Simplicity 117462-0501-E1 Operating instructions

Document: - page 1 (Black)

Screen angle and frequency: 45.0000, 150.0000

Briggs & Stratton Corporation

Milwaukee, Wisconsin 53201

www.briggsandstratton.com

FORM NO. MS-6669-5/03

PRINTED IN U.S.A.

   

   

  

    

    

   

     

!  "  "

#"$

%&  %'   %'

""

()*+  ,

-..../ 0-1../ 021../ 33-1../ 3341../ 3301../

3501../ 3011../ 30-1../ 65-1../ 61-1..

GB

D

E

DK

F

I

NL

P

SF

S

N

GR

Page is loading ...

GB

1

Note: (This note applies only to engines used in the U.S.A.) Maintenance, replacement or repair of the emission control devices and systems may be performed

by any nonroad engine repair establishment or individual. However, to obtain no charge repairs under the terms and provisions of the Briggs & Stratton

warranty statement, any service or emission control part repair or replacement must be performed by a factory authorized dealer.

- refer to engine components in figure .

19

How To Use Manual Figures

 - refer to figures inside covers.

 -  refer to part/action in figures.

1

Record your engine Model, Type and Code numbers

here for future use.

Record your date of purchase here for future use.

In the state of California, Model Series 50000, 85400,

86400, 115400, 117400, 118400, 138400 engines are

certified by the California Air Resources Board to meet

emissions standards for 125 hours; Model Series

184400, 185400, 235400, 245400 for 250 hours. Such

certification does not grant the purchaser, owner or

operator of this engine any additional warranties with

respect to the performance or operational life of this

engine. This engine is warranted solely according to

the product and emissions warranties stated elseĆ

where in this manual.

Technical Information

Power Ratings

The power ratings for an individual engine model are initially

developed by starting with SAE (Society of Automotive

Engineers) code J1940 (Small Engine Power & Torque Rating

Procedure) (Revision 2002Ć05). Given both the wide array of

products on which our engines are placed, and the variety of

environmental issues applicable to operating the equipment, it

may be that the engine you have purchased will not develop

the rated horsepower when used in a piece of power

equipment (actual onĆsite" power). This difference is due to a

variety of factors including, but not limited to, the following:

differences in altitude, temperature, barometric pressure,

humidity, fuel, engine lubrication, maximum governed engine

speed, individual engine to engine variability, design of the

particular piece of power equipment, the manner in which the

engine is operated, engine runĆin to reduce friction and clean

out of combustion chambers, adjustments to the valves and

carburetor, and other factors. The power ratings may also be

adjusted based on comparisons to other similar engines

utilized in similar applications, and will therefore not necessariĆ

ly match the values derived using the foregoing codes.

Engine Components (see fig. )

1

Fuel shutĆoff valve

2

Rope handle

3

Air cleaner

4

Engine Model Type Code

xxxxxx xxxx xx xxxxxxxx

5

Throttle and choke controls

6

Fuel fill

7

Stop switch/Oil Gard, if equipped

8

Blower housing

9

Oil drain plug

10

Muffler guard/Muffler

11

Carburetor

12

Spark plug wire

13

Oil fill/Dipstick

14

12V electric starter, if equipped

Hazard Symbols and Meanings

Explosion

Toxic Fumes

Moving Parts

Shock

Hot Surface

Kickback

Fire

International Symbols and Meanings

On Off

Fuel Shutoff

Read Owner's

Manual

Stop

Fuel

ChokeSafety Alert

Oil

Safety Precautions

* Briggs & Stratton does not necessarily know what

equipment this engine will power. For that reason, you

should carefully read and understand the operating

instructions for the equipment on which your engine is

placed.

BEFORE OPERATING ENGINE

• Read entire Operating & Maintenance Instructions

AND the instructions for the equipment this engine

powers.*

• Failure to follow instructions could result in serious

injury or death.

THE OPERATING & MAINTENANCE INSTRUCTIONS

CONTAIN SAFETY INFORMATION TO

• Make you aware of hazards associated with engines

• Inform you of the risk of injury associated with those

hazards, and

• Tell you how to avoid or reduce the risk of injury.

The safety alert symbol is used to identify safety

information about hazards that can result in personal injury.

A signal word (DANGER, WARNING, or CAUTION) is used

with the alert symbol to indicate the likelihood and the potential

severity of injury. In addition, a hazard symbol may be used to

represent the type of hazard.

DANGER indicates a hazard which, if not avoided,

will result in death or serious injury.

WARNING indicates a hazard which, if not avoided,

could result in death or serious injury.

CAUTION indicates a hazard which, if not avoided,

might result in minor or moderate injury.

CAUTION, when used without the alert symbol,

indicates a situation that could result in damage to

the engine.

The engine exhaust from this product contains

chemicals known to the State of California to cause

cancer, birth defects, or other reproductive harm.

WARNING

GB

2

WARNING

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or death.

WHEN ADDING GASOLINE

• Turn engine OFF and let engine cool at least 2

minutes before refueling engine.

• Fill fuel tank outdoors or in wellĆventilated area.

• Do not overfill fuel tank. Fill tank to approximately

1Ć1/2 inches below top of neck to allow for fuel

expansion.

• Keep gasoline away from sparks, open flames, pilot

lights, heat, and other ignition sources.

• Check fuel lines, tank, cap, and fittings frequently

for cracks or leaks. Replace if necessary.

WHEN STARTING ENGINE

• Make sure spark plug, muffler, fuel cap and air

cleaner are in place.

• Do not crank engine with spark plug removed.

• If fuel spills, wait until it evaporates before starting

engine.

• If engine floods, set choke to OPEN/RUN position,

place throttle in FAST and crank until engine starts.

WHEN OPERATING EQUIPMENT WITH

GASOLINE ENGINE

• Do not tip engine or equipment at angle which

causes gasoline to spill.

• Do not choke carburetor to stop engine.

WHEN TRANSPORTING EQUIPMENT

• Transport with fuel tank EMPTY or with fuel shutĆoff

valve OFF, and/or fuel cylinder empty.

WHEN STORING FUEL OR EQUIPMENT

• Store away from furnaces, stoves, water heaters or

other appliances that have pilot light or other ignition

source because they can ignite gaseous vapors.

WARNING

• When starting engine, pull cord slowly until

resistance is felt, then pull rapidly.

• Remove all external equipment/engine loads

before starting engine.

• Direct coupled equipment components such as, but

not limited to, blades, impellors, pulleys, sprockets,

etc., must be securely attached.

Rapid retraction of starter cord (kickback) will pull hand and

arm toward engine faster than you can let go.

Broken bones, fractures, bruises or sprains could result.

• Operate equipment with guards in place.

• Keep hands and feet away from rotating parts.

• Tie up long hair and remove jewelry.

• Do not wear looseĆfitting clothing, dangling

drawstrings or items that could become caught.

Unintentional sparking can result in fire or electric shock.

Unintentional startĆup can result in entanglement, trauĆ

matic amputation, or laceration.

BEFORE PERFORMING ADJUSTMENTS OR REĆ

PAIRS

• Disconnect spark plug wire and keep it away from

spark plug.

• Disconnect battery at negative terminal (only

engines with electric start).

WHEN TESTING FOR SPARK

• Use approved spark plug tester.

• Do not check for spark with spark plug removed.

WARNING

Engines give off carbon monoxide, an odorless, colorless,

poison gas.

Breathing carbon monoxide can cause nausea, fainting or

death.

• Start and run engine outdoors.

• Do not start or run engine in enclosed area, even if

doors or windows are open.

WARNING

• If there is natural or LP gas leakage in area, do not

start engine.

• Do not use pressurized starting fluids because

vapors are flammable.

• Servicing of products fueled by Natural Gas (NG) or

Liquid Petroleum Gas (LPG) may require licensing

or permits issued by state, provincial, and/or local

governments.

WARNING

Starting engine creates sparking.

Sparking can ignite nearby flammable gases.

Explosion and fire could result.

WARNING

Rotating parts can contact or entangle hands, feet, hair,

clothing, or accessories.

Traumatic amputation or severe laceration can result.

Running engines produce heat. Engine parts, especially

muffler, become extremely hot.

Severe thermal burns can occur on contact.

Combustible debris, such as leaves, grass, brush, etc. can

catch fire.

• Allow muffler, engine cylinder and fins to cool before

touching.

• Remove accumulated combustibles from muffler

area and cylinder area.

• Install and maintain in working order a spark

arrester before using equipment on forestĆcovered,

grassĆcovered, brushĆcovered unimproved land.

The state of California requires this (Section 4442 of

the California Public Resources Code). Other

states may have similar laws. Federal laws apply on

federal land.

WARNING

IF YOU SMELL LPG / NG GAS:

• DO NOT start the engine.

• DO NOT actuate any electrical switches.

• DO NOT use the phone in the vicinity.

• Evacuate the area, LPG / NG gas is a toxic fume.

• Contact the gas supplier or fire department.

REMEMBER:

• LPG vapor is heavier than air and trends to collect in

low areas. NG vapor is lighter than air and tends to

collect in high areas. Both may travel to remote

locations.

• Keep all flames, sparks, pilot lights, and other

ignition sources away from the area where the

engine is operated or repaired.

• DO NOT smoke when operating or repairing the

engine.

• DO NOT store gasoline or other flammable vapors

or liquids in the vicinity of the engine.

• BEFORE doing any service work to the engine,

shut off the gas supply.

• After initial installation or servicing, check for gas

leaks. DO NOT use an open flame. Apply very

soapy water or leak test solution with a brush and

look for bubbles.

• Keep the area surrounding the engine and

equipment it powers free of debris.

• Install the fuel system according to applicable

fuel/gas codes.

• Check fuel supply lines regularly for cracks or wear.

Replace if damaged.

Gaseous fuels are extremely flammable and readily form

explosive airĆvapor mixtures at ambient temperatures.

GB

3

Oil Recommendations (see fig. )

Engine shipped from Briggs & Stratton without

oil.

Before starting engine

, fill with oil. Do not overĆfill.

Use a high quality detergent oil classified For Service

SF, SG, SH, SJ" or higher such as Briggs & Stratton

30W, Part Number 100005 (20 oz.) or 100028 (48 oz.).

Use no special additives with recommended oils. Do

not mix oil with gasoline.

Choose the SAE viscosity grade of oil from this chart

that matches the starting temperature anticipated

before the next oil change.

Note: Synthetic oil meeting ILSAC

GFĆ2, API certification mark and API serĆ

vice symbol (shown at left) with SJ/CF

ENERGY CONSERVING" or higher, is an

acceptable oil at all temperatures. Use of

synthetic oil does not alter required oil

change intervals.

* Air cooled engines run hotter than automotive

engines. The use of nonĆsynthetic multiĆviscosity

oils (5WĆ30, 10WĆ30, etc.) in temperatures

above 40° F (4° C) will result in higher than

normal oil consumption. When using a multiĆvisĆ

cosity oil, check oil level more frequently.

** SAE 30 oil, if used below 40° F (4° C), will result

in hard starting and possible engine bore

damage due to inadequate lubrication.

Check oil level (approximate capacities)

Model Series

Liters Ounces

050000 0.4 13.5

085400 & 086400 0.6 20

1154, 1174, 1184 0.7 24

138400 0.9 30

184400 & 185400 1.2 41

235400 & 245400 1.5 51

Place engine level and clean around oil fill .

Remove dipstick and wipe with clean cloth. Insert

dipstick in oil fill - tighten down if high oil fill

, but do

not tighten down if low oil fill

 - remove dipstick to

check oil level. Oil should be at FULL mark

.

If oil is required, add slowly. Do not overĆfill. Tighten

dipstick firmly before starting engine.

Fuel Recommendations

THE GASOLINE ENGINE IS CERTIFIED TO OPERĆ

ATE ON GASOLINE. Exhaust Emission Control SysĆ

tem: EM (Engine Modifications).

Use clean, fresh, leadĆfree

gasoline with a minimum of

85 octane. Leaded gasoline may be used if it is

commercially available and if unleaded is unavailable.

Purchase fuel in quantity that can be used within 30

days. See Storage.

In U.S.A. leaded gasoline may not be used. Some

fuels, called oxygenated or reformulated gasolines, are

gasolines blended with alcohols or ethers. Excessive

amounts of these blends can damage the fuel system

or cause performance problems. If any undesirable

operating symptoms occur, use gasoline with a lower

percentage of alcohol or ether.

Do not use gasoline which contains Methanol. Do not

mix oil with gasoline.

THE MODEL 1844 ENGINE IS CERTIFIED TO OPERĆ

ATE ON LPG / NG FUEL.

Use clean, dry fuel, free of moisture or any particulate

material. Using fuels outside the following recomĆ

mended values may cause performance problems.

In engines set up to run on LPG, commercial grade

HD5 LPG is recommended. Recommended fuel comĆ

position is fuel with a minimum fuel energy of 2500

BTU's/ft

3

with maximim propylene content of 5% and

butane and heavier gas content of 2.5% and minimum

propane content of 90%.

Check fuel level - Gasoline Engines.

Before refueling, allow

engine to cool 2 minutes.

Clean around fuel fill before removing cap to refuel. Fill

tank to approximately 1Ć1/2 inches below top of neck to

allow for fuel expansion. Be careful not to overfill.

Starting (see figs. )

ALWAYS KEEP HANDS AND FEET

CLEAR OF EQUIPMENT MOVING

PARTS.

Do not use a pressurized starting fluid.

Vapors are flammable.

Start, store and fuel equipment in level position.

Check oil level.

Open fuel shutĆoff valve, if equipped.

OIL GARD

If engine is equipped with OIL GARD, and if engine

runs low on oil and cannot be started or has stopped and

cannot be restarted, add oil. Fill to FULL mark on

dipstick. Do not overĆfill.

CAUTION: OIL GARD will shut down a running

engine. Engine damage may occur if oil level is not

properly maintained and will void warranty coverĆ

age.

Starting Cont'd

BEFORE STARTING - LPG / NG Engines.

(see fig. )

The LPG / NG mixer is equipped with solenoid

, fuel

inlet

, 12 volt connector , and equipped for a fuel

lockĆoff valve

.

CAUTION:

All LPG / NG fuel mixers are equipped with a

solenoid

.

When operating on LPG fuel, 12 volts MUST be

supplied to connector

.

When operating on NG fuel, 12 volts MUST NOT be

supplied to connector .

STARTING (see fig. )

1. On gasoline engine, move choke control

 to

CHOKE position. On LPG/NG engine, open fuel

shutĆoff valve.

2. Move throttle control

 to FAST position.

3. Turn fuel shutĆoff valve

 on, if equipped on

gasoline engine.

4. Move stop control

 to ON position, if equipped.

Rewind starter, if equipped (see fig.)

Grasp rope handle and pull slowly until

resistance is felt. Then pull cord rapidly

to overcome compression, prevent

kickback and start engine. Repeat if

necessary with choke in RUN position and throttle i

n

FAST. When engine starts, operate in FAST position.

Electric starter, if equipped

(see fig.)

On engines equipped with 12 volt starting systems, turn

key  to START position. Repeat if necessary with

throttle control in FAST position. When engine starts,

operate in FAST position.

Note: If equipment manufacturer has supplied battery,

charge it before trying to start engine, as equipment

manufacturer recommends.

Note: Use short starting cycles (15 secs. per min.) to

prolong starter life. Extended cranking can damage

starter motor.

Stopping (see fig.)

Do not move choke control to CHOKE position to stop

engine. Backfire or engine damage may occur. Move

throttle control  to IDLE or SLOW position, if

equipped. Then turn key

 to OFF or move stop

control

 to OFF position. Close fuel shutĆoff valve .

Note: Always remove key from switch when equipment

is not in use or left unattended.

Note: When engine is transported, close fuel shutĆoff

valve to prevent leakage.

GB

4

Maintenance (see figs. )

See Maintenance Schedule. Follow the hourly or

calendar intervals, whichever occur first. More frequent

service is required when operating in adverse conditions.

To prevent acciĆ

dental starting, reĆ

move spark plug

wire  and ground

it before servicing,

and disconnect battery at negative terminal, if equipped.

Oil service

(see fig. )

Check oil level regularly.

Be sure correct oil level is maintained. Check every 8

hours or daily, before starting engine. See oil filling

procedure under Oil Recommendations.

Change oil.

Change oil after first 5 hours of operation. Change oil

while engine is warm. Refill with new oil of recomĆ

mended SAE viscosity grade.

Air cleaner service

(see fig. )

Replace preĆcleaner

, and/or cartridge  if very dirty

or damaged.

1. Loosen screws. Remove cover and air cleaner

assembly from base.

2. Remove cartridge (retainer

, if equipped) and

preĆcleaner.

To service preĆcleaner, wash in liquid detergent and

water. Squeeze dry in a clean cloth. Saturate in engine

oil. Squeeze in clean, absorbent cloth to remove ALL

EXCESS oil.

To service cartridge, clean by tapping gently on a flat

surface. Do not use petroleum solvents, e.g., keroĆ

sene, which will cause cartridge to deteriorate. Do not

use pressurized air, which can damage cartridge. Do

not oil cartridge.

3. Reinstall preĆcleaner on retainer, if equipped.

4. Install preĆcleaner in cover with mesh side toward

cartridge. Install cartridge in cover or on base.

5. Seat cover and air cleaner assembly squarely

onto base (tabs

 into slots , if equipped).

6. Tighten cover screws securely.

Check valve clearance:

intake is .05 mm and exhaust .10 mm.

Spark plug service

(see fig. )

DO NOT check for spark with

spark plug removed. Use

only Briggs & Stratton Spark

Te s te r , to check for spark.

DO NOT crank engine with spark plug removed. If

engine is flooded, place throttle in FAST and crank until

engine starts.

Spark plug gap  should be .76 mm or 0.030 in.

Replace spark plug every 100 hours or every season,

whichever occurs first. Spark tester and spark plug

wrench are available from any Authorized Briggs &

Stratton Service Dealer.

Note: In some areas, local law requires using a resistor

spark plug to suppress ignition signals. If this engine

was originally equipped with resistor spark plug, use

same type of spark plug for replacement.

Maintenance Cont'd

Keep engine clean (see fig. )

Periodically remove chaff and debris buildĆup from

engine. Do not spray engine with water to clean

because water could contaminate fuel. Clean with a

brush or compressed air.

To assure smooth operation, keep governor linkage,

springs and controls free of debris

.

Accumulation of debris around mufĆ

fler  could cause a fire. Inspect and

clean before every use.

If muffler is equipped with spark arrester screen

,

remove spark arrester screen for cleaning and inspecĆ

tion every 50 hours or every season. Replace if

damaged.

Clean cooling system. Chaff or debris may clog engine's

air cooling system, especially after prolonged operation.

Internal cooling fins and surfaces may require cleaning

to prevent overheating and engine damage. Remove

blower housing and clean as shown

.

Clean fuel filter

(see fig. )

Gasoline Engines: Clean fuel filter

screen . Drain fuel tank or close

fuel shutĆoff valve before cleaning filter.

LPG / NG Engines: If equipped, follow equipment

manufacturers recommended maintenance inĆ

structions.

Adjustments

To prevent acciĆ

dental starting, reĆ

move spark plug

wire  and ground

it before adjusting, and disconnect battery at negative

terminal, if equipped.

Throttle control adjustments

(see fig. )

Manual friction throttle control

If adjustment is required, loosen or tighten lock nut



until throttle control  moves easily, but stays in set

position.

Fixed governor control

Adjustable governor control has been set to permit top

noĆload rpm specified by equipment manufacturer. If

adjustment is required, consult any Briggs & Stratton

Authorized Service Dealer.

Adjustments Cont'd

Carburetor adjustment - Gasoline Engines

The manufacturer of the equipment on which

this engine is installed specifies top speed at

which the engine will be operated. DO NOT

EXCEED this speed.

See an Authorized Briggs & Stratton Dealer for

carburetor adjustment.

Start engine and warm up approximately 5 minutes

before adjusting. With engine running, place throttle

control in SLOW position. Rotate carburetor throttle lever

against the idle speed screw and hold it. Turn idle speed

screw to obtain 1300 rpm. While still holding carburetor

throttle lever against idle speed screw, turn idle mixture

valve with limiter cap midway between limits. Release

carburetor throttle lever.

Adjust governed idle speed screw to 1400 rpm, set to

1750 rpm on Model Series 235400 and 245400. Move

throttle control to FAST position. Engine should accelerĆ

ate smoothly. If it does not, adjust carburetor idle mixture

valve counterclockwise 1/8 turn.

(If Top Speed requires adjustment, see equipment

manufacturer's specifications.)

IDLE SPEED

SCREW

IDLE MIXTURE

VALVE WITH

LIMITER CAP

GOVERNED

IDLE SPEED

SCREW

CARBURETOR

THROTTLE

LEVER

TOP SPEED

SCREW

IDLE SPEED

SCREW

IDLE MIXTURE VALVE

WITH LIMITER CAP

CARBURETOR

THROTTLE

LEVER

MODEL SERIES 050000, 086400 & 118400

Mixer adjustment - LPG / NG Engines

The LPG / NG fuel mixer has a preĆset adjustment. If

adjustment is needed, see a Briggs & Stratton AuthoĆ

rized Service Dealer who has been licensed by the

state or local municipality (if required) in which the

service is performed. Mixer adjustment requires speĆ

cial equipment and a qualified technician.

GB

5

Maintenance Schedule

Follow the hourly or calendar intervals, whichever

occur first. More frequent service is required when

operating in adverse conditions noted below.

First 5 Hours

D Change oil

Every 8 hours or daily

D Check oil level

D Clean around muffler, springs and linkages

Every 25 hours or every season

D Change oil if operating under heavy load or

high ambient temperature

D Service air cleaner preĆcleaner*

Every 50 hours or every season

D Change oil

D Clean and inspect spark arrester, if equipped

D Clean fuel filter**

Every 100 hours or every season

D Service air cleaner cartridge*

D Replace spark plug

D Clean cooling system*

Every season

D Check valve clearance

* Clean more often under dusty conditions,or

when airborne debris or chaff is present.

** If equipped with gaseous fuel inĆline filter,

follow equipment manufacturers recomĆ

mended maintenance.

Partial List of Genuine Briggs & Stratton Parts

CAUTION: Part numbers listed may be model specifĆ

ic, use correct part to prevent damage to your engine.

Model Series Part

Part

No.

ALL

Oil

(20 oz., 0.59 l)

100005

ALL

Oil

(48 oz., 1.42 l)

100028

ALL

Oil Pump

(uses standard

electric drill)

5056

ALL Fuel Stabilizer 5058

050000

Air Cleaner

Cartridge

711351

050000

Air Cleaner

PreĆcleaner

711352

085400

Air Cleaner

Cartridge

710265

085400

Air Cleaner

PreĆcleaner

710267

115400

Air Cleaner

Cartridge

494511

115400

Air Cleaner

PreĆcleaner

492889

086400

117400

115400

138400

184400

185400 - if equipped

Square

Air Cleaner

Cartridge

491588

086400

117400

115400

138400

184400

185400 - if equipped

Square

Air Cleaner

PreĆcleaner

491435

185400

235400

245400

Air Cleaner

Cartridge

710266

185400

235400

245400

Air Cleaner

PreĆcleaner

710268

ALL

(Except 050000,

086400, 118400)

Resistor Spark

Plug

491055

050000

086400

118400

Resistor Spark

Plug

711252

ALL OHV engines

(Except 118400)

Long Life

Platinum Spark

Plug

491055

ALL Spark Tester 19368

ALL

Spark Plug

Wrench

19374

Storage

Gasoline engines stored over 30 days need to be

protected or drained of fuel to prevent gum from

forming in fuel system or on essential carburetor parts.

For gasoline engine protection, we recommend use of

Briggs & Stratton Fuel Stabilizer available from an

Authorized Briggs & Stratton Service Dealer. Mix

stabilizer with fuel in fuel tank or storage container. Run

engine for a short time to circulate stabilizer through

carburetor. Engine and fuel can be stored up to 24

months.

Note: If stabilizer is not used or if engine is operating on

gasoline containing alcohol, e.g. gasohol, remove all fuel

from tank and run engine until it stops from lack of fuel.

Storage Procedures for Gas/LPG/NG engines.

1. Change oil. See Oil service. (see figs.

)

2. Remove spark plug and pour about 15 ml (1/2

oz.) of engine oil into cylinder. Replace spark plug

and crank slowly to distribute oil.

3. Clean chaff and debris from cylinder and cylinder

head fins, under finger guard and behind muffler.

4. Store in a clean and dry area, but NOT near a

stove, furnace or water heater which uses a pilot

light or any device that can create a spark.

Service

See an Authorized Briggs & Stratton Service Dealer.

Each one carries a stock of Genuine Briggs & Stratton

Parts and is equipped with special service tools.

Trained mechanics assure expert repair service on all

Briggs & Stratton engines. Only dealers advertising as

Authorized Briggs & Stratton" are required to meet

Briggs & Stratton standards.

When you purchase equipment powĆ

ered by a Briggs & Stratton engine, you

are assured of highly skilled, reliable

service at more than 30,000 Authorized

Service Dealers worldwide, including

more than 5,000 Master Service TechniĆ

cians. Look for these signs wherever

Briggs & Stratton service is offered.

You may locate your nearest Authorized Briggs &

Stratton Service Dealer in our dealer locator map on

our web site www.briggsandstratton.com or in the

Yellow Pages" directory under Engines,

Gasoline" or Gasoline Engines," or Lawn

Mowers" or similar category.



Note: Walking fingers logo and Yellow Pages" are

registered trademarks in various jurisdictions.

An illustrated shop manual includes Theories of

Operation," common specifications and detailed

information covering adjustment, tuneĆup and repair of

Briggs & Stratton single cylinder, OHV 4 cycle engines.

Order P/N 272147 from an Authorized Briggs &

Stratton Service Dealer.

Insist on Genuine Briggs & Stratton replacement āparts

with our logo on the box and/or part. NonĆoriginal parts

may not perform as well and may void your warranty.

GB

6

BRIGGS & STRATTON ENGINE OWNER WARRANTY POLICY

Effective January 1, 2003 replaces all undated Warranties and all Warranties dated before January 1, 2003

LIMITED WARRANTY

Briggs & Stratton Corporation will repair or replace, free of charge, any part(s) of the engine that is defective in material or workmanship or both. Trans-

portation charges on parts submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is effective for the time

periods and subject to the conditions stated below. For warranty service, find the nearest Authorized Service Dealer in our dealer locator map at

www.briggsandstratton.com, or by calling 1-800-233-3723, or as listed in the ‘Yellow Pages’.

THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICU-

LAR PURPOSE, ARE LIMITED TO ONE YEAR FROM PURCHASE, OR TO THE EXTENT PERMITTED BY LAW ANY AND ALL IMPLIED WARRANTIES

ARE EXCLUDED. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE EXCLUDED TO THE EXTENT EXCLUSION IS PERMITTED BY

LAW. Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not allow the exclusion or

limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you specific legal rights

and you may also have other rights which vary from state to state and country to country.

VANGUARD

ELS

I/Cr

Industrial Plus

Intek

(Sleeve Bore)

Fource

Intek

(Kool Bore)

Power Built OHV

QUANTUMr

Quattro

Q45

Sprint

Classic

Commercial Use

2 years

90 days

1 year

Consumer Use

2 years 2 years

90 days

1 year

OUR PRODUCT

WARRANTY PERIOD*

Etek

1 year

* Note the following special warranty periods: 2 years for Classic engines in the European Union and Eastern European countries, for all consumer products in the European Union, and for

emission control systems on engines certified by EPA and CARB. 5 years for consumer use, 90 days for commercial use of Touch-N-Mow starter on Quantum and Intek engines. Engines

used in competitive racing or on commercial or rental tracks are not warrantied.

The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the period of time stated in the table above. “Consumer use”

means personal residential household use by a retail consumer. “Commercial use” means all other uses, including use for commercial, income producing or rental purposes. Once an

engine has experienced commercial use, it shall thereafter be considered as a commercial use engine for purposes of this warranty.

NO WARRANTY REGISTRATION IS NECESSARY TO OBTAIN WARRANTY ON BRIGGS & STRATTON PRODUCTS. SAVE YOUR PROOF OF PURCHASE RECEIPT. IF

YOU DO NOT PROVIDE PROOF OF THE INITIAL PURCHASE DATE AT THE TIME WARRANTY SERVICE IS REQUESTED, THE MANUFACTURING DATE OF THE

PRODUCT WILL BE USED TO DETERMINE THE WARRANTY PERIOD.

ABOUT YOUR ENGINE WARRANTY

Briggs & Stratton welcomes warranty repair and apologizes to

you for being inconvenienced. Any Authorized Service Dealer

may perform warranty repairs. Most warranty repairs are hanĆ

dled routinely, but sometimes requests for warranty service may

not be appropriate. For example, warranty would not apply if enĆ

gine damage occurred because of misuse, lack of routine mainĆ

tenance, shipping, handling, warehousing or improper installaĆ

tion. Similarly, warranty is void if the serial number of the engine

has been removed or the engine has been altered or modified.

If a customer differs with the decision of the Service Dealer, an

investigation will be made to determine whether the warranty

applies. Ask the Service Dealer to submit all supporting facts to

his Distributor or the Factory for review. If the Distributor or the

Factory decides that the claim is justified, the customer will be

fully reimbursed for those items that are defective. To avoid misĆ

understanding which might occur between the customer and the

Dealer, listed below are some of the causes of engine failure that

the warranty does not cover.

Normal wear:

Engines, like all mechanical devices, need periodic parts serĆ

vice and replacement to perform well. Warranty will not cover reĆ

pair when normal use has exhausted the life of a part or an enĆ

gine.

Improper maintenance:

The life of an engine depends upon the conditions under which it

operates, and the care it receives. Some applications, such as

tillers, pumps and rotary mowers, are very often used in dusty or

dirty conditions, which can cause what appears to be premature

wear. Such wear, when caused by dirt, dust, spark plug cleaning

grit, or other abrasive material that has entered the engine beĆ

cause of improper maintenance, is not covered by warranty.

This warranty covers engine related defective material and/

or workmanship only, and not replacement or refund of the

equipment to which the engine may be mounted. Nor does

the warranty extend to repairs required because of:

1. PROBLEMS CAUSED BY PARTS THAT ARE NOT

ORIGINAL BRIGGS & STRATTON PARTS.

2. Equipment controls or installations that prevent starting,

cause unsatisfactory engine performance, or shorten enĆ

gine life. (Contact equipment manufacturer.)

3. Leaking carburetors, clogged fuel pipes, sticking valves,

or other damage, caused by using contaminated or stale

fuel. (Use clean, fresh, leadĆfree gasoline and Briggs &

Stratton Fuel Stabilizer, Part No. 5041.)

4. Parts which are scored or broken because an engine was

operated with insufficient or contaminated lubricating oil,

or an incorrect grade of lubricating oil (check oil level daily

or after every 8 hours of operation. Refill when necessary

and change at recommended intervals.) OIL GARD

may not shut down running engine. Engine damage may

occur if oil level is not properly maintained. Read OperatĆ

ing & Maintenance Instructions.

5. Repair or adjustment of associated parts or assemblies

such as clutches, transmissions, remote controls, etc.,

which are not manufactured by Briggs & Stratton.

6. Damage or wear to parts caused by dirt, which entered the

engine because of improper air cleaner maintenance,

reĆassembly, or use of a nonĆoriginal air cleaner element

or cartridge. (At recommended intervals, clean and reĆoil

the OilĆFoam element or the foam preĆcleaner, and

replace the cartridge.) Read Operating & Maintenance

Instructions.

7. Parts damaged by overĆspeeding, or overheating caused

by grass, debris, or dirt, which plugs or clogs the cooling

fins, or flywheel area, or damage caused by operating the

engine in a confined area without sufficient ventilation.

(Clean fins on the cylinder, cylinder head and flywheel at

recommended intervals.) Read Operating & Maintenance

Instructions.

8. Engine or equipment parts broken by excessive vibration

caused by a loose engine mounting, loose cutter blades,

unbalanced blades or loose or unbalanced impellers, imĆ

proper attachment of equipment to engine crankshaft,

overĆspeeding or other abuse in operation.

9. A bent or broken crankshaft, caused by striking a solid obĆ

ject with the cutter blade of a rotary lawn mower, or excesĆ

sive vĆbelt tightness.

10. Routine tuneĆup or adjustment of the engine.

11. Engine or engine component failure, i.e., combustion

chamber, valves, valve seats, valve guides, or burned

starter motor windings, caused by the use of alternate

fuels such as, liquified petroleum, natural gas, altered

gasolines, etc.

Warranty is available only through service dealers which

have been authorized by Briggs & Stratton Corporation.

your nearest Authorized Service Dealer is listed in the YelĆ

low Pages" of your telephone directory under Engines,

Gasoline" or Gasoline Engines," Lawn Mowers," or simiĆ

lar category.

Briggs & Stratton Engines Are Made Under One Or More Of The Following Patents: Design DĆ247,177 (Other Patents Pending)

6,325,036

6,284,123

6,260,529

6,230,678

6,202,616

6,116,212

6,077,063

6,064,027

6,014,808

5,894,715

5,852,951

5,823,153

5,819,513

5,813,384

5,765,713

5,645,025

5,642,701

5,619,845

5,606,948

5,606,851

5,548,955

5,546,901

5,503,125

5,501,203

5,497,679

5,320,795

5,271,363

5,269,713

5,265,700

5,243,878

5,235,943

5,197,425

5,197,422

5,191,864

5,188,069

5,186,142

5,138,996

5,086,890

5,070,829

5,058,544

5,040,644

5,009,208

4,996,956

4,977,879

4,971,219

4,895,119

4,819,593

4,719,682

4,633,556

4,630,498

4,522,080

4,520,288

4,512,499

4,453,507

4,430,984

DES. 308,871

DES. 308,872

DES. 309,457

DES. 356,951

DES. 361,771

DES. 375,963

Page is loading ...

(This page applicable in the U.S.A. and Canada only.)

Briggs & Stratton Corporation (B&S), the California Air Resources Board (CARB)

and the United States Environmental Protection Agency (U.S. EPA)

Emission Control System Warranty Statement (Owner's Defect Warranty Rights and Obligations)

EMISSION CONTROL WARRANTY COVERAGE IS APPLICABLE TO CERTIFIED ENGINES PURĆ

CHASED IN CALIFORNIA IN 1995 AND THEREAFTER, WHICH ARE USED IN CALIFORNIA, AND

TO CERTIFIED MODEL YEAR 1997 AND LATER ENGINES WHICH ARE PURCHASED AND USED

ELSEWHERE IN THE UNITED STATES (AND AFTER JANUARY 1, 2001 IN CANADA).

California, United States and Canada Emission Control Defects Warranty Statement

The California Air Resources Board (CARB), U.S. EPA and B&S are pleased to explain the Emission

Control System Warranty on your model year 2000 and later small offĆroad engine (SORE). In CaliforĆ

nia, new small offĆroad engines must be designed, built and equipped to meet the State's stringent antiĆ

smog standards. Elsewhere in the United States, new nonĆroad, sparkĆignition engines certified for

model year 1997 and later, must meet similar standards set forth by the U.S. EPA. B&S must warrant

the emission control system on your engine for the periods of time listed below, provided there has been

no abuse, neglect or improper maintenance of your small offĆroad engine.

Your emission control system includes parts such as the carburetor, air cleaner, ignition system,

muffler and catalytic converter. Also included may be connectors and other emission related asĆ

semblies.

Where a warrantable condition exists, B&S will repair your small offĆroad engine at no cost to you

including diagnosis, parts and labor.

Briggs & Stratton Emission Control Defects Warranty Coverage

Small offĆroad engines are warranted relative to emission control parts defects for a period of two

years, subject to provisions set forth below. If any covered part on your engine is defective, the part

will be repaired or replaced by B&S.

Owner's Warranty Responsibilities

As the small offĆroad engine owner, you are responsible for the performance of the required mainteĆ

nance listed in your Operating and Maintenance Instructions. B&S recommends that you retain all

your receipts covering maintenance on your small offĆroad engine, but B&S cannot deny warranty

solely for the lack of receipts or for your failure to ensure the performance of all scheduled mainteĆ

nance.

As the small offĆroad engine owner, you should however be aware that B&S may deny you warranty

coverage if your small offĆroad engine or a part has failed due to abuse, neglect, improper mainteĆ

nance or unapproved modifications.

You are responsible for presenting your small offĆroad engine to an Authorized B&S Service Dealer

as soon as a problem exists. The undisputed warranty repairs should be completed in a reasonable

amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you should contact a

B&S Service Representative at 1Ć414Ć259Ć5262.

The emission warranty is a defects warranty. Defects are judged on normal engine performance.

The warranty is not related to an inĆuse emission test.

Briggs & Stratton Emission Control Defects Warranty Provisions

The following are specific provisions relative to your Emission Control Defects Warranty Coverage. It is in addition to the B&S engine warranty for nonĆregulated engines found in the Operating and Maintenance Instructions.

1. Warranted Parts

Coverage under this warranty extends only to the parts listed below (the emission control

systems parts) to the extent these parts were present on the engine purchased.

a. Fuel Metering System

• Cold start enrichment system (soft choke)

• Carburetor and internal parts

• Fuel Pump

b. Air Induction System

• Air cleaner

• Intake manifold

c. Ignition System

• Spark plug(s)

• Magneto ignition system

d. Catalyst System

• Catalytic converter

• Exhaust manifold

• Air injection system or pulse valve

e. Miscellaneous Items Used in Above Systems

• Vacuum, temperature, position, time sensitive valves and switches

• Connectors and assemblies

2. Length of Coverage

B&S warrants to the initial owner and each subsequent purchaser that the Warranted Parts

shall be free from defects in materials and workmanship which caused the failure of the WarĆ

ranted Parts for a period of two years from the date the engine is delivered to a retail purchaser.

3. No Charge

Repair or replacement of any Warranted Part will be performed at no charge to the owner, inĆ

cluding diagnostic labor which leads to the determination that a Warranted Part is defective, if

the diagnostic work is performed at an Authorized B&S Service Dealer. For emissions warranty

service contact your nearest Authorized B&S Service Dealer as listed in the Yellow Pages"

under Engines, Gasoline," Gasoline Engines," Lawn Mowers," or similar category.

4. Claims and Coverage Exclusions

Warranty claims shall be filed in accordance with the provisions of the B&S Engine Warranty

Policy. Warranty coverage shall be excluded for failures of Warranted Parts which are not origiĆ

nal B&S parts or because of abuse, neglect or improper maintenance as set forth in the B&S

Engine Warranty Policy. B&S is not liable to cover failures of Warranted Parts caused by the

use of addĆon, nonĆoriginal, or modified parts.

5. Maintenance

Any Warranted Part which is not scheduled for replacement as required maintenance or which

is scheduled only for regular inspection to the effect of repair or replace as necessary" shall be

warranted as to defects for the warranty period. Any Warranted Part which is scheduled for

replacement as required maintenance shall be warranted as to defects only for the period of

time up to the first scheduled replacement for that part. Any replacement part that is equivalent

in performance and durability may be used in the performance of any maintenance or repairs.

The owner is responsible for the performance of all required maintenance, as defined in the

B&S Operating and Maintenance Instructions.

6. Consequential Coverage

Coverage hereunder shall extend to the failure of any engine components caused by the failure

of any Warranted Part still under warranty.

Look For Relevant Emission Durability Period and Air Index Information On Your Engine Emission Label

Engines that are certified to meet the California Air Resources Board (CARB) Tier 2 Emission Standards must display information regarding the Emissions Durability Period and the Air Index. Briggs & Stratton

makes this information available to the consumer on our emission labels. The engine label will indicate certification information.

The Emission Durability Period describes the number of hours of actual running time for which the engine is certified to be emission compliant, assuming proper maintenance in accordance with the Operating

& Maintenance Instructions. The following categories are used:

Moderate: Engine is certified to be emission compliant for 125 hours of actual engine running time.

Intermediate: Engine is certified to be emission compliant for 250 hours of actual engine running time.

Extended: Engine is certified to be emission compliant for 500 hours of actual engine running time.

For example, a typical walkĆbehind lawn mower is used 20 to 25 hours per year. Therefore, the Emission Durability Period of an engine with an intermediate rating would equate to 10 to 12 years.

The Air Index is a calculated number describing the relative level of emission for a specific engine family. The lower the Air Index, the cleaner the engine. This information is displayed in graphical form on the

emission label.

After July 1, 2000, Look For Emissions Compliance Period On Engine Emissions Compliance Label

After July 1, 2000 certain Briggs & Stratton engines will be certified to meet the United States Environmental Protection Agency (USEPA) Phase 2 emission standards. For Phase 2 certified engines, the

Emissions Compliance Period referred to on the Emissions Compliance label indicates the number of operating hours for which the engine has been shown to meet Federal emission requirements. For engines

less than 225 cc displacement, Category C = 125 hours, B = 250 hours and A = 500 hours. For engines of 225 cc or more, Category C = 250 hours, B = 500 hours and A = 1000 hours.

The displacement of Model Series 184400 engine is X cc, and 185400 engine is 297cc. The displacement of Model Series 235400 and 245400 engines is 392cc.

This is a generic representation

of the emission label typically

found on a certified engine.

Simplicity 117462-0501-E1 Operating instructions

Related papers

Other documents