Raymarine SportPilot Owner's Handbook Manual

Brand: Raymarine

Model: SportPilot

Category: Navigators

Type: Owner's Handbook Manual

This manual is also suitable for

SportPilot Plus

SportPilot and

SportPilot Plus

Owner’s

Handbook

Document number: 81057-6

Date: February 2006

81057_6.book Page i Tuesday, February 21, 2006 2:21 PM

ii SportPilot and SportPilot Plus - Owner’s Handbook

Autohelm, HSB (High Speed Bus), SailPilot, SeaTalk and SportPilot are registered

trademarks of Raymarine UK Ltd.

Raymarine, AST (Advanced Steering Technology), AutoAdapt, AutoLearn,

AutoRelease, AutoSeastate, AutoTack, AutoTrim, FastTrim, GyroPlus, RayGyro,

RayPilot and WindTrim are trademarks of Raymarine UK Ltd.

Handbook contents © Raymarine UK Ltd.

81057_6.book Page ii Tuesday, February 21, 2006 2:21 PM

Preface iii

Contents

Chapter 1: Introduction ............................................................1

About this handbook ......................................................................3

Important Information ....................................................................3

Chapter 2: Operating the SportPilot .......................................7

2.1 Switching on and off ....................................................................... 7

Switching on ...................................................................................7

Switching off .................................................................................. 7

2.2 Basic operation ...............................................................................7

Engaging and disengaging the pilot ............................................... 7

Making course changes ..................................................................8

Adjusting autopilot gain .................................................................9

2.3 Using Navigator (Track) mode ......................................................10

Chapter 3: Maintenance & Fault Finding ..............................13

3.1 General maintenance ...................................................................13

3.2 Fault finding .................................................................................14

3.3 Product support ............................................................................14

Chapter 4: Installing the SportPilot ......................................15

4.1 Planning the installation ...............................................................16

Installation instructions ................................................................17

4.2 Installing the compass ..................................................................19

Compass location .........................................................................19

Compass mounting ......................................................................20

Compass cabling ..........................................................................20

4.3 Installing the rudder position sensor – optional ............................22

Linear rudder position sensor – installation (hydraulic outboard

steering systems) ..........................................................................22

Rotary rudder position sensor – installation (hydraulic inboard steer-

ing systems) ..................................................................................25

4.4 Providing power for the SportPilot ................................................34

Interfacing with NMEA equipment ...............................................35

4.5 Connecting SeaTalk equipment ....................................................36

Typical SeaTalk connections ..........................................................37

4.6 Installing the SportPilot ................................................................38

Step 1 – Remove the steering wheel .............................................38

Step 2 – Mount the torque bracket ...............................................39

Step 3 – Plug the cables into the SportPilot ...................................42

Step 4 – Assemble and secure the SportPilot ................................43

81057_6.book Page iii Tuesday, February 21, 2006 2:21 PM

iv SportPilot and SportPilot Plus - Owner’s Handbook

Chapter 5: Compass Calibration ............................................49

Important note ..............................................................................49

Introduction ..................................................................................49

5.1 Compass linearization and heading alignment .............................50

5.2 Heading alignment without linearizing .........................................51

81057_6.book Page iv Tuesday, February 21, 2006 2:21 PM

Chapter 1: Introduction 1

Chapter 1: Introduction

Congratulations on the purchase of your Raymarine SportPilot.

The SportPilot fits neatly over the steering column directly behind the steering

wheel. All of the autopilot controls are located on a rotary switch at the end of a

control stalk. These controls consist of:

• Standby mode (

STANDBY)

• five autopilot settings (

LO to HI) to control the amount of rudder applied

when course changes are made

• Navigator (or Track) mode (

NAV) for tracking to waypoints when the SportPi-

lot is used with a chartplotter or GPS

The SportPilot is very easy to use:

• simply point the boat in the direction you want to go, turn the rotary control

switch to one of the autopilot settings (

LO to HI) and release the wheel –

really is that simple

• if you want to change course under autopilot control, simply turn the boat

onto the new heading and once again let go of the wheel –

you don’t even

have to disengage the autopilot

If you have a SeaTalk or NMEA position sensor, navigation to favorite fishing

grounds or wrecks is a breeze. Cross track error information is constantly fed to

the autopilot so that your heading is continuously updated.

D1356-2

81057_6.book Page 1 Tuesday, February 21, 2006 2:21 PM

2 ST60 Tridata Instrument Owner’s Manual

The SportPilot can also be operated away from the steering station, using a hand-

held remote control or a Raymarine fixed control unit.

The SportPilot is designed to be owner installed, and most of the necessary tools

are supplied.

SportPilot and SportPilot Plus specifications

There are two versions of the SportPilot: the SportPilot and the SportPilot Plus. It

is vital to use the appropriate pilot for your boat. The SportPilot will not perform

effectively if you exceed the following boat compatibility specifications.

General specifications

Nominal supply voltage: 12 V DC

Dimensions: Height: 220 mm (8.7 in)

Width: 238.5 mm (9.4 in) including stalk

137.5 mm (5.4 in) excluding stalk

Depth: 100.5 mm (4.0 in)

Heading reference: Raymarine fluxgate compass

Operating modes: • Standby (autopilot not active)

• Auto (autopilot operating): with five settings to

control autopilot rudder gain.

• Navigation (Track) mode: autopilot following

waypoints received from navigator.

Inputs/Outputs: Compass, Rudder Position Sensor, Power/

NMEA 0183, SeaTalk

Steering shaft size:

19 mm (

in) and 25 mm (1in) tapered

SportPilot – boat compatibility

Maximum displacement: 2000 kg (4400 lbs) manual cable steering

3500 kg (7700 lbs) manual hydraulic steering

3500 kg (7700 lbs) servo hydraulic steering

Maximum wheel diameter:

(depending on weight)

54 cm (21 in) wooden

46 cm (18 in) metal

SportPilot Plus – boat compatibility

The SportPilot Plus has a more powerful motor designed specifically for boats

where the autopilot is used for hours at a time on a daily basis.

81057_6.book Page 2 Tuesday, February 21, 2006 2:21 PM

Chapter 1: Introduction 3

About this handbook

This handbook contains two main parts:

Part 1: Using the SportPilot

This part of the handbook explains how to use your SportPilot:

Part 2: Installing the SportPilot

This part of the handbook explains how to install your SportPilot:

Note:

This handbook contains important information about installing, using and main-

taining your new Raymarine product. To get the best from the product, please read this

handbook thoroughly.

Chapter 2:Operating the SportPilot

Explains how to use the SportPilot.

page 7

Chapter 3:Maintenance & Fault Finding

Provides maintenance and fault finding information.

page 13

Chapter 4:Installing the SportPilot

Explains how to install your SportPilot and its components.

page 15

Chapter 5:Compass Calibration

Explains how to linearize the SportPilot compass and align

its heading.

page 49

81057_6.book Page 3 Tuesday, February 21, 2006 2:21 PM

4 ST60 Tridata Instrument Owner’s Manual

Important information

Safety notices

WARNING: Product installation & operation

This equipment must be installed and operated in accordance

with the Raymarine instructions provided. Failure to do so could

result in personal injury, damage to your boat and/or poor product

performance.

WARNING: Electrical safety

Make sure you have switched off the power supply before you

start installing this product.

WARNING: Navigation aid

Although we have designed this product to be accurate and

reliable, many factors can affect its performance. Therefore, it

should serve only as an aid to navigation and should never replace

commonsense and navigational judgement. Always maintain a

permanent watch so you can respond to situations as they

develop.

Your Raymarine autopilot will add a new dimension to your boating enjoyment.

However, it is the skipper’s responsibility to ensure the safety of the boat at all

times by following these basic rules:

• Ensure that someone is present at the helm AT ALL TIMES, to take manual

control in an emergency.

• Make sure that all crew members know how to disengage the autopilot.

• Regularly check for other boats and any obstacles to navigation – no matter

how clear the sea may appear, a dangerous situation can develop rapidly.

• Maintain an accurate record of the boat’s position by using either a naviga-

tion aid or visual bearings.

• Maintain a continuous plot of your boat’s position on a current chart. Ensure

that the locked autopilot heading will steer the boat clear of all obstacles.

Make proper allowance for tidal set – the autopilot cannot.

Even when your autopilot is locked onto the desired track using a navigation aid,

always maintain a log and make regular positional plots. Navigation signals can

produce significant errors under some circumstances and the autopilot will not be

able to detect these errors.

81057_6.book Page 4 Tuesday, February 21, 2006 2:21 PM

Chapter 1: Introduction 5

EMC conformance

All Raymarine equipment and accessories are designed to the best industry

standards for use in the recreational marine environment.

The design and manufacture of Raymarine equipment and accessories conform to

the appropriate Electromagnetic Compatibility (EMC) standards, but correct

installation is required to ensure that performance is not compromised.

Waste from Electrical and Electronic Equipment

(WEEE) Directive

The Waste from Electrical and Electronic Equipment (WEEE) Directive requires the

recycling of waste electrical and electronic equipment. Whilst the WEEE Directive

does not apply to some of Raymarine’s products, we support its policy and ask you

to be aware of how to dispose of this product.

The crossed out wheelie bin symbol, illustrated above, and found on our products

signifies that this product should not be disposed of in general waste or landfill.

Please contact your local dealer, national distributor or Raymarine Technical

Services for information on product disposal.

Handbook information

To the best of our knowledge, the information in this handbook was correct when

it went to press. However, Raymarine cannot accept liability for any inaccuracies

or omissions it may contain. In addition, our policy of continuous product

improvement may change specifications without notice. Therefore, Raymarine

cannot accept liability for any differences between the product and the

handbook.

Warranty

To register your new Raymarine product, please take a few minutes to fill out the

warranty card. It is important that you complete the owner information and

return the card to us to receive full warranty benefits.

81057_6.book Page 5 Tuesday, February 21, 2006 2:21 PM

6 ST60 Tridata Instrument Owner’s Manual

81057_6.book Page 6 Tuesday, February 21, 2006 2:21 PM

Chapter 2: Operating the SportPilot 7

Chapter 2: Operating the SportPilot

2.1 Switching on and off

Switching on

The SportPilot enters Standby mode when the power supply is switched on. This

mode is identified by the flashing red

AUTO LED. As soon as the pilot is engaged

(see below), the red LED glows permanently to confirm this selection.

Switching off

Switching off your boat’s power supply will switch off the SportPilot. To prevent

the SportPilot draining the battery, always switch off the power

supply when leaving the boat for long periods.

2.2 Basic operation

Engaging and disengaging the pilot

Engaging the pilot

1. Steer the boat onto the required heading.

2. Turn the rotary control switch clockwise from

STANDBY to one of the five

autopilot gain settings (

LO to HI).

Note:

Note: It is important to select the correct gain setting for your boat’s speed. See

page 9 for details.

3. Release the wheel – there will be a short delay before the pilot takes control.

D1400-2

81057_6.book Page 7 Tuesday, February 21, 2006 2:21 PM

8 ST60 Tridata Instrument Owner’s Manual

Disengaging the pilot

You can disengage the SportPilot at any time by turning the rotary control switch

STANDBY.

Making course changes

Large course changes

When your boat is under autopilot control, you can override the pilot at any time

by steering the wheel in the normal way.

As soon as you release the wheel, the SportPilot automatically regains control to

maintain the boat’s current heading.

CAUTION:

You MUST center the helm after making large course changes. If

you do not center the helm, the autopilot could become unstable

or take a long time to settle onto the required heading.

Minor course changes

When your boat is under autopilot control, you can make minor course

adjustments in 1° increments by pressing the:

• -1° (Port) or

• +1° (Starboard) switches on top of the control stalk

Note:

You can also make course changes using an optional handheld remote control or

repeater autopilot control unit (if fitted).

D1403-2A

81057_6.book Page 8 Tuesday, February 21, 2006 2:21 PM

Chapter 2: Operating the SportPilot 9

Adjusting autopilot gain

The autopilot gain setting determines the amount of rudder the pilot applies

during course change. Autopilot gain is relative to the speed of your boat.There

are five available gain settings on the SportPilot:

•

LO: lowest gain setting

• three mid-range positions

•

HI: highest gain setting

Setting the gain for your boat

WARNING:

It is vital that the autopilot gain control is set correctly – an

incorrect setting will lead to poor steering performance and can

produce violent course changes at high speed.

The ideal gain setting for one boat may not be ideal for another, so finding the

correct setting for your boat will be down to experimentation and experience. The

following

HI and LO setting details are general guidelines only.

HI gains

Generally, low boat speeds require a medium to

HI setting to provide better

course keeping.

WARNING:

This setting is not recommended for high speeds as it may cause

some instability and, therefore, could be dangerous.

LO gains

Most high speed boats will require a medium to

LO setting. This provides the

greatest stability.

D1402-2

LO gain

HI gain

Mid-range gain

81057_6.book Page 9 Tuesday, February 21, 2006 2:21 PM

10 ST60 Tridata Instrument Owner’s Manual

Automatic gain correction

Autopilot gain is automatically adjusted if the SportPilot is connected to either a:

• SeaTalk instrument transmitting boat speed through the water or boat speed

over the ground, or

• NMEA instrument transmitting NMEA 0183 boat speed through the water or

boat speed over the ground

Initially set the control stalk to the gain position most suited to your boat. The

SportPilot will then automatically adjust the gain (up or down) from this setting as

your boat speed changes.

Note:

The SportPilot must receive boat speed information via SeaTalk or NMEA to auto-

matically adjust the gain.

2.3 Using Navigator (Track) mode

The SportPilot can automatically steer to a waypoint using information from any

SeaTalk navigator or NMEA 0183 compatible GPS. Alternatively, the SportPilot

can follow a route defined on a SeaTalk Navcenter or GPS.

Entering Navigator (Track) mode

To enter Navigator mode so you follow a route of waypoints:

1. Create or select a route of waypoints on the navigator.

2. Engage the pilot and steer your boat onto the first waypoint bearing (within

0.3 nm of track).

3. Press in the end of the control stalk to enter Navigator (Track) mode. The yel-

low

NAV light glows to confirm this selection.

D1410-2

001

002

003

004

81057_6.book Page 10 Tuesday, February 21, 2006 2:21 PM

Chapter 2: Operating the SportPilot 11

Exiting Navigator (Track) mode

To exit Navigator (Track) mode and return to Standby mode, turn the end of the

control stick back to

STANDBY. The yellow NAV light will go out and the red

AUTO light will flash.

Turning to next waypoint

In Navigator (Track) mode, the SportPilot automatically determines the direction

to the target waypoint:

• if a turn to port is required, the SportPilot emits 2 short beeps

• if a starboard turn is needed, the SportPilot emits 1 short beep

To accept the turn, press in the end of the control stalk (

NAV).

CAUTION:

Before you accept a turn to port or starboard, ALWAYS make sure

that it is safe to do so.

Arriving at a waypoint

When you arrive at a target waypoint, the SportPilot requests permission to

advance to the next waypoint:

• two short beeps for a port turn

• one short beep for a starboard turn

Make sure that it is safe to make the turn, then press

NAV to advance to the next

waypoint.

D1358-2

81057_6.book Page 11 Tuesday, February 21, 2006 2:21 PM

12 ST60 Tridata Instrument Owner’s Manual

Safety points

The SportPilot can only follow a user defined route if the navigation equipment

transmits all of the following information:

• bearing to waypoint (BTW)

• cross track error (XTE)

•waypoint number

If cross track error (XTE) is the only available information, the SportPilot will

advance to the next waypoint without requesting permission. In this case, you

should always manually steer the boat to within 15° of the new bearing to

waypoint before you press

NAV.

Audible alarms in Navigator mode

The SportPilot emits the following audible warning alarms in Navigator (Track)

mode:

Audible alarm Reason

2 short beeps Turn to port required

1 short beep Turn to starboard required

2 short and 1 long beep Off course

Continuous short beeps Track problem (large XTE, no data or data error)

81057_6.book Page 12 Tuesday, February 21, 2006 2:21 PM

Chapter 3: Maintenance & Fault Finding 13

Chapter 3: Maintenance & Fault Finding

This chapter provides information about maintaining your SportPilot system,

obtaining product support and solving common problems.

3.1 General maintenance

CAUTION:

The SportPilot and fluxgate compass do not contain any user

serviceable parts. These products should be serviced only by

authorized Raymarine service technicians.

Routine cabling checks

• Make sure all connections are firmly attached.

• Examine the cables for signs of wear or damage – replace any damaged

cables.

Cleaning the SportPilot

• If the SportPilot is dirty, wipe it with a clean, damp cloth.

• Never use chemical or abrasive materials to clean the SportPilot.

EMC advice

• When powered up, all electrical equipment produces electromagnetic fields.

These can cause adjacent pieces of electrical equipment to interact with one

another, with a consequent adverse effect on operation.

• To minimize these effects and enable you to get the best possible perfor-

mance from your Raymarine equipment, guidelines are given in the installa-

tion instructions, to enable you to ensure minimum interaction between

different items of equipment, i.e. ensure optimum Electromagnetic Compati-

bility (EMC).

• Always report any EMC-related problems to your nearest Raymarine dealer.

We use such information to improve our quality standards.

• In some installations, it may not be possible to prevent the equipment from

being affected by external influences. In general this will not damage the

equipment but it can lead to spurious resetting action, or momentarily may

result in faulty operation.

81057_6.book Page 13 Tuesday, February 21, 2006 2:21 PM

14 ST60 Tridata Instrument Owner’s Manual

3.2 Fault finding

All Raymarine products are designed to provide many years of trouble-free

operation. We also put them through comprehensive testing and quality

assurance procedures before shipping.

In the unlikely event that a fault does occur with your autopilot, use the following

table to help identify the problem and provide a solution. If you cannot resolve the

problem yourself, refer to the product support information below.

3.3 Product support

Raymarine products are supported by a worldwide network of distributors and

Authorized Service Representatives. If you encounter any difficulties with this

product, please contact either your national distributor, service representative, or

the Raymarine Technical Services Call Center. Refer to the back cover or

the Worldwide Distributor List for contact details.

SYMPTOM CAUSE SOLUTION

SportPilot does not power

up.

Power connection at the

power supply or SportPi-

lot.

Blown fuse or circuit

breaker.

Make sure that all con-

nections are secure.

Replace fuse or circuit

breaker.

Over-active heading cor-

rection.

Autopilot gain too high. Turn control stalk

towards

LO gain.

Poor course keeping. Autopilot gain too low. Turn control stalk

towards HI gain.

Over-active heading cor-

rection or poor course

keeping after adjusting

the gain.

Pre-programmed set-

tings not suitable for

your boat.

If a rudder position sen-

sor is connected: the

SportPilot may not have

sensed its presence.

Contact your nearest

Raymarine dealer.

Auto-sensing can take

up to 10 minutes. During

this time you may expe-

rience poor course-keep-

ing.

NAV (Track) mode: Sport-

Pilot steers onto wrong

bearing after you accept

the turn alarm.

Compass heading align-

ment incorrect.

Complete the heading

alignment procedure

(see

page 51

)

81057_6.book Page 14 Tuesday, February 21, 2006 2:21 PM

Chapter 4: Installing the SportPilot 15

Chapter 4: Installing the SportPilot

Introduction

The SportPilot fits neatly over your boat’s existing steering shaft with the steering

wheel bolted directly onto the pilot. The unit can accommodate either

in (19

mm) or 1 in (25 mm) steering shaft tapers using a simple adaptor collar (supplied).

All installations require an external fluxgate compass (supplied) to feed the

SportPilot with precise heading information. This unit plugs directly into the rear

of the pilot. It should be mounted in a central location to minimize the effects of

pitching and rolling.

If your boat has a hydraulic helm pump, you must also fit a rudder position

sensor. You will need to use either a linear or rotary rudder sensor, depending on

your boat’s steering system (see

page 22

The sections in this chapter explain how to install and connect the components of

your SportPilot system:

4.1

Planning the installation

page 16

4.2

Installing the compass

page 19

4.3

Installing the rudder position sensor –

optional

page 22

4.4

Providing power for the SportPilot

page 34

4.5

Connecting SeaTalk equipment

page 36

4.6

Installing the SportPilot

page 38

81057_6.book Page 15 Tuesday, February 21, 2006 2:21 PM

16 ST60 Tridata Instrument Owner’s Manual

4.1 Planning the installation

SportPilot and

SportPilot Plus

Owner's

Handbook

Worldwide

Distributors

D1406-2

Owner's Handbook Worldwide Distributor List Quick Reference Card

SportPilot/SportPilot Plus

Front Back

Bracket

3mm allen key

3.4mm drill bit

Box spanner

(15/16 in and 3/4 in)

Fluxgate

compass

Power cable

Retaining nuts (3/8in, 1/2in, 5/8in)

and washers (M12 x 1, M16 x 2)

Adaptor collar

Raymarine woodruff key

Steering boss

M4 x 12mm screw

and washer (x4)

Steering boss parts

No8 x 3/4in self-tapping

pan-head screws (x4)

No8 x 3/4 in

countersunk screw (x4)

M4 x 40 mm bolt

and washer

Cable sealing mat

Torque restraint parts

Cable holder parts

Bracket

template

M3 x 8 mm

screw (x2)

Compass

warning label

Cable holder

Optional:

Rotary or

linear rudder

position

sensor and

fittings

81057_6.book Page 16 Tuesday, February 21, 2006 2:21 PM

Page is loading ...

Raymarine SportPilot Owner's Handbook Manual

Brand: Raymarine

Model: SportPilot

Category: Navigators

Type: Owner's Handbook Manual

This manual is also suitable for

SportPilot Plus

Download PDF

report

Raymarine SportPilot Owner's Handbook Manual

This manual is also suitable for

Raymarine SportPilot Owner's Handbook Manual

Related papers

Other documents