Bryston PowerPac 60 Owner's manual

Brand: Bryston

Model: PowerPac 60

Type: Owner's manual

Bryston PowerPac 60 is a monaural power amplifier designed for applications where portability, quality, and flexibility are essential. With 60 Watts of power at 8 Ohms, it's perfect for use as a modular power amplifier or for multi-room audio systems. It features both balanced and unbalanced inputs, gold-plated connectors, and a soft-start power supply. The PowerPac 60 is also compact and lightweight, making it easy to install in tight spaces.

BRYSTON

OWNER’S MANUAL

Monaural Amplifiers

PowerPac 60/120/250

Instructions For Bryston

GENERAL INSTRUCTIONS

Setup Recommendations:

Description:

General Information:

Thank you for choosing a Bryston

product. We would welcome any comments

or suggestions you may have regarding the

operation of your amplifier. We consider our

customer to be Bryston,s most important re-

source and your opinion is very much appre-

ciated. In the unlikely event you have a prob-

lem with your amplifier and must return it for

service please keep the original box and all

packaging material.

The Bryston PowerPac 60/120/250

are high quality modular single channel

60/120 /250 watt power amplifier intended for

use in applications where portability, quality

and flexibility are of prime importance.

The PowerPac is a perfect choice for

use as a modular power amplifier which can

be attached directly to the rear of your loud-

speaker . It can also be bolted on the wall, or

in the wall, for utilization in audio/video sur-

round systems (left/right/center/rears) where

a non-conspicuous power module is required.

Another application would be in multi-room

audio systems where single or multiple ampli-

fiers are needed to provide music to other

rooms.

We recommend that you do not place

the amplifier in a totally enclosed area. Allow

some space at the top, sides as your Bryston

amplifier relies on convection cooling and

some air flow is desirable.

Make sure the power switch on the

front panel of the amplifier is in the off (out)

position. Plug the power cord into the front

panel of the amplifier, then insert the male

end into the wall outlet.

All Bryston amplifiers contain high

quality, dedicated circuitry in the power sup-

plies to reject RF, line spikes and other

power-line problems.

Bryston power amplifiers do not re-

quire specialized power line conditioners.

Plug the amplifier directly into its own wall

socket.

Connect your loudspeakers ensuring

that the positive (red) and ground (black) ter-

minals on your amplifier are connected to the

positive and ground terminals on your loud-

speakers.

Note: Make sure that the front panel

switch for choosing balanced or non-

balanced is in the correct position.

The Bryston PowerPac 60 monaural

amplifier consist of two of Bryston’s custom

power transistors as output devices. The

power output is 60 Watts @ 8 Ohms.

The Bryston PowerPac 120 monaural

amplifier consist of four of Bryston’s custom

power transistors as output devices. The

power output is 120 Watts @ 8 Ohms.

The Bryston PowerPac 250 monaural

amplifier consist of eight of Bryston’s custom

power transistors as output devices. The

power output is 250 Watts @ 8 Ohms.

Dimensions PP60: (LHW) 12 X 1.8 X 7.1 Inches,

30.5 x 4.6 x 17.9 cm.

Weight 5.7 Lbs/2.6Kg.

Dimensions PP120: (LHW) 12 X 4.3 X 7 Inches,

30.5 x 10.9 x 17.8 cm.

Weight 10.6 Lbs/4.8Kg.

Dimensions PP250: (LHW) 17 X 4.5 X 8.4 Inches,

43 x 11.5 x 21 cm.

Weight 23 Lbs/10.5Kg.

BRYSTON POWERPAC 60/120/250

Grounding and Ground LIft Switch (except PP250):

Input and Output Connectors:

Bryston PowerPac amplifiers come

standard with two input connectors: one un-

balanced RCA/phono connector and a bal-

anced combination XLR - 1/4-inch jack with

fully discrete active input circuitry.

All input connectors are gold-plated

and should only be used only with high-

quality, gold-plated interconnect cable as a

poorly plated connector will eventually cor-

rode through the gold flash.

Bryston offers interconnect cables

with heavily gold plated, quality connectors

available through any Bryston authorized

dealer or directly from Bryston.

Output connectors consist of one

pair of five-way binding post terminals (1

red and 1 black) that can accept either

standard banana plugs, spade lugs, pins or

bare wire. Since the binding posts are gold-

plated, we recommend gold plated connec-

tors also be used on the speaker cables.

All Bryston amplifiers will accept bal-

anced or single-ended (RCA) input connec-

tors. The balanced inputs use combination

3-pin XLR (pin-1-ground), (pin-2-+) and

1/4-inch tip-(+), ring and sleeve (ground)

input connectors.

A ground lift switch is located on the

front panel of the amplifier. It is connected

between the chassis ground (including the

third prong on the power cord) and the signal

ground.

This switch is normally left in the con-

nected (up) position. Occasionally a multi-

amplifier installation or an unusual grounding

situation with another component (CD player,

video recorder, television etc.) will cause a

ground loop between the signal ground and

the chassis ground. This switch will reduce

the resultant hum in many cases without re-

sorting to a “ cheater plug ” by switching to

the separated (down) position.

Note: this switch does not disconnect the

chassis from the third prong on the power

cord which must be left intact for safety

reasons.

POWERPAC 60/250 ONLY

Dual colour LED pilot lights indicating GREEN at normal level, flashing RED at clipping.

SPECIAL INSTRUCTIONS

The PowerPac 120/250 remote on/off

function allows the user to link the power

on/off of an amplifier, or group of amplifi-

ers, to an external preamp, or other control

product. This is useful in installations, such

as home theater, which usually present a

convenience problem for powering up mul-

tiple amplifiers, often at distant locations

from the source.

Located on the front panel of the

PowerPac 120/250 (see illustration), is a

two terminal 12 volts (active range 9 -12

volts AC or DC of either polarity), input

connector and a potentiometer. The

PowerPac amplifiers can then be powered-

up by an external 12-volt signal connected

to the terminals of the jack.

This jack will accept 1/4 -inch stripped

wire ends, inserted into the square holes

provided, and the adjacent screws care-

fully tightened to hold them in place. The

internal "delay" turn-on circuit, will delay

turn–on between 1 and 10 seconds, follow-

ing application of the 12-Volts. In this way

groups of amplifiers may be sequenced on

to distribute power surges over a period of

time.

The power switch must be left in the

“off” position, at all times for the

PP120 amplifier to operate in the re-

mote mode.

The PP250 has a 3-position switch al-

lowing for ‘Local (on)’ or ‘Off ‘or ‘REM

(remote)’ power selection.

The amplifier will remain powered-up

while the 12-Volt signal is present, and

will turn off when the 12-Volt signal is

switched off.

Input sensitivity is selectable using the

‘INPUT’ slide switch. In the BAL REG posi-

tion, 2 Volts in will give 100 Watts into 8

ohms at the output. This is the recom-

mended setting when using Bryston pre-

amplifiers or other pre-amplifiers having ac-

tive balanced outputs. This setting also pro-

duces the lowest noise floor.

The ‘BAL +6 dB” setting adds 6 dB of gain

to provide an input sensitivity of 1 Volt in =

100 Watts / 8 ohms at the output for outputs

that are transformer coupled, or low level

sources.

The ‘UNBAL’ setting selects the gold plated

‘phono’ type connector. The input impedance is

50K ohms.

POWERPAC 120/250

PUSH

PowerPac 250 PowerPac 120 PowerPac 60

250 watts into 8 ohms 120W/8 ohms 60W/8 ohms

400 watts into 4 ohms 200W/4 ohms 100W/4 ohms

Gain

29dB (Unbalanced) 29dB (Unbalanced) 29dB (Unbalanced)

23dB or 29dB (Balanced) 23dB or 29dB (Balanced) 23dB (Reg.Balanced)

29dB (Pro-balanced)

Distortion

IM or THD at nominal output power < 0.007% from 20Hz to 20kHz

Noise

>106dB below rated output

Power Bandwidth

<1 Hz to over 100 kHz

Input Sensitivity

Unbalanced 1.5 volts in = Unbalanced 1 Volts in = Unbalanced 0.75 Volts in =

250 watts into 8 ohms 100 watts at 8 ohms 60 watts at 8 Ohms

Input Impedance

50K ohms unbalanced

20K ohms balanced

Heatsinking

Over 2,640 cm/square Over 1550 cm/square Over 600 cm/square

Features

Regulated power supplies to all voltage gain stages

Gold plated input and output connectors

Switchable balanced XLR - 1/4" w/ two different gains and RCA unbalanced inputs only for PP250 & PP120

Remote power turn-on 12V, AC/DC only for PP250 & PP120

Power Clipping Indicator only for PP120 & PP60

Soft start Power supply only for PP250

Dimensions

LxHxW = 17"x4.5"x8.4" 12"x4.3"x7" 12"x1.8"x7.1"

43x11.5x21 Cm 30.5x10.9x17.8 Cm 30.5x4.6x17.9 Cm

wt: 23 lbs 10.6 lbs 5.7 lbs

wt:10.5 kg 4.8 Kg. 2.6 Kg.

BRYSTON PowerP ac SPECIFICATIONS

BRYSTON 20 -YEAR WARRANTY

Bryston products are warranted to be free

from manufacturing defects for a minimum

of twenty years from the original date of

manufacture. This includes parts, labour

and return shipping to the first owner and

all subsequent owners. Warranty coverage

is automatic and commences with the

original date of manufacture which is kept

on file at Bryston.

In the event of a defect or malfunction,

Bryston will remedy the problem by repair

or replacement, as we deem necessary, to

restore the product to full performance.

This warranty is considered void if the

defect, malfunction or failure of the

product or any component part was

caused by damage (not resulting from a

defect or malfunction) or abuse while in

the possession of the customer, tampering

by persons other than factory-authorized

service personnel, or failure to comply

with Bryston operating instructions.

This warranty gives you specific legal

rights and you may also have other rights

which may vary from province to province

and country to country.

BRYSTON SERVICE IN CANADA:

24 STEINWAY BLVD., UNIT 48

ETOBICOKE, ONTARIO

M9W 6T8

PHONE: 416-675-2585

FAX: 416-675-3103

BRYSTON SERVICE IN UNITED STATES:

30 COVENTRY STREET,

NEWPORT, VERMONT Suite 5.

05855

PHONE: 802-334-1201

FAX: 802-334-1201

BRYSTON LTD.

P.O. BOX 2170

677 NEAL DRIVE

PETERBOROUGH, ONTARIO

CANADA.

K9J 7Y4.

PHONE: 705-742-5325

FAX: 705-742-0882

www. bryston.ca

Bryston PowerPac 60 Owner's manual

Bryston PowerPac 60 Owner's manual

Bryston PowerPac 60 Owner's manual

Related papers

Other documents