2. Anviz
  3. M-Bio
M-Bio

Anviz M-Bio User guide

  • Hello! I've reviewed the user guide for the Anviz M-Bio Desktop and Wireless Fingerprint and Card Terminal. This guide covers everything from the package contents to registering users and using the device's web server. I'm ready to answer any questions you have about using your device.
  • What should I do if the package is missing items?
    What type of power supply should I use?
    How do I delete a user from the device?
POWERING A SMARTER WORLD
POWERING A SMARTER WORLD
Desktop and Wireless Fingerprint
and Card Terminal
M-Bio
Quick Guide RFID Card
X4
USB Cable Quick Guide Device
Notification:
1. Please check if the package contains all the items listed above.
Contact the distributor if there is any problem.
2. Please keep the product away from the magnetic field, and avoid
causing any damage to the device.
3. Please use the original power supply or refer to the instruction to get
the right power supply.
4. Please strictly follow the instructions to install the product. Any
damage to it caused by incorrect operation and wiring are not
under warranty.
Package List
1
POWERING A SMARTER WORLD
Outdoor Fingerprint & Card
Reader/Controller
M-Bio
Quick Guide POWERING A SMARTER WORLD
Illustration for Placing Finger
Always place finger in
the center of the sensor.
Try to place your finger covers the entire sensor.
Correct Method
Incorrect Method
DO NOT slide your finger
during the fingerpint
verification process.
DO NOT just use your fingertip.
DO NOT place finger
at an angle.
DO NOT place finger away from
the center of the sensor.
the sensor backlight turns off.
DO NOT take off finger during
the fingerprint verification
process.
( Straighten your finger and then place it on the sensor Ensure the
finger is flat and covers the entire sensor)
2
Appearance
192.168.2.234AP
2021 01 10
14:20:33
3
OLED Screen
Fingerprint Sensor
Fingerprint Sensor
Power Over USB Port
Power Button
Date and Time
Bluetooth
WIFI AP Mode
Battery
Operation Guide Operation Guide
IMPORTANT:
Register User:
1. Swipe
Enroll Card
Exit
Enrollment
Add One Fingerprint per User Only:
Green
& Blue
lights up
2. Place finger 3. Place finger
again
Blue LED and
fingerprint sensor
lights up
Green LED lights up
and display Save
Successed
4. Continue to register another user
Green
& Blue
lights up
2. Swipe
User Card 3. Swipe User
Card again
Note: 1. After finish enrolling current user,
the device will continue to register another user.
2. After finish enrollment, please swipe
enroll card to exit enroll status.
Notice:
During the device in the regsiter mode without
any operation for 3 sec the M-bio will back to the
normal mode.
Add Card Only:
5. Swipe Enroll
Card to end
the enrollment
Notice:
1. Swipe
Enroll Card
Note: 1. After finish enrolling current user,
5. Swipe Enroll Card
to end the enrollment.
4. Continue to register another user
Exit
Enrollment
M-Bio is suitable for USB 5V power supply only. Power on the device still the device screen display
as below:
Blue LED and
fingerprint sensor
lights up
Green LED lights up
and display Save
Successed
2. After finish enrollment, please swipe
enroll card to exit enroll status.
Delete Card:
Notice:
2. Swipe
User Card 3. Swipe User
Card again
4. Continue to delete
1. Swipe
Delete Card
5. Swipe Delete
Card to end
the process
After delete one user, you can continue to delete
another user or swipe Delete Card to exit delete mode.
Red and Blue
LED Light
Up
Blue LED and
FingerPrint sensor
lights up
Green LED lights up
and display delete success
Delete User:
Delete Fingerprint or Card
Red and Blue
LED Light
Up
4. Continue to delete
After delete one user, you can continue to delete
another user or swipe Delete Card to exit delete mode.
5. Swipe Delete
Card to end
the process
1. Swipe
Delete Card Green LED lights up
and display delete success
Blue LED and
FingerPrint sensor
lights up
2. Place finger 3. Place finger
again
Notice:
During the device in the delete mode
without any operation for 3 sec the M-bio
will back to the normal mode.
During the device in the regsiter mode without
any operation for 3 sec the M-bio will back to the
normal mode.
45
When you swipe card on M5 Pro, Red
LED flashing with long beeps means the
card does not exist in the device.
Google
CrossChex Mobile App Anviz
https://bit.ly/2Vn0wh6 https://bit.ly/2J9qA95
In order to protect the environment, Anviz has decided to go "CD Free"
campaign since June 1st 2019. We will provide QR code for you to download
the electronic documents to make sure that you understand how to install
and use Anviz devices.
1
202101
Login WebServer
Anviz brand and product are trademarked and protected under law of the United States.
Unauthorized use is prohibited.
For more information, please visit www.anviz.com , or send email to [email protected] for more help.
©2021 Anviz Global Inc. All Rights Reserved.
6
 
         
User: 1/10000 Record: 6/100000
User Network Basic Setting Advance Setting
192.168.2.1
AP
2021 01 10
14:20:33
Login to M-bio Webserver to manage
the device.
M-bio is default with WIFI AP funciton.
Please connect M-Bio WIFI AP
WIFI SSID: M-bio
Default Password: 123456789
The Webserver Login Account: admin Password: 12345
/