Ohlins FGKA692 Mounting Instruction

Category
Car kits
Type
Mounting Instruction

Ohlins FGKA692 is an upside-down front fork featuring rebound and compression damping adjusters. With 300mm stroke and 4.4N spring rate, this fork is designed for serious off-road riding. The fork is equipped with 48mm MXF stanchions and a 20mm MX48 preload tube, allowing for precise tuning to suit your riding style and terrain. The kit includes all necessary hardware for installation. Whether you're a professional racer or an enthusiastic trail rider, the Ohlins FGKA692 front fork will provide you with the performance and adjustability you need to tackle any terrain with confidence.

Ohlins FGKA692 is an upside-down front fork featuring rebound and compression damping adjusters. With 300mm stroke and 4.4N spring rate, this fork is designed for serious off-road riding. The fork is equipped with 48mm MXF stanchions and a 20mm MX48 preload tube, allowing for precise tuning to suit your riding style and terrain. The kit includes all necessary hardware for installation. Whether you're a professional racer or an enthusiastic trail rider, the Ohlins FGKA692 front fork will provide you with the performance and adjustability you need to tackle any terrain with confidence.

Mounting Instructions
Öhlins front fork kit FGKA 692
for Kawasaki KX 450 F 2006
Kit Contents
Before installing this front fork kit, please
check the contents of the kit, listed below.
If any part is missing, please contact your
Öhlins dealer.
Please read before installing
Öhlins Racing AB cannot be held responsible
for any damage to the front fork kit, vehicle or
injury to persons, if the instructions for fi tting
and maintenance are not followed exactly.
Similarly, the warranty will become null and
void if the instructions are not adhered to.
Öhlins Racing AB, Box 722, S-194 27 Upplands Väsby, Sweden.
Phone +46 8 590 025 00. Fax +46 8 590 025 80.
www.ohlins.com
FGKA 692 - Issued 2006 01 31
In this manual
Safety precautions
Mounting instructions
Installing the front fork
Installing the springs
Before riding
Set-up data
Adjustments
© Öhlins Racing AB. All rights reserved. Any reprinting or
unauthorized use without the written permission of Öhlins
Racing AB is prohibited. Printed in Sweden.
Front fork 48MXF FGKA692 (1 pair)
Tool for End Cap 01873-01 (1)
Spring 43.6/467/4.3 02428-43 (2)
Spring 43.6/467/4.5 02428-45 (2)
Preload tube 20 mm MX48 02437-20 (2)
Sticker “ÖHLINS” 00197-01 (2)
Sticker Front fork 02332-11 (2)
Öhlins Owners Manual (1)
SAFETY PRECAUTIONS
1 6
Read this manual carefully!
Pay special attention to statements pro-
ceded by the following notations:
The Safety alert symbol means: Attention!
Your safety is involved!
Failure to follow these warning instructions
may result in severe or fatal injury to any-
one working with, inspecting or using this
front fork kit, or to bystanders.
Caution indicates that special precautions
must be taken to avoid damage to the
front fork kit.
Indicates information that is of importance
regarding mounting procedures.
!
WARNING
CAUTION!
NOTE!
WARNING!
1. Installing a front fork, that is not ap-
proved by the vehicle manufacturer,
may affect the vehicle’s stability. Öhlins
Racing AB cannot be held responsible for
any personal injury or damage that may
occur after fi tting the front fork. Contact
an Öhlins dealer or other qualifi ed person
for advice.
2. The vehicle’s service manual must
be referred to when installing this front
fork kit.
3. Please study and make certain you fully
understand the mounting instructions and
the owner’s manual before handling this
front fork kit. If you have any questions
regarding proper installation procedures,
contact an Öhlins dealer or other qualifi ed
person.
!
!
NOTE!
During storage and transportation, espe-
cially at high ambient temperature, the oil
and grease used for assembling may run out
inside the packing and damage the expanded
polystyrene packing material. This is not
unusual and is in no way detrimental to the
front fork kit.
NOTE!
Öhlins products are subject to continuous
improvement and development. Therefore,
although these instructions include the most
up-to-date information available at the time
of printing, there may be minor differences
between your front fork and this manual.
Please consult your Öhlins dealer if you
have any questions regarding the contents
of this manual.
1
Including:
Safety
Tun ing the
suspension
Design
features
Function
Basic
adjustments
Fine tuning
Inspection,
maintenance
Owner’s Manual
Öhlins shock absorbers, MX/ENDURO/OFF ROAD
Your vehicle OEM
ADJUSTMENTS
NOTE!
Read more about compression, rebound
and spring pre-load in your Öhlins Owner’s
manual.
CAUTION!
The front fork springs are delivered separately
and must be installed before the front fork is
mounted to the bike. See section “Installing
springs” in this manual.
Your Öhlins front fork 48MXF is an upside
down type front fork featuring the following
adjusters:
Compression damping adjuster
The compression adjuster is located at the bottom
of the fork leg. Adjust by turning the screw. Use a
slot screw driver.
Rebound damping adjuster
The rebound adjuster is located on the top of
the fork leg. Adjust by turning the screw. Use a
slot screw driver.
Compression
damping
adjustment
Rebound damping
adjuster
NOTE!
When delivered the Öhlins front fork is dialed to
recommended settings for the specifi c brand
and make of the vehicle. If you have changed the
settings, reset according to the following:
The adjusters have a normal right hand thread.
Turn the damping adjusters clockwise to fully
closed (pos. zero [0]). Turn counter clockwise
to open and count the clicks until you reach the
recommended number of clicks. See Setup data
on the last page of this manual.
CAUTION!
Do not use too much force, delicate sealing
surfaces can be damaged.
WARNING!
1. It is advisable to have an Öhlins dealer or other
qualifi ed person install the front fork.
2. Follow the instructions in the vehicle service
manual when changing the front fork.
3. When working on a raised vehicle, make sure that
it is securely supported to prevent it from falling.
1
Put the motorcycle on a workstand to raise the
front wheel off the ground. Ensure the vehicle is
securely supported so that it will not fall over.
2
Remove the front wheel, front leg covers, caliper
protection covers and brake caliper. Let the
brake caliper stay attached to the brake hose.
3
Remove the original front fork legs.
MOUNTING INSTRUCTIONS
25
!
BEFORE RIDING
SET-UP DATA
IMPORTANT NOTICE!
Before riding your bike, check sag and ride
height according to your Öhlins Owner’s
manual.
To get the most out of your suspension com-
ponent it is of great importance to make proper
settings and to use the correct spring for your
weight - full riding equipment on!
We recommend you to read your Öhlins
Owner’s manual carefully to understand the
different effects of the different settings.
NOTE!
Read more about compression and rebound
in your Öhlins Owner’s manual.
Recommended settings
Rebound adjustment 15 clicks
Compression adjustment 12 clicks
Spring pre-load 0 mm
Front fork position 4 mm
Spring rate 4.4 N/mm
Oil level 105 mm
General facts
Front fork length 940 mm
Stroke 300 mm
?
?
? kg
? lbs
7
Align the front fork legs
Put the motorcycle on the ground and compress
the front suspension as hard as possible a few
times. This will align the fork legs.
NOTE!
An alternative way to align the front fork legs
is to rotate the front wheel as fast as possible,
and then bring the wheel to a fast stop, using
the brake.
NOTE!
Before you continue, make sure that the
front fork springs are installed. If they are
not installed, proceed with the instructions
on page 3.
NOTE!
Do not tighten the front wheel axle before the
front fork legs are aligned!
5
Reattach the front leg covers.
6
Put the wheel back in position.
NOTE!
Make sure that all bolts are tightened to the
correct torque, and that nothing restrains
the front fork when the suspension is fully
compressed.
Installing the front fork
Front leg
cover
Front
wheel
Upper triple
clamp
Lower triple
clamp
Brake
caliper
Caliper
protection cover
3
2
2
Make sure
the front
fork legs are
aligned!
Front wheel
Front fork
legs
View from above
Measure fork position
Measure oil level
Measure from the
top of the fork leg
to the top surface of
the triple clamp.
Measure from the
top of the outer leg,
with the top nut
off, fork fully com-
pressed and no
spring installed.
4
Attach the Öhlins front fork legs to the motor-
cycle.
Tighten the torques:
Upper triple clamp: 20 Nm
Lower triple clamp: 10 Nm
CAUTION!
Do not overtighten the triple clamps. The fork
leg tubes can be deformed.
MOUNTING INSTRUCTIONS
3 4
WARNING!
1. It is advisable to have an Öhlins dealer or other
qualifi ed person install the front fork.
2. Follow the instructions in the vehicle service
manual when changing the front fork.
3. When working on a raised vehicle, make sure that
it is securely supported to prevent it from falling.
!
1
Unscrew the top cap, using the top cap tool
1873-01.
Installing the springs
4
Pull out the damper rod until it comes to a
stop.
6
Install the pre-load tube, spring adjuster and the
top cap on the front fork legs.
7
Tighten the top cap, 30 Nm. Use a 17 mm
and a 24 mm wrench, tighten the top cap to
the lock nut by holding the wrenches as in the
gure below.
9
Adjust the compression and the rebound valves
according to the sections: Set-up data and Ad-
justments in this manual.
8
Pull up the fork leg. Attach the top cap to the
fork leg using the top cap tool 1873-01.
NOTE!
The top cap should only be hand tightened!
3
Close the compression and rebound valves. This
will keep the damper rod extended and make it
easier to install the new spring.
Read more about rebound and compression
on page 6, section Adjustments.
Top cap tool
1873-01
Top cap
Fork leg
1
2
5
Top cap
Pre-load
tube
Spring
adjuster
17 mm
wrench
24 mm
wrench
8
7
Top cap tool
1873-01
5
Install the correct springs. In this kit, there are
two pairs of springs provided.
NOTE!
A spring ratio of 4.4 N/mm is obtained by
using a 4.3 N/mm in one leg and a 4.5 N/mm
in the other.
Rebound adjuster
Compression
adjuster
4
2
Pull down the fork leg.
7
6
10
Continue your work according to page 2,
step 4.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Ohlins FGKA692 Mounting Instruction

Category
Car kits
Type
Mounting Instruction

Ohlins FGKA692 is an upside-down front fork featuring rebound and compression damping adjusters. With 300mm stroke and 4.4N spring rate, this fork is designed for serious off-road riding. The fork is equipped with 48mm MXF stanchions and a 20mm MX48 preload tube, allowing for precise tuning to suit your riding style and terrain. The kit includes all necessary hardware for installation. Whether you're a professional racer or an enthusiastic trail rider, the Ohlins FGKA692 front fork will provide you with the performance and adjustability you need to tackle any terrain with confidence.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI