B&G NSS9 evo3 Template

Brand
B&G
Model
NSS9 evo3
Type
Template

This manual is also suitable for

Mounting Template
9″ Units
NSS evo3/NSS evo3S
Zeus³/Zeus³S
NOTE:
DO NOT SCALE
PRINT 1:1
IMPORTANT. Do not use this template if it has been rescaled by copying or

dimension lines below are to scale before use.







escala antes de usar.






















注意：请尽量不要使用本安装挖孔尺寸模版图的复印件。如果使用复
印件，则在使用之前请确认其比例一定要与原件大小必须一致。
중요: 복사나 출력으로 크기가 조정 된 경우 이 템플릿을 사용하지
마십시오. 원본이 아니거나 인쇄물이면, 사용하기 전 아래 치수선의
눈금을 확인 해 주십시오.
注：このテンプレ トは印刷やコピ によって縮尺がわっている
ことがありますので使用しないで下さい。テンプレ トがオリジナ
ルのものでない場合には、下の寸法線を使って縮尺を確認してくだ
さい。
ВНИМАНИЕ: Не используйте эту инструкцию, если она б
ыла изменена в размерах при копировании или распечат
ке. Если вы используете не оригинал, а распечатку из фа
йла, убедитесь в соответствии размеров линейки в нижн
ей части инструкции с действительными размерами.
Check dimensions before cutting
12"
300 mm
*988-11398-003*
Front mount screw recommendations
Max 5.5 mm (0.22”)
Max
2.2 mm
(0.09”)
Ø12.5 mm (1/2”)
146.0 mm (5.75”)
SUN COVER
PRODUCT OUTLINE
171.2 mm (6.74”)
166.3 mm (6.55”)
112.1 mm ( 4.41”)
270.1 mm (10.63”)
292.0 mm (11.49”)
143.5 mm (5.64”)
135.0 mm (5.31”)
146.0 mm (5.75”)
143.5 mm (5.64”)
135.0 mm (5.31”)
147.7 mm (5.81”)
73.8 mm (2.90”)
83.2 mm (3.27”)
85.6 mm (3.37”)
73.8 mm (2.90”)
83.2 mm (3.27”)
85.6 mm (3.37”)
129.0 mm (5.07”)
67.0 mm (2.63”)67.0 mm (2.63”)
67.0 mm (2.63”)67.0 mm (2.63”)
129.0 mm (5.07”)
129.0 mm (5.07”)
129.0 mm (5.07”)
Material
Soft materials e.g. Plywood
Hard material e.g. Fiberglass, Acrylic, Hardwoods
Recommended pilot holes
#4 screw
Ø 1.9-2.2 mm (5/64”)
Ø 2.3-2.6 mm (3/32”)
#6 screw
Ø 2.3-2.5 mm (3/32”)
Ø
2.7-3.1 mm (7/64”)
Remove shaded area
287.0 mm (11.30”)
L
C
L
C
  • Page 1 1

B&G NSS9 evo3 Template

Brand
B&G
Model
NSS9 evo3
Type
Template
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents