2. Computers & electronics
  3. TVs & monitors
  4. Plasma TVs
  5. LG
  6. 50PT350R
50PT350R

LG 50PT350R, 42PT350R, 50PV250R Owner's manual

  • Hello! I am an AI chatbot trained to assist you with the LG 50PT350R Owner's manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
www.lg.com
OWNER’S MANUAL
PLASMA TV
Please read this manual carefully before operating
your set and retain it for future reference.
HDMI, the HDMI logo and High-Denition Multimedia Interface
are trademarks or registered trademarks of HDMI Licensing LLC.
10 mm (+/-5 mm)
The items supplied with your product may vary depending on the model.
Product specications or contents of this manual may be changed without prior notice due to upgrade of
product functions.
■ How to use the ferrite core
1 Use the ferrite core to reduce the electromagnetic interference in the PC audio cable.
Wind the PC audio cable on the ferrite core thrice. Place the ferrite core close to the TV.
2 Use the ferrite core to reduce the electromagnetic interference in the power cable.
Wind the power cable on the ferrite core once. Place the ferrite core close to the TV.
3 Use the ferrite core to reduce the electromagnetic interference in the power cable.
Wind the power cable on the ferrite core once. Place the ferrite core close to the TV and a wall plug.
- If there is one ferrite core, follow as shown in Figure 1.
- If there are two ferrite cores, follow as shown in Figures 1 and 2.
- If there are three ferrite cores, follow as shown in Figures 1 and 3.
[to an External device]
[to the TV]
[to the TV]
[to the TV]
[to a wall plug]
[to a wall plug]
[Cross Section of
Ferrite Core]
[Cross Section of
Ferrite Core]
[Cross Section of
Ferrite Core]
CONTENTS
PREPARATION

EXTERNAL EQUIPMENT SETUP











WATCHING TV / PROGRAMME CONTROL

















TO USE A USB DEVICE






PICTURE CONTROL











SOUND & LANGUAGE CONTROL













II

CONTENTS
II

Clock Setup .......................................................72
Auto on/off time setting .....................................73
Sleep Timer setting ...........................................73

Switch on/off .....................................................74
SIMPLE Text......................................................74
TOP Text............................................................74
FASTEXT ..........................................................75
Special Teletext Functions ................................75

Troubleshooting .................................................76
Maintenance ......................................................78
Product Specifications .....................................79
IR Codes ...........................................................81
External Control Device Setup ..........................82
A-1
PREPARATION

Ensure that the following accessories are included with your TV. If an accessory is missing, please
contact the dealer where you purchased the TV.
■ Image shown may differ from your TV.
Owner’s Manual
Batteries
(AAA)
Remote Control
Power Cord
Polishing Cloth
Polishing cloth for use on the screen.
This item is not included for all models.
* Lightly wipe any stains or fingerprints on
the surface of the TV with the polishing
cloth.
Do not use excessive force. This may
cause scratching or discolouration.

Cable Holder
Power Cord holder
Wall Mounting Bracket
(Separate purchase)
PSW400BG or PSW400B
or DSW400BG
Ferrite Core
(Depending on model)
Protection Cover
Protection cover
tape
x 3 x 4
Bolts for stand assembly
M5X14.5 M4X26
A-2

PREPARATION

!
?

► The energy consumed during use can be significantly reduced if the level of brightness of the picture is
reduced, and this will reduce the overall running cost.

► Do not step on the glass stand or subject it to any impact.
It may break, causing possible injury from fragments of glass, or the TV may fall.
► Do not drag the TV. The floor or the product may be damaged.
!
?
■ Image shown may differ from your TV.
42/50PT2***, 50PV2***, 42/50PT3***
P
HOMEINPUT OK
P
HOMEINPUT OK
P
HOMEINPUT OK
PROGRAMMEVOLUMEHOME OKINPUTPOWER

Adjusts picture according to the
surrounding conditions.


• Illuminates red in standby mode.
Touch Sensor
• You can use the desired
button function by
touching.
A-3
PREPARATION
P
HOMEINPUT OK
■ Image shown may differ from your TV.
42/50PT5***
P
HOMEINPUT OK
PROGRAMMEVOLUMEHOME OKINPUTPOWER
Touch Sensor
• You can use the desired
button function by
touching.
P
HOMEINPUT OK

Adjusts picture according to the
surrounding conditions.


• Illuminates red in standby mode.

A-4

PREPARATION
IN
RS-232C IN
(CONTROL&SERVICE)
ANTENNA
IN
COMPONENT IN
AV IN 1
AUDIO
VIDEO
L(MONO)
R
AUDIO
VIDEO
1
1
2
VARIABLE AUDIO OUT
AV IN2
IN 2

■ Image shown may differ from your TV.
42/50PT2***, 50PV2***
/DVI IN
RS-232C IN
(CONTROL&SERVICE)
ANTENNA
IN
COMPONENT IN
AV IN 1
AUDIO
VIDEO
L(MONO)
R
AUDIO
VIDEO
1
1
2
VARIABLE AUDIO OUT
AV IN2
IN 2
AUDIO IN
(RGB/DVI)
RGB IN
(PC)
IN
RS-232C IN
(CONTROL&SERVICE)
ANTENNA
IN
COMPONENT IN
AV IN 1
AUDIO
VIDEO
L(MONO)
R
AUDIO
VIDEO
1
1
2
VARIABLE AUDIO OUT
AV IN2
IN 2
1
3
8
6
2
7
4
10
9
2
6
5

This TV operates on an AC power. The voltage is
indicated on the Specifications page. Never
attempt to operate the TV on DC power.

Connect an HDMI signal to HDMI IN.
Or DVI(VIDEO)signal to HDMI/DVI port with DVI
to HDMI cable.

Connect the audio from a PC.

Connect the output from a PC.

Connect to the RS-232C port on a PC.
This port is used for Service or Hotel mode.

Connect audio/video output from an external
device to these jacks.

Connect an external amplifier or add a subwoofer
to your surround sound system.

Connect a component video/audio device to these
jacks.

Connect RF antenna to this jack.

Connect USB storage device to this jack.
1
2
3
4
5
6
7
8
9
10
A-5
PREPARATION
■ Image shown may differ from your TV.

This TV operates on an AC power. The voltage is
indicated on the Specifications page. Never
attempt to operate the TV on DC power.

Connect an HDMI signal to HDMI IN.
Or DVI(VIDEO)signal to HDMI/DVI port with DVI
to HDMI cable.

Connect the audio from a PC.

Connect the output from a PC.

Connect to the RS-232C port on a PC.
This port is used for Service or Hotel mode.

Connect audio/video output from an external
device to these jacks.

Connect an external amplifier or add a subwoofer
to your surround sound system.

Connect a component video/audio device to these
jacks.

Connect RF antenna to this jack.

Connect USB storage device to this jack.
1
2
3
4
5
6
7
8
9
10
IN
RS-232C IN
(CONTROL&SERVICE)
ANTENNA
IN
COMPONENT IN
AV IN 1
AUDIO
VIDEO
L(MONO)
R
AUDIO
VIDEO
1
1
2
VARIABLE AUDIO OUT
AV IN2
IN 2
1
42/50PT3***
IN
RS-232C IN
(CONTROL&SERVICE)
ANTENNA
IN
COMPONENT IN
AV IN 1
AUDIO
VIDEO
L(MONO)
R
AUDIO
VIDEO
1
2
2
VARIABLE AUDIO OUT
AV IN2
IN 3
AUDIO IN
(RGB/DVI)
RGB IN
(PC)
/DVI IN
1
3
8
2
7
4
9
6
5
IN
RS-232C IN
(CONTROL&SERVICE)
ANTENNA
IN
COMPONENT IN
AV IN 1
AUDIO
VIDEO
L(MONO)
R
AUDIO
VIDEO
1
2
2
VARIABLE AUDIO OUT
AV IN2
IN 3
AUDIO IN
(RGB/DVI)
RGB IN
(PC)
/DVI IN
1
6
10
2
IN
RS-232C IN
(CONTROL&SERVICE)
ANTENNA
IN
COMPONENT IN
AV IN 1
AUDIO
VIDEO
L(MONO)
R
AUDIO
VIDEO
1
1
2
VARIABLE AUDIO OUT
AV IN2
IN 2
IN
RS-232C IN
(CONTROL&SERVICE)
ANTENNA
IN
COMPONENT IN
AV IN 1
AUDIO
VIDEO
L(MONO)
R
AUDIO
VIDEO
1
2
2
VARIABLE AUDIO OUT
AV IN2
IN 3
AUDIO IN
(RGB/DVI)
RGB IN
(PC)
/DVI IN
1
6
10
2
1
IN
RS-232C IN
(CONTROL&SERVICE)
ANTENNA
IN
COMPONENT IN
AV IN 1
AUDIO
VIDEO
L(MONO)
R
AUDIO
VIDEO
1
2
2
VARIABLE AUDIO OUT
AV IN2
IN 3
AUDIO IN
(RGB/DVI)
RGB IN
(PC)
/DVI IN
1
3
8
2
7
4
9
6
5
42/50PT5***
A-6

PREPARATION

Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.
Assemble the parts of the  with the  of the TV.
Assemble the TV as shown.
Fix the 4 bolts securely using the holes in the back of the TV.
■ Image shown may differ from your TV.
■ When assembling the desk type stand, check whether the bolt is fully tightened. (If not tightened fully,
the product can tilt forward after the product installation.) If you tighten the bolt with excessive force, the
bolt can deviate from abrasion of the tightening part of the bolt.
1
2
3
M4X26
Stand Body
Stand Base
M5x14.5
Rear
Front
When assembling the stand, make sure
to distinguish and assemble the front and
rear side of the stand correctly.
A-7
PREPARATION

■ Image shown may differ from your TV.
Install the and . It will help prevent the power cable from being
removed by accident.
1
Gather and bind the cables with the .
2

► Do not move the TV by holding the Cable Holder & Power Cord Holder, as the Cable Holders may break,
and injuries and damage to the TV may occur.

A-8

PREPARATION
■ Image shown may differ from your TV.

Protection cover
1
Insert the  into the TV until clicking sound.
2
Attach the protection cover tape.
*
This will protect the opening from accumulating dust and dirt. When installing the wall mounting
bracket, use the Protection cover.

■ Image shown may differ from your TV.
■ This feature is not available for all models.
After installing the TV, you can adjust the TV set manually to the left or right direction by 20 degrees to
suit your viewing position.
A-9
PREPARATION

■ You should purchase necessary components to fix the TV safety and secure to the wall from the
market.
■ Position the TV close to the wall to avoid the possibility of it falling when pushed.
■ The instructions shown below are a safer way to set up the TV, by fixing it to the wall, avoiding the
possibility of it falling forwards if pulled. This will prevent the TV from falling forward and causing
injury. This will also prevent the TV from damage. Ensure that children do not climb or hang from
the TV.
Use the eye-bolts or TV brackets/bolts to fix the product to the wall as shown in the picture.
(If your TV has bolts in the eyebolts, loosen then bolts.)
* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.
Secure the wall brackets with the bolts on the wall. Match the height of the bracket that is mounted
on the wall.
Use a sturdy rope to tie the product for alignment. It is safer to tie the rope so it becomes horizontal between
the wall and the product.


1
2
3
!
?

► When moving the TV undo the cords first.
► Use a platform or cabinet strong and large enough to support the size and weight of the TV.
► To use the TV safely make sure that the height of the bracket on the wall and on the TV is the same.
A-10

PREPARATION

10 cm
10 cm
10 cm
10 cm
10 cm
Model
VESA
(A
*
B)
Standard
Screw
Quantity
42PT2*** 400
*
400 M6 4
50PT2*** 400
*
400 M6 4
50PV2*** 400
*
400 M6 4
42PT5*** 400
*
400 M6 4
50PT5*** 400
*
400 M6 4
42PT3*** 400
*
400 M6 4
50PT3*** 400
*
400 M6 4
■ We recommend the use of a LG Brand wall mounting
bracket when mounting the TV to a wall.
■ We recommend that you purchase a wall mounting
bracket which supports VESA standard.
■ LG recommends that wall mounting be performed
by a qualified professional installer.
!
?

►Should Install wall mount on a solid wall
perpendicular to the floor.
►Should use a special wall mount, if you
want to install it to ceiling or slanted wall.
►The surface that wall mount is to be
mounted on should be of sufficient
strength to support the weight of TV set;
e.g. concrete, natural rock, brick and hol-
low block.
►Installing screw type and length depends
on the wall mount used. Further informa-
tion, refer to the instructions included with
the mount.
►LG is not liable for any accidents or dam-
age to property or TV due to incorrect
installation:
- Where a non-compliant VESA wall
mount is used.
- I Incorrect fastening of screws to surface
which may cause TV to fall and cause
personal injury
- Not following the recommended
Installation method.
AA
BB
■ The TV can be installed in various ways such as
on a wall, or on a desktop etc.
■ The TV is designed to be mounted horizontally.
10 cm
10 cm
10 cm
10 cm


For adequate ventilation allow a clearande of 10 cm
(4 Inches) all around the TV.
Power Supply
Circuit breaker

Ensure that you connect the earth wire to prevent
possible electric shock. If grounding methods are
not possible, have a qualified electrician install a
separate circuit breaker.
Do not try to earth the TV by connecting it to tele-
phone wires, lightening rods or gas pipes.
A-11
PREPARATION
Home

POWER
ENERGY
SAVING
AV MODE
INPUT
TV
Switches the TV on from standby or off to standby.
Adjust the power saving mode of the TV.
It helps you select and set images and sounds
when connecting AV devices.(
p.28)
External input mode rotate in regular sequence.
Switches the TV on from standby.
Selects TV channel.
0 to 9 number
button
LIST
Q.VIEW
VOLUME UP
/DOWN
MARK
FAV
RATIO
MUTE
PAGE UP/
DOWN
Programme
UP/DOWN
Selects a programme.
Selects numbered items in a menu.
Displays the programme table.
Returns to the previously viewed programme.
Adjusts the volume.
Check and un-check programmes in the USB
menu.
Displays the selected favourite programme.
Selects your desired picture format.
Switches the sound on or off.
Move from one full set of screen information to the
next one.
Selects a programme.
TELETEXT
BUTTONS
These buttons are used for teletext.
For further details, see the ‘Teletext’ section.(
p.74)
Coloured
buttons
These buttons are used for teletext (on 
models only), 
When using the remote control, aim it at the remote control sensor on the TV.
■ Image shown may differ from your TV.
A-12

PREPARATION
Home

■ Open the battery compartment cover on the back and install
the batteries matching correct polarity (+with +,-with -).
■ Install two 1.5 V AAA batteries. Do not mix old or used batteries
with new ones.
■ Close cover.
■ To remove the batteries, perform the installation a actions in
reverse








Controls the USB menu.
Selects a menu.
Clears all on-screen displays and returns to TV view-
ing from any menu.
Select the desired quick menu source.(
p.14)
Allows you to navigate the on-screen menus and
adjust the system settings to your preference
Accepts your selection or displays the current mode.
Allows the user to move return one step in an inter
active application, EPG or other user interaction
function.
See a list of AV devices connected to TV.
When you toggle this button, the Simplink menu
appears at the screen.(
p.25)
Clears all on-screen displays and returns to TV view-
ing from any menu.




Controls SIMPLINK or USB menu.
Pause the present picture at the screen. (It doesn't
work at USB, Simplink Mode.)
The TV returns to normal viewing automatically if
no signal is received or no operation is performed
for 5 minutes.
■ Image shown may differ from your TV.
EXTERNAL EQUIPMENT SETUP
IN
RS-232C IN
(CONTROL&SERVICE)
ANTENNA
IN
COMPONENT IN
AV IN 1
AUDIO
VIDEO
L(MONO)
R
AUDIO
VIDEO
1
2
2
VARIABLE AUDIO OUT
AV IN2
IN 3
AUDIO IN
(RGB/DVI)
RGB IN
(PC)
/DVI IN
1
IN
RS-232C IN
(CONTROL&SERVICE)
ANTENNA
IN
COMPONENT IN
AV IN 1
AUDIO
VIDEO
L(MONO)
R
AUDIO
VIDEO
1
1
2
VARIABLE AUDIO OUT
AV IN2
IN 2

■ For optimum picture quality, adjust antenna direction.
■ An antenna cable and converter are not supplied.
■ To prevent damage do not connect to the mains outlet until all connections are made between the devices.
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)






RF Coaxial Wire (75
Ω)





■ In poor signal areas, to achieve better picture quality it may be necessary to install a signal amplifier
to the antenna as shown above.
■ If signal needs to be split for two TVs, use an antenna signal splitter for connection.

IN
RS-232C IN
(CONTROL&SERVICE)
ANTENNA
IN
COMPONENT IN
AV IN 1
AUDIO
VIDEO
L(MONO)
R
AUDIO
VIDEO
1
2
2
VARIABLE AUDIO OUT
AV IN2
IN 3
AUDIO IN
(RGB/DVI)
RGB IN
(PC)
/DVI IN
1

EXTERNAL EQUIPMENT SETUP
/DVI IN
R
S-232C I
N
(
CONTROL&SERVICE
)
ANTENNA
IN
COMPONENT IN
A
V IN
1
AUDIO
VIDEO
VIDEO
1
1
2
AV IN2
IN 2
A
UDI
O
I
N
(
RGB/DVI
)
R
G
B IN
(
P
C)
/DVI IN
RS
-232
C
I
N
(CO
NTR
O
L
&S
ERVI
C
E
)
ANTENNA
IN
CO
MP
O
NENT I
N
AV IN 1
AU
DI
O
V
IDE
O
VIDEO
1
1
2
A
UDI
O
IN
(
RGB/DVI
)
RG
B IN
(
PC
)
/DVI IN
RS
-2
3
2
C
I
N
(
CONTROL&SERVICE
)
A
NTENN
A
IN
CO
MP
O
NENT IN
A
V IN
1
A
UDI
O
V
IDE
O
VIDEO
1
1
2
AUDIO IN
(RGB/DVI)
R
G
B IN
(
PC
)
DVI-PC OUTPUT
AUDIO
/DVI IN
RS
-2
3
2
C
I
N
(
CONTROL&SERVICE
)
A
NTENN
A
IN
CO
MP
O
NENT IN
AV IN 1
AU
DI
O
V
IDE
O
L(MONO)
R
AUDIO
VIDEO
1
1
2
VARIABLE AUDIO OUT
A
UDI
O
I
N
(
RGB/DVI
)
RG
B IN
(
P
C)
LR
VIDEO
L
R
S-VIDEO
VIDEO
OUTPUT
SWITCH
ANT IN
ANT OUT
/DVI IN
R
S-232C I
N
(
CONTROL&SERVICE
)
ANTENNA
IN
CO
MP
O
NENT I
N
AV IN 1
AU
DI
O
V
IDE
O
R
AUDIO
VIDEO
1
1
2
VARIABLE AUDIO OUT
A
UDI
O
I
N
(
RGB/DVI
)
R
G
B IN
(
P
C)
/DVI IN
RS
-232
C
I
N
(CO
NTR
O
L
&S
ERVI
C
E
)
ANTENNA
I
N
CO
MP
O
NENT I
N
A
V IN
1
AU
DI
O
V
IDE
O
L(
MONO)
R
AUDIO
VIDEO
1
1
2
VARIABLE AUDIO OUT
A
UDIO IN
(
RGB/DVI
)
R
G
B IN
(
PC
)
/DVI IN
RS
-2
3
2
C
IN
(
CONTROL&SERVICE
)
ANTENNA
IN
CO
MP
O
NENT I
N
A
V IN
1
A
UDIO
V
IDE
O
1
1
2
AUDIO IN
(RGB/DVI)
RGB IN
(PC)
RGB OUTPUT
AUDIO
OUTPUT
SWITCH
ANT IN
R
S-VIDEO VIDEO
ANT OUT
L

■ To avoid damaging any equipment, never plug in any power cord until you have finished connecting
all equipment.
■ This section on EXTERNAL EQUIPMENT SETUP mainly uses diagrams for the 42/50PT2*** models.
■ Image shown may differ from your TV.
Signal Component HDMI
480i/576i
O X
480p/576p
O O
720p/1080i
O O
1080p
O
(50/60Hz only)
O
(24Hz/30Hz/50Hz/60Hz)

To achieve better picture quality, connect a DVD player to the component input ports as shown below.
Component ports on the TV Y PB PR
Video output ports
on DVD player
Y P
B PR
Y B-Y R-Y
Y Cb Cr
Y Pb Pr
1
Connect the video outputs
(
Y, PB, PR
)
of the
external equipment (digital set-top box, DVD,
etc.) to the  jacks on
the TV.
Connect the audio outputs
(
Y, P
B, PR
)
of the
external equipment (digital set-top box, DVD,
etc.) to the  jacks on
the TV.
3
Turn on the external equipment.
(
Refer to the external equipment's manual for
operating instructions.)
4
Select  input source using the
 button on the remote control.
If connected to , select
 input source.
2
EXTERNAL EQUIPMENT SETUP
/DVI IN
R
S-232C I
N
(
CONTROL&SERVICE
)
ANTENNA
IN
COMPONENT IN
A
V IN
1
AUDIO
VIDEO
VIDEO
1
1
2
AV IN2
IN 2
A
UDI
O
I
N
(
RGB/DVI
)
R
G
B IN
(
P
C)
/DVI IN
RS
-232
C
I
N
(CO
NTR
O
L
&S
ERVI
C
E
)
ANTENNA
IN
CO
MP
O
NENT I
N
AV IN 1
AU
DI
O
V
IDE
O
VIDEO
1
1
2
A
UDI
O
IN
(
RGB/DVI
)
RG
B IN
(
PC
)
/DVI IN
RS
-2
3
2
C
I
N
(
CONTROL&SERVICE
)
A
NTENN
A
IN
CO
MP
O
NENT IN
A
V IN
1
A
UDI
O
V
IDE
O
VIDEO
1
1
2
AUDIO IN
(RGB/DVI)
R
G
B IN
(
PC
)
DVI-PC OUTPUT
AUDIO
/DVI IN
RS
-2
3
2
C
I
N
(
CONTROL&SERVICE
)
A
NTENN
A
IN
CO
MP
O
NENT IN
AV IN 1
AU
DI
O
V
IDE
O
L(MONO)
R
AUDIO
VIDEO
1
1
2
VARIABLE AUDIO OUT
A
UDI
O
I
N
(
RGB/DVI
)
RG
B IN
(
P
C)
LR
VIDEO
L
R
S-VIDEO
VIDEO
OUTPUT
SWITCH
ANT IN
ANT OUT
/DVI IN
R
S-232C I
N
(
CONTROL&SERVICE
)
ANTENNA
IN
CO
MP
O
NENT I
N
AV IN 1
AU
DI
O
V
IDE
O
R
AUDIO
VIDEO
1
1
2
VARIABLE AUDIO OUT
A
UDI
O
I
N
(
RGB/DVI
)
R
G
B IN
(
P
C)
/DVI IN
RS
-232
C
I
N
(CO
NTR
O
L
&S
ERVI
C
E
)
ANTENNA
I
N
CO
MP
O
NENT I
N
A
V IN
1
AU
DI
O
V
IDE
O
L(
MONO)
R
AUDIO
VIDEO
1
1
2
VARIABLE AUDIO OUT
A
UDIO IN
(
RGB/DVI
)
R
G
B IN
(
PC
)
/DVI IN
RS
-2
3
2
C
IN
(
CONTROL&SERVICE
)
ANTENNA
IN
CO
MP
O
NENT I
N
A
V IN
1
A
UDIO
V
IDE
O
1
1
2
AUDIO IN
(RGB/DVI)
RGB IN
(PC)
RGB OUTPUT
AUDIO
OUTPUT
SWITCH
ANT IN
R
S-VIDEO VIDEO
ANT OUT
L


2
!
?

►Check that your HDMI cable is High Speed HDMI Cable.
If the HDMI cables are not High Speed HDMI Cable, flickering or no screen display can result.
Please use the High Speed HDMI Cable.
► HDMI mode supports PCM audio format only.
► Audio format was reseted to Dolby/DTS/Bitstrem in DVD Player or STB, it should be changed to PCM.
► We recommend using under 10m of the HDMI cable. When using over the length, connect an ampli-
fier or repeater.
► If the DVD does not support Auto HDMI, you must set the output resolution appropriately.
1
Connect the HDMI output of the external equip-
ment (digital set-top box, DVD, etc.) to 
,  or (Except for
42/50PT2***, 50PV2***)jack on the TV.
2
Turn on the external equipment.
3
Select or(Except for
42/50PT2***, 50PV2***) input source using the
 button on the remote control.

EXTERNAL EQUIPMENT SETUP
L - AUDIO OUT - R
L R
VIDEO
DVI-PC OUTPUT
AUDIO
AV IN2
COMPONENT IN
AUDIO
VIDEO
AV IN2
ANTENNA
IN
L(MONO)
R
AUDIO
VIDEO
AV IN1
1
AUDIO IN
(RGB/DVI)
USB IN
SERVICE ONLY
RGB IN
(PC)
RS-232C IN
(CONTROL)
26/32LD330
2
AUDIO IN
(RGB/DVI)
USB IN
SERVICE ONLY
RGB IN
(PC)
COMPONENT IN
VIDEO
LY P
B
P
R
R
AUDIO
AV IN1
VIDEO
AUDIO
/MONO
ANTENNA
IN
/DVI IN
1
2
RS-232C IN
(CONTROL)
AUDIO IN
(RGB/DVI)
RGB IN
(PC)
AV IN1
VIDEO
AUDIO
/MONO
ANTENNA
IN
/DVI IN
1
2
RS-232C IN
(CONTROL)
COMPONENT IN
AUDIO
VIDEO
AUDIO IN
(RGB/DVI)
RGB IN
(PC)
COMPONENT IN
VIDEO
LY P
B
P
R
R
AUDIO
AV IN1
VIDEO
AUDIO
/MONO
ANTENNA
IN
RS-232C IN
(CONTROL)
1
2
RGB IN
(PC)
COMPONENT IN
VIDEO
LY P
B
P
R
R
AUDIO
AV IN1
VIDEO
AUDIO
/MONO
ANTENNA
IN
RS-232C IN
(CONTROL)
1
AUDIO IN
(RGB/DVI)
AUDIO IN
(RGB/DVI)
RGB IN
(PC)
COMPONENT IN
VIDEO
LY P
B
P
R
R
AUDIO
AV IN1
VIDEO
AUDIO
/MONO
/DVI IN
1
2
RS-232C IN
(CONTROL)
ANTENNA
IN
OUTPUT
SWITCH
ANT IN
R
S-VIDEO VIDEO
ANT OUT
L
COMPONENT IN
VIDEO
LY P
B
P
R
R
AUDIO
AV IN1
VIDEO
AUDIO
/MONO
ANTENNA
IN
/DVI IN
1
2
RS-232C IN
(CONTROL)
RGB IN
(PC)
AUDIO IN
(RGB/DVI)
RGB OUTPUT
AUDIO
AV IN2
L
R
S-VIDEO
VIDEO
OUTPUT
SWITCH
ANT IN
ANT OUT
AUDIO IN
(RGB/DVI)
RGB IN
(PC)
COMPONENT IN
VIDEO
LY P
B
P
R
R
AUDIO
AV IN1
VIDEO
AUDIO
/MONO
ANTENNA
IN
/DVI IN
1
2
RS-232C IN
(CONTROL)
AUDIO IN
(RGB/DVI)
USB IN
SERVICE ONLY
RGB IN
(PC)
COMPONENT IN
VIDEO
LY P
B
P
R
R
AUDIO
AV IN1
VIDEO
AUDIO
/MONO
ANTENNA
IN
RS-232C IN
(CONTROL)
1
2
AUDIO IN
(RGB/DVI)
USB IN
SERVICE ONLY
RGB IN
(PC)
COMPONENT IN
VIDEO
LY P
B
P
R
R
AUDIO
ANTENNA
IN
/DVI IN
1
2
RS-232C IN
(CONTROL)
L(MONO)
R
AUDIO
VIDEO
AV IN
L
R
S-VIDEO
VIDEO
OUTPUT
SWITCH
ANT IN
ANT OUT
AUDIO IN
(RGB/DVI)
USB IN
SERVICE ONLY
RGB IN
(PC)
COMPONENT IN
VIDEO
LY P
B
P
R
R
AUDIO
ANTENNA
IN
/DVI IN
1
2
RS-232C IN
(CONTROL)
L(MONO)
R
AUDIO
VIDEO
AV IN
L R
VIDEO
/DVI IN
/DVI IN
/DVI IN
/DVI IN
2
L - AUDIO OUT - R
L - AUDIO OUT - R
L - AUDIO OUT - R
L - AUDIO OUT - R
/DVI IN
R
S-232C I
N
(
CONTROL&SERVICE
)
ANTENNA
IN
COMPONENT IN
A
V IN
1
AUDIO
VIDEO
VIDEO
1
1
2
AV IN2
IN 2
A
UDI
O
I
N
(
RGB/DVI
)
R
G
B IN
(
P
C)
/DVI IN
RS
-232
C
I
N
(CO
NTR
O
L
&S
ERVI
C
E
)
ANTENNA
IN
CO
MP
O
NENT I
N
AV IN 1
AU
DI
O
V
IDE
O
VIDEO
1
1
2
A
UDI
O
IN
(
RGB/DVI
)
RG
B IN
(
PC
)
/DVI IN
RS
-2
3
2
C
I
N
(
CONTROL&SERVICE
)
A
NTENN
A
IN
CO
MP
O
NENT IN
A
V IN
1
A
UDI
O
V
IDE
O
VIDEO
1
1
2
AUDIO IN
(RGB/DVI)
R
G
B IN
(
PC
)
DVI-PC OUTPUT
AUDIO
/DVI IN
RS
-2
3
2
C
I
N
(
CONTROL&SERVICE
)
A
NTENN
A
IN
CO
MP
O
NENT IN
AV IN 1
AU
DI
O
V
IDE
O
L(MONO)
R
AUDIO
VIDEO
1
1
2
VARIABLE AUDIO OUT
A
UDI
O
I
N
(
RGB/DVI
)
RG
B IN
(
P
C)
LR
VIDEO
L
R
S-VIDEO
VIDEO
OUTPUT
SWITCH
ANT IN
ANT OUT
/DVI IN
R
S-232C I
N
(
CONTROL&SERVICE
)
ANTENNA
IN
CO
MP
O
NENT I
N
AV IN 1
AU
DI
O
V
IDE
O
R
AUDIO
VIDEO
1
1
2
VARIABLE AUDIO OUT
A
UDI
O
I
N
(
RGB/DVI
)
R
G
B IN
(
P
C)
/DVI IN
RS
-232
C
I
N
(CO
NTR
O
L
&S
ERVI
C
E
)
ANTENNA
I
N
CO
MP
O
NENT I
N
A
V IN
1
AU
DI
O
V
IDE
O
L(
MONO)
R
AUDIO
VIDEO
1
1
2
VARIABLE AUDIO OUT
A
UDIO IN
(
RGB/DVI
)
R
G
B IN
(
PC
)
/DVI IN
RS
-2
3
2
C
IN
(
CONTROL&SERVICE
)
ANTENNA
IN
CO
MP
O
NENT I
N
A
V IN
1
A
UDIO
V
IDE
O
1
1
2
AUDIO IN
(RGB/DVI)
RGB IN
(PC)
RGB OUTPUT
AUDIO
OUTPUT
SWITCH
ANT IN
R
S-VIDEO VIDEO
ANT OUT
L

Connect the USB device to the jack on the TV.
After connecting the jack, you use the function. (
)
2
1

or
1
Connect the digital set-top box or the DVI out-
put of the PC to jack on the
TV.
2
Connect the audio output of the digital set-top
box or the PC audio output to the 
jack on the TV.
3
Turn on the digital set-top box or the PC and
the TV.
(
Refer to the digital set-top box or the PC
manual for operating instructions.)
4
Select input source using the 
button on the remote control.
/