Rangemaster GLX390 User manual

Brand: Rangemaster

Model: GLX390

Category: Cooker hoods

Type: User manual

Rangemaster GLX390 is a device designed to eliminate kitchen smells. Its capabilities include:

Four fan speeds, including an intensive speed setting for the strongest cooking vapors
A 24-hour changeover feature that allows for a suction level of 100 m3/h with a noise level of just 28dB(A)
A 30-minute delay feature that enables automatic shutdown to complete the elimination of residual smells
Easy installation with adjustable screws to ensure a level fit
Optional charcoal filter kit for recycling operation

Rangemaster GLX390 is a device designed to eliminate kitchen smells. Its capabilities include:

Four fan speeds, including an intensive speed setting for the strongest cooking vapors
A 24-hour changeover feature that allows for a suction level of 100 m3/h with a noise level of just 28dB(A)
A 30-minute delay feature that enables automatic shutdown to complete the elimination of residual smells
Easy installation with adjustable screws to ensure a level fit
Optional charcoal filter kit for recycling operation

GLX390 Hood

Instructions Manual

www.rangemaster.co.uk

Instructions Manual

INDEX

RECOMMENDATIONS AND SUGGESTIONS......................................................................................................................3

CHARACTERISTICS..............................................................................................................................................................4

INSTALLATION ......................................................................................................................................................................6

USE.........................................................................................................................................................................................9

MAINTENANCE....................................................................................................................................................................10

RECOMMENDATIONS AND SUGGESTIONS

The Instructions for Use apply to several versions of this appliance. Accord-

ingly, you may find descriptions of individual features that do not apply to your

specific appliance.

INSTALLATION

• The manufacturer will not be held liable for any damages resulting from incor-

rect or improper installation.

• Check that the mains voltage corresponds to that indicated on the rating plate

fixed to the inside of the hood.

• For Class I appliances, check that the domestic power supply guarantees ade-

quate earthing.

• Connect the extractor to the exhaust flue through a pipe of minimum diameter

120 mm. The route of the flue must be as short as possible.

• Do not connect the extractor hood to exhaust ducts carrying combustion fumes

(boilers, fireplaces, etc.).

• If the extractor is used in conjunction with non-electrical appliances (e.g. gas

burning appliances), a sufficient degree of aeration must be guaranteed in the

room in order to prevent the backflow of exhaust gas. The kitchen must have

an opening communicating directly with the open air in order to guarantee the

entry of clean air.

USE

• The extractor hood has been designed exclusively for domestic use to elimi-

nate kitchen smells.

• Never use the hood for purposes other than for which it has been designed.

• Never leave high naked flames under the hood when it is in operation.

• Adjust the flame intensity to direct it onto the bottom of the pan only, making

sure that it does not engulf the sides.

• Deep fat fryers must be continuously monitored during use: overheated oil can

burst into flames.

• Do not flambè under the range hood; risk of fire

• This appliance is not intended for use by persons (including children) with re-

duced physical, sensory or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety.

• Children should be supervised to ensure that they do not play with the appli-

ance.

MAINTENANCE

• Switch off or unplug the appliance from the mains supply before carrying out

any maintenance work.

• Clean and/or replace the Filters after the specified time period.

• Clean the hood using a damp cloth and a neutral liquid detergent.

The symbol on the product or on its packaging indicates that this product may not be

treated as household waste. Instead it shall be handed over to the applicable collection point

for the recycling of electrical and electronic equipment. By ensuring this product is disposed

of correctly, you will help prevent potential negative consequences for the environment and

human health, which could otherwise be caused by inappropriate waste handling of this

product. For more detailed information about recycling of this product, please contact your

local city office, your household waste disposal service or the shop where you purchased the

product.

CHARACTERISTICS

Dimensions

1270

MIN. 1390 - MAX. 1600

126

Components

Ref. Q.ty Product Components

1 1 Hood Body, complete with: Controls, Light,

Blower, Filters

2.1 1 Upper Section

2.2 1 Lower Section

8 1 Directional Air Outlet grille

9 1 Flange

10 1 Adapting ring ø 120-125 mm

14.1 2 Air Outlet Connection Extension

15 1 Air Outlet Connection

16 1 Filter cover

Ref. Q.ty Installation Components

7.2.1 2 Upper Chimney Section Fixing Brackets

7.3 1 Air Outlet Connection Support

11 6 Wall Plugs

11a 2 Wall Plugs SB 12/10

12a 6 Screws 4,2 x 44,4

12c 10 Screws 2,9 x 6,5

12d 2 Screws 2,9 x 9,5

Q.ty Documentation

1 Instruction Manual

12a

12c

12d

11a

2.1

2.2

12c

12a

7.2.1 11

7.3

14.1

INSTALLATION

Wall drilling and bracket fixing

7.2.1

1÷2

11a

12a

112+A

A=Min 250

Max 400

710+A

200

180

7.3

On the wall, draw

• a Vertical line up to the ceiling or upper limit, at the centre of the area in which the Hood is

to be fitted;

• a Horizontal line at a minimum of (710 mm + A) above the Cooker Top.

• Mark a point (1) on the horizontal line, 200 mm to the right of the vertical reference line.

• Repeat this operation on the other side, checking that the two marks are level.

• Mark a reference point (2) as indicated at 180 mm from the vertical reference line and (112

mm + A) above the Cooker Top.

• Repeat this operation on the other side, checking that the two marks are level.

• Drill at the points (1) marked, using a ø 12 mm drill bit.

• Drill at the points (2) marked, using a ø 8 mm drill bit.

• Insert the bracket plugs 11a into the holes 1 and screw into place.

• Insert plug 11 into hole 2.

To install a decorative chimney ( optional )

• Place bracket 7.2.1 on the wall as shown about 1-2 mm from the ceiling or upper limit align-

ing the centre (notch) with the vertical reference line.

• Mark the wall at the centres of the holes in the bracket.

• Place bracket 7.2.1 on the wall as shown at X mm below the first bracket (X = height of the

upper chimney section supplied), aligning the centre (notch) with the vertical line.

• Mark the wall at the centres of the holes in the bracket.

• Drill ø 8 mm holes at all the centre points marked.

• Insert the wall plugs 11 in the holes.

• Fix the lower bracket 7.2.1 using the 12a screws (4,2 x 44,4) supplied.

• Fix the upper bracket 7.2.1 and the air outlet connection support 7.3 together using the 2

screws 12a (4,2 x 44,4) supplied.

Mounting the hood body

• Open the ducting panels.

• Disconnect the panel from the hood canopy by slid-

ing the fixing pin lever.(A)

• Remove the metal grease filters by turning the han-

dles provided.

• Adjust the two screws Vr, on brackets 11a, to a mini-

mum.(B)

• Hook the hood canopy onto the two brackets 11a.

• From inside the hood canopy, adjust the screws Vr to

set the Hood Canopy level.

• Tighten the safety screw 11.

(A)

(B)

Connections

DUCTED VERSION AIR EXHAUST SYSTEM

When installing the ducted version, connect the hood to

the chimney using either a flexible or rigid pipe ø 150

or 125 mm, the choice of which is left to the installer.

• To install a ø 125 mm air exhaust connection, insert

the reducer flange 9 on the hood body air outlet and

the adapting ring ø120-125 10 on the reducer flange.

• Fix the pipe in position using sufficient pipe clamps

(not supplied).

• Remove any activated charcoal filters.

ø 125

ø 150

RECYCLING VERSION AIR OUTLET

To install the hood in recycling version, the optional

charcoal filter kit must be purchased.

• Remove the chimney angle bracket.

• Screw the filter cover onto the air outlet, using four

screws 12c (2.9 x 12.5).

• Fix the air outlet grid 8 on the recirculation air outlet

using the 2 screws 12d (2,9 x 9,5) provided.

12c

12d

RECIRCULATION VERSION AIR OUTLET

• Insert the connection extension pieces laterally 14.1 in connec-

tion 15.

• Insert the Connector 15 into the Support bracket 7.3 and fix it

with a screw.

• Make sure that the outlet of the extension pieces 14.1 is hori-

zontally and vertically aligned with the chimney outlets.

• Connect the air outlet connection 15 to the hood body outlet

using either a flexible or rigid pipe ø 150 mm, the choice of

which is left to the installer.

• Ensure that the activated charcoal filters have been inserted.

ø 150

14.1

7.3

Chimney assembly

Upper exhaust Chimney

• Slightly widen the two sides of the upper chimney and hook

them behind the brackets 7.2.1, making sure that they are well

seated.

• Secure the sides to the brackets using the 4 screws 12c (2,9 x

9,5) supplied.

Lower exhaust Chimney

• Slightly widen the two sides of the chimney and hook them

between the upper chimney and the wall, making sure that they

are well seated.

• Fix the lower part laterally to the hood body using the 2 screws

12c (2,9 x 9,5) supplied.

2.1

2.2

7.2.1

12c

2.1

2.2

ELECTRICAL CONNECTION

• Connect the hood to the mains through a two-pole switch hav-

ing a contact gap of at least 3 mm.

• Remove the grease filters (see paragraph Maintenance) being

sure that the connector of the feeding cable is correctly inserted

in the socket placed on the side of the fan.

USE

Control Panel

The hood can be switched on pushing directly onto the requested speed without firstly having

to select 0/1 button.

KEY LED FUNCTIONS

L 0/1 Light Turns lighting on and off.

T1 0/1 Motor on First speed.

When pressed for about 1 seconds the motor

is switched off.

Flashing 24h Changeover

This is enabled by pressing and holding

the button for approximately 5".It al-

lows a suction level of 100 m3/h with a

noise level of just 28dB(A).Can be en-

abled at any speed, even with the hood

turned off.To disable, press and hold

the button for approximately 5".

T2 Speed on Second speed.

Flashing Delay (30')

Press the button for approximately 2" to enable auto-

matic shutdown with a 30' delay. Suitable to complete

elimination of any residual smells. Can be enabled at

any speed and is disabled by pressing the button T1

briefly.

T3 Speed on Third speed.

T4 Speed Fixed Max. speed

Flashing Intensive speed.

Suitable for the strongest cooking vapours and odours.

The function becomes active when the button is

pushed for about 2 seconds. After 10 minutes of func-

tioning it turns off automatically. This function can be

interrupted by means of pressing any of the buttons.

S1 Led Fixed Indicates that the Metal grease filters saturation alarm

has been triggered, and the filters need to be washed.

The alarm is triggered after 100 working hours. (Re-

set; check the Maintenance-paragraph)

Flashing indicates that the activated charcoal odour filter

saturation alarm has been triggered, and the filter has

to be replaced; the metal grease filters must also be

washed. The activated charcoal odour filter is

triggered after 200 working hours. (Activation and

Reset; check the Maintenance-paragraph)

MAINTENANCE

REMOTE CONTROL (OPTIONAL)

The appliance can be controlled using a remote control powered

by a 1.5 V carbon-zinc alkaline batteries of the standard LR03-

AAA type.

• Do not place the remote control near to heat sources.

• Used batteries must be disposed of in the proper manner.

Ducting panels

• Open the ducting panels.

• Disconnect the panel from the hood canopy by sliding the fix-

ing pin lever.

• Clean the outside using a damp cloth and neutral liquid deter-

gent.

• Clean the inside using a damp cloth and neutral detergent; do

not use wet cloths or sponges, or jets of water; do not use abra-

sive substances.

Grease filters

CLEANING METAL SELF- SUPPORTING GREASE FILTERS

Alarm signal reset

• Switch off the lights and extractor motor.

• Press button T3 for at least 3 seconds, until the leds start to

flash.

Cleaning the filters

• The filters are washable and must be cleaned when the LED S1

lights up or at least every 2 months of operation, or more fre-

quently for particularly heavy usage.

• Remove the filters one at a time holding them up with one

hand and pulling the handle downwards with the other hand at

the same time.

• Wash the filters, taking care not to bend them. Allow them to

dry before refitting.

• When refitting the filters, make sure that the handle is visible

on the outside.

Activated charcoal filter (Recirculation version)

The filter is not washable and cannot be regenerated. It must be replaced when led S1 flashes

or at least every 4 months. The alarm signal will only light up when the extractor motor is

switched on.

Alarm signal activation

• In Recirculation version Hoods, the Filter saturation alarm can be enabled on installation or

at a later date. Turn the Lights and the suction Motor off.

• Disconnect the Hood using the Main switch or the double-pole switch on the mains power

supply.

• Restore the connection by pressing and holding T1.

• Release the button. All five LEDs are turned on.

• Within 3 seconds press T1 until LEDs T1 and T4 flash in confirmation:

- LED flashes twice - Activated charcoal filter saturation alarm ENABLED.

- LED flashes once - Activated charcoal filter saturation alarm DISABLED.

REPLACING THE ACTIVATED CHARCOAL FILTER

Alarm signal reset

• Switch off the lights and extractor motor.

• Press button T3 for at least 3 seconds, until the leds start to

flash.

Replacing the Filter

• Remove the metal grease filters

• Remove the saturated activated carbon filters as shown (A).

• Fit the new filters (B).

• Replace the metal grease filters.

Lighting

LIGHT REPLACEMENT

20 W halogen light.

• Remove the light cover by unfastening the screws that hold it.

• Extract the lamp from the Support.

• Replace with another of the same type, making sure that the

two pins are properly inserted in the lamp holder socket holes.

• Replace the light cover.

436004184_ver1

AGA RANGEMASTER LTD.

Rangemaster GLX390 User manual

Brand: Rangemaster

Model: GLX390

Category: Cooker hoods

Type: User manual

Rangemaster GLX390 is a device designed to eliminate kitchen smells. Its capabilities include:

Four fan speeds, including an intensive speed setting for the strongest cooking vapors
A 24-hour changeover feature that allows for a suction level of 100 m3/h with a noise level of just 28dB(A)
A 30-minute delay feature that enables automatic shutdown to complete the elimination of residual smells
Easy installation with adjustable screws to ensure a level fit
Optional charcoal filter kit for recycling operation

Download PDF

report

Rangemaster GLX390 User manual

Rangemaster GLX390 User manual

Related papers

Other documents