Altuscn Hideaway KL3116 User manual

Hideaway™ LCD KVMP Switch

KL3116

User Manual

www.altusen.com

KL3116 User Manual

ii

FCC Information

This is an FCC Class A product. In a domestic environment this product may

cause radio interference in which case the user may be required to take

adequate measures.

This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at his own expense.

RoHS

This product is RoHS compliant.

KL3116 User Manual

iii

User Notice

All information, documentation, and specifications contained in this manual

are subject to change without prior notification by the manufacturer. The

manufacturer makes no representations or warranties, either expressed or

implied, with respect to the contents hereof and specifically disclaims any

warranties as to merchantability or fitness for any particular purpose. Any of

the manufacturer's software described in this manual is sold or licensed `as is'.

Should the programs prove defective following their purchase, the buyer (and

not the manufacturer, its distributor, or its dealer), assumes the entire cost of all

necessary servicing, repair and any incidental or consequential damages

resulting from any defect in the software.

The manufacturer of this system is not responsible for any radio and/or TV

interference caused by unauthorized modifications to this device. It is the

responsibility of the user to correct such interference.

The manufacturer is not responsible for any damage incurred in the operation

of this system if the correct operational voltage setting was not selected prior

to operation. PLEASE VERIFY THAT THE VOLTAGE SETTING IS

CORRECT BEFORE USE.

KL3116 User Manual

iv

Safety Instructions

General

 Read all of these instructions. Save them for future reference.

 Follow all warnings and instructions marked on the device.

 Do not place the device on any unstable surface (cart, stand, table, etc.). If

the device falls, serious damage will result.

 Do not use the device near water.

 Do not place the device near, or over, radiators or heat registers.

 The device cabinet is provided with slots and openings to allow for

adequate ventilation. To ensure reliable operation, and to protect against

overheating, these openings must never be blocked or covered.

 The device should never be placed on a soft surface (bed, sofa, rug, etc.) as

this will block its ventilation openings. Likewise, the device should not be

placed in a built in enclosure unless adequate ventilation has been

provided.

 Never spill liquid of any kind on the device.

 Unplug the device from the wall outlet before cleaning. Do not use liquid

or aerosol cleaners. Use a damp cloth for cleaning.

 The device should be operated from the type of power source indicated on

the marking label. If you are not sure of the type of power available,

consult your dealer or local power company.

 The device is equipped with a 3-wire grounding type plug. This is a safety

feature. If you are unable to insert the plug into the outlet, contact your

electrician to replace your obsolete outlet. Do not attempt to defeat the

purpose of the grounding-type plug. Always follow your local/national

wiring codes.

 Do not allow anything to rest on the power cord or cables. Route the

power cord and cables so that they cannot be stepped on or tripped over.

 If an extension cord is used with this device make sure that the total of the

ampere ratings of all products used on this cord does not exceed the

extension cord ampere rating. Make sure that the total of all products

plugged into the wall outlet does not exceed 15 amperes.

 To help protect your system from sudden, transient increases and

decreases in electrical power, use a surge suppressor, line conditioner, or

uninterruptible power supply (UPS).

KL3116 User Manual

v

 Position system cables and power cables carefully; Be sure that nothing

rests on any cables.

 When connecting or disconnecting power to hot pluggable power supplies,

observe the following guidelines:

 Install the power supply before connecting the power cable to the power

supply.

 Unplug the power cable before removing the power supply.

 If the system has multiple sources of power, disconnect power from the

system by unplugging all power cables from the power supplies.

 Never push objects of any kind into or through cabinet slots. They may

touch dangerous voltage points or short out parts resulting in a risk of fire

or electrical shock.

 Do not attempt to service the device yourself. Refer all servicing to

qualified service personnel.

 If the following conditions occur, unplug the device from the wall outlet

and bring it to qualified service personnel for repair.

 The power cord or plug has become damaged or frayed.

 Liquid has been spilled into the device.

 The device has been exposed to rain or water.

 The device has been dropped, or the cabinet has been damaged.

 The device exhibits a distinct change in performance, indicating a need

for service.

 The device does not operate normally when the operating instructions

are followed.

 Only adjust those controls that are covered in the operating instructions.

Improper adjustment of other controls may result in damage that will

require extensive work by a qualified technician to repair.

KL3116 User Manual

vi

Rack Mounting

 Before working on the rack, make sure that the stabilizers are secured to

the rack, extended to the floor, and that the full weight of the rack rests on

the floor. Install front and side stabilizers on a single rack or front

stabilizers for joined multiple racks before working on the rack.

 Always load the rack from the bottom up, and load the heaviest item in the

rack first.

 Make sure that the rack is level and stable before extending a device from

the rack.

 Use caution when pressing the device rail release latches and sliding a

device into or out of a rack; the slide rails can pinch your fingers.

 After a device is inserted into the rack, carefully extend the rail into a

locking position, and then slide the device into the rack.

 Do not overload the AC supply branch circuit that provides power to the

rack. The total rack load should not exceed 80 percent of the branch circuit

rating.

 Ensure that proper airflow is provided to devices in the rack.

 Do not step on or stand on any device when servicing other devices in a

rack.

KL3116 User Manual

vii

Package Contents

Basic Package

The basic KL3116 package consists of:

1 KL3116 Hideaway

TM

LCD KVMP Switch with Standard Rack Mount Kit

2 Custom KVM Cable Sets

1 Custom Console Cable Set

1 Firmware Upgrade Cable

1Power Cord

1 User Manual*

1 Quick Start Guide

1 Registration Card

Optional Equipment

Depending on any optional equipment that you may have purchased, one of the

following may be included in your package:

 Standard Rack Mount Kit - Long

 Easy Installation Rack Mount Kit - Short

 Easy Installation Rack Mount Kit - Long

Check to make sure that all of the components are present and in good order.

If anything is missing, or was damaged in shipping, contact your dealer.

Read this manual thoroughly and follow the installation and operation

procedures carefully to prevent any damage to the switch or to any other

devices on the KL3116 installation.

* Changes may have been made to the manual since it was printed. Please visit

our website to check for the most up-to-date version.

®

International Co., Ltd.

Manual Part No. PAPE-0262-1AXG

Printing Date: 02/2007

All other brand names and trademarks are the registered property of their respective owners.

KL3116 User Manual

viii

Contents

FCC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

RoHS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

User Notice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

Basic Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

Optional Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi

Online Registration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii

Technical Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii

Chapter 1.

Introduction

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

System Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Computers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Operating Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

KL3116 Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Keyboard Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

LCD Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

KL3116 Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Chapter 2.

Installation

Before you Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Standard Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Single Stage Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Daisy Chaining. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Chapter 3.

Basic Operation

Opening the Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Opening Separately . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Opening Together. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

KL3116 User Manual

ix

Operating Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Closing the Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

LCD OSD Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

The LCD Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

The Adjustment Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Port Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Manual Port Switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Hot Plugging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Switching Station Positions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Hot Plugging KVM Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Powering Off and Restarting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Port ID Numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Chapter 4.

OSD Operation

OSD Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

OSD Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

OSD Main Screen Headings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

OSD Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

F1 GOTO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

F2 LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

F3 SET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

F4 ADM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

F5 SKP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

F6 BRC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

F7 SCAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

F8 LOUT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Chapter 5.

Hotkey Operation

Invoking Hotkey Mode (HKM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

When HKM Is Active . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Hotkey Port Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Selecting the Active Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Auto Scan Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Skip Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

Hotkey Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Alternate Hotkey Invocation Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Alternate OSD Invocation Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Platform Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Miscellaneous Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

Hotkey Summary Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

KL3116 User Manual

x

Chapter 6.

Keyboard Emulation

Mac Keyboard Emulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Sun Keyboard Emulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Chapter 7.

Firmware Upgrade

The Firmware Upgrade Utility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Starting the Upgrade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Upgrade Succeeded . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Upgrade Failed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Firmware Upgrade Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Appendix

Connection Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

OSD Factory Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Clear Login Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Optional Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Dedicated Invocation Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Sun Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Index

KL3116 User Manual

xi

About This Manual

This User Manual is provided to help you get the most from your KL3116

system. It covers all aspects of installation, configuration and operation. An

overview of the information found in the manual is provided below.

Overview

Chapter 1, Introduction, introduces you to the KL3116 system. Its

purpose, features and benefits are presented, and its front and back panel

components are described.

Chapter 2, Installation, describes how to set up your installation. The

necessary steps –

from a basic single stage hookup to a complete daisy chained

operation are provided.

Chapter 3, Basic Operation, explains the fundamental concepts involved

in operating the KL3116.

Chapter 4, OSD Operation, provides a complete description of the

KL3116's On Screen Display (OSD) and how to work with it.

Chapter 5, Hotkey Operation, details all of the concepts and procedures

involved in the Hotkey operation of your KL3116 installation.

Chapter 6, Keyboard Emulation, provides tables that list the PC to Mac

and PC to Sun keyboard emulation mappings.

Chapter 7, Firmware Upgrade, explains how to use this utility to upgrade

the KL3116's firmware with the latest available versions.

An Appendix provides specifications and other technical information

regarding the KL3116.

KL3116 User Manual

xii

Conventions

This manual uses the following conventions:

Monospaced Indicates text that you should key in.

[ ] Indicates keys you should press. For example, [Enter] means to

press the Enter key. If keys need to be chorded, they appear

together in the same bracket with a plus sign between them:

[Ctrl+Alt].

1. Numbered lists represent procedures with sequential steps.

♦

Bullet lists provide information, but do not involve sequential

steps.

→

Indicates selecting the option (on a menu or dialog box, for

example), that comes next. For example, Start

→ Run means to

open the Start menu, and then select Run.

Indicates critical information.

KL3116 User Manual

xiii

ALTUSEN Information

Online Registration

You can register your ALTUSEN product at our online e-Support Center:

http://support.aten.com

Technical Support

When you contact ALTUSEN technical support with a problem, please have

the following information ready:

 Product model number, serial number, and date of purchase

 Your computer configuration, including operating system, revision level,

expansion cards, and software

 Any error messages displayed at the time the error occurred

 The sequence of operations that led up to the error

 Any other information you feel may be of help

North America Technical

Phone Support

Registered ALTUSEN product owners are entitled to

telephone technical support. Call the ALTUSEN

Technical Support Center: 949-453-8885.

International Technical

Phone Support

1. Contact your local dealer.

2. Call the ALTUSEN Technical Support Center:

(886-2) 8692-6959.

Email Support E-mail your questions and concerns to:

[email protected]

Online Support

 Technical Support

 Troubleshooting

 Documentation

 Software Updates

1. Online technical support is available to ALTUSEN

customers through our e-Support Center:

http://support.aten.com

2. Online troubleshooting that describes the most

commonly encountered problems and offers pos-

sible solutions to them; online documentation

(including electronically available manuals); and

the latest drivers and firmware for your product

are available at the ALTUSEN Website:

http://www.aten.com

KL3116 User Manual

xiv

Product Information

For information about all of ALTUSEN's products and how they can help you

connect without limits, visit ALTUSEN on the Web or contact an ALTUSEN

Authorized Reseller.

 In the United States of America, call: 866-ALTUSEN (258-8736)

 In Canada and South America, call: 949-453-8885

 In all other locations, call: 886-2-8692-6789

 Visit ALTUSEN on the Web at http://www.aten.com for a list of locations

and telephone numbers

1

Chapter 1

Introduction

Overview

The KL3116 Hideaway

TM

LCD KVMP Switch is an integrated LCD console

and keyboard, video, and mouse (KVM) switch that offers secure access to 16

attached computers and mounts in only 1U of rack space. It features

independently retractable 17" LCD monitor and keyboard with built-in

touchpad. To maximize space in your data center the keyboard “hides away”

when not in use, while the thin profile LCD monitor reclines flush against the

rack to enable continuous monitoring of computers.

An extra console port is provided on the rear panel to manage the LCD KVM

switch from an external console (monitor, USB keyboard, and USB mouse) up

to 20 meters away. The KL3116 supports both PS/2 and USB keyboards and

mice in the KVM Ports (CPU Ports). For added convenience it also supports an

external PS/2 mouse. The KL3116 supports USB peripheral devices to be used

with the attached computers.

A single KL3116 can control up to 16 computers. As many as 31 additional

KH3116, KH0116, CS-1716, and ACS-1216A KVM switches can be daisy

chained together, so that up to 512 computers can all be controlled from a

single keyboard, monitor, and mouse console.

Your KL3116 investment is protected by an included Firmware Upgrade

Utility. You can stay current with the latest functionality improvements by

downloading firmware update files from our website as they become available,

and using the utility to quickly and conveniently perform the upgrade.

Setup is fast and easy: plugging cables into their appropriate ports is all that is

entailed. Because the KL3116 intercepts keyboard input directly, there is no

software to configure, no need to get involved in complex installation routines,

nor any need to be concerned with incompatibility problems.

Access to any computer connected to the installation is easily accomplished

either by means of a powerful, mouse driven, On Screen Display (OSD) menu

system, or by entering Hotkey combinations from the keyboard. A convenient

Auto Scan feature also permits automatic scanning and monitoring of the

activities of all computers running on the installation one by one.

There is no better way to save time and money than with a KL3116 installation.

By using the KL3116 with its Hideaway™ console to manage your installation,

KL3116 User Manual

2

you: (1) eliminate the expense of having to purchase a separate keyboard,

monitor, and mouse for each computer; (2) save all the space those extra

components would take up; (3) save the space that a keyboard, monitor, and

mouse would take with a standard KVM switch; (4) save on energy costs; and

(5) eliminate the inconvenience and wasted effort involved in constantly

moving from one computer to another.

Features

 Integrated KVM console with 17" LCD monitor in a Hideaway™ housing

 Space saving technology—up to two consoles (one bus) control up to 16

computers

 Extra console port—manage computers in the LCD KVM switch from an

external console (monitor, USB keyboard, and USB mouse)

 Dual interface—supports PS/2 and USB keyboards and mice in the KVM

Ports

 Supports external PS/2 mouse

 USB peripheral support for attached computers

 Conveniently located station and port selectors, each with two 7-segment

LED displays to quickly switch to target computers

 Dedicated Hotkey Mode and OSD Invocation Keys reduce the number of

keystrokes and provide quick access to these functions

 Convenient computer selection via mouse-driven, intuitive On Screen

Display (OSD) menus and Hotkeys

 OSD tree structure makes finding and managing computers easy

 Dual slide—LCD monitor slides independently of the keyboard/touchpad

 Console lock—enables the console draw to remain securely locked away

in position when not in use

 Daisy chain up to 31 additional KH3116, KH0116, CS-1716, and ACS-

1216A KVM switches to control up to 512 computers

 No software required

 Hot pluggable—add or remove computers without powering down the

switch

 OSD port list automatically expands when new stations are added

Chapter 1. Introduction

3

 Auto Scan Mode enables continuous monitoring of user-selected

computers

 Security—Administrator/User password authorization for enhanced

security protection; Administrator access rights synchronized between

master and slave stations

 Two level password security—only authorized users can view and control

computers

 Supports one Administrator and four User accounts with separate profiles

 Broadcast support—commands from the keyboard can be broadcast to all

available computers on the installation

 OSD screen automatically adjusts to resolution changes

 Two types of logout: manual and timed

 Supports Windows, Sun, Linux, Mac, Unix, Netware, AIX (RS6000), and

DOS 6.2 and later

 Hideaway™ housing is slightly less than 1U with top and bottom

clearance for smooth operation in 1U of rack space

 DDC emulation—video settings of each computer are automatically

adjusted for optimal output to the monitor

 Standard 105-key keyboard

 Keyboard status restored when switching computers

 Keyboard and mouse emulation (PS/2 and USB) for smooth switching and

simultaneous booting of multiple computers even when the console focus

is elsewhere

 LCD monitor reclines further to a 10 degree angle

 Superior video quality—supports resolutions up to 1280 x 1024 @ 75Hz

 Upgradable firmware—simultaneously upgrade the firmware for all KVM

switches on the chain via the chaining bus

KL3116 User Manual

4

System Requirements

Computers

The following equipment must be installed on each computer:

 A VGA, SVGA, XGA, or MultiSync video graphics card with an HDB-15

port

Note: The integrated LCD monitor’s maximum resolution is 1280 x 1024

@ 75Hz. Ensure that none of the computer resolution settings

exceed the LCD monitor's maximum resolution.

 PS/2 mouse and keyboard ports (6-pin mini-DIN), or at least one USB port

Cables

Three custom cable sets are provided with this package: one console cable set

for consoles with USB ports, one 2L-5702P KVM cable set for computers with

PS/2 ports, and one 2L-5202U KVM cable set for computers with USB ports.

Use ATEN's high-quality, custom cables to ensure reliable switching among

computers and daisy chained switches. To purchase ATEN’s custom cables

contact your dealer.

Note: We strongly recommend that you use 2L-5702P KVM cable sets for

computers with PS/2 ports. You may use other cables; however, the

keyboard and/or mouse will not work unless all connectors (keyboard,

video, and mouse) are plugged into the ports on the computer before

turning it on. The 2L-5702P cables do not have this limitation.

Function Part Number

KVM Switch to PS/2 Connectors 2L-5702P - 1.8m

2L-5201P - 1.2m

2L-5202P - 1.8m

2L-5203P - 3m

2L-5206P - 6m

KVM Switch to USB Connectors 2L-5201U - 1.2m

2L-5202U - 1.8m

2L-5203U - 3m

2L-5205U - 5m

Daisy Chaining 2L-1700 - 0.6m

2L-1701 - 1.8m

Chapter 1. Introduction

5

Operating Systems

 Microsoft

®

Windows

®

2000 and higher

 Mac OS

®

8.6 and higher

 RED HAT

®

Linux

®

6.0, 7.1, 7.2, 7.3, 8.0 and higher

 Mandriva Linux 9.0 and higher

 SUSE 8.2 and higher

 FreeBSD 3.5.1, 4.2, 4.3, 4.5 and higher

 Sun Solaris™ 8 and higher

 Netware 5.0, 6.0 and higher

 OS/2

 AIX 4 and higher

 DOS 6.2 and higher

KL3116 User Manual

6

KL3116 Front View

No. Component Description

1 Upper Handle Pull to slide the LCD module out; push to slide the module in.

See item 7 in this table and page 19 for more details on

sliding the console in and out.

2 LCD Module See LCD Module, page 8.

3 Keyboard Module See Keyboard Module, page 7.

4 Lower Handle Pull to slide the keyboard/touchpad module out. See item 1

in this table and page 19 for more details on sliding the

console in and out.

5 Power LED Lights (blue) to indicate that the unit is receiving power.

6 Keyboard

Release Catch

These catches (one on each side) release the keyboard/

touchpad module so you can slide it away.

7 LCD Release

Catch

These catches (one on each side) release the LCD module

so you can slide it away.

8 Rack Mounting

Ta bs

The rack mounting tabs located at each corner of the unit

secure the chassis to a system rack. See Standard Rack

Mounting, page 11, for details.

8

6

7

1

5

4

2

3

Page is loading ...

Altuscn Hideaway KL3116 User manual

This manual is also suitable for

Altuscn Hideaway KL3116 User manual

Related papers

Other documents