Parrot Uncle F6297 1 User manual

Brand: Parrot Uncle

Model: F6297 1

Category: Household fans

Type: User manual

Parrot Uncle F6297 1 is a ceiling fan with a remote control that separately controls fan speed and light. It has four fan speed settings (high, medium, low, and off) and a light button to turn the light on and off. The fan has a reversible motor for use in both summer and winter, and it comes with a balancing kit to ensure smooth operation. The remote control also features a timer function with 2, 4, and 8-hour settings.

CEILING FAN

F6233Q110V

Installation & Operating Instructions for the

Parrotuncle Owner's Installation ,Manual

WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER

Installation & Operating Instructions for the

Parrotuncle Owner's Installation ,Manual

WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER

Thank you for purchasing this quality product. To ensure correct function and safety, please read and save all

instructions before using the product

To avoid possible electric shock, tur he electricity at the main fuse box or circuit panel before you begin the fan installation or

before servicing the fan o .

Read all instructions and safety information carefully before installing your fan and save these instructions.

Make sure all electrical connections comply with local codes or ordinances and the National Electrical Code. If you are unfamiliar with

electric wiring, please use a qualiﬁed and licensed electrician.

Make sure you have a location selected for your fan that allow clear space for the blades to rotate, and at least seven (7) feet of clearance between the ﬂoor and

the fan blade tips. The fan should be mounted at least thirty (30) inches from walls or other upright structures.

WARNING: The outlet box and ceiling support joist used must be securely mounted, and capable of supporting at least 100 pounds. To

reduce the risk of ﬁre, electric shock or personal injury, mount to the outlet box marked acceptable for fan supported and use mounting

screws provided with the outlet box. The box must be supported directly by the building structure.

WARNING: To reduce the risk of ﬁre, electric shock or personal injury, mount to outlet box marked “acceptable for fan support” and use mounting

screws provided with the outlet box most outlet boxes commonly used for the support of lighting ﬁxtures are not acceptable for fan

support and may need to be replaced. Consult a qualiﬁed electrician if in doubt.

Electrical diagrams are for reference only. Light kits that are not packed with the fan must UL listed and marked suitable for use with the

model fan you are installing. Switches must be UL. general use switches. Refer to the instructions packaged with the light kits and

switches for proper assembly.

After installation is complete, check that all connections are absolutely secure.

After making electrical connections, spliced conductors should be turned upward and pushed carefully up into outlet box. The wires

should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet box.

WARNING: To reduce the risk of electrical shock and ﬁre, do not use this fan with any solid-state fan speed control device, or rheostat.

Do not separate the reverse switch until the fan has come to a complete stop.

Do not insert anything into the fan blades while they are rotating.

WARNING: To reduce the risk of personal injury, do not bend the blade brackets (also referred to as “ﬂanges”) during assembly or after

installation. Do not insert objects in the path of the blades.

To avoid personal injury or damage to the fan and other items, be cautious when working around or cleaning the fan.

Do not use water or detergent when cleaning the fan or fan blades. A dry dust cloth or lightly dampened cloth will be suitable for most cleaning.

10.

11.

12.

13.

14.

15.

NOTE: The important safety precautions and instructions appearing in the manual are not meant to cover all possible conditions and situations that may

occur. It must be understood that common sense and caution are necessary factors in the installation and operation of this fan.

NOTE: This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities are

di erent or are impaired, or lack of experience or knowledge, unless such persons are supervised or trained to operate the appliance

by a person responsible for their safety.

NOTE: Children should be supervised to ensure that they do not use appliances as a toy.

THANK YOU FOR YOUR PURCHASE

SAFETY TIP

F6233Q110V

accessoriesinstallingr

Pls check whether above accessories are completed or not?Yes,and install.

Installation & Operating Instructions for the

Parrotuncle Owner's Installation ,Manual

WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER

1 2

2H4H 8H

Mounting screws(2PCS)

Washer(2PCS) Remote control (1 PC)

Mounting bracket

Fan motor assembly

Canopy

Blade 5PCS

F6233Q110V

Plastic wire nut (6PCS)

Balancing sticker (2PCS)

Balancing clip (1PC)

Blade screw (16PCS)

Washer (16PCS)

Bulb(excluded)

Installation & Operating Instructions for the

Parrot uncle Owner's Installation ,Manual

WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER

outlet

X10

F6233Q110V

Installation & Operating Instructions for the

Parrotuncle Owner's Installation ,Manual

WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER

FROM POWER SOURCE

AC 110- 120 VOLT 60Hz

3.5AMPS.

R E C E I V E R

OUTPUT

Ground wire

White

Black

Red

White

Blue

supplied with the

remote controller

Use plastic wire nuts

supplied with the

Use plastic wire nuts

fans

MOTOR

F6233Q110V

Installation & Operating Instructions for the

Parrotuncle Owner's Installation ,Manual

WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER

F6233Q110V

X15

X10

(WINTER TIME)

(SUMMER TIME)

A.warm weather-(Forward) A Downward airﬂow creates a cooling e .

This allows you to set your air conditioner on a higher setting without

ag your comfort.

B.Cool weather-(Reverse) An upward airﬂow moves warm air o

ceiling.This allows Reverse you to set heating unit on a lower setting

without a g your comfort.

Installation & Operating Instructions for the

Parrotuncle Owner's Installation ,Manual

WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER

ffect

ffectin

ff the

ffectin

The remote controller

controls the fan as follows:

3 key - for fan high spead

2 key - for fan medium spead

1 key - for fan low spead

OFF key - for fan off

LIGHT key - for light on and off (color selection)

2hr,4hr,8hr botton to set the FAN sleep timmer

controls

F6233Q110V

X3 X2

Installation & Operating Instructions for the

Parrotuncle Owner's Installation ,Manual

WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER

size of product

F6233Q110V

12"

11"

103

48"

CONNECT TO

Green fan wire ....Bare supply wire

Red or Black receiver wire(ACIN L)....Red or Black supply wire

White receiver wire(AC IN N)....White supply wire

White receiver wire(TO MOTOR N)....White fan wire

Black receiver wire(TO MOTOR L)....Black fan wire

Blue receiver wire(FOR LIGHT) ....Blue light wire

CAUTION: Ceiling Angle Shall Not Exceed 30 Degrees,

For Mounting Controller,Model RE-022

WHITE

BLACK

ANT

INPUT

OUTPUT

WHITE

BLUE

BLACK

RED or BLACK

RECEIVER

CANOPY

RECEIVER

(FIG.4)

WIRE NUT

Use wire connecting nuts

supplied with the remote

controller.

(FIG.3)

Use wire connecting nuts supplied with the fan

FROM POWER SOURCE

AC 110- 120 VOLT 60Hz

3.5AMPS.

ANTENNA PUT AT OUTSIDE

OF CANOPY BOX CAN GET

MORE OPERATION

DISTANCE

FAN MUST BE KEPT AT THE HIGH SPEED

LIGHT MUST BE KEPT AT THE ON P0SITION

Remote controller

GENERAL INFORMATION

INSTRUCTION OF INSTALLATIONAND OPERATION

1.SETTING THE CODES

To set the codes, perform the following steps:

A.Setting the codes on the transmitter:

a.Remove battery cover.Press firmly on the arrow and slide battery cover off.

b.Slide code switches to your choice of up or down position.(Factory setting is all up. Do not use this position.Use a

Small screwdriver or ball point pen to slide firmly up or down (Figure 1)).

B.Setting the codes on the receiver:

The Learn Key must be pressed with in 30 seconds, after pressing the Power button.

If not, please press the Power button to restart.

Keep pressing the button learn key in excess of 3 second it becomes a LEARN status.

The receiver can remember the last codes status. The light flash two times.

2.INSTALLING RECEIVER IN CEILING FAN

A.Safety precautions:

WARNING: HIGH VOLTAGE! Disconnect power by

removing fuse or switching off circuit breaker.

Do not use with solid state fans.

Electrical wire must meet all local and national

electrical code requirements.

Supply for fan must be 110/120 volt, 60Hz. Maximum

fan motor amps: 1.0,Maximum light watts: 180

incandescent or ballast and LED.

Otherwise power can cause serious injury or death.

B.lnstalling receiver in fan:

a.Remove power from the circuit.

b.Remove ceiling fan canopy from the mounting

bracket.

c.Disconnect existing wiring between ceiling fan and

Supply in electrical junction box.

d. Make connections as follows, using the wire nuts

supplied:

This remote controller is desianed to separately control your ceiling fan speed and light on and off.

There are four buttons(HI,MED, LoW,OFF) to control the speed of the fan and off.

The light button will control the light on and off.

The red indicator on the transmitter will light when one of the five buttons is pressed.

Installation & Operating Instructions for the

Parrotuncle Owner's Installation ,Manual

WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER

F6233Q110V

YOUR REMOTE NOW HAS FULL CONTROL OF THE FAN AND LIGHT .

OPERATION DISTANCE 20 FEET

MODEL:

RE-011

TRANSMITTER

Optional Wall Mounting for Transmitter Holder

Place in accessible area of your home, and screw the

transmitter holder into wall using the two screws

provided,slide hand unit into holder.

4.TROUBLE SHOOTING GUIDE1.Fails to operate

a. Power to receiver ?

b.Receiver wired correctly ?

c.Fan manual speed control in highest position ?d.Light kit switch turned on ?

e.Good battery in the transmitter ?

f. Code set at exact same positions in both transmitter and receiver ?

2.Won' t operate at distance

MAX. Motor amps: 1.0

MAX.Light watts: 180-(incandescent, or ballast non-dimmer, or LED)

If transmitter operates fan/light kit when up close,but not at 20 feet away.

Try placing the brown antenna wire higher,up through ceiling/outside the junction box.

NOTICE!

Your ceiling fan and light kit assembly must meet the following requirements:

1.Do not use with solid state fans.

2.Electrical rating: 120v 60Hz 3.5A

WARNING

TO REDUCE THE RISK OF SHOCK, THIS FAN MUST BE INSTALLED WITHAWALL CONTROL/SWITCH.

FCC Statement:

1. This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2)This device must accept any interference received, including interference that may cause undesired operation.

2.Changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user's

authority to operate the equipment.

NOTE:This equipment has been tested and found to comply with the limits for a Class B digital, pursuant to Part 15 or

the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential

installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may casue harmful interference to radio communications,

However, there is no guarantee that interference will not occur in a particular installation.If the equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following measures:

--- Reorient or relocate the receiving antenna.

--- Increase the separation between the equipment and receiver.

--- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

--- Consult the dealer or an experienced radio/ TV technician for help.

If other fans or supply wires are different color, have this unit installed by qualiﬁed licensed electrician.

e.Push all connected wires up into junction box.

f. Lay the brown antenna wire on top of the receiver, and put the receiver into the mounting bracket.

g.Reinstall the canopy on the mounting bracket.

h.Restore power.

3.OPERATINGTRANSMITTER:

A. lnstall1.5 volt battery(not included).(To prevent damage to transmitter, remove the battery if not used for along time).

B.Store the transmitter away from excessive heat or humidity.

C.This remote control unit is equipped with roll code combinations. In order to prevent possible interference from or to

other remote units such as garage door openers, car alarm or security system. If you ﬁnd that your fan and light kit go

on and off without using your remote control, simply change the code combination in your transmitter and receiver.

D. Operating the buttons on the panel of the transmitter.

3 key -for fan high speed.

2 key-for fan medium speed.1 key-for fan low speed.

OFF key-for fan off.

LIGHT key-for light on and off.

2hr , 4hr , 8hr button to set the FAN sleep timer

Installation & Operating Instructions for the

Parrotuncle Owner's Installation ,Manual

WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER

F6233Q110V

WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER

Table of Contents

Fan

/ Remote is not working

Fan is noisy

Fan Wobbles

Light is not working

Please refer to the instruction sheet for detailed directions and descriptions of

installation steps

and requirements.

FAN

/ REMOTE IS NOT WORKING

Ensure the remote is within the 20

foot range of the receiver

To reset the remote control: 1) Turn oﬀ power to fan

using the wall switch or circuit breaker. 2) Remove ba eries from remote.

3) Wait 10 seconds. 4) Replace ba eries and turn power on

Check ba eries to

insure they are good and oriented correctly

Check to make sure the frequency switches (DIP Switches) from the remote to the receiver are set to the same frequency

Check the main

and branch circuit fuses or breakers

If using a Variable Speed Wall Switch, ensure

it is speciﬁcally designed for use with a ceiling fan.

Check the line wire connec ns to the fan and the

switch wire conn e switch housing

per the instru ns

Support@parrotuncle.com

THE FAN IS NOISY

Make sure all motor housing screws are tened

Make sure the screws that a an blade to motor ar t

Make sure the wire nut connectors are not ra against each other or the interior wall of the switch housing

Allow 24-hour break in period. Most noises associated with the new fan may disappear during th me

If using a ceiling light kit, make sure the glassware is secur htly

Make sure there is a short distance/gap from the ceiling to the top of the canopy. The canopy

should not touch the ceiling!

Make sure your ceiling box is secure and that the rubber isolator pads are used between the moun acket and outlet box

TROUBLESHOOTING GUIDE

F6233Q110V

Installation & Operating Instructions for the

Parrotuncle Owner's Installation ,Manual

WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER

3. THE FAN WOBBLES

Verify all blades and blade bracket screws are secure (most fan wobble problems are caused by loose parts). Once fan is properly

installed, run the ceiling fan for 10 minutes to let the fan self-adjust.

If wobble occurs a er running the fan for 10 minutes, verify blade level using the following process:

select a point on the ceiling above the p of one of the blades. Then select the fan blade and measure from the center

of the selected blade to point on the ceiling. Rotate the fan un e next blade is oned and repeat the

measurement using the same point from the ceiling for every blade. Measurements

should be within 1/8 inch.

Customer Service Support@parr

otuncle.com to order a complimentary Blade Balancing Kit

Customer Service Support@parrotuncle

.com to order a complimentary Blade Balancing Kit

LIGHT IS NOT WORKING

Check Bulb to make sure it is installed correctly

Remove non-working bulb and replace with a bulb that is known to be a good working bulb

To reset the remote control: 1) Turn oﬀ power to fan

using the wall switch or circuit breaker. 2) Remove ba eries from

remote. 3) Wait 10 seconds. 4) Replace ba and turn power on

F6233Q110V

AFTER INSTALLATION

The fan blades have been adjusted in the factory to minimize any wobble

NOTE:CEILING FANS TEND TO MOVE DURING OPERATION DUE TO THE FACT THAT THEY

ARE MOUNTED ON A RUBBER CROMMET. IF THE FAN WAS MOUNTED RIGIDLY TO THE

CEILING, IT WOULD CAUSE EXCESS VIBRATION. MOVEMENT OF A FEW CENTIMENTERS

IS QUITE ACCEPTABLE AND DOES NOT SUGGEST ANY PROBLEM

WOBBLE”

TO REDUCE THE FAN WOBBLE: PLEASE CHECK THAT ALL SCREWS WHICH SECURED THE MOUNTING

BRACKET AND DOWNROD ARE SECURE.

BALANCING A WOBBLING CEILING FAN:

For your convenience, a Balancing Kit is included; please follow this procedure when balancing the fan:

1.Check that all blade and blade arm screws are secure.

2.Most fan wobbling problems are caused when blade levels are unequal. Check this level by

selecting a point on the ceiling above the tip of one of the

blades. Measure this distance.Rotate the fan until the next blade is positioned for

measurement. Repeat for each blade. The distance deviation should be equal within

1/8"(0.32cm).

3.Use the enclosed Blade Balancing Kit if the blade

wobble is still noticeable.

4.If the blade wobble is still noticeable, interchanging two

adjacent (side by side) blades can redistribute the weight and possibly result in smoother

operation. WARNING: TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE

BLADE ARM WHILE INSTALLING, BALANCING THE BLADES, OR CLEANING THE FAN. DO

NOT INSERT FOREIGN OBJECTS BETWEEN ROTATING FAN BLADES.

NOISE

When it is quiet(especially at night) you may hear occasional small noises. This is normal. Please allow

a 24-hour “breaking-in” period, most noises associated with a new fan disappear during the time.

CARE AND CLEANING

1.Periodic cleaning of your ceiling fan is the only maintenance required. Use a soft brush or lint free cloth to

avoid scratching the paint ﬁnish. Please make sure to turn off electricity power before you clean your fan

2.Do not use water when cleaning your ceiling fan. It could damage the motor or the blades

and create the possibility of an electrical shock.

3.Motor has permanently lubricated ball bearing. No need to oil

NOTE: MAKE SURE THE POWER IS OFF AT THE ELECTRICAL PANEL BOX BEFORE YOU

ATTEMPT ANY CLEANING OR REPAIRS.

Installation & Operating Instructions for the

Parrotuncle Owner's Installation ,Manual

WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER

F6233Q110V

Parrot Uncle F6297 1 User manual

Brand: Parrot Uncle

Model: F6297 1

Category: Household fans

Type: User manual

Download PDF

report

Parrot Uncle F6297 1 User manual

Parrot Uncle F6297 1 User manual

Related papers

Other documents