Edimax Technology PS-3101P User manual

PS-3101P
Edimax Technology
Brand
Edimax Technology
Model
PS-3101P
Category
Network switches
Type
User manual

This manual is also suitable for

0
5
5
/
/
8
8
/
/
1
1
6
6
P
P
o
o
r
r
t
t
s
s
S
S
O
O
H
H
O
O
F
F
a
a
s
s
t
t
E
E
t
t
h
h
e
e
r
r
n
n
e
e
t
t
S
S
w
w
i
i
t
t
c
c
h
h
e
e
s
s
Q
Q
u
u
i
i
c
c
k
k
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
G
G
u
u
i
i
d
d
e
e
Page is loading ...
2
English.
Front Panel & Connectors
Fast Ethernet Switch LED Panel
LED Color Status Description
Lit Power is supplied
PWR
(Power)
Green
Off No power
Lit A valid link is established
Flash Data packets received
LNK/ACT
(Link/Activity)
Green
Off No link is established
Lit This port run at 100Mbps
SPEED
(10/100M)
Yellow
Off This port run at 10Mbps
3
1. Operating Environment
This switching hub must be installed and operated within the
limits of specified operating temperature (32-131°F) and
humidity (10~95% Non-condensing).
z Do not place objects on top of the unit.
z Do not obstruct any vents at the sides of the unit.
z Do not position the unit near any heating source such
as heater, radiator, or direct exposure to sun.
Prevent entering of water and moisture into the unit. If
necessary, use dehumidifier to reduce humidity.
2. Connecting to network devices
The RJ-45 ports on the switch support Auto-MDI/MDI-X
function which allows using straight-through or cross-over
type cables to connect this switch to workstation or hub.
Connect one end of the network cable to the RJ-45 port on
the rear panel, and connect the other end of the network
cable to the RJ-45 port on the network device. Follow the
same procedure to connect all the RJ-45 ports of the switch.
The UTP network cables must comply with EIA/TIA 568
specifications and Category 5 standard for 100Mbps data
transmission. Maximum length: using UTP cable, between
the switch and connected device is 100 meters (300ft).
Once the network cable is connected to both ends and the
attached network device is powered on, the green LNK/ACT
LED should be lit.
3. Connecting the power
Connect the power adapter to the power connector on the
rear panel of the unit; the green Power LED on the front
panel should be lit.
4
Trouble Shooting
1. Power LED is not lit
z Check if the power cord is properly connected to the
external power adapter and the power outlet. Make sure
the DC power jack is firmly plugged into the power socket
of the switch.
2. Link/Activity is not lit when connect to 100Mbps device
z Check the power switch of the network device attached to
the switch; make sure it is turned ON.
z Check the network cable; make sure it is properly
connected to the switch and the network device.
z Check the network cable; make sure the UTP cables
comply with EIA/TIA 568 and Category 5 specification.
[!] Contact your dealer if problem persist.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

Edimax Technology PS-3101P User manual

PS-3101P
Edimax Technology
Brand
Edimax Technology
Model
PS-3101P
Category
Network switches
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents