2. Zeiss
  3. Sigma 300
Sigma 300

Zeiss Sigma 300 Installation guide

  • Hello! I've read the Installation Requirements document for the ZEISS RISE Microscopy, which includes Raman Imaging and Scanning Electron microscopy. This document specifies environmental, location, electrical, safety and transport needs for the product. I can answer your questions regarding this equipment.
  • What is the laser safety classification of the Raman equipment?
    What are the recommended room size for the system?
    What are the power requirements?
Installation Requirements
ZEISS RISE Microscopy (Raman Imaging and Scanning
Electron microscopy)
ZEISS RISE Microscopy (Raman Imaging and Scanning Electron microscopy)
Original Manual
Carl Zeiss Microscopy GmbH
Carl-Zeiss-Promenade 10
07745 Jena
Germany
[email protected]
www.zeiss.com/microscopy
Carl Zeiss Microscopy GmbH
Carl-Zeiss-Promenade 10
07745 Jena
Germany
Document Name: Installation Requirements ZEISS RISE Microscopy (Raman Imaging and Scanning
Electron microscopy)
Order Number: 349500-8193-000
Revision: 1
Language: en-US
Effective from: 01/2022
© 2022 Without the prior written consent of ZEISS, this document or any part of it must neither be translated nor reproduced or
transmitted in any form or by any means - including electronic or mechanic methods, by photocopying, recording or by any in-
formation or filing system. The right to make backup-copies for archiving purposes shall remain unaffected thereby. Any viola-
tions may be prosecuted as copyright infringements.
The use of general descriptive names, registered names, trademarks, etc. in this document does not imply that such names are
exempt from the relevant intellectual property laws and regulations and therefore free for general use. This shall also apply if
this is not specifically referred to. Software programs shall entirely remain the property of ZEISS. No program or subsequent up-
grade thereof may be disclosed to any third party, copied or reproduced in any other form without the prior written consent of
ZEISS, even if these copies or reproductions are destined for internal use at the customer's only, the only exception being one
single back-up copy for archiving purposes.
ZEISS Table of Contents
Table of Contents
1 Installation Requirements Option ................................................... 4
2 Requirements.................................................................................. 5
2.1 Environmental Requirements............................................................................... 5
2.2 Location Requirements........................................................................................ 5
2.2.1 Space Requirements.............................................................................. 5
2.3 Electrical Supplies................................................................................................ 6
2.4 Safety and Radiation Information........................................................................ 7
2.4.1 Laser Safety........................................................................................... 7
2.5 Transport and Storage ........................................................................................ 7
2.5.1 Weight and Sizes .................................................................................. 7
2.5.2 Weight and Sizes of the Transported Goods.......................................... 8
3 Applicable Standards and Regulations............................................ 9
Space for Comments....................................................................... 10
4 Responsibility Checklist for the ZEISS Crossbeam RISE Microscopy 11
Installation Requirements ZEISS RISE Microscopy (Raman Imaging and Scanning Electron microscopy) | en-US | Rev. 1 |
349500-8193-000
3
1 Installation Requirements Option ZEISS
1 Installation Requirements Option
Option-specific installation requirements are provided as separate documents, as the options
could be supplied together with a new microscope or as an upgrade on an already installed mi-
croscope. This document is to be used together with the main microscope installation require-
ments document. Also consult ZEISS regarding conflicting information given in the installation re-
quirements for the microscope and the option. It may be required to change an existing installa-
tion of a microscope when an option is added, e.g. adequate space is required or an additional
mains electricity supply. Furthermore, adding an option on the microscope may introduce interfer-
ence on the image of the microscope.
4 Installation Requirements ZEISS RISE Microscopy (Raman Imaging and Scanning Electron microscopy) | en-US | Rev. 1 |
349500-8193-000
ZEISS 2 Requirements | 2.1 Environmental Requirements
2 Requirements
The following sections describe each requirement in detail.
2.1 Environmental Requirements
The RISE option does not require any specific environmental conditions. The environmental speci-
fications for the main microscope apply to the whole system.
Please also refer to the installation requirements of the microscope for detailed information about
environmental requirements. A site survey can be requested from your local ZEISS service repre-
sentative prior to the installation.
2.2 Location Requirements
If a microscope is to be delivered with additional options, please discuss the additional require-
ments for these options with a ZEISS service representative. The options may require additional
health and safety considerations, space, power points or other resources.
The microscope and options must only be operated in closed rooms. The microscope should not
be installed near radiators or windows with direct sunlight.
Compliance with the installation requirements of the microscope and the availability of the re-
quested supplies is the responsibility of the customer and has to be readily available at the time of
installation.
Installation site Exclusively inside buildings
Operating range ≤ 2000 m above sea level
Info
Harmful gases and fumes that may be used on the microscope must be safely extracted from
the microscope and site in accordance with local safety regulations.
The microscope must not be set up in areas with potential danger by explosives.
2.2.1 Space Requirements
Recommended room size Min. 4.0mx5.0mx2.3m
Service and safety clearance area Min. 0.75m at each side
Note: Some detectors require a longer dis-
tance between the wall and the left hand
side of the SEM.
Entrance Min. 0.8m wide
The Raman system uses a 2m USB cable from the control unit to the Raman system PC. The Ra-
man power and control unit is placed on the left-hand side of the Sigma SEM and the spectrome-
ter is installed on the left WDX port of the Sigma SEM. Therefore moving the Raman power and
control unit to access the left panel of the SEM is limited due to cable and fiber optic lengths.
The following layouts are recommended for optimal accessibility, airflow and stability, depending
on the options purchased with the system. For possible changes in preferential layout, please dis-
cuss with your ZEISS representative. The placing of the user table can vary depending on available
space and cable lengths.
Installation Requirements ZEISS RISE Microscopy (Raman Imaging and Scanning Electron microscopy) | en-US | Rev. 1 |
349500-8193-000
5
2 Requirements | 2.3 Electrical Supplies ZEISS
1826
1
Front View
Top View
Side View
2
3
4
Fig.1: Floorplan RISE
1Raman power and control unit 2Spectrometer
3SEM PC 4Raman system PC
2.3 Electrical Supplies
It is recommended to install a surge protector on the Raman to prevent intense voltage spikes at
startup.
6 Installation Requirements ZEISS RISE Microscopy (Raman Imaging and Scanning Electron microscopy) | en-US | Rev. 1 |
349500-8193-000
ZEISS 2 Requirements | 2.4 Safety and Radiation Information
Value
Power requirements 2 x L1/N/PE 230 VAC ± 10% 16A
Nominal AC voltage L1/N/PE 230 VAC ± 10 %
Nominal frequency 50 - 60 Hz
System connection Length of cable and fibers required
Single mode fibers: 3m (to connect the lasers
with the back of the microscope)
Multi mode fibers: 3m (to connect the top of
the microscope with the spectrometer)
USB cable: 2m (to connect the control unit
to the PC)
Max. power consumption 2 power points are required
Power 1: Control unit, spectrometer and
camera: 520W
Per laser: 100W
Power 2: PC and monitor 500W
2.4 Safety and Radiation Information
2.4.1 Laser Safety
The Raman equipment is classified as laser class 3B / IIIB, as laser class 3B radiation is generated in
the system. The operator of the laser equipment is responsible for conformance with protective
measures and safety requirements.
Laser safety measures in accordance with the applicable country-specific legal regulations remain
valid. As the responsible body, the operator is responsible for complying with laser safety regula-
tions.
LASER RADIATION
WHEN OPEN.
AVOID EXPOSURE
TO THE BEAM
WARNING - CLASS 3B
2.5 Transport and Storage
Allowable
temperature
Allowable temperature during on-site storage and transport:
§Between 10°C and 30°C
§Relative humidity less than 65%
2.5.1 Weight and Sizes
Component Weight (kg)
Raman equipment stand-alone 140
Installation Requirements ZEISS RISE Microscopy (Raman Imaging and Scanning Electron microscopy) | en-US | Rev. 1 |
349500-8193-000
7
2 Requirements | 2.5 Transport and Storage ZEISS
2.5.2 Weight and Sizes of the Transported Goods
Main Components Length
(mm)
Width
(mm)
Height
(mm)
Weight (kg)
Console and accessories** 1450 1360 1180 Appr. 348
Spectrometer 840 505 270 26
Laser 785 305 325 Appr. 9
Controller 640 585 710 Appr. 50
Optical components, cou-
plers
490 400 325 Appr. 50
Microscope head 645 575 445 Appr. 21
PC 490 225 535 Appr. 10
Keyboard 495 210 45 Appr. 0.5
Screen 650 220 450 Appr. 6.5
Cables 430 105 130 Appr. 1.0
Cables, optical fibre spec-
trometer
4350 300 75 Appr. 0.5
Tools and power supply, ca-
bles, performance sheets
350 300 75 Appr. 2.0
Power supplies, objective 350 300 75 Appr. 2.0
PC accessories 330 270 55 Appr. 0.5
White light source 265 210 125 Appr. 1.0
**Console, damper, monitors, cables, pipes &c. are wrapped and packed in separate cartons and
shipped in a separate box.
8 Installation Requirements ZEISS RISE Microscopy (Raman Imaging and Scanning Electron microscopy) | en-US | Rev. 1 |
349500-8193-000
ZEISS 3 Applicable Standards and Regulations
3 Applicable Standards and Regulations
Observe all general and country-specific safety regulations as well as applicable environmental
protection laws and regulations.
Please refer to the installation requirements of the microscope for information about compliance
with regulations and directives.
Installation Requirements ZEISS RISE Microscopy (Raman Imaging and Scanning Electron microscopy) | en-US | Rev. 1 |
349500-8193-000
9
Space for Comments ZEISS
Space for Comments
10 Installation Requirements ZEISS RISE Microscopy (Raman Imaging and Scanning Electron microscopy) | en-US | Rev. 1 |
349500-8193-000
ZEISS 4 Responsibility Checklist for the ZEISS Crossbeam RISE Microscopy
4 Responsibility Checklist for the ZEISS Crossbeam
RISE Microscopy
Company name:
Address:
Contact person:
Requirements Fulfillment Comments
Yes
(Checked
and com-
plete)
Partially
(Partially ful-
filled)
No
(Checked
but not ful-
filled)
N/A
(not applica-
ble)
Designate a health
and safety person
Operator is responsi-
ble for complying with
laser safety regulations
for laser class 3B
Room temperature
and humidity (< 65 %
humidity)
Room dimensions suit-
able to recommended
layouts
Main microscope in-
stallation requirements
document has been
read
Safety issues have
been read
Compliance with laser
safety regulations
Place, date Name Signature
The above signature conveys that the Installation Requirements have been read and understood. The customer fur-
ther understands that some of these requirements are necessary to help assure the safety of personnel, or to prevent
damage to the equipment or the facility. The customer further understands that some of the requirements must be
fulfilled in order for the equipment to meet its full performance capabilities and for the equipment to be successfully
installed.
Comments:
Installation Requirements ZEISS RISE Microscopy (Raman Imaging and Scanning Electron microscopy) | en-US | Rev. 1 |
349500-8193-000
11
Carl Zeiss Microscopy GmbH
Carl-Zeiss-Promenade 10
07745 Jena
Germany
phone: +49 1803 33 63 34
fax: +49 3641 64 3439
[email protected]
www.zeiss.com/microscopy
Installation Requirements ZEISS RISE Microscopy (Raman Imaging and Scanning Electron microscopy) | en-US | Rev. 1
Modifications reserved. | Printed in Germany
/