Page is loading ...
2
G Operating instruction
Thank you for choosing a Hama product.
Take your time and read the following instructions
and information completely. Please keep these
instructions in a safe place for future reference. If
you sell the device, please pass these operating
instructions on to the new owner.
Controls and Displays
A) Remote control
1. Dimmer function (lighter in 6 increments) /
increase program speed
2. Constant red colour
3. Constant yellow-orange colour
4. Constant sunlight-yellow colour
5. Constant yellow colour
6. Constant yellow-green colour
7. Dimmer function (darker in 6 increments) /
decrease program speed
8. Constant green colour
9. Constant turquoise colour
10. Constant light blue colour
11. Constant sky-blue colour
12. Constant pale blue colour
13. OFF-Taste (Switch off)
14. Constant dark blue colour
15. Constant blue colour
16. Constant purple colour
17. Constant rose colour
18. Constant pink colour
19. ON button (Switch on)
20. Constant while colour
21. “Flash” program, colour changes in pulsating
pattern (7 colours)
22. “Strobe” program, brightness of white tone
changes (from light to dark)
23. “Fade” program, gradual colour transitions
(7 colours)
24. “Smooth” program, colour changes in pulsating
pattern (3 colours)+
B) LED band with control unit
25. USB cable
1. Explanation of Warning Symbols and Notes
Warning
This symbol is used to indicate safety
instructions or to draw your attention to
specific hazards and risks.
Note
This symbol is used to indicate additional
information or important notes.
2. Package Contents
•L
ED strip (2x 50 cm) with contr
ol unit
•USB cable
•Remote control
•1x battery type: CR2025
•These operating instructions
Note
Please check that the set is complete before
using it and ensure that none of the parts is
faulty or damaged.
3. Safety Notes
•Protect the product from dirt, moisture and
overheating, and only use it in a dry environment.
•The product is intended for private, non-
commercial use only.
•Use the product for its intended purpose only.
•Do not use the LED band while it is still in the
packaging or when it is rolled up.
•Do not operate the product outside the power
limits given in the specications.
•Always pull directly on the plug when
disconnecting the cable, never on the cable
itself.
•Lay all cables so that they do not pose a tripping
hazard.
•Do not bend or crush the cable.
•Do not drop the product and do not expose it to
any major shocks.
3
•Be careful not to bend the LED band. This can
cause damage to the band.
•Do not connect the product to other lighting
systems.
•Do not open the device or continue to operate it
if it becomes damaged.
•Do not attempt to service or repair the product
yourself. Leave any and all service work to
qualied experts.
•Keep this product, as all electrical products, out
of the reach of children!
•Dispose of packaging material immediately
according to locally applicable regulations.
•Do not modify the product in any way. Doing so
voids the warranty.
Warning – Batteries
•Immediately remove and dispose of dead
batteries from the product.
•Only use batteries (or rechargeable batteries)
that match the specied type.
•When inserting batteries, note the correct
polarity (+ and - markings) and insert the
batteries accordingly. Failure to do so could
result in the batteries leaking or exploding.
•Do not charge batteries.
•Do not throw batteries in a re.
•Keep batteries out of the reach of children.
•Never open, damage or swallow batteries or
allow them to enter the environment. They
can contain toxic, environmentally unfriendly
heavy metals.
•Remove the batteries from the product if you
will not be using it for an extended period,
unless it is being kept ready for emergencies.
4. Operation
•Connect the USB cable (25) to the control unit of
the LED band.
•Then connect the USB connector on the USB
cable (25) to the USB port on your television.
•Alternatively, you can also connect the USB
connector to a USB charger or to another
terminal device with USB port.
Note - Connecting to terminal devices
•Before connecting to a terminal device, check
whether the power output of your terminal
device can supply sucient power for the
LED band.
•For more information, please refer to the
operating instructions of your terminal device.
If necessary, ask the relevant manufacturer’s
support centre for the information you need.
•Remove the protection foil from the rear of the
LED band to fasten it to your television, wall, etc.
using the self-adhesive strip on the rear.
Note
•Ensure that you do not cover any
connections, ventilation holes or similar when
attaching the product.
•Remove the contact breaker between the battery
and the contacts before operating the remote
control.
•Press the ON button (19)/OFF button (13) on the
remote control to switch the LED band on/off.
Note
•Ensure that there are no objects that could
block or interfere with the signal between the
IR sensor and the control device.
•To replace the battery of the remote control,
open the battery compartment on the back of
the remote control and replace the battery with a
new one of type CR2025. Ensure that the polarity
is correct.
4
5. Installation
Error Solution
LED does not
light up
Check that the LED is switched on;
if necessary switch it on using the
remote control.
Check the connections.
Check to make sure that the termi-
nal device is connected to the LED
band and that it is switched on.
Remote
control does
not respond
Check that there are no obstacles
between the remote control and
the IR sensor of the control unit;
remove these if necessary.
Check whether the battery in the
remote control is dead; if necessa-
ry, replace it with a new battery.
6. Care and Maintenance
•Use only a dry cloth to clean the device.
•Do not use any aggressive cleaners.
•The LEDs cannot be replaced.
7. Warranty Disclaimer
Hama GmbH & Co. KG assumes no liability and
provides no warranty for damage resulting from
improper installation/mounting, improper use of
the product or from failure to observe the operating
instructions and/or safety notes.
8. Service and Support
Please contact Hama Product Consulting if you
have any questions about this product.
Hotline: +49 9091 502-115 (German/English)
Further support information can be found here:
www.hama.com
9. Technical Data
LED band with
control unit
Remote control
Operating
voltage
5 V3V
Power
consumption
460 mA -
Output 2.5 W-
Specications/
battery type
USB 2.0 (USB
cable/connector)
1x CR2025
Length
50 cm
(USB cable) 2x
50 cm
(LED band)
-
10. Recycling Information
Note on environmental protection:
After the implementation of the European
Directive 2012/19/EU and 2006/66/EU in
the national legal system, the following
applies: Electric and electronic devices as
well as batteries must not be disposed of
with household waste. Consumers are obliged by
law to return electrical and electronic devices as
well as batteries at the end of their service lives to
the public collecting points set up for this purpose
or point of sale. Details to this are dened by the
national law of the respective country. This symbol
on the product, the instruction manual or the
package indicates that a product is subject to these
regulations. By recycling, reusing the materials or
other forms of utilising old devices/Batteries, you
are making an important contribution to protecting
our environment.
00096016/07.16
All listed brands are trademarks of the corresponding companies. Errors and omissions excepted,
and subject to technical changes. Our general terms of delivery and payment are applied.
Hama GmbH & Co KG
86652 Monheim
/Germany
www.hama.com
/