ADDER CCS-LED Owner's manual

Category
Network switches
Type
Owner's manual

This manual is also suitable for

www.adder.com
CCS-XB
CCS-XB
Quick Start
Safety information
• Foruseindry,oilfreeindoorenvironmentsonly.
• Notsuitableforuseinhazardousorexplosive
environmentsornexttohighlyammable
materials.
• Ensurethatalltwistedpairinterconnectcables
areinstalledincompliancewithallapplicable
wiringregulations.
• DonotconnecttheCATxcable(s)(RJ45
styleconnector(s))toanyotherequipment,
particularlynetworkortelecommunications
equipment.
• Wherepossible,avoidlayingthetwistedpair
linkcable(s)alongsidepowercables.
• Donotattempttoservicethemodulesyourself.
Warranty
AdderTechnologyLtdwarrantsthatthisproductshallbefreefromdefectsinworkmanshipandmaterials
foraperiodoftwoyearsfromthedateoforiginalpurchase.Iftheproductshouldfailtooperatecorrectly
innormaluseduringthewarrantyperiod,Adderwillreplaceorrepairitfreeofcharge.Noliabilitycan
beacceptedfordamageduetomisuseorcircumstancesoutsideAdder’scontrol.AlsoAdderwillnotbe
responsibleforanyloss,damageorinjuryarisingdirectlyorindirectlyfromtheuseofthisproduct.Adder’s
totalliabilityunderthetermsofthiswarrantyshallinallcircumstancesbelimitedtothereplacementvalue
ofthisproduct.Ifanydifcultyisexperiencedintheinstallationoruseofthisproductthatyouareunableto
resolve,pleasecontactyoursupplier.
Self adhesive
rubber feet
CCS-XB controller
Four LED monitor indicators
AdderP/N:CCS-LED
(Alsoavailableseparatelywhen
morethanfourarerequired)
CATx link cable
Adder P/N: VSC46
Whats in the box
Connection overview inside
Fulluserguideavailableatwww.adder.com
©2014AdderTechnologyLimited•Alltrademarksareacknowledged.
PartNo.MAN-CCS-XB-QS•Release1.1f(tober2.0aonrelease)
Web: www.adder.com
Contact: www.adder.com/contact-details
Support: forum.adder.com
TheCCS-XBmoduleworkstogetherwitheithertheAdderCCS4-USBorCCS-PRO4switchestoprovideLED
indicatorsforeachofyourvideodisplayscreens.Astheswitchactivatesascreen,theCCS-XBmoduleactivates
thecorrespondingindicator(whichcanbeattachedtothescreen)toprovideextraclarityfortheoperator.
Checking the firmware version (CCS4-USB switches only)
WhenusingtheCCS-XBmodulewithaCCS4-USBswitch,itisimportantthattheswitchhasrmwareversion
2.0(orgreater)installed.IfindoubtyoucancheckthermwareversionofyourCCS4-USBswitchasfollows:
1 WithyourCCS4-USBswitchpoweredonandwithaUSBkeyboardattached,pressandholdthe
COMPUTERbuttonforroughlysixsecondsuntilthedisplayshowsC.
2 Ontheconnectedkeyboard,pressFfollowedby1 andthenpressEnter.Thedigitsofthermware
versionwillbeshowninsequencewithashortpausebetweeneach.Forinstance,1 > 0 > 2meansthat
thermwareversionis1.02andrequiresanupgrade.
3 PressEandthenpressEntertoreturntheCCS4-USBtonormaloperation.
IfyourCCS4-USBswitchdoesrequirearmwareupgrade,pleaserefertothePerforming upgrades
sectionoftheCCS4-USBuserguide.
C
Connection
overview
Steps to a successful installation
1 UsethesuppliedVSC46CATxlinkcable(A)toconnecttheCCS-XBunittotheOPTIONSportofyourCCS4-USBorCCS-PRO4switch.
2 Thenextstepdependsonyourswitchtype:
• CCS-PRO4-Useastandardpatchcable(B)toconnectthenetworkportofyourCCS-PRO4tothenetworkportofyourcomputer(eitherdirectlyor
viaanetworkswitch-furtherinformationavailableintheCCS-PRO4userguide),or
• CCS4-USB-UsetheVSC40ashupgradecable(C)(suppliedwithyourswitch)toconnecttheCCS-XBmoduletotheserialportofyourcomputer.
3 ConnectthesuppliedLEDmonitorindicators(D)totherstfourLEDoutputportsontheCCS-XBmodule.
4 Ifyourswitchisnotalreadypoweredon,applypowertoitnow.CCS4-USBswitchesneedtobere-poweredwheneveraCCS-XBunitisre-attached;
thispromptsthemtolocatetheCCS-XBunit.CCS-PRO4switchescansenseanewlyattachedCCS-XBunitwithouttheneedforre-powering.
5 DownloadandruntheFree-FlowcongurationapplicationfromtheAdderwebsite(www.adder.com)andfollowtheinstructionsgiveninthelatest
versionofyourCCS4-USBorCCS-PRO4userguide(alsoavailablefromtheAdderwebsite).Thesection‘ConguringLEDmonitorindicators’will
showyouhowtoassignanindicatortoeachdisplay.
Note: Once the LED monitor indicators have been programmed, you can remove the VSC40 flash cable or network patch cable connections as these
are not required for operation. You will need to reconnect them, however, if you alter the LED assignments.
OPTIONS port
(CCS4-USB
and CCS-PRO4
switches)
Connect to a
vacant serial
port on your
computer
(CCS4-USB
switches only)
LED monitor indicators
(one per video display)
CATx link cable
Adder P/N: VSC46
(Included in CCS-XB kit)
Flash upgrade cable
Adder P/N: VSC40
(Included in CCS4-USB kit)
A
D
B
Network port
(CCS-PRO4
switches only)
To a network
switch or your
computer’s
network port
  • Page 1 1
  • Page 2 2

ADDER CCS-LED Owner's manual

Category
Network switches
Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI