Page is loading ...
YOUR SAFETY &
INSTRUCTION MANUAL
PLEASE READ CAREFULLY
www.signaturebrand.co
4 IN 1
GROOMING SET
MODEL S090
2
SERVICE DEPARTMENT: +44 (0) 333 220 6062
TECHNICAL DATA
Description: 4 In 1 Grooming Set
Model: S090
Clipper AC: 220-240V 50Hz 12W
Shaver: DC1.2V
600mAh
Nose Trimmer: DC 1.5V (1 x AA Battery)
DOCUMENTATION
We declare that this product conforms to the following product legislation in accordance with the
following directive(s):
2004/108/EC Electromagnetic Compatibility Directive.
2006/95/EC Low Voltage Directive.
2011/65/EU Restriction of Hazardous Substances Directive.
RKW Quality Assurance, United Kingdom
WARRANTY
This product is guaranteed for 12 months from the date of original purchase. If any defect arises due
to faulty materials of workmanship, the faulty products must be returned to the place of purchase.
Refund or replacement is at the discretion of the retailer.
The following conditions apply:
• The product must be returned to the retailer with proof of purchase.
• The product must be installed and used in accordance with the instructions contained in this
instruction guide.
• It must be used only for domestic purposes.
• It does not cover wear and tear, damage, misuse or consumable parts.
• RKW has limited liability for incidental or consequential loss or damage.
• This guarantee is only Valid in the UK and Eire Only.
An extended warranty is available for this appliance.
See back page for details.
3
www.signaturebrand.co
PRODUCT SAFETY
When using any electrical appliance, basic safety precautions should
always be followed including the following:
• Check that the voltage of the
main circuit corresponds with
the rating of the appliance
before operating.
• Please ensure that the appliance
is used on a stable, level, and
heat resistant surface.
• Do not immerse cords, plugs
or any part of the appliance in
water or any other liquid.
• Do not leave the appliance
unattended while it is operating.
• Close supervision is necessary
when any appliance is used by
or near children or pets.
• This appliance can be used
by children aged from 8 years
and above and persons with
reduced physical, sensory or
mental capabilities or lack of
experience and knowledge
if they have been given
supervision or instruction
concerning use of the appliance
in a safe way and understand
the hazards involved.
• Children shall not play with the
appliance.
• Cleaning and user maintenance
shall not be made by children
without supervision.
• Switch off at the wall socket
then remove the plug from
the socket when not in use or
before cleaning.
• If the supply cord or appliance
is damaged, stop using the
appliance immediately and seek
advice from the manufacturer
or its service agent or a similarly
qualied person.
• Do not let the cord hang over
the edge of a table or counter or
let it come into contact with any
hot surfaces.
• The use of accessory
attachments is not
recommended by the appliance
manufacturer, apart from those
supplied with this product.
• Do not pull the plug out by the
cord as this may damage the
plug and/or the cable.
• Do not use this product for
anything other than its intended
use.
• This appliance is for household
use only.
• Do not carry the appliance by
the power cord.
• Do not use the appliance
outdoors.
4
SERVICE DEPARTMENT: +44 (0) 333 220 6062
• Do not use while bathing, or
place or store appliance where
it can fall or be pulled into tub or
sink.
• Do not use the appliances
on irritated skin or skin with
varicose vein, rashes, spots,
moles or wounds without
consulting your doctor rst
• Using the appliance may cause
reddening or irritation of the skin.
This is a normal reaction that
quickly disappear. However, you
should consult your doctor if the
irritation has not disappeared
within three days.
• People with a reduced immune
response, e.g. during pregnancy,
or people who suffer from
diabetes mellitus, haemophiliac
or immunodeciency should
also consult their doctor rst.
• To prevent damage and injuries,
keep the running appliance
away from your hair, eyebrow,
eyelashes, clothes, threads,
cord, brushes, etc.
• Only use the appliance in
combination with adaptor
supplied.
• Do not use any extension cord
with this appliance.
• For additional protection, the
installation of a residual current
device (RCD) having a rated
residual operating current not
exceeding 30 mA is advisable
in the electrical circuit supplying
the bathroom. Ask your installer
for advice.
• If any appliance or charging
unit falls into water, unplug it
immediately. DO NOT REACH
INTO WATER!
• Never use while sleeping or
drowsy.
• Do not place the appliance on
any surface while it is operating
or while the switch is turned on.
• In the unlikely event the
appliance develops a fault,
stop using it immediately and
seek advice from the service
department.
HIGH VOLTAGE ROTATING PARTS
5
www.signaturebrand.co
WHAT’S IN THE BOX
Instruction Manual
1. Clippers
2. Shaver
3. Trimmer
4. Clipper Guards
5. Cleaning Brush &
Lubricating Oil
6. Scissors & Comb
1
4 65
2 3
BEFORE YOUR FIRST USE:
1. Remove your appliance from the packaging.
2. Inspect the clippers, making sure that they are free of oil between the cutting blade teeth and
turn the unit on to distribute the oil and to make sure it is running smoothly.
3. Switch off the unit and Wipe off any excess oil. This should be done after each use.
4. While using the unit, untwist the cord from time to time to avoid tangling.
Dispose of the packaging in a responsible manner.
6
SERVICE DEPARTMENT: +44 (0) 333 220 6062
USING YOUR APPLIANCE
Hair Clippers:
1. Seat the person so their head is
approximately at your eye level. This
allows ease of visibility while cutting and a
relaxed control of the unit.
2. Before cutting always rst comb the hair
so it is tangle free and as it is naturally
worn.
3. Place a towel around the neck and
shoulders of the person having the haircut
reminders.
4. Cut the hair in a relaxed and slow manner.
Use short strokes only to work gradually
over the entire head.
5. Always take off a little hair at a time; you
can always trim off additional hair later.
6. As you work, comb the hair frequently
back into the style to which you are
cutting.
7. When cutting with these clippers, it is
better to leave the hair dry, not wet.
8. With the hair dry, it is much easier to
control the amount of hair being cut.
Beginning the haircut:
Cutting hair requires practice so it is always
better to leave the hair longer for the rst few
haircuts until you become used to the length to
which each comb attachment cuts the hair.
Comb Attachment (See Spare Parts Identication)
• Attachment comb #0.5 leaves 3mm (1/8
inch) hair length.
• Attachment comb #1 leaves 5mm (1/6 inch)
hair length.
• Attachment comb #2 leaves 7mm (1/4 inch)
hair length.
• Attachment comb #3 leaves 9mm (3/8 inch)
hair length.
Each comb attachment is marked accordingly
on its outside middle surface.
• To attach a comb, hold it with its teeth
upward and slide it onto and along the
clipper’s blade until the front of the comb
rmly seats against the clipper’s blade.
• To remove the comb, simply pull the comb
upward and away from the clipper’s blade.
• For even cutting, allow the comb
attachment/cutter to cut its way through
the hair.
• DO NOT force hair through quickly. Also
remember to comb the hair frequently
to remove trimmed hair and to check for
uneven strands.
Step 1 - Nape Of The Neck
1. Attach comb attachment 3mm or 6mm.
2. Hold the clipper’s cutting edge pointed
up and begin the haircut, starting at the
centre of the head at the base of the neck
(FIG.1)
3. Hold the clippers comfortably in your hand
and hold lightly against the head with the
comb teeth pointing upward. Gradually
and slowly lift the clippers, working
upwards and outwards, through the hair,
trimming just a little at a time.
4. As you cut, gradually lift the hair clippers
head towards you.
5. Continue to cut the back area from the
7
www.signaturebrand.co
bottom of the neck upwards to the top of
the ears.
Step 2 - Back Of The Head
1. Change to the next longest comb
attachment 9mm or 12mm and cut the
back of the head (FIG.2)
Step 3 - Side Of The Head
1. Change to one of the shorter combs
3mm or 6mm, trim sideburns, i.e. the hair
directly in front of the ears.
2. Then change to one of the longer combs,
9mm or 12mm, and continue to cut to the
top of the head (FIG.3)
Step 4 - Top Of The Head
1. Using comb attachment 9mm or 12mm
cut the hair on the top of the head from
back to front against the direction in which
the hair normally grows (FIG.4). In some
cases, this may require the reverse or
cutting from front to back.
2. Comb attachments 3mm or 6mm are
used for a close crew cut or short cut.
3. For longer hair on top, use the comb
provided and lift the hair on the top of the
head.
4. Cut over the comb with the hair lifted or
hold the hair between the ngers to lift
it and cut it to desired length (FIG.5&6).
Always work from the back of the head.
5. You can cut hair shorter gradually by
reducing the space between the comb,
ngers and the head. Comb out trimmed
hair and check for uneven strands.
Short Tapered Styles- “Flat Tops”
And Short Cuts
1. Starting with the longest attachment
comb 12mm cut from the back of the
neck to the crown. Hold the attachment
comb at against the head and slowly
move the clippers through the hair, as
shown (FIG.8).
2. Use the same procedure from the
lower side to upper side of the head, as
illustrated. Then cut the hair against the
direction in which it grows from the front
to the crown and then level the cut with
the sides.
3. To give a ‘at top’ look, the hair on top of
the head must be cut over the top of a at
comb rather than by using the attachment
comb.
4. Use the closer cutting attachment combs
to taper the hair down to the neckline as
desired.
5. Comb hair and check for uneven areas,
outlining sideboards and neckline as
describe previously (FIG.7).
FIG.1 FIG.2 FIG.3 FIG.4
FIG.5 FIG.6 FIG.7 FIG.8
8
SERVICE DEPARTMENT: +44 (0) 333 220 6062
Blade alignment
• Your clippers were carefully examined to
ensure that the blades were oiled and
aligned before leaving our factory.
• Blades must be realigned if they
have been removed for cleaning or
replacement.
• To realign the blades, simply match the
upper and bottom blades teeth up, point
for point. (End of top blade teeth should
be approximately 1.2mm back from
bottom blade.
• If the blade alignment is incorrect, add
a few drops of oil to the blades, turn the
clippers on for a few moments, then turn
off and unplug.
• Loosen the screws slightly and adjust,
tighten the screws after the blade is
aligned
Oil
• To maintain your clippers in peak
condition, the blades should be oiled after
every 3-4 times of use.
• ONLY use the correct oil to lubricate the
clippers
Power screw
• The power screw permits you to adjust
the power. It has been adjusted before
leaving the factory. However, if the voltage
in your home is low, you may need to
readjust it.
• To adjust, use a screwdriver to turn power
screw in a clockwise direction until the
arm strikes the coil, making a noise. Then
slowly turn power screw out (counter-
clockwise) just until noise stops. This is
now at the maximum power setting.
Blade lever
• The lever is
conveniently located
near your thumb (if
you are right handed)
so it can easily be
adjusted while the
clippers are in your hand.
• The lever adds versatility to your clippers
by allowing you to gradually change
the closeness of your cut without an
attachment comb.
• When the lever is in the upper most
position, the blades will give you the
closest cut and leave the hair very short.
• Pushing the lever downward gradually
increases the cutting length.
• In its lowest position, the lever will leave
the hair approximately the same length as
a No1 comb.
• The lever will also extend the use of your
blades since different cutting edge is used
in each setting.
• In addition, if extremely heavy hair cutting
has jammed the blades, it will help you
remove hair that has become wedged
between the two blades without removing
the blades.
1.2mm
9
www.signaturebrand.co
• While the clippers are running, rapidly
move the lever from ‘close cut’ to ‘longer
cut’ a couple of times. Doing this each
time after you have nished using your
clippers helps to keep the blades clear of
cut hair. If your clippers stop cutting and
this does not help, this would indicate that
your cutting blades are dulled, replace
them with new blades
Shaver
Charging instructions
1. Make sure shaver switch is turned to OFF.
2. Attach the charging cable to the bottom
of the shaver, then connect to a 2 pin
adaptor plug (NOT INCLUDED).
3. Plug the charger into an electrical outlet
and switch on at the wall socket.
4. Once plugged in, the LED charger light on
the front of shaver housing will activate.
5. Charging time is 8-16 hours, do not
exceed 20 hours.
6. Ensure that the shaver is totally drained of
power before charging again.
7. The shaver can be used for approximately
7 days after the battery has been fully
charged.
Operating instructions
1. Once fully charged, switch off at the wall
socket and unplug.
2. Remove charger cord from shaver
housing.
3. Remove shaver cover and switch to ON.
4. Gently guide shaver along face and chin
to remove facial hair using short, back
and forth strokes. Note: Do not apply too
much pressure while shaving.
5. If you have not used an electric shaver
before, your skin may become irritated
after use. This is a natural reaction that
may last for a few days until your skin
adjusts the shaver.
6. When you have nished shaving, switch
OFF.
How to use the sideburn trimmer
1. Push the lever on the back of the shaver
to release the side burn trimmer.
2. Softly touch your skin at a right-angle
direction with the trimmer and trim slowly.
3. After using, push down the switch.
How to use the trimmer
1. Ensure that you have placed 1 x 1.5V AA
Battery into the battery compartment.
2. To attach either the nose trimmer or beard
trimmer attachment, place it over the
motor spindle and turn clockwise to locate
and lock.
3. To remove the attachment turn
anticlockwise.
4. Keep the motor and the battery dry at all
times as failure to do so may result in the
product malfunctioning.
5. Dry the blades completely before
replacing.
10
SERVICE DEPARTMENT: +44 (0) 333 220 6062
Cleaning And Care
Warning! Only clean when shaver is
disconnected from charger and ensure that the
switch is turned to OFF.
• After each use beard
and hair cuttings may
collect in foil. Clean
foil by pressing the
cover lock button.
This will release the
cover enabling you to brush out the hair
that has been collected. Take care not
to disturb the blades as these are very
delicate.
• If necessary, use brush to clean hair
trimmings from exposed shaver cutting
heads.
• Recharge if necessary.
• To clean the trimmer unit, take the
attachment off as directed and run under
warm water.
• Make sure that the attachment is dried
thoroughly before storing or reattaching to
the trimmer.
• Wipe all external surfaces of power units
with a soft damp cloth.
Clippers:
• Switch the appliance off, unplug from the
mains.
• Wipe over the casing using a soft damp
cloth( If necessary a little washing up liquid
may be used) Do not immerse the unit in
water or and other liquid.
• Remove and wash the guards in warm
soapy water.
• Ensure all parts are dried thoroughly with
a soft towel before reusing.
• Do not use harsh abrasives or cleaners.
• Use the supplied brush to clean the
clipper blades after each use.
• Oil the clipper blades after every 3 or so
uses.
PLEASE NOTE:
• DO NOT press the foils.
• DO NOT open the foils with a screw driver.
• DO NOT use running water to clean the
shaver.
• DO NOT charge or store near a re or
heater, direct sunlight, or in vehicle during
warm weather.
Press
WARNING:
DO NOT IMMERSE ANY PART OF THE
APPLIANCE IN WATER
11
www.signaturebrand.co
DISPOSAL OF THE UNIT
Appliances bearing the symbol shown here
may not be disposed of in domestic rubbish.
You are required to dispose of old electrical
and electronic appliances like this separately.
Please visit www.recycle-more.co.uk or
www.recyclenow.co.uk
for access to information about the recycling
of electrical items.
Please visit www.weeeireland.ie for access to
information about the recycling of electrical
items purchased in Ireland.
The WEEE directive, introduced in August
2006, states that all electrical items must be
recycled, rather than taken to landll.
Please arrange to take this appliance to your
local Civic Amenity site for recycling, once it
has reached the end of its life.
NOTES
We hope you enjoy your appliance for many years.
As a thank you for purchasing one of our fantastic products,
we are giving you an extra 1 year peace of mind.
To receive your extra 1 year guarantee, register your appliance online by visiting
www.signaturebrand.co
Should you have a problem
with your appliance or need any spare parts please call our
Service Department on:
+44 (0) 333 220 6062
Distributed throughout the UK by RKW LTD
0516.V3
/