged.

A few basic items to check:

• Ensure no loose items or debris that can be drawn into the fan or dislodged by the fan discharge. Check the

interior of the fan as well.

• Turn the fan impeller/blade by hand to check for binding.

• Check the tightness of all nuts and bolts.

• Verify that the supply voltage is correct.

Report missing or damaged parts immediately to ensure that proper credit is received from Grain Guard or your

distributor/dealer, and to ensure that any missing parts can be shipped quickly to avoid holding up the

installation.

Important

Do not use damaged components.

3.3. Handling the Fan

Lift the fan by the base, mounting supports, or lifting locations. Never lift a fan by the wheel, motor, motor

bracket, housing inlet, outlet, or any fan part not designed for lifting. A spreader should always be used to avoid

damage.

3.4. Storing the Fan Before Installing

Check the fan wheel for free operation and lubricate moving parts prior to storage if the fan is not to be placed

immediately into service. Inspect the stored unit periodically.

AERATION FAN – INLINE CENTRIFUGAL FAN 3. INSTALLATION

20 INA-1814 R5

3.5. Installing with a Supplemental Heater

Any type of supplemental heater intended for use with this fan must be installed downstream of this fan and

may be added if extra conditioning or drying is required.

Heating incoming air will damage the fan and its components and is not covered by the

warranty.

3.6. Transition Connection Requirements

When connecting the transition, ensure the fan fits properly with the grain bin transition intended for use by

the manufacturer.

3.7. Mounting the Fan on a Flat Bottom Bin

The inline fan must be properly supported for smooth operation.

3.7.1 Slab Mounted Fans

A concrete foundation is preferable for installing floor-mounted fans.

When installing the fan on a concrete pad the following general requirements apply:

• The concrete surface must be flat and level.

• The weight of the slab should be two to four times the weight of the rotating assembly, including the motor.

• The foundation requires firmly anchored fasteners such as the anchor bolts shown below. Hammer-drilled

expansion fasteners can be used in less demanding applications.

• The overall dimensions of the concrete base should extend at least six inches beyond the base of the fan.

• Locate the fan as close to the bin as possible, leaving approximately 12” to 18” or more between the fan

and bin to allow for routine servicing and inspection.

• Ensure moisture is not accumulating around the fan.

• Move the fan to the mounting location and lower it over the anchor bolts, leveling the fan with shims

around the bolts. Fasten the fan securely.

• When grout is used: Shim the fan at least 3/4-inch from the concrete base.

Item Description

1Transition (Not Load Bearing)

2Concrete Slab

3Concrete Anchor

4Adaptor

3. INSTALLATION AERATION FAN – INLINE CENTRIFUGAL FAN

Page is loading ...

AGI Inline Centrifugal Aeration Fan Owner's manual

AGI Inline Centrifugal Aeration Fan Owner's manual

AGI Inline Centrifugal Aeration Fan Owner's manual

Related papers

Other documents