Echo CS-400 User manual

X7503255902

Operator’s

Manual

CS-400

CHAIN SAW

The engine exhaust from this product contains chemicals

known to the State of California to cause cancer, birth defects,

or other reproductive harm.

Read and understand all provided literature before use.

Failure to do so could result in serious injury.

TABLE OF CONTENTS CS-400

2 X7503255902

TABLE OF CONTENTS

Introduction ................................................................................................. 4

Servicing Information .................................................................................. 4

Parts/Serial Number............................................................................. 4

Service................................................................................................. 5

ECHO Consumer Product Support...................................................... 5

Product Registration ............................................................................ 5

Additional Literature............................................................................. 5

Packing List................................................................................................. 5

Safety.......................................................................................................... 6

Rules For Safe Operation .................................................................... 6

Correct Use Of Chain Brake ................................................................ 7

Personal Condition and Safety Equipment ........................................ 12

International Symbols ........................................................................ 16

Manual Safety Symbols and Important Information........................... 18

Emission Control (Exhaust & Evaporative) .............................................. 19

CARB And EPA Emissions Control Information ................................ 19

Description ................................................................................................ 20

Preparation For Use........................................................................... 22

Operation .................................................................................................. 25

Fuel.................................................................................................... 25

Chain Lubricant.................................................................................. 28

Winter Operation................................................................................ 29

Starting Cold Engine.......................................................................... 30

Starting Warm Engine........................................................................ 32

Running ............................................................................................. 33

Stopping............................................................................................. 34

Checking Chain Tension.................................................................... 34

Chain Lubrication Test....................................................................... 34

Cutting Instructions ............................................................................ 35

Chain And Guide Bar Combination.................................................... 39

Guide Bar........................................................................................... 39

Saw Chain ......................................................................................... 40

CS-400 TABLE OF CONTENTS

X7503255902 3

Maintenance ............................................................................................. 40

Skill Levels ........................................................................................ 41

Maintenance Intervals ....................................................................... 41

Carburetor Adjustment ...................................................................... 42

Air Filter ............................................................................................. 44

Spark Plug......................................................................................... 44

Check Fuel System ........................................................................... 44

Fuel Filter .......................................................................................... 44

Automatic Oiler.................................................................................. 45

Oil Filter ............................................................................................. 45

Guide Bar .......................................................................................... 46

Sprocket ............................................................................................ 46

Cooling System Cleaning .................................................................. 46

Spark Arrestor Muffler ....................................................................... 47

Spark Arrestor Screen....................................................................... 47

Exhaust Port Cleaning....................................................................... 48

Setting The Saw Chain...................................................................... 49

Troubleshooting........................................................................................ 52

Storage ..................................................................................................... 54

Storage After Use.............................................................................. 54

Specifications ........................................................................................... 55

Product Registration ................................................................................. 56

Notes ........................................................................................................ 58

INTRODUCTION CS-400

4 X7503255902

INTRODUCTION

Specifications, descriptions and illustrative material in this literature are as

accurate as known at the time of publication, but are subject to change

without notice. Illustrations may include optional equipment and

accessories, and may not include all standard equipment.

Read and understand all provided literature.

Literature contains specifications and

information for safety, operation,

maintenance, storage and assembly specific

to this product. Scan QR codes for more

information.

For additional literature, including safety manuals where applicable, or

questions regarding terms used in this manual, visit:

https://www.echo-usa.com/manuals

OR

https://www.shindaiwa-usa.com/manuals

SERVICING INFORMATION

Parts/Serial Number

Genuine ECHO Parts and

Assemblies for your ECHO products

are available only from an Authorized

ECHO Dealer. When you do need to

buy parts always have the Model

Number and Serial Number of the unit

with you. For future reference write

them in the space provided below.

Model No. _______________ Serial No. _______________

CS-400 PACKING LIST

X7503255902 5

Service

Service of this product during the warranty period must be performed by an

Authorized ECHO Service Dealer. For the name and address of the

Authorized ECHO Service Dealer nearest you, ask your retailer or call:

1-800-432-ECHO (3246). Dealer information is also available on our Web

Site www.echo-usa.com. When presenting your unit for Warranty service/

repairs, proof of purchase is required.

ECHO Consumer Product Support

If you require assistance or have questions concerning the application,

operation, or maintenance of this product, call the ECHO Consumer

Product Support Department at 1-800-432-ECHO (3246) from 8:00 am to

5:00 pm (Central Standard Time) Monday through Friday. Before calling,

please know the model and serial number of your unit.

Product Registration

Register your ECHO equipment on-line at www.echo-usa.com or by filling

out the product registration sheet included in this manual. Registering your

product confirms warranty coverage and provides a direct link to ECHO if

we find it necessary to contact you.

Additional Literature

In addition to finding information online, information is available from your

Authorized ECHO Service Dealer, or by contacting ECHO Inc., 400

Oakwood Road, Lake Zurich, IL 60047 (1-800-432-ECHO (3246)).

PACKING LIST

The ECHO product you purchased has been factory pre-assembled for your

convenience. Due to packaging restrictions, some assembly may be

necessary.

After opening the carton, check for damage. Immediately notify your retailer

or ECHO Dealer of damaged or missing parts. Use the contents list to check

for missing parts.

1 Power Head

1 Operator's Manual

1 Warranty Statement

1 Guide Bar

1 Saw Chain

SAFETY CS-400

6 X7503255902

SAFETY

Rules For Safe Operation

Kickback Safety Precautions for Chain Saw Users

KICKBACK may occur when the nose or tip of the guide bar

touches an object, or when the wood closes in and pinches the

saw chain in the cut.

Tip contact in some cases may cause

a lightning fast reverse REACTION,

kicking the guide bar up and back

towards the operator. Pinching the

saw chain along the top of the guide

bar may push the guide bar rapidly

back towards the operator. Either of

these reactions may cause you to

lose control of the saw which could

result in serious personal injury.

The optional Kick Guard

TM

device is

not installed on the guide bar when

you purchase your chain saw. The

optional Kick Guard

TM

can be used in

a majority of cutting operations, and is

especially recommended for

beginners, homeowners, or chain saw

novices. Most cutting operations can

be accomplished with the optional

Kick Guard

TM

in place.

Do not rely exclusively upon the safety devices built into your saw. As a

chain saw user, you should take several steps to keep your cutting jobs free

from accident or injury.

1. With a basic understanding of

kickback, you can reduce or

eliminate the element of surprise.

Sudden surprise contributes to

accidents.

Rotational kickback

Chain moving downward at impact

Kickback Danger Zone

CS-400 SAFETY

X7503255902 7

2. Keep a good firm grip on the saw with both hands, the right hand on the

rear handle, and the left hand on the front handle, when the engine is

running. Use a firm grip with thumbs and fingers encircling the chain

saw handles. A firm grip will help you reduce kickback and maintain

control of the saw. Don’t let go.

3. Make sure that the area in which

you are cutting is free from

obstructions. Do not let the nose

of the guide bar contact a log,

branch, or any other obstruction

which could be hit while you are

operating the saw.

4. Cut at high engine speeds.

5. Do not overreach or cut above

shoulder height.

6. Follow manufacturer’s sharpening and maintenance instructions for the

saw chain.

7. Only use replacement bars and chains specified by the manufacturer or

the equivalent.

Correct Use Of Chain Brake

Chain Brake Operation

• Set the lever in the unlocked

position before starting to cut.

• If the brake is tripped by kickback

reaction, the chain will stop

immediately. Release the throttle to

avoid possible damage to the

engine or clutch.

• Do not attempt to operate the

engine with the brake locked.

Testing The Brake

• Start the engine on a solid level

surface and run at a fast idle until

warm.

• Hold the saw firmly by the handles

and accelerate the engine to a fast

idle.

Linear kickback

Kickback

Pinch

Locked

Shown with optional

Kick Guard

TM

Unlocked

Shown with optional

Kick Guard

TM

SAFETY CS-400

8 X7503255902

• Slowly operate the chain brake lever while holding the saw firmly on the

ground. When the brake lever trips, the chain should stop. Immediately

release the throttle trigger.

Do not allow the saw to tip forward in order to avoid damage to the

chain.

If the chain does not stop immediately, return the saw to your

authorized dealer for repair.

Note:

• For practice, while cutting a small tree, push the lever forward to lock

the brake.

• Confirm that the brake works properly before each use.

• If the chain brake is clogged with wood chips, function of the brake may

deteriorate. Always keep the device clean.

• Do not increase engine RPM while the chain brake is locked.

Do not use a a bar and chain combination other than those specified in this

manual.

For your own safety, do not remove the chain brake system.

The installation of a chain brake may be mandatory by law or as stipulated

by insurance regulations in your area of operation. You should inquire

through local government offices, your employer or your local dealer to

ensure that your chain saw conforms to the required safety standard.

Chain brakes have been designed and tested to comply with international

safety standards as follows:

USA: ANSI Standard B175.1 Safety Requirement for chain saws

Canada: CSA Standard Z62.1, Z62.3

CS-400 SAFETY

X7503255902 9

ANSI Standard B175.1 and CSA

Z62.1.3 stipulate that the brake

shall stop the chain 0.12

seconds at an engine speed of

13,500 r/min. It is the

responsibility of the owner/

operator to ensure that the

brake is serviced, adjusted and

tested strictly in accordance

with the instructions as detailed

here in order to ensure that the

brake performance is

maintained in compliance with

the Standards B175.1 and CSA

Z62.1.3

Automatic Chain Brake

Kickback produced from the tip of the guide bar will trip the automatic chain

brake. To make sure that the automatic chain brake operates properly, follow

these steps:

1. Stop the engine.

2. Hold the saw with the guide bar approximately 35 cm (14 inches) above

a wooden surface. Right hand should hold the rear handle, and left

hand should hold the front handle.

3. Release the front handle and drop the end of the guide bar against the

wooden surface.

4. The impact should lock the chain brake.

When checking the operation of the automatic chain brake, use a soft

surface substance like wood to absorb the impact so the chain is not

damaged.

35 cm

(14 in.)

SAFETY CS-400

10 X7503255902

Other Safety Precautions

1. Do not operate a chain saw with one hand! Serious injury to the

operator, helpers, bystanders, or any combination of these persons

may result from one-handed operation. A chain saw is intended for two-

handed use.

2. Do not operate a chain saw when you are fatigued.

3. Use safety footwear, snug-fitting clothing and protective gloves. Wear

eye, hearing, and head protection devices.

4. Use caution when handling fuel. Move the chain saw at least 3 m (10

feet) from the fueling point before starting the engine.

5. Do not allow other persons to be near the chain saw when starting or

cutting with the chain saw. Keep bystanders and animals out of the

work area.

6. Do not start cutting until you have a clear work area, secure footing,

and a planned retreat path from the falling tree.

7. Keep all parts of your body away from the saw chain when the engine is

running.

8. Before you start the engine, make sure that the saw chain is not

contacting anything.

9. Carry the chain saw with the engine stopped, the guide bar and saw

chain to the rear, and the muffler away from your body.

10. Do not operate a chain saw that is damaged, improperly adjusted, or

not completely and securely assembled. Be sure that the saw chain

stops moving when the throttle control trigger is released.

11. Shut off the engine before setting the chainsaw down.

12. Use extreme caution when cutting small size brush and saplings

because slender material may catch the saw chain and be whipped

toward you or pull you off balance.

13. When cutting a limb that is under tension, be alert for spring-back so

that you will not be struck when the tension in the wood fibers is

released.

14. Keep the handles dry, clean, and free of oil or fuel mixture.

15. Operate the chainsaw only in well ventilated areas.

16. Do not operate a chainsaw in a tree unless you have been specifically

trained to do so.

17. All chain saw service, other than items listed in the Instruction manual

maintenance instructions, should be performed by competent service

personnel. (For example, if improper tools are used to remove the

flywheel or if an improper tool is used to hold the flywheel in order to

remove the clutch, structural damage to the flywheel could occur and

could subsequently cause the flywheel to burst.)

CS-400 SAFETY

X7503255902 11

18. When transporting your chain saw, use the appropriate guide bar

scabbard.

19. A spark arrestor muffler approved to SAE Standard J335 is standard on

this chain saw to reduce the possibility of forest fires. Do not operate

the chain saw with a loose or defective muffler. Do not remove the

spark arrestor screen.

20. When using a chainsaw a fire extinguisher should be available.

21. When felling, keep at least 2 tree lengths between yourself and your

fellow workers.

22. Follow instructions in your operator’s manual for starting the chain saw.

23. Never adjust the guide bar or sawchain when the engine operating.

24. When boring with the chainsaw, the initial cut should be introduced with

the lower part of the nose (tip) until the hole is sufficiently large so as to

introduce the entire nose (tip) of the guide bar. This technique should

reduce the danger of kickback.

25. Allow your chainsaw to cool before refueling, and do not smoke while

refueling.

Chain saws shall be used in accordance with the operating

instructions and safety precautions listed in the operator's

manual(s). It shall be the responsibility of the owner to see that

such instructions and precautions are given to every operator

who uses the saw.

◆ During operation, the muffler or catalytic muffler and

surrounding cover become hot.

◆ Never suspend the saw on a lanyard with the engine

running.

◆ Always use the saw from the right-hand side of your body –

NEVER from the left side.

◆ Always wear proper safety clothing to protect your lower

body from sharp saw chain and hot muffler.

◆ Always keep exhaust area clear of flammable debris during

transportation or when storing, otherwise serious property

damage or personal injury may result.

SAFETY CS-400

12 X7503255902

Moving parts can amputate fingers or cause severe injuries.

Keep hands, clothing and loose objects away from all openings.

◆ ALWAYS stop engine, disconnect spark plug, and make

sure all moving parts have come to a complete stop before

removing obstructions, clearing debris, or servicing unit.

◆ DO NOT start or operate unit unless all guards and

protective covers are properly assembled to unit.

◆ NEVER reach into any opening while the engine is running.

Moving parts may not be visible through openings.

Using improper replacement components or removing safety

devices may result in serious or fatal injury.

Periodically Check fuel system (fuel lines, vent, grommet, fuel

tank, and fuel cap) for leaks especially if the unit is dropped. If

damage or leaks are found, do not use unit, otherwise serious

personal injury or property damage may occur. Have unit

repaired by an authorized servicing dealer before using.

Personal Condition and Safety Equipment

Cancer and Reproductive Harm

www.P65Warnings.ca.gov

The muffler or catalytic muffler and surrounding cover

may become extremely hot. Always keep clear of

exhaust and muffler area, otherwise serious personal

injury may occur.

CS-400 SAFETY

X7503255902 13

Users of this product risk injury to themselves and others if the

unit is used improperly and/or safety precautions are not

followed. Proper clothing and safety gear must be worn when

operating unit.

Physical Condition

Your judgment and physical dexterity may not be good:

• If you are tired or sick

• If you are taking medication

• If you have taken alcohol or drugs

Operate unit only if you are physically and mentally well.

Eye Protection

◆ Eye protection that meets ANSI Z87.1 or CE requirements

must be worn whenever you operate the unit.

◆ For additional safety, a full-face shield may be worn over

safety glasses or goggles to provide protection from sharp

branches or flying debris.

Hand Protection

Wear sturdy, no-slip, rubber work gloves to improve your grip on the

handles. Gloves also provide protection against cuts and scratches, cold

environments, and reduce the transmission of machine vibration to your

hands.

Hearing/Ear Protection

ECHO recommends wearing personal protection whenever unit is used.

Breathing Protection

Operators who are sensitive to dust or other common airborne allergens

may need to wear a dust mask to prevent inhaling these materials while

operating unit. Dust masks can provide protection against dust, plant debris,

and other plant matter such as pollen. Make sure the mask does not impair

your vision, and replace the mask as needed to prevent air restrictions.

SAFETY CS-400

14 X7503255902

Proper Clothing

Wear snug-fitting, durable clothing:

• Pants should have long legs, shirts should have long sleeves.

• DO NOT WEAR SHORTS.

• DO NOT WEAR TIES, SCARVES, JEWELRY, or clothing with loose or

hanging items that could become entangled in moving parts or

surrounding growth.

• Keep clothing buttoned or zipped, and keep shirt tails tucked in.

Wear sturdy work shoes with nonskid rubber soles:

• DO NOT WEAR OPEN TOED SHOES.

• DO NOT OPERATE UNIT BAREFOOTED.

Keep long hair away from engine and air intake. Retain hair with cap or net.

Heavy protective clothing can increase operator fatigue, which may lead to

heat stroke. Schedule heavy work for early morning or late afternoon hours

when temperatures are cooler.

The components of this machine generate an electromagnetic

field during operation, which may interfere with some

pacemakers. To reduce the risk of serious or fatal injury,

persons with pacemakers should consult with their physician

and the pacemaker manufacturer before operating this

machine. In the absence of such information, ECHO does not

recommend the use of this machine by anyone who has a

pacemaker.

Extended Operation / Extreme Conditions

Prolonged exposure to cold and/or vibration may result in

injury. Read and follow all safety and operation instructions to

minimize risk of injury. Failure to follow instructions may result

in painful wrist/hand/arm injuries.

CS-400 SAFETY

X7503255902 15

It is believed that a condition called Raynaud’s Phenomenon, which affects

the fingers of certain individuals, may be brought about by exposure to

vibration and cold. Exposure to vibration and cold may cause tingling and

burning sensations, followed by loss of color and numbness in the fingers.

The following precautions are strongly recommended, because the

minimum exposure, which might trigger the ailment, is unknown.

• Keep your body warm, especially the head, neck, feet, ankles, hands, and

wrists.

• Maintain good blood circulation by performing vigorous arm exercises

during frequent work breaks, and also by not smoking.

• Limit the hours of operation. Try to fill each day with jobs where operating

the unit or other hand-held power equipment is not required.

• If you experience discomfort, redness, and swelling of the fingers followed

by whitening and loss of feeling, consult your physician before further

exposing yourself to cold and vibration.

Repetitive Stress Injuries (RSI)

It is believed that overusing the muscles and tendons of the fingers, hands,

arms, and shoulders may cause soreness, swelling, numbness, weakness,

and extreme pain in those areas. Certain repetitive hand activities may put

you at a high risk for developing a Repetitive Stress Injury (RSI). An extreme

RSI condition is Carpal Tunnel Syndrome (CTS), which could occur when

your wrist swells and squeezes a vital nerve that runs through the area.

Some believe that prolonged exposure to vibration may contribute to CTS.

CTS can cause severe pain for months or even years.

To reduce the risk of RSI/CTS, do

the following:

• Avoid using your wrist in a bent,

extended, or twisted position.

Instead try to maintain a straight

wrist position. Also, when

grasping, use your whole hand,

not just the thumb and index

finger.

• Take periodic breaks to minimize

repetition and rest your hands.

• Reduce the speed and force with

which you do the repetitive

movement.

SAFETY CS-400

16 X7503255902

• Do exercises to strengthen the hand and arm muscles.

• Immediately stop using all power equipment and consult a doctor if you

feel tingling, numbness, or pain in the fingers, hands, wrists, or arms. The

sooner RSI/CTS is diagnosed, the more likely permanent nerve and

muscle damage can be prevented.

All over head electrical conductors and communications wires

can have electricity flow with high voltages. This unit is not

insulated against electrical current. Never touch wires directly

or indirectly, otherwise serious injury or death may result.

Do not operate this product indoors or in inadequately

ventilated areas. Engine exhaust contains poisonous emissions

and can cause serious injury or death.

International Symbols

Symbol Description Symbol Description

WARNING!

Read and follow all

safety precautions in

the instruction manual.

Failure to follow

instructions could result

in serious personal

injury.

Carburetor

Adjustment - High

Speed Mixture

Wear Eye, Ear and

Head Protection

Carburetor

Adjustment - Idle

Speed

Tip contact may cause

the guide bar to move

suddenly upward and

backward, which may

cause serious injury

Carburetor

Adjustment - Low

Speed Mixture

Contact of the guide bar

tip with any object

should be avoided

Emergency Stop

Both of the operator’s

hands must be used to

operate the chain saw

Fuel and Oil Mixture

H

T

L

CS-400 SAFETY

X7503255902 17

Hot Surface Chain Oil Fill

Chain Brake Operation

Chain Oiler

Adjustment

Choke Control “COLD

START” Position

(Choke Closed)

Purge Pump

Measured maximum

kickback value, without

brake, for approved bar

and chain

combinations.

Symbol Description Symbol Description

SAFETY CS-400

18 X7503255902

Manual Safety Symbols and Important Information

Throughout this manual and on the product itself, you will find safety alerts

and helpful, informational messages preceded by symbols or key words.

The following is an explanation of those symbols and key words and what

they mean to you.

The safety alert symbol accompanied by the word “DANGER”

calls attention to an act or condition which WILL lead to serious

personal injury or death if not avoided.

The safety alert symbol accompanied by the word “WARNING”

calls attention to an act or condition which CAN lead to serious

personal injury or death if not avoided.

The safety alert symbol accompanied by the word “CAUTION”

calls attention to an act or condition which may lead to minor or

moderate personal injury if not avoided.

The enclosed message provides information necessary for the

protection of the unit.

Note: This enclosed message provides tips for use, care and

maintenance of the unit.

CIRCLE AND SLASH SYMBOL

This symbol means the specific action shown is prohibited.

Ignoring these prohibitions can result in serious or fatal injury.

CS-400 EMISSION CONTROL

X7503255902 19

EMISSION CONTROL (EXHAUST &

EVAPORATIVE)

CARB And EPA Emissions Control Information

The emission control system for

the engine is EM (engine

modification) and, if the second to

last character of the Engine Family

on the Emission Control

Information label (sample below) is

“B”, “C”, “K”, or “T”, the emission

control system is EM and TWC (3-

way catalyst). The fuel tank/fuel

line emission control system is EVAP (evaporative emissions). Evaporative

emissions for California models are only applicable to fuel tanks and fuel

feed lines.

An Emission Control Label is

located on the engine. (This is an

EXAMPLE ONLY, information on

label varies by engine FAMILY).

Product Emission Durability

(Emission Compliance

Period)

The 50 or 300 hour emission compliance period is the time span selected by

the manufacturer certifying the engine emissions output meets applicable

emissions regulations, provided that approved maintenance procedures are

followed as listed in the Maintenance Section of this manual.

DESCRIPTION CS-400

20 X7503255902

DESCRIPTION

Locate the safety decal(s) on your unit. Make sure the decal(s) is legible and

that you understand and follow the instructions on it. If a decal cannot be

read, a new one can be ordered from your ECHO dealer. Safety label is for

example only. Your label my appear slightly different.

45

Max

16A0CD3757 91PX57CQ

Manual shows other combinations.

Manuel montre d' autres combinaisons.

X5050009390

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

Page is loading ...

Echo CS-400 User manual

Echo CS-400 User manual

Related papers

Other documents