Sanyo czp6040 User manual

Brand: Sanyo

Model: czp6040

Type: User manual

This manual is also suitable for

Sanyo czp6040 is a 20" compact color TV with a 90-degree deflection angle picture tube and a convergence-free tube system. The instant-start feature provides instant picture and sound in standby mode, and the automatic fine tuning (AFT) ensures optimal picture quality. The TV has a variety of inputs, including an aerial input, a video input, and an audio input. The TV also has a built-in speaker, providing 3 watts of audio output with 10% distortion. The TV's dimensions are 590mm in width, 427mm in height, and 460mm in depth, and it weighs 21 kg.

Sqjilmlo

A WORLD OF EXPERIENCE

CZP 3040

CZP 3045

CZP 6040

CZP 6045

COLOUR TELEVISION

SERVICE MANUAL

P.Il. CHASSIS SERIES

iii

CONTENTS

SAFE~PRECAUTIONS ..........................................................................................

SPECIFICATIONS AND Summaries ......................................................................

BLOCK DIAGRAMS .................................................................................................

DISASSEMBLY. . . ....... . . .. . . .. ...... . .... . .... ........ .... .......... ..... . . .... . .. .

SERVICE ADJUSTMENTS .......................................................................................

REMOTE CONTROL PARTS LIST ............................................................................

PURITYAND CONVERGENCE ADJUSTMENTS ......................................................

Cabinet PARTS LISTS ...........................................................................................

TUNER CIRCUIT DIAGRAM ....................................................................................

SAFETY Electrical PARTS LIST .........................................................................

CIRCUIT DIAGRAMS ..............................................................................................

SAFETY PRECAUTIONS

2—5

6—9

10—13

14—16

17—18

19—22

Inside Back Cover

1. An isolation transformer should be connected in 3. When replacing a chassis in the cabinet, always

the power line between the receiver and the AC be certain that all the protective devices are

line when servicing circuitry on the primary side

installed properly, such as, control knobs,

of the converter transformer of the set.

adjustment covers or shields, barriers, isolation

2. Comply with all caution and safety-related notes

resistor-capacitor networks etc.

provided on cabinet back, inside the cabinet, on Before returning any television to the customer,

the chassis or the picture tube. the service technician must be sure that it is

completely safe to operate without danger of

electrical shock.

X-RADIATION PRECAUTION

The primary source of X-RADIATION in television receiver is the picture tube. The picture tube is specially

constructed to limit X-RADIATION emissions. For continued X-RADIATION protection, the replacement tube

must be the same type as the original including suffix letter. Excessive high voltage may produce potentially

hazardous X-RADIATION. To avoid such hazards, the high voltage must be maintained within specified limit.

Refer to this service manual high voltage adjustment for specific high voltage limit. If high voltage exceeds

specified limits, take necessary corrective action. Carefully follow the instructions for +Bl volt power supply

adjustment, and high voltage adjustment to maintain the high voltage within the specified limits.

PRODUCT SAFETY NOTICE

Product safety should be considered when a component replacement is made in any area of a receiver.

Components indicated by mark ~ on the schematic diagram designate components where safety can be of

special significance. It is particularly recommended that only parts designated in the parts list be used for the

replacement of components designated by mark ~ . No deviations from resistance wattage or voltage ratings

may be made for replacement items designated by mark

SPECIFICATIONS CZP 3040

Power source

I AC230V, 50Hz

Audio output

1.5W, 10°/0distortion

Power consumption I 47W

I Speaker I 8x8cm, 160hm

Television system

System-B/G

Colour system

PAL

Channel coverage

VHF

1—11

UHF

21 — 69

Aerial input

impedance 75 ohms

Intermediate

Frequencies Video 38.9 MHz

Sound 33.4 MHZ

Colour 34.47 MHZ

Picture tube

34cm diagonal, 90 degree

Type No. 370LHB22

I Hiah voltage

I 25kV at Zero beam

Semiconductors

Dimensions

8 Transistors

4 Ics

Width 463mm

Height 335mm

Depth 370mm

Weight

llkg

SUMMARY

14” COMPACT COLOUR TV

All solid state circuitry for stable quality, less power

consumption and high reliability. Simplified chassis

construction with 1 main circuit board for easy

access and servicing. In-1ine gun, slotted mask

black matrix picture tube with 90° deflection angle.

Convergence-free tube system.

CZP 3040

Instant-Start for instant picture an-d sound in

standby mode. With Automatic Fine Tuning (AFT).

CHANNEL SELECTOR BUTTON

“<\

—

—TUNING BLOCK

—ADAPTOR KNOB

—AFT (AUTOMATIC FINE TUNING)

‘~

POWER SWITCH

—-VOLUME

SPECIFICATIONS CZP 3045

Power source

Power consumption

AC230V, 50Hz

Audio output

I 1.5W, 10°/0distortion

S@eaker

I 8@cm, 16 ohm

50W

Television system

System-B/G

Picture tube

34cm diagonal, 90 degree

Type No. 370 LHB22

Colour system

Channel coverage

Aerial input

impedance

Intermediate

Frequencies

PAL

High voltage

25kV at Zero beam

Semiconductors

16 Transistors

8 ICS

Dimensions

Width

463m m

Height 335mm

Depth 370mm

Weiaht

llka

VHF

1—11

UHF

21 — 69

75 ohms

Video 38.9MHz

Sound

33.4 MHZ

Colour

34.47 MHZ

SUMMARY CZP 3045

14” COMPACT COLOUR TV

Instant-Start for instant picture and sound in standby

All solid state circuitry for stable quality, less power

mode, With Automatic Fine Tuning (AFT).

consumption and high reliability. Simplified chassis With 6 functions infra-red remote control.

construction with 1 main circuit board for easy

access and servicing. In-1ine gun, slotted mask

black matrix picture tube with 90° deflection angle.

Convergence-free tube system.

Transducer

Programme Indicator

Standby Indicator

Programme Selector

(–, +)

_ Programme

Selector

– Volume

_ Power ON/OFF

Switch

-Sound Mute

b-a

f==

II 1/

Power Switch

Volume (–, +

(on/off)

— AFT

— ADAPTOR

-TIE --

SPECIFICATIONS CZP 6040

Power source

AC 230V, 50Hz

Power consumption 67W

Television system

System-B/G

Colour system

PAL

Channel coverage

VHF

1—11

UHF

21 — 69

Aerial input

impedance 75 ohms

Intermediate

Frequencies Video

38.9 MHz

Sound 33.4 MHZ

Colour

34.47 MHZ

Audio output 3.OW, 10°/0distortion

Speaker

8x 12cm, 160hm

Picture tube

48cm diagonal, 90 degree

Type No. 510XAB22

High voltage

27kV at Zero beam

Semiconductors 8 Transistors

4 Ics

Dimensions Width 590mm

Height

427mm

Depth 460mm

Weight 21kg

SUMMARY CZP 6040

20”

COMPACT COLOUR TV

instant-Starl for instant picture and sound in standby -

All solid state circuitry for stable quality, less power

mode, With Automatic Fine Tuning (AFT),

consumption and high reliability. Simplified chassis

construction with 1 main circuit board for easy

access and servicing. In-1ine gun, slotted mask

black matrix picture tube with 90° deflection angle.

Convergence-free tube system,

IIL

PROGRAMME SELECTOR BUTTON

,—AFT

(Automatic Fine Tuning)

~POWER SWITCH

~VOLUME

SPECIFICATIONS CZP 6045

Power source AC230V, 50Hz

Power consumption 70W

Television system

System-B/G

Colour system PAL

Channel coverage VHF 1—11

UHF 21 — 69

Aerial input

impedance

75 ohms

Intermediate

Frequencies Video

38.9MHz

Sound 33.4 MHZ

Colour 34.47 MHZ

Audio output

3.OW, 10°/0distortion

Speaker 8x12cm,160hm

Picture tube 48cm diagonal, 90 degree

Type No. 51OXAB22

High voltage 27kV at Zero beam

Semiconductors 17 Transistors

8 ICS

Dimensions Width

590mm

Height 427mm

Depth 460mm

Weight 21kg

SUMMARY CZP 6045

21“ COMPACT COLOUR TV

Instant-Start for instant picture and sound in

All solid state circuitry for stable quality, less power

standby mode. With Automatic Fine Tuning (AFT).

consumption and high reliability. Simplified chassis

12 programmed can be automatically found by the

construction with 1 main circuit board for easy

search-tuning system and stores them in the

access and servicing. In-1ine gun, slotted mask

electronic memory.

black matrix picture tube with 90° deflection angle.

With 6 functions infra-red remote control.

Convergence-free tube system.

lIkcudt-

/ “’;

‘aIF_

/l_e

.&...’&” ~ / 8

Programme Indicator

~ Maim ON/OFF Switch

Standby Indicator

A Volume

Programme Selector Button

AFT Switch

Tuning Preset Button

Slow Button

Fast Button

Band Button

Band Indicator

AFT Defeat Button

@ Colour

<$ Brightness

~ Contrast

AERIAL

BRIGf-fTNESs

cOLOUR

sut3-

BR16HTNES ‘

vIDEO , COWR

4DEfLECW0N

& I-IJE

DRIVE

BLLJE

BIAS

VIF 8 .SIF

RF-AGC ._,

CONTtiST;

REDOU~WT

Q611

RED

DRIVE

RED

OIAS

~g:,EN ouTPur

::A;EN

2-4-

1 --f---l’

VIDEO

BuFFER

At’l?

ADJ,

)

- 16

lJw&lP. 5 ~

AFT

13 -

A 6C

‘T3 (

PUSH

TOUCti

uNIT

1“ I

B-y

_ R-f

142

vOLUME

lH DELAY

LINE

--d

t-u

vERT.

PEF1.ECTIO~

S/WKER g———————

AUDIO A~P-

CONVERTER

I i-----

—-———

IL-J

“-l

SCREEN I

FOCUS

P} ‘

TRANS. ,

+-3

HORIZ.

HORI Z.

DRIvE OUTPUT

Q431

Q432

MAIN

SWITCH

l—____—_. J

Bbl

AERIAL

t“~”‘t

REMOTE

MAIN (

5WI TCH -

AC 23W

Wttz

i’

(

--A

h ~

EWFER

0151

vIDEO,COWi?

0EfEL7foN

AtIf?

ADJ.

LINE

AUDIO ~P-

~J.p’f-

Q303

g- ,—-63 (130V)

Ie-B’’’’”v)

64 G?4V)

lr--

VERT.

DEFLECTION

F#L: OUTPUT

13LuE

DRIVE

Q611

RED

t)RIVE

;~~&EN

’24

I— __

—- —-- __

FOCWS

1~1

FLYB~ /

TRANS ,

——— —.

--!

AERIAL

‘3;

PLASH ;

l--;n —

MAIN

5WI rcH -

AC 230V

5oHz

BRl(iI ITNES5

L.(

(

SUB-

f3R16}lTlI@ ‘

vIDEO, COWR

4DEFLEC110N

RF-AGC .==

CON’117/t5T

-–d-l’ I

VIDEO

vOLUME

LINE

80v)

30V)

‘f

L*”

m=.

. . .

———

I r------------

—

l–_–––_J. J

(

——

—.—

AERIAL

h’

BRIWTNESS

—..

CONT”IVIST

suEi-

vIDEO

BR16H1-tdES

BuFFER

Q151

vIDEO , COLWR

*1#-

4DE?LEL1ION

ADJ,

~~-]

?()

?3 -

-n-

KEY804RP ‘

UNIT

.E1 : ‘

v/s

UNIT

-—

GREEN !

BIAS

D. Y’.

----

VOLUPIE

1 —------=

2 ----- ----~ =f—

G -~

.~ -- -- --—-––-

4 —-_-_Qj~-Q&j

VIDEO fl vISE

1; 1..-—L+

- ,. ,.

11{DEMY

—

LINE

L-

2 IC171

I[:44 I 2 —-–--——

vERT.

PEFLH; i 10ti

AUDIO ~~11’

~B3 (180v)

I I

I I I

MAIN

Ii!

5WITCH -

23W

!wfiz

— M (24 v)

02 (23

B5(15v)

-n

B6 w)

RE&JRATOR

1C361

—-

E---gg-

-1

;L.

l—_— —_ —--J

DISASSEMBLY CZP 3040

SCREkV-A

1. BACK COVER REMOVAL

—

1. Remove removing 4 screws (A).

—J

“

II\

2. Release 2 Hook (A) shown in figure (1).

. / 3. Take off ANT Terminal and back cover.

mffml

r,1!

“

-(ANT

- Pull

2. TUNING ASSY BOARD REMOVAL

\u’

1. Take off knobs of front control.

Pull -

Bfizn

—

2. Remove 2 screws (B).

3. Then draw out the power switch.

4. Remove 3 screws (C) and release hook B, Guide pin.

Hook (A)

Then draw out the tuning Assy’ board. figure (1)

---HOOK (a

)

(B)

5)-+

TERMINAL)

3. PICTURE TUBE REMOVAL

Caution: Do not disturb the deflection yoke or

magnet assembly on CRT neck.

Care must be taken to keep these

assemblies intack.

Discharge picture tube by shorting the

anode connection to chassis ground. (Not

cabinet or other mounting parts).

Remove the cabinet back and chassis.

Place the cabinet face down on a soft surface.

Remove 4 screws (D).

Gently lift out the picture tube and place it on a soft

surface.

Install replacement picture tube in reverse order.

DISASSEMBLY CZP 3045

SCREW-A

1. BACK COVER REMOVAL

1. Remove removing 4 screws (A).

2. Release 2 Hook (A) shown in figure (1).

3. Take off ANT Terminal and back cover.

2. TUNING UNIT& RC UNIT REMOVAL

1. Remove 3 screws (B) (on Tuning Board).

2. Release 2 Hook (B) shown in figure (2).

3. Take out Tuning unit & RC unit.

SCREWS

(B)

Pull -

TERMINAL)

Hook (A) ~

figure (1)

1 4

L \k–,

draw out

figure (2)

draw out

SCREWS (C)

3. PICTURE TUBE REMOVAL

Caution:

Do not disturb the deflection yoke or

magnet assembly on CRT neck.

Care must be taken to keep these

assemblies intack.

Discharge picture tube by shorting the

anode connection to chassis ground. (Not

cabinet or other mountina Darts).

Remove the cabinet back and ch;ssis. ‘

Place the cabinet face down on a soft surface.

Remove 4 screws (C).

Gently lift out the picture tube and place it on a soft

surface.

Install replacement picture tube in reverse order.

DISASSEMBLY CZP 6040

BACK CABINET REMOVAL

1. Unhook the AC cord at hook (A).

2. Remove 4 screws (A).

3. Then take off the back cabinet.

T-L=sy-

1. Take off knobs of front control.

SCREWS (A)

2. Remove 4 screws (B) and release hook (B).

—HOOK (B) 3. Then draw out the tuning Assy’ board.

SCREWS (B)

—

PICTURE TUBE REMOVAL

—

Caution: Do not disturb the deflection yoke or magnet

assembly on CRT neck.

Care must be taken to keep these assemblies

intact.

Discharge picture tube by shorting the anode

connection to chassis ground. (Not cabinet

or other mounting parts).

1. Remove the cabinet back and chassis.

2. Place the cabinet face down on a soft surface.

3. Remove 4 screws (C).

4. Gently lift out the picture tube and place it on a soft

surface.

5. Install replacement picture tube in reverse order.

‘w

‘Y@

SCREWS

(c)

DISASSEMBLY CZP 6045

SCR-EWS (A)

V/S BOARD REMOVAL

1. Disconnect mini connectors on V/S board.

2. Remove 2 hooks.

3. Then draw out th is board.

CONTROL BRACKET REMOVAL

1. Remove 3 screws (B).

2. Remove a hook (B).

3. Then draw out this bracket.

HOOK (B)

SCREWS (B)

PICTURE TUBE REMOVAL

e. I

Caution: Do not disturb the deflection yoke or magnet

assembly on CRT neck.

Care must be taken to keep these assemblies

intact.

@iiiii4!&.... 1.

‘\

‘b

Discharge picture tube by shorting the anode

connection to chassis ground. (Not cabinet

or other mounting parts).

Remove the cabinet back and chassis.

‘yf

2. Place the cabinet face down on a soft surface.

3. Remove 4 screws (C).

4. Gently lift out the picture tube and place it on a soft

surface.

5. Install replacement picture tube in reverse order.

SCREWS (Cl

ADJUSTMENTS

DamFing

100

ohm

VI F

SWEEPIMARKER

GENERATOR

“TP-D1” “TP-D2”

DC POWER

CONNECTION

SUPPLY

Main Unit

m’

L151

15.5V

“:0 0::

“KH-8”

INPUT OUTPUT

4–6V

4 “TP-C”

Matching pad

o.OlpF

●“TU-TP”

lK ohm b

A..

*“L151 –a side”

10K ohm

- --’’0101 – collector”

item 1. 1st waveform

2. overall waveform

DC 15.5V KH-8

KH-8

DC4—6V TP-C

Output probe

TP-C

TU-TP

Input probe L151 — a side

L151 — a side

Matching pad

b side

Damping

Not used

Connect (TP-DI – D2)

Adjust T131 for maximum

Adjust tuner converter on

response at 38.9 Hz,

tuner and L101 to obtain

ADJUSTMENTS

proper shape waveform as

figure.

VIF

WAVEFORM

38.9 MHz

MHz

31.9 MHZ

AFT

Receive an active station.

Adjust T141 to obtain best picture.

+6 POWER SUPPLYAFT

Receive colour bar pattern.

Connect volt-meter to test point TP-B.

Set’s controls: bright .................min.

colour..,,., ....... norm.

contrast ...............min.

Adjust VR321 for +131 *1 .OV.

AGC

Receive clearest station.

Rotate VR101 fully clockwise and then rotate it

anticlockwise slowly until the snow just dis-

appears.

VIDEO SIGNAL

Receive colour bar pattern.

Connect oscilloscope to test point TP-F.

Adjust VR140 for l. OVp-p as shown in Figure-1.

Fig-1 (H)

COLOUR

Receive colour bar pattern.

Set’s controls: bright ................max.

colour ............. norm.

contrast, ............. max.

Connect oscilloscope to test point TP-6B.

[1] lH Delay Line

Adjust VR251 for minimum amplitude of “A” as

shown in Figure-2.

Adjust T281 to obtain each 1H waveform

(Amplitude) as shown in Figure-3.

[2] APC

Adjust L241 for maximum amplitude of “B” as

shown in Figure-2.

Fig-2 (Vert.)

I—H-I—l”+

------ ------ -

T_lL(N

-------------

-----------

GREY SCALE TRACKING

Receive B/W circular pattern.

Set’s controls: bright ................max.

contrast .............. max.

Change service tip from KSV-1 to KSV-2.

Drive controls: red (VR612) ........mid range

blue (VR602) ,..... mid range

Bias controls: red (VR611) min.

green (VR621), .....min.

blue (VR601) ........min.

Adjust screen control to obtain just visible one

coloured line.

Advance each bias control to obtain just visible

three coloured line (white line).

Change service tip from KSV-2 to KSV-1.

Adjust red and blue drive controls alternately to

produce normal black and white picture.

Check for proper grey scale tracking at all

brightness levels.

SUB-BRIGHTNESS

Receive B/W circular pattern.

Set’s controls: bright ................max.

colour .....min........min.

contrast ...............min.

Connect volt-meter between tests points (TP-G

(–) and TP-H (+).

Adjust VR21 Ofor 0.07V. CZP 3040/3045.

Adjust VR21 Ofor 0.30V. CZP 6040/6045.

HIGH-VOLTAGE AND HORIZ. WIDTH ADJUST-

MENT

NOTE: +6 power supply, AGC and grey scale

should be adjusted before attempting this

adjustment.

Receive circular pattern.

Set’s controls: bright max.

colour ................min.

contrast.,., .......... max.

Connect high-voltage meter to anode on picture

tube.

Check picture width and high-voltage.

If picture is too wide or narrow, or high-voltage is

not:

(1) 22kV *1 kV when the voltage between tests

points “TP-G” and “TP-H” is 0.7V, cut or short

the lead (J41 3), for CZP 3040/3045.

(2) 24kV *1 .OkV when the voltage between tests

points “TP-G” and “TP-H” is 0.9V, cut or short

the lead (J41 3), for CZP 6040/6045.

I HIGH-VOLTAGE IH-WIDTH I

CUT up (approx. 0.5kV)

decrease

SHORT down (approx. 0.5kV) increase

Remarks: This adjustment affects sub-brightness.

Therefore, recheck sub-brightness ad-

justment.

VERTICAL SIZE

Adjust VR450 to obtain proper picture.

Fig-3 (Ho:.)

HORIZONTAL CENTRE

Adjust VR421 to obtain proper picture,

VERTICAL CENTRING ADJUSTMENT

Vertical centring can be adjusted by connecting

vertical tip to anyone of three terminals on CZP

6040/6045.

SOUND NORMALIZATION CZP 3045

1. Tune the receiver to an active station.

2. Set sound volume to pre-set position by

turning T.V. set on. (In case the receiver is on

position, turn the receiver off then turn it on).

NOTE: Do not press the sound volume up/down

(+, -) buttons on T.V. receiver or remote

control transmitter during this adjustment.

3. Adjust VR711 to proper sound volume.

VR711

IC701

Fig.4RCBIJARi)

REMOTE CONTROL RC344 PARTS LIST

-TE -run.

SOUND NORMALIZATION CZP 6045

Receive an active station.

Set sound volume to pre-set position to turning

T.V. set on. (In case the receiver is on position, turn

the receiver off then turn it on).

NOTE: Do not press the sound volume up/down

(+, -) buttons on T.V. receiver or remote

control transmitter during this adjustment.

Adjust VR790 to proper sound volume.

IC770

VR790

[

IC71O

Figure4 Vl~BOARD

FOCUS ADJUSTMENT

Adjust focus control on the right side of the chassis

for well defined scanning lines.

Key

Part No.

Description

PURITY AND CONVERGENCE ADJUSTMENTS

CAUTION: Convergence and Purity havebeenfactory aligned. Do not attempt to tamper with these alignments. However, the

effects of adjacent receiver components, or replace picture tube or deflection yoke may require the need to readjust purity

and convergence. If adjustment is required the adjustments should be made in the following sequence.

PURITY ADJUSTMENT

1, Place the picture tube face north or south and

demagnetize the picture tube and receiver using an

external degausing coil. When replacing picture tube or

deflection yoke, mount deflection yoke and purity-

convergence magnetes assembly properly, see figure 1.

2. Turn Red and Blue guns off to provide only Green raster

by rotating Red and Blue Bias controls fully counter-

clockwise. Slowly rotate Green Bias control clockwise

to produce Green raster.

3. Loosen the screw holding the Deflection Yoke and slide

th eDeflection Yoke backward as far as possible, and

remove the 3 D.Y. spacers.

4. Rotate the spread the Tabs of the two Purity Magnets to

centre the vertical green belt in the picture screen.

D.Y. SPACERS

The Purity Magnets are also adjusted toobtain vertical

centering of the raster.

5. Slowly slide the Deflection Yoke forward until a uniform

green screen is obtained.

6. Check the purity of the red and blue screens for

uniformity, turn off other colours to check this (use bias

controls). Readjust the yoke position if necessary until

all screens are pure.

7. Adjust each Bias control and screen control to obtain

white raster. Refer to Gray Scale Adjustment. If part of

the picture screen is coloured, adjust the Deflection

Yoke position forward or backward slightly.

8. Fasten the screw of the Deflection Yoke. Adjust

Convergence next.

~!lJ

PURITY MAGNET

FOUR-POLE

Y/\

MAGNET TABS /’\\K

DEFLECTION YOKE

MOUNTING SCREW

J //

SIX-POLE

Figure 1- PURITY AND CONVERGENCE MAGNETS

CONVERGENCE ADJUSTMENT

1. Usea dot-crosshatch pattern signal.

3. Keeping the mutual angle of the Tabs of the Four Pole

2. Turn Red and Blue guns on and turn off Green gun,

Magnet turn them together to superimpose the Blue and

refer to Purity Adjustment step 2. Adjust the angle

Red horizontal lines in the centre area of the picture

between the Tabs of the Four Pole Magnet 1 and2, and

screen. Refer to figure2.

superimpose the Red and Blue vertical lines in the centre

4. Turn

Green qunon and adjust six Pole Magnet 3and4

spread

area of the picture screen. Refer to figure2.

Constant

“~

+/-j eotae

——————- L___ --------

I Adjust tabstogetherto

7 superimposeredandblue

~ I horizontal line.

(p&J4EDt

(or narrow)

)

Adjust tabs’angle to superimpose

blue and red vertical line

spread (or narrow)

/==

Figure 2- BLUE AND RED LINE MOVEMENT

OUTER AREA CONVERGENCE

If mis-convergence on the outer area exits, asfollow

so that the ‘Green line superimposes on tie Red/Blue

lines. This is the same rxocedure used in stem 2 and 3.

Refer to f[gure 3,

=3=

+k-4RE+

Adjust tabs angle to superimpose

red/blue and green vertical line.

Constant

Rotate

Adjust tabs together to

superimpose red/blue and

green horizontal line.

Figure 3- BLUE/RED AND GREEN LINE MOVEMENT

adjustment.

I %’i‘? I

Deflection

“

Yoke

.%ing the Deflection Yoke the - direcxion, Red/Blue lines on the screen move the -direction.

Swing the Deflection Yoke the <>direction, Red/Blue lines on the screen move the.>] airection.

5LUE

,LUEE43.=

““IIz : ‘1””

I RED

GREEN

BLUE

Swing the Deflection Yoke the o airemion, Red/Blue iines on the screen move the -direction.

Swing the Deflection Yoke the .:> direction, Red/Blue lines on the screen move the<:> direction.

To fasten the Deflection Yoke, Insert and fix the D.Y. spacer.

CABINET PARTS LIST CZP 3040

NOTE: Parts order must contain Service Ref. No,, Key No., Part No., and Description.

Key

No.

‘1,

kiss ~11/ 14$9-’

12 11 10

9 15

Part

Description

Key

Part

No.

Description

YPO1979

3102651

ETOO08

3MO0745

3MO0295C

KBO023B

K2132

3101346

3M05178

Escutcheon Ass’y

Cabinet

Rod Aerial (2 used)

Aerial Base

Small Knob (3 used)

Button, AFT

Button, Prog. Main (9 used)

AC Cord Holder

Front Panel

10.

11.

12.

13.

14.

15.

16.

17.

3102511A

3MO0119

3MO1O22

3MO0891

3S00732

2PO0327

3101317

317432

Slide Knob, Vol.

Adaptor Knob

Door

Front Panel Dec. Plate

Indicator Plate

Sanyo Badge

Foot (2 used)

Hinge (2 used)

●

Page is loading ...

Sanyo czp6040 User manual

Brand: Sanyo

Model: czp6040

Type: User manual

This manual is also suitable for

Download PDF

report

Sanyo czp6040 User manual

This manual is also suitable for

Sanyo czp6040 User manual

Related papers

Other documents