eSSL FL-300 User manual

Type
User manual

eSSL FL-300 is an intelligent fingerprint door lock that offers multiple ways to access: fingerprint, pin code, RFID card, & mechanical key. With advanced semiconductor sensors and a 360° scanner, it provides accurate and secure fingerprint recognition. It supports multiple users, including 5 master users and 85 normal users for fingerprint access, 5 master users and 15 normal users for pin code access, and 99 normal users for RFID card access. This lock also features dual authentication mode for added security, where two different methods are required to open the door.

eSSL FL-300 is an intelligent fingerprint door lock that offers multiple ways to access: fingerprint, pin code, RFID card, & mechanical key. With advanced semiconductor sensors and a 360° scanner, it provides accurate and secure fingerprint recognition. It supports multiple users, including 5 master users and 85 normal users for fingerprint access, 5 master users and 15 normal users for pin code access, and 99 normal users for RFID card access. This lock also features dual authentication mode for added security, where two different methods are required to open the door.

User Manual
FL-300
www.esslsecurity.com
Intelligent Fingerprint Door Locks
Fingerprint Sensor
Product Layout:
Please keep internal/external panel clean before installation.
.
Panel and lock body installation steps.
1. Adjust handle ball according to door open way.
2. Lock body installation: Put lock body into guard hole and lock body cable should go
though spindle hole to inside door and last tighten screw.
3. Put stud onto front panel connection screw and put spring into spindle hole.
4.Put spindle into lock body(follow drawing), take data line from above lock body into
inside door, spindle and stud should be in corresponding hole, front panel should be
compactly installed on the door.
5.Connect the main board cable to the corresponding interface of the back pane make
sure spindle, handle ball core into corresponding position, tighten back panel onto
the door and tight panel installation screw.
6.Adjust inside and outside panel verticality and tight screw put plug in.
7.Install battery cover, try opening by fingerprint, RFID card or pin code or manual key.
Reset Button
(long press 5 second)/
Inside Panel Button
(1 push open)
Panel Screw Hole
Battery Box
Handle Nob
Battery Cover
Panel Screw Hole
When change battery, push bulge on
battery cover then take off battery cover
L open way put screw in L screw hole and R
open way put into R screw hole
Battery cover
Fingerprint Scanner
Key Pad
RFID Scanner
USB External
Power Port
Key Hole
Cylinder Cover
Inside panel install screw Outside panel
Connection screw
Lock body screw
Buckle
Button box
Buckle and button
box should be fit
lock body screw
Lock body screw
Spindle
Connection screw
Cylinder
Inside panel install screw
Battery Cover
Inside panel
Handleball
Rubber plug
Wire hole
Spindle hole
Spring
User Addition:
1. Reset factory default: Press RESET at back of lock for 5 seconds,
voice will prompt reset succeed.
2. Register master/user:
2.1 Initial mode: Touch screen key pad for lights on and press # for
2 seconds and voice prompts addtions of master code.
2.2 Once master user is added:
a. Add new master: Touch screen for lights on and press #
for 2 seconds, voice prompts confirm master, input any registered
master and press # again to add master user (fingerprint /password)
b. Add new common user: Touch screen for lights on and press # for
2 seconds input any registered master user “and” voice prompts
“add user” to add new fingerprint, password and card etc.
3. Addition of “One Time password or Guest password”: Users
can be added for with password access which will provided
access one time and will expire after its used.
3. Delete registered fingerprint/card/password:
3.1. Deleting individual fingerprint: Touch screen for lights on & long press
1 for 2 seconds. After voice prompts input fingerprint to delete, press
fingerprint on scanner to delete.
3.2. Deleting by user numbers: Touch screen for lights on & long press 1
for 2 seconds. After voice prompts input fingerprint code to delete
enter user number of fingerprint to delete.
3.3. Delete all cards: Touch screen for lights on & long press 2 for 2
seconds press # to enter in to delete all cards option and # again to
confirm deletion.
3.4. Delete corresponding password: Touch screen for lights on & long
press 4 for 2 seconds at this time input password code and press # to
confirm.
3.5. Delete all password: Touch screen for lights on & long press 4 for
2 seconds press # to delete all passwords.
Product Features:
● Multiple way to access: Fingerprint, Pin Code, RFID Card, & Mechanical Key.
● Fingerprint: Advanced semiconductor sensors with 360° scanner.
● Pin code Elegant keypad with code scrambling feature. Before correct password
can input 12 digital which can avoid password peeping.
● Dual authentication mode: Fingerprint mode ( master + common user ),
fingerprint + pin code, fingerprint + RFID card mode, After this setting dual
authentication will be required to access the lock at same time to open the door,
suitable for special occasions.
● Lock can have multiple access users capacity: Fingerprint ( 5 Master Users &
85 Normal Users ), Pin-code ( 5 Master Users & 15 Normal Users ), RFID cards
(99 Normal Users)
● Alarm: Tamper, low battery alarm and password protection.
● External power supply: Can use power bank with 5V for emergency power supply.
1. All fingerprint need to scan 3 times for addition.
2. Password is of 8 digit and has to be entered 2 times for addition.
3. Card is registered after voice prompts "add user" & scan card near RFID
scanner for confirmation.
4. After successful registration press * to exit.
Remark:
1. After installation of lock please reset lock to factory default mode.
2. After factory default mode make sure to register 1 master user.
3. The handle is the key part for opening and closing door, and its flexibility
ratio directly influences the usage of door lock, hence, don't hang articles on
handle.
4. Gently press fingerprint on the fingerprint sensor for registration of finger-
print. Please don't press with great force to prevent scratching the fingerprint
sensor.
5. This lock uses 4 AA high-energy alkaline batteries (1.5V). When it prompts"
the voltage is low, please replace battery" for the first time, the door can be
opened for about 100 times as per different battery capacities; At this time,
the battery should be replaced promptly to avoid inconvenience due to
the exhausted battery.
Remark:
4. Checking lock information:
Touch screen for lights on 2 long press 0 for 2 seconds:
Press 1 To open with any registered user.
Press 2 For dual authentication with fingerprint.
Press 3 For fingerprint + password opening.
Press 4 For fingerprint + card opening.
Press 5 To get the lock storage status: Number of master users, number of
normal users, for fingerprint, RFID & Pin code access.
Press 6 To get the lock series information: XXXXXXXX
Press 7 For rest factory default and # to confirm.
1. When Deleting fingerprint, one master user in fingerprint has to be left.
Remark:
#24, Shambavi Building, 23rd Main, Marenahalli, JP Nagar 2nd Phase, Bengaluru - 560078
Phone : 91-8026090500 | Email : sales@esslsecurity.com
www.esslsecurity.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

eSSL FL-300 User manual

Type
User manual

eSSL FL-300 is an intelligent fingerprint door lock that offers multiple ways to access: fingerprint, pin code, RFID card, & mechanical key. With advanced semiconductor sensors and a 360° scanner, it provides accurate and secure fingerprint recognition. It supports multiple users, including 5 master users and 85 normal users for fingerprint access, 5 master users and 15 normal users for pin code access, and 99 normal users for RFID card access. This lock also features dual authentication mode for added security, where two different methods are required to open the door.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers